Re: How to share keyboard on Portege R830?

Similar Questions

• How to change keyboard on Portege R830-1?

  I have change the keyboard and I do not know how.

  Please help me

  PT

  Check it please your first post
  http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?threadID=72191

• How to disable WiFi for Portege R830 + Port Replicator & external keyboard

  Stupid question I know, but it's driving me crazy.

  I have an external keyboard Port duplicator and the attached monitor. The Port Replicator has a wired Ethernet connection to my local network. When I anchor my R830 in Port Replicator, ideally I would like to turn off the wireless adapter, but at least I certainly want the default use of the wired LAN connection not WiFi.

  Currently, it seems just randomly decide to use wired or wireless connection when I anchor.

  So, two part question:

  1. How can I pay the R830 automatically default to an Ethernet cable when I anchor?
  2. How can I turn off Wi - Fi when I am connected and using an external keyboard (the toggle F8 to activate wireless switch on the keyboard of the laptop does not work on external keyboards)

  Thank you very much in advance for your advice.

  > How can I set the R830 automatically default to a wired Ethernet connection when I anchor?
  If the port replicator is connected to the local network and then the laptop would use the LAN connection automatically if you connect the R830.

  > How can I turn off Wi - Fi when I am connected and using an external keyboard (the toggle F8 to activate wireless switch on the keyboard of the laptop does not work on external keyboards)
  Well, in this case, you can use the internal keyboard to turn off the WiFi using Fn + F8

• Portege R830-10v / i7 / change internal SSD 225 GB

  Hello

  I need to change my flash drive SSD internal 225 GB for a 512 GB SSD!

  What should I do to the hardware and software level?
  Can I take any SSD?

  Thanks for the help?

  Best regards, Florence

  The HDD or SSD drive update requires no special modifications in the software or hardware.
  You need a compatible player SATA SSD 2.5.

  Here is a nice and very useful document how to upgrade / replace the Portege R830 & Satellite R830 series SSD or HARD disk drive.

  http://APS2.toshiba-tro.de/KB0/CRU18037E0000R01.htm

  Of course, after this upgrade, you'll need to install the system new the best choice would be its use or recovery disk and recover the laptop to factory settings.

• Portege R830 had dead blue when the screen connects to wifi or shared internet

  It seemed began as soon as the automatic update from Microsoft on Qualcomm, Atheros, every time when connect to any WIFi, share internet, my portege R830 shows blue screen and the following error message:
  unhandled system_thread_exception (athwb.sys)

  I found that I am not the isolated on the Web site. I tried to remove and stop updates. However, once I connect to the internet, the blue screen comes back.

  Is the problem because of the network adapter? The model is Qualcomm Atheros AR9002WB
  Can solve the problem if I download the new driver of Qualcomm-Atheros site? Or if I replace a new adapter?

  The athwb.sys file belongs to the Atheros wireless driver. Usually placed in C:\Windows\System32\drivers\athwb.sys
  It seems that in your case this file causing the BSOD.

  I found a very interesting detail about this problem and why it seems.

  A user wrote:
  {quote} The issue is due to a database hosted on Linux kernel mapped NAS drives and if the Client for NFS is installed on the windows machine. For some reason, this configuration does not work. If you mount your shares and NFS is installed it tries to use the NFS client and fails miserably. Trick is to disassemble all the shares of logging in Safe Mode and then rebooted and uninstall the NFS client and then mount your shares. {quote}

• How to connect multiple external monitors to Portege R830

  Anyone has any advice on how to connect more than one external monitor to a Portege R830?

  I have a monitor through the station home, but when I attach a second monitor to the port of the laptop do not recognize at all.

  It is used to work on my old Portege, but for some reason not on the R830.

  Any tips or advice?

  Hello

  You use the same port in the docking station and Portege R830?
  Docking station replica ports in order to use the Portege docking station port or port.

  If you want to connect more than one external monitor to the laptop then I would recommend using something like Toshiba Dynadock
  http://us.Toshiba.com/computers/accessories/dynadock/

  Welcome them

• Portege R830 - fingerprints fingerprints are more recognized

  Hello

  Last week, I bought a Portege R830. I registered my 2 index fingers and everything has worked fine for about 2 days. Now when I put my index fingers, the utility no longer recognizes my impressions, neither one.

  How can I delete the prints and start again? I tried to go to the utility, but since it does not recognize my impression, it does not give me access.

  TIA
  Patricia

  Start the utility of fingerprinting as an administrator and click the button "delete all traces of fingers. He may need to enter a password to give you access.

  If you don't remember the password, you may have to send the laptop in to a Service Center for Toshiba to remove fingerprints.

• Portege R830-10 q - Win 10 upgrade - error 0xc000000f

  I have a Toshiba Portege R830-10 q I'm trying to put Windows 7 upgraded to Windows 10.

  When upgrading, he stumbles and goes into a loop of repair to 29% which gives me error 0xc000000f with no way to roll back.

  A clean installation, installs absolutely perfect, but due to rules of activation of Microsoft (possible only via an update unless you buy the product), it is no good.

  Has anyone managed to upgrade the q R830-10 Windows 10 yet?

  I know that's not on the list of approved of the PC Toshiba, but surely there must be a way

  I also have this problem, anyone can give us advice how to fix this
  Thank you.

  Jonathan

• Portege R830 - problems of 3G connection after installing Win 7 32 bit

  Hello

  I went down a Portege R830 Windows 7 64 bit for Windows 7 32 bit with drivers of Toshiba. I put a SIM from my provider.
  In the windows Network Manager, 7 and in the Toshiba Wireless Manager I can see the right provider and HSPA network but when I start the connection, it does not (I don't have a PIN code).

  It is failed with Windows 7 Network Manager and Manager Toshiba wireless (I don't have this problem with the Portege R700 windows 7 32bits)

  But I found a small solution (but I think that's not enough):
  I have created a dial-up connection, with a number * 99 #,.
  I started the connection, it does not happen, but after that, when I raise my first connection is good.

  I don't know why, it's as if the modem is in sleep and the dial-up connection wake-up the modem, because after all is good (win7 Network Manager, Manager wireless Toshiba) so if I reboot the Portege.

  I want to avoid the dial-up connection on my r700 portege with 32-bit windows 7

  Thanks for your help and sorry for my English.
  support for the toshiba told me to reinstall windows 7 64 bit to solve the problem :)

  Hello

  Are you sure that you have correctly configured the connection?
  Here is a nice FAQ that explains step by step how to connect 3G using the Toshiba Wireless Manager:

  + How to configure and set up a 3G connection via the preinstalled Toshiba Wireless Manager +.
  http://APS2.toshiba-tro.de/KB0/FAQ1A037W0000R01.htm

  and here you can find instruction how to create dial upward of connection using own configuration of Windows.

  + How to create a Dial-Up connection with 3 +.
  http://APS2.toshiba-tro.de/KB0/HTD9802OF0000R01.htm

  Recommend check them both!

• Sound when Portege R830 is anchored and display lid is closed

  I have a fairly new Toshiba Portege R830 laptop (PT321E-01E00YEN) who don't use speakers integrated if it is placed in a dock with the closed laptop screen or the microphone.

  This causes problems when you try to work from only an external monitor, but when I flip the lid open, it works fine.

  I am using a replication of port II (PA3916B) and once installed a month ago, all device etc drivers has been updated to the lasted available so I think that there is a software configuration option that just needs to check or disabling.

  No one knows where that might be?

  I test this on an another older duplicator that has been purchased for a R700-15R and have exactly the same problem, so I don't think it is hardware related.

  Any help would be greatly appreciated :-)

  Please don't get me wrong, but to me this behavious seems logical. When you close the lid internal speaker and microphone placed close to the cam are blocked so I don't know how you want to use.
  When the laptop is closed and set aside, it's almost the same as the office. All devices that you need should be connected to the docking station and external devices.

  If you use your laptop on a regular route, but they also appear external to office extension, you can use all the internal devices to your laptop.

  In my opinion the point of berthing of the use of the station of different devices to your laptop, but using the docking station, you can remove the laptop and take it with you without disconnection of all connected devices, including the power supply.

  To be honest, I see here no problem. You can contact Toshiba service nearest and ask for opinions, but I'm sure the answer will be the same.

• Portege R830-10R: No. USB connection after recovery from sleep mode

  Nice day!

  I have experienced the problem depending on my Portege R830-10R for a long time.

  Quite often, when he recovers as soon as "sleep" mode it loses the ability to recognize USB devices and built-in 3G modem does not work as well.

  After awhile, like 10-15 minutes of work (or), the problem is solved by itself, but normally, it is not the case.

  If I try to send the laptop to Hibernate or "standby mode" again, while this problem is active, allows to say, it not put into hibernation and crashes on a midway with a black screen - so I have to stop it manually, and then start again.

  Normally, the only way to solve the problem is to restart, but the issue comes after the next "standby".

  Someone has something like this? Any solution available?

  Hello

  > Quite frequently, when he recovers as soon as "sleep" mode it loses the ability to recognize USB devices and built-in 3G modem does not work as well.

  Have you noticed this behavior from the first day of purchase?

  Only special USB devices assigned as USB flash memory stick or USB HDD or are
  other devices such as the USB mouse or USB keyboard has also affected?

• Portege R830 - updates BIOS and USB 3

  Hi all

  I have a Toshiba Portege R830, business management Windows 7 (SP1) 32-bit (for work).
  I also start Linux Mint 14 64-bit, that I installed it on a portable USB HDD (non-professional).

  I recently bought a 3 USB HARD drive, but when I connect it to the USB 3 port on my R830, it gives me only USB 2 speeds (25 MB/s).

  I checked with some diagnostic utilities (usbdeview, etc.), who say that the drive is connected in USB 2.1 mode.

  The drive reports itself as being 3 USB, cable is USB 3 (SuperSpeed) and the port that I use on the R830 is 3.

  I feel the same way, if I boot on windows or linux.

  I've updated all the drivers on the two operating systems, does not.

  then I tried to update the BIOS, but I get the following error:
  "An error occurred during the preparation of the updated environment.
  You have not given the permission to execute the update".

  For the record, it's the BIOS I'm leaving, & to.
  BIOS version: Current Ver.2.80--> updated Ver.4.10
  THIS Version: Current Ver.1.10--> update Ver.1.60

  Does anyone know why I wouldn't get USB 3 speed (which, for my drive, are expected to be around 40-50 MB/s), or why all the diagnostics say USB 2?

  Does anyone know how to overcome the problem of updating the BIOS?
  (I tried in safe mode, disable AV, disabling NX)

  See you soon

  This USB driver is installed?

  Please try to install it and check again speed USB.

• Re: Portege R830 - cannot find my model on the list of Product Support

  Hello world

  I recently bought a Portege R830 and was trying to find support for my model page.

  However, on the list of Product Support, where you choose the model, I can't find which is mine.

  My model is displayed as * R830-1056UB * in the box your laptop came and he just say * Portégé R830 * on the underside of the laptop.

  There are several entries for R830 on product support list, but * R830-1056UB * is not one of them.

  * Any ideas how I can decide which one is mine? * (I'm worried about download bad software/drivers for my laptop)

  I'm not in a country with a support phone number and it seems Toshiba support do not have a contact e-mail, so I was not able to contact Toshiba directly for help.

  Thanks in advance for your time and help!

  RG

  Hello

  I put t know that Toshiba support page that you have controlled, but if this laptop is designed for the Asian market, you should find it on the support Toshiba Asia page.

  In which country did you buy?

• Some function keys do not work on my Portege R830

  Like others, I have a new Portege R830 and experience the sudden and unexplained feature of keys loss 13 function. My os is 64-bit native windows 7 with office 2010 installed subsequently. I have the SSD model.

  I followed the instructions, withdrawal PVAT and re-setup, and I have two VAP and operational flashcards. I used the drivers of the USA site for the last series (Australian and European pilot sets are old and different versions).

  In most, but not all, function keys are working again. What does work are the following:
  -Functionkey F12 does not
  -volume up and down keys not working not - what I'm more interested - suggestions on how to make functional again please?

  also, on re - install VAP, I lost the feature on ecobutton. Suggestions on how make it work again?

  Thank you in anticipation

  Hello

  You are on the guy to the right way of the VAP and utility Card Support Flash controls the FN keys. If you have a European model for laptop, I advise to use the drivers of Toshiba page of European pilot, but generally avoid a difference in software

  However, in my case restart the cards Flash allows you to recover the functionality of buttons FN. Can be found in all programs-> Toshiba-> Flash, Flash cards cards.
  In order to verify if restart help.

  Regarding the key Eco: ECO Utility controls this button too then recommend installation/reinstallation of the software next to the VAP

• Portege R830 - ConfigFree bug at startup

  Good afternoon

  I use a Toshiba Portege R830 (PT321E), our operating system is Windows 7 x 64. We found ConfigFree to create network profile.

  We have created a profile to altern Wired/Wireless connection when plug/unplug the wire.

  We note that at the start, after connection, we have an error message:

  ConfigFree «»

  The following may be responsible for the failure.
  Wireless LAN Utility is active (Please close the utility).
  Netwok property window is open (Please close the window).
  Internet windows option is open (Please close the options window).

  In cases where there is always a problem, please close all other applications and then run ConfigFree"

  So we are starting and no one should be started except Wireless LAN Utility can be started (I don't know how to check).

  You have an idea?

  Hello

  Try to configure the profile once more.
  If this does not work, uninstall the ConfigFree.
  Download the new version of the page of the Toshiba UE driver and install.
  Then try to set it up again.