read the serial port PIN +.

Similar Questions

• Sometimes the lost bytes, reading the serial port

  Hello!

  I'm reading the serial port data (flow rate 57600 baud rate) that works very reliable so that I do not open any other window

  or minimize/restore my window of the application during the program is running. Then a byte of incoming data will be lost.

  I get a string of 30 bytes each 50 m in most of the cases the first byte is lost, sometimes one in the middle.

  This occurs not only on a PC.

  Is this a problem of LabVIEW or Windows?

  Are there settings that can solve the problem?

  Best regards

  JK78

  I solved the problem.  

  There was a bug in my program who become visible only if a window has been reduced or restored.

  When there are two or more messages in the buffer VISA, the separation of the messages was incorrect.

  Array index corresponded to false so that the first byte of the second message was at the end of the first

  and so the second message in the buffer seemed incomplete.

  In normal operation, the playback loop runs so fast, never both messages are in the buffer.

  Thanks for all replies.

  JK78

  Either way, I work with LabVIEW 2009 and serial interface hardware motherboard. With XON/XOFF flow control

  is not possible in my application because all the hex values from 00 h to FFh may appear in a message.

• Read the Serial Port in case of break in series

  Hello world

  I want to create a VI who will write a series, write interruption, then wait for an interrupt series to be received and if it is received, read what's on the serial port.  However I can't the VI to detect that an interruption of the series took place.  I looked at and followed what was done in the "Detect the Event.vi Break" example in examples of Labview.  The microphone that speaks to the VI sends a break of 13 bits (approximately length 57us), as expected, proved by the use of an oscilloscope but Labview is not contagious. I have attached the VI in question.  It is used as a subvi in a larger program.  I'm missing something or doing something wrong?

  I do not know.  230 400 is a very fast pace.  The UART in the PC isn't really in the game, but the EasySync USB/serial box is what is the factor.  USB is part of the communication may be adding a few complications.  You may browse the EasySync detailed technical data to see if they talk about it.

  I would certainly try a very long break first.  If it works, then start working backwards to small jumps.  If a long pause does not work, then you know that perhaps the problem is elsewhere.

• Can not read the serial port VISA without MAX

  Hello

  I'm trying to build an application that will interface with a Black Cat Systems GM-10 radiation detector.

  The app works fine on my computer (with the full development system OR) but when I install it on another computer, without LabView, the application cannot see the serial port!

  I checked that the driver is installed correctl and Windows can see the device, but when I run my program, he can't seem to access the serial ports.

  I then tried to install MAX on the second computer, how the application worked well, but as I install this app in other places, I don't really have the ability to install MAX everywhere (software must be autonomous).

  Any help would be appreciated!

  Z

  I would have joined the project file, but the forums seem to not want to allow me to download that big of a file.

  What version of LabVIEW are you using? With 8.x, the installer is very able to install the runtime of NI-VISA and MAX. If you are using an older version of LabVIEW, there is an option to include the series VISA support. Install just MAX will do nothing to make the available ports. This is the VISA that does this.

• read the serial port management using the SRM Protocol

  Hello

  I have a gas analyzer that communicates with the PC via the serial port.

  This is the "Industrial VarioPlus SRM".

  I have attached a PDF file that describes the communication protocol.

  I'm trying to decode the data that are sent from the parser, but I can't do it.

  I have attached the vi in which I made some effort.

  Any help is appreciated, at least for a single value in the data stream.

  Thank you.

  
  

• Read the Serial Port with termination Char?

  Hi, I have a particular piece of hardware that I'm communicating which sends a stop character 0xAh at the end of the data written to the port. I have trouble reading the data from the port where I only get half of the data due to synchronization problems. I know that it's related to be looking at the bytes to the port property node and read the bytes that probably replacing end setting tank. I have the correctly defined termination char, so, how did a survey for serial data to the port without using the bytes to the port method because I don't think that it works when you use the termination char port method. Anyone know this issue?

  Simple VI that explains what my main VI by defining the term tank and using the bytes to the method of port that is not working properly and causes problems of loss of data from mark is attached.

  Thank you.

  
  

• [begineer] reboot a 'while' loop reading the serial port

  Hello! I read some data from a COM port. I want to read my like this "%d S. the unit will send data continuously and depending on when I push the button run in labview, it can start to read data from the middle (%d is a four-digit number). as: 23 S 15'

  "whenever the first character of my data is not of", I need to restart playback. I read the data in a while loop. so I need to stop the while loop. From what I found on the internet, I used a case, another while loop and shift registers.

  but in some way I'm stuck inside the while loop. My VI is attached. Thanks in advance and sorry if my code is a mess!

  PS: what should I do if the bytes I get to the port is variable? use bytes to the port?

  The device sends a character at the end of the line at the end of each message?  You are currently Setup to do this by activating the stop character (currently set to end of line/10/0xA).  If this is true, then simply set the bytes to be read on the VISA to read something rediculously high.  It will stop playback when it finds this termination character.  From there, you just have to check for the correct format.  If this isn't the right format, ignore him.  Otherwise make your recording.

  I managed to clean up your code a bit on this basis.

• Parity errors & read on Serial Port framing

  Hello, I am writing a program that reads the serial port IR thermometer. Intermittently I get parity so many framing errors and can't explain why or find a way to remedy. All the parameters of the series were double checked and controlled. I don't get any errors when you use HyperTerminal yet, when I do test bed in MAX, I see these mistakes from time to time. I tried the suggestions of the knowledge base for these as presenting a delay between the Visa set up and read the Visa or flushing buffer issue before reading, but none worked. Any idea or ideas would be appreciated.

  In addition, while searching through discussions on parity and framing errors, I saw a when a user recommends the following: "use wait event triggered by the stop character and when the error occurs, I just deleted the error, empty the buffer (wait the next stop character) and reread." If that sounds like a good solution, how would I go about its implementation?

  I've attached a screenshot of my reading series loop so you can see what I'm doing. I do about the error code control timeout is.

  Given that you have activated the stop character, you should not use the bytes to the serial port. You shouldn't have to delay or any function buffer flush.

  PS, You also have to change the way your loop exits.

• How use the serial port read and display the text but not scroll off the screen?

  I'm new-ish/return user fan of Labview and trying to change the example VI "Advanced serial write and read VI" is the part of the dev suite 2012.  I need to use the string box for ALL of the text from a serial port, always adding and just roll off the screen when the actuals come to the serial port.

  What actually arrived more than bytes (or no bytes AT ALL!), during reading time text, current rolls out of the box in the chain.  Even when receiving 0 bytes, screen is removed.  I'm not very familiar with the locations of functions and even worse to understand obscure references to functions, so please keep very basic answers so I can follow.

  Just to be clear, I need window of the chain behave as HyperTerminal does always displays the data and it is not pushed by window arbitrarily.

  Thank you

  Steve

  A long shot.

  Is that what you want?

• Using the Serial Port on the HP 50 g graphic calculator

  Hello world

  I have another question. I want to use the Serial Port on the HP 50 g to connect with another device. The device is called the MFJ-1214PC. What it does is to accept the text and commands through a 9-pin serial Port and converts the text in a Code Morse/RTTY sound audible. It also decodes Audible the Morse Code and RTTY radio signals and displays them as text on your computer. The program that controls the MFJ-1214PC was originally written for an IBM PC for the MS-DOS operating system. The HP 50 g graphic calculator meets the system requirements for the simplest version of the program. I was wondering if there is an MS-DOS emulator written for the HP 50 g, which would allow the HP 50 g to become the computer in this case, or if the program could be rewritten and brought to the HP 50 g. If it could be rewritten, programming language what do you think would be better suited to this type of application (if it is even possible?) or UserRPL, SystemRPL or Assembly. Don't forget that I'm a complete newbie with the HP50g and have never programmed with it yet. I'll include the manual of the MFJ-1214 PC as an attachment so that you won't have to look for him. Thank you in advance for your help!

  ~ Zekelegge ~.

  I understand (from my brief overview) out of the box-MFJ-1214PC, this offer box decoder output series computer.  The computer (50g in your case) will have the software to read message series and then convert that to an output for display.

  BartDb gave you the right answer.

  A serial cable with the correct speed level and reversing lever to manage as well as the 50G has a RS-232 signal to the outside world is the ideal solution.

  However, make sure that the output of the decoder box series package can be understood by the 50 g. aud, bits, etc.   (you have the set-top box manual, so you'll have to look that up)

  the streamsmart is not an aggregator of serial port.

  in other words, these connectors DIN of Qty 4 on the front do not accept series rs-232 input and send then to 50 G.

  I'm not an expert, streamsmart more info on these boxes is rare to find.  The probes are even more rare.

  However, I know that the 4 connectors are for the analog-to-digital conversion in the probes.  The streamsmart works as a "data logger" in which he sees the input probe, the A/D converted, then sends it to the 50G (or a computer via the USB port).

  In addition to the solution of Bart, there was another named Tiwag forum poster who created a serial cable and displayed a schematic representation of the cable.  This information can be found here:

  https://groups.Google.com/Forum/?fromgroups#! searchIn/comp.sys.HP48/serial$20port/comp.sys.HP48/ltcane1jSOw/uHyw2Ti03kgJ

  to see an example of programming to use the serial port of 50G, you can reference the following hpcalc GPS data collection program.

  http://www.HPCalc.org/details.php?id=7105

  It is written in userrpl so can be crossed with the reference of users advanced for the translation of the syntax.

  It seems that the main routine of concern for the comm to the gps is in the file "GPS >.

• How to read the Serial Arduino data using labview VISA?

  Hi =). Im a beginner work reading data series from an arduino but im facing... Lets do it step by step

  I built a voltage divider circuit which gives from output
  from 0 to 5V. The output of this circuit is sent to a 0 analog input pin
  of a Committee of Arduino Duemilanove.

  (1) Firstly, I connected the cable to connect to my laptop USB the Arduino.

  (2) I went to start-> control
  Control Panel-> system-> hardware-> Device Manager. Check the Ports (COM
  & LPT). In my laptop I can see USB Serial Port (COM4). Now I know only in
  LabVIEW that I must read the data series COM 4.

  (3) to the side of the arduino, here's the code to read changes in voltage
  entered to analog pin 0. The last line of 'delay' determines the sampling
  Rate of how we want to taste the output of the voltage divider:

  int potPin = 0;    Select the input pin for the output of the voltage divider
  int val = 0;       variable to store the value from the probe

  void setup()
  {
  Serial.begin(9600) (9600);    Opens the serial port, establishes the rate of 9600 bps data
  }

  void loop() {}
  Val = analogRead (potPin); read the value of the voltage divider
  Serial.println (Val);
  Delay (10);
  }

  I slightly modified the basis series reading writing VI... I have
  attached the block schema used with comments. Basically, I tried to read
  data series, divide by 1023 and multiply by 5 to graphic voltage
  variations of the voltage divider circuit.  But Im not getting
  the correct voltage output values. The value of the tension just keeps go
  0 and coming again, as shown in the photo.

  Could you guys please guide me on what went wrong?

  Thank you!

  -you read the data, even if there is no data on the port. If 0 bytes are read => «»

  -in the case of false, you resources VISA wired for the output of channel tunnel?

  -There is no close VISA at the end of the VI resources

  -you're not a loop this VI reading bytes

  I added an addaption of your VI that you should give a try maybe

• Using the Serial Port for data acquisition Non-Serial

  I searched the forums and can't find anything on this topic.

  I saw that it was possible to use the parallel port for e/s digital single and I was hoping that the serial port can be configured the same. It seems all VI VISA only to use the serial port to receive ASCII characters at a given flow rate, but is it possible to simply query the status of the line series at my own speed to see if it is high or low, kind of like a single pin DAQ?

  It seems that it would be possible until the serial data are read and controlled by labview, not Windows. Let me know if you have ideas of how to approach this problem, or any comment as to why it is not possible.

  Thank you all!

  Select the property > settings series > Modem of the line parameters. For example, the State of the CTS is an entry to the pc.

  With the help of these lines is a very poor substitute for a scope or map DAQ. The only things you can return is Asserted, Unknown or Unasserted. The range of acceptable signals is important enough. Anything between + 3 and -3 is an unknown state. Your other signals is + / 3 to 15 volts. What type of signals do you really want to capture?

  Edit: there is no such thing as a visa so I have no idea of what you actually use.

• What standard corresponds to the Serial Port of the Tecra A9

  What standard corresponds to the Serial Port of the Tecra A9?
  What is RS - 232?

  All I know is that it s a serial port 9-pin

• Tecra A8: external keyboard connected to the serial port: the necessary specific configurations?

  Hello
  I want to share a monitor and an external keyboard with Tecra A8 and a desktop computer. To do this, I bought a switch 2-port Linksys where I plugged the external monitor and a keyboard. With the monitor without problem because there is a specific port for this. However my Tecra has only 3 USB ports and a serial port 6-pin where I connected (with a 6-pin Mini DIN adapter) on the keyboard. When I turn on the screen it's ok, but the keyboard (I also tried a mouse) does not work. Do I need a specific configuration on the serial port to accept the external keyboard? If so, what commands do I need on the XP operating system?
  Thank you
  Luis

  RGB (monitor) port used to connect the external monitor.
  If you want to connect the external keyboard, you have to use the USB ports.
  Additional legacy USB emulation must be enabled for the keyboard.
  These settings you can change in the Toshiba HWSetup under control panel.

  If you connect multiple devices to the switch USB (hub) Please be sure that the USB hub using external power.
  A low power USB could be a reason for the external USB device failure.

• How to periodically send various types of data via the Serial Port?

  Hello! Everyone

  I have to send data to LabVIEW to my device on the Serial Port.

  I know how to send data on serial port in LABVIEW, I already have this part.

  Now the problem is that I have several types of data I need to question my embedded device, if I want to send the query periodically command.

  So lets say that my four Op Codes are the following, which will send four different types of query command to my device on the serial port.

  (To be honest only OP_LED and OP_SENSOR is used now)

  0, OP_SYNC

  1, OP_LED

  2, OP_SENSOR

  3, OP_FUTURE

  Structure of basic package is as follows:

  Header (0x2C), Checksum, length of the data (n bytes), Op_Code (1 byte), length (length of Code + data Op)

  For OP_LED, I need to send the package as follows:

  0x2c 0x02 0x01 0 x 00 0x2F (0x2F being the XOR checksum) (calculation of Checksum part is done and SUB Vi form)

  Length of the package this is 0x02

  0x01 is Op Code for OP_LED

  In the same way

  For OP_SENSORi need to send the package as follows:

  0x2c 0x03 0x02 0x00 0 x 00 0x2D (0x2D being the XOR checksum) (calculation of Checksum part is done and SUB Vi form)

  0x03 is length of packet here

  0x02 is Op Code for OP_SENSOR

  So, how can I do this periodically in labview, in such sort that period can be adjusted whenever necessary.

  Is there something in LabVIEW to do.

  I had done the reception and decoding part and working properly.

  http://forums.NI.com/T5/LabVIEW/store-data-coming-from-serial-port-in-buffer-and-then-take/m-p/32722...

  So I must implement read and write the part of same while loop?

  Do not insert in the table if you put data in an array at index 0.  Just use array to build.

  No need to have Visa to write don't be a part of wire to the wire of reference and error VISA go in the upper part.  These wires should go THROUGH the entry VISA.

  Don't your checksum requires all the bytes up through data?  Righ now, you only put the checksum on data bytes and forget the opcode and length bytes.

  Your sending is not the opcode for Opsync or Opfuture.  You just send the empty tables.  At the same time for the other two, you put the opcode in the data table.  All your original opcode in the table build thread.  Get the data out of these structures in case item which is supposed to represent the opcode.

  xpress_embedo wrote:

  Now it works but I have now two problems.

  (1) OP_SYNC and OP_FUTURE do not data, but still receive its data on serial port, can I do something here as I have nothing when the table is empty in the structure of the case.

  I do not understand this statement.  Perhaps my answer above will fix any issue you have here.

  (2) how can selection operation Code to be send is done using control façade but real application, this task should be automated to a certain frequency, like OP_LED package must go out to the serial port to 100msec and packet OP_SENSOR must go out to 1000msec, I do this.

  Now you agree a little more architecture.  I would encapsulate the code that is in the while loop as a Subvi.  Then with the hand of your program while loop, use two time Express VI, a game for 100 msec, the other for 1000 msec.  When an express VI is true, run the Subvi with a command set waiting for the answer.  When the other VI Express is true, have it run the Subvi with the other set of commands.

  The device responds with anything when you send these commands?  You only send data.  I see no VISA Read to be able to recover all the data.