Reboot loop in Vista

Similar Questions

• Reference Dell Vista stuck in a reboot loop must restore

  I have a dell desktop computer I bought from rent a Center about 2 years ago. It comes with Windows Vista. They don't did me not a recovery disk. I had a lot of questions and restore points were not helping, so I went through f8 and fact a reset. After that she completed successfully I clicked on finish, and it began to restart, which I expected.

  Now, however, he is stuck in a reboot loop. It gets to the screen that has Dell on this, with the f2, f12 options in the right corner, and then start again again and again. I tried to press f8 and hope go in safe mode and see what was up, but f8 does not open and f2 and f12 are not help at this point. they give me boot priority and so on but no real start until now kind of options. It is possible that windows doesn't have factory loaded, and now I have simply no operating system?  They say they have a reset disk can I come down and use, but im wondering if this will help because I can't really get anywhere or if im just done...

  No messages online that I was looking for really specific my situation...

  * original title - Dell Vista Start Up start up loop *.

  Hello

  ·         Did you follow the steps in this article to restore the computer to factory settings?

  If a factory restore full does not lead to a fully functional version of Windows then you have a hardware problem. I came in contact with Dell technical support.

  Diana

  Microsoft Answers Support Engineer

  Visit our Microsoft answers feedback Forum and let us know what you think.

  If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• Computer goes into a reboot loop after installation of an update

  Original title: Windows Update on August 12, 2011

  My laptop has done a windows update this morning, don't know what he did, it was very fast now, everytime I turn on windows trying to open then fails and continues to do this in a loop.  Please no technique with the help of numpty here!

  Hello

  1. what update has the problem from occurring?

  Follow these steps and check if the problem persists.
   
  Step 1:

  
  You can check if you can "disable automatic system failure reboot " from the options in advance. In this way the computer will not go into a reboot loop and you will be able to note the error code, if any. If you see no error code, you can answer comes back with the error code.
   
  Step 2:
   
  I suggest that you start your computer in safe mode and check if the problem persists.
   
  Step 3:
   
  If the system works fine in safe mode, I suspect that there could be a conflict of software of third party causing the problem to occur. I suggest that you start your machine in a clean boot State.
   
  Note: Follow step 7 to your computer as usual.
   
  See the below article access in Event Viewer.
   
  Open event viewer
  http://Windows.Microsoft.com/en-us/Windows-Vista/open-Event-Viewer

  Step 4:

   
  Updated version has a problem in the history of the update.
   
  a. open Windows Update by clicking on the button start. In the search box, type Update, and then in the list of results, click Windows Update.
  (b) in the left pane, click view update history.
  c. to display more information about an update, double-click it.
   
  Do System Restore to the point that your computer worked very well and install updates manually ensuring that do not install the problem causing the update unless it says 'important update '.

• Windows 7 Edition Home Premium. After that windows update will in a reboot loop

  Windows 7 Edition Home Premium. After that windows update KB982926 & KB982670, will in a reboot loop, 64 bit, Dell Studio XPS. I used F8 & restore to burst. Tried the update again with the same results. Silverlight & Net Framework updates

  Hi pbmass,

  I want to clarify if you are able to start the computer on the desktop after the system restore.

  Follow the steps mentioned below and then try to install the updates manually

  Step 1: Auditor of file system (CFS) scan to fix all of the corrupted system files. To do this, follow the steps mentioned in the link below:

  How to use the System File Checker tool to fix the system files missing or corrupted on Windows Vista or Windows 7

  http://support.Microsoft.com/kb/929833

  Step 2: Run the fixit available in the link below to reset windows update components.

   

  How to reset the Windows Update components?

  http://support.Microsoft.com/kb/971058

   

  Step 3: Disable the security software; Follow the steps mentioned in the link below

  Disable antivirus software

  http://Windows.Microsoft.com/en-us/Windows-Vista/disable-antivirus-software

  Important: Activate security software once everything is done.

  Step 4: Download the update manually and then install them

  The .NET Framework 4 Client Profile is available on Windows Update

  http://support.Microsoft.com/kb/982670

  Description of the update for Silverlight:

  http://support.Microsoft.com/kb/982926

  Thank you, and in what concerns:

  Ajay K

  Microsoft Answers Support Engineer

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Reboot loop windows 7 updated

  My Windows 7 from Vista installation failed. After two-thirds of the site amenities treat the cumputer close and
  said that he would like to reinstall my old version of vista. My Dell XPS 1330 since this message is in a reboot loop.
  You have any ideas to fix this?

  alchemist108,
  Thanks for visiting the site of the community of Microsoft Windows. The question you have posted is related to Server 2008 and would be better suited to the TechNet community. Please visit the link below to find a community that will provide the support you want.
  TechNet Forum Mike - Engineer Support Microsoft Answers
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Computer is stuck in a reboot loop, while security updats

  ORIGINAL TITLE: reboot problem

  Computer is stuck in a reboot loop, while security updats

  Hello

  1 were there any hardware or software changes made on the computer before this problem?

  2. do you get an error message or an error code? If Yes, what is the exact full error message?

  I would suggest trying the following methods and check if it helps.

  Method 1: Try to run the system in safe mode restore.

  Step 1:
  Try to start the computer in safe mode, here is the link:
  http://Windows.Microsoft.com/en-us/Windows-Vista/start-your-computer-in-safe-mode

  Step 2:
  Once you start the computer in safe mode, try to perform the system restore and check that if it helps, here is the link:
  http://Windows.Microsoft.com/en-us/Windows-Vista/system-restore-frequently-asked-questions

  What are the system recovery options in Windows Vista?

  http://Windows.Microsoft.com/en-us/Windows-Vista/what-are-the-system-recovery-options-in-Windows-Vista

  If you were able to start your computer normally by using the system restore, then refer to the following method, and try to update your windows.

  Method 2: To help resolve the error and other messages, you can start Windows by using a minimal set of drivers and startup programs. This type of boot is known as a "clean boot". A clean boot helps eliminate software conflicts.

  Note When you perform a clean boot, you may temporarily lose some functionality. When you start the computer as usual, the function returns. However, you may receive the error message, or you can experience the original behavior.

  Note: follow step 7 to reset the computer to start as usual after the boot process.

  http://support.Microsoft.com/kb/929135

  See the following help link.

  Problems with installing updates

  http://Windows.Microsoft.com/en-us/Windows7/troubleshoot-problems-with-installing-updates

  Hope this information helps.

• Laptop stuck in a reboot loop

  Original title: locked cpu

  my computer laptop gateway is in a continuous reboot loop at startup.vista family premium is the operating system, automatic restore or restore to an earlier point in time not working, what a Dick I do?

  Hi Ohmer,

  1 did you recent hardware or changes to the software of the system?

  2. you receive messages or error codes?

  You can try to disable restart of the automactic on the failure of the system and look for the error.

  For more information, you can consult the following article:

  Startup options (including safe mode)

  You can also try the following steps and check if it helps.

  Method 1:

  You can try to perform a test of the last good known Configuration and check if helps solve the problem.

  Using the last good known Configuration

  Method 2:

  You can also check if the problem occurs in safe mode.

  Start your computer in safe mode

  Method 3:

  If the problem occurs in safe mode, and then try to perform a startup repair and check if it helps.

  What are the system recovery options in Windows Vista?

• 0 x 00000024 reboot loop

  I rebooted Vista recently it was very slow, and it got stuck in a continuous reboot loop. Startup Repair also fails to load correctly and restarts until I can do something with it. They showed me a BSOD with an error message after turning off the auto reboot:

  Stop: 0 x 00000024 (0 x 00190444, 0x86ec9940, 0xc0000102, 0x00000000).

  They tell me to run chkdsk, but don't know how while I can't in Vista at all.

  Safe mode is stuck at crcdisk.sys and restarts.

  Any ideas? How can I run chkdsk without going into Windows?

  Thank you

  Hello

  Check the following message methods to check the disc including making a repair disk.
  Some discs of diagnosis of the auto manufacturer to start.

  -----------------------------------------------------------------------------------------------------------------------

  Check this thread for more information using BlueScreenView, MyEventViewer and other methods to solve problems
  BlueScreens - answers top 3 (+ 1 more).

  http://social.answers.Microsoft.com/forums/en-us/vistarepair/thread/3deab2fa-4000-4136-8c78-a3d22b1db009

  ------------------------------------------------------------------------------------------------------------------------

  Alteration of the disc or the material associated with the operation of disk (hard drive, wiring and controller of the motherboard),
  lack of enough system memory, BIOS and antivirus/antispyware/security programs may have a role.

  ------------------------------------------------------------------------------------------------------------------------
  
  BCCode: 24 0 x 00000024

  Cause

  One possible cause of this bug check is damaged drive. Corruption in the system of NTFS file or defective (sectors) on the hard disk can cause this error. Corrupted drivers SCSI and IDE may also compromise the ability to read and write to the disk system, so causing the error.

  Another possible cause is the depletion of memory pool non paged. If the nonpaged memory is exhausted, this error can shut down the system. However, during the indexing process, if the amount of memory available nonpaged pool is very small, another driver in nonpaged kernel memory in pool mode may also cause this error

  Solve the problem

  To solve a problem of hard drive corruption: Check Event Viewer for error of SCSI and FASTFAT (syslog) messages or Autochk (the application log) that might help determine the device or driver that generated the error. Try disabling any antivirus software or Disk Defragmenter tools that continually monitor the system. You must also run the diagnostics of material provided by the manufacturer of the system. For more information about these procedures, see the manual of your computer. RunChkdsk /f /r to detect and resolve any file system structural corruption. You must reboot the system before the start of the analysis of disk on a system partition.

  To solve a problem of impoverishment of nonpaged memory: Add new physical memory to the computer (which increases the amount of memory available to the kernel nonpaged pool), or reduce the number of files on the volume Macintosh (SFM) Services

  Schedule chkdsk to run at next boot (checkdisk).

  How to run the check disk at startup in Vista
  http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

  BCCode: 24 0 x 00000024<-- read="" this="">
  http://www.faultwire.com/solutions-fatal_error/NTFS-file-system-0x00000024-* 1051.html? order = votes

  I hope this helps.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• Computer randomly stops and goes into a reboot loop

  Original title: computer stops randomly on its own.

  When my computer is running, it will restarts randomly.  Any suggestions on why he can do this and how can I stop doing that?  Thank you!

  Hello
   
  1. do you remember any changes on your prior approval to question that occur?
   
  In the meantime, follow these steps and check.
   
  Step 1:
  
  You can check if you can "disable automatic system failure reboot " from the options in advance. In this way the computer will not go into a reboot loop and you will be able to note the error code, if any. If you see no error code, you can answer comes back with the error code.
   
  Step 2:
   
  I suggest that you start your computer in safe mode and check if the problem persists.
   
  Step 3:
   
  If the system works fine in safe mode, I suspect that there could be a conflict of software of third party causing the problem to occur. I suggest that you start your machine in a clean boot State.
   
  Note: Follow step 7 to your computer as usual.
   
  See the below article access in Event Viewer.
   
  Open event viewer
  http://Windows.Microsoft.com/en-us/Windows-Vista/open-Event-Viewer
  
  Aziz Nadeem - Microsoft Support

  [If this post was helpful, please click the button "Vote as helpful" (green triangle). If it can help solve your problem, click on the button 'Propose as answer' or 'mark as answer '. [By proposing / marking a post as answer or useful you help others find the answer more quickly.]

• Start of loop - Windows Vista

  original title: __Start loop - Windows Vista

  Hello

  This can be a problem in two parts that I don't know if they are connected.

  The problem pc had a virus / trojan waring message last week, but Windows Defender caught the virus and I could clean up and remove from the machine (I hope).  The pc belongs to my parents, my mother bought McAvee security add to the computer as additional protection, but had not downloaded it.

  I followed the instructions of download and downloaded the program.  To restart the computer, the wireless internet connection was lost, and the system froze.  On turning off the pc, I expected to be able to start the pc through the normal request to "start windows normally".  It worked, but the pc froze again, so do the same thing again once, the following past once I have been through the process of starting - a message from the blue screen appeared with a long message from Windows startup does not but, before I could read the content of the email the pc was off.

  From this point, repair system continuously in a loop and it is not letting me open their computer.  Once he arrives, he works to try to find a problem and then can't find the problem. It is said "If you have recently attached a device to this computer, such as a camera or portable music player, remove it and restart your computer.  There is nothing connected to the computer, even if it does its not as if he's trying to run the CD player.  I tried crossing the other early screen repair option but nothing helps.

  Can anyone help?  If you can, could you please put the answer in simple language... I'm not too good at dealing with the 'courage' of the pc is so I'm easily confused by the jargon and techno speak!

  Thank you and look forward to hear from you.

  You should never have AN antivirus installed.

  More than one can cause system outages.

  The original AV been uninstalled before installing McAfee?

  Follow these steps to try to solve your problems of boot.

   

  Restore point:

  http://www.howtogeek.com/HOWTO/Windows-Vista/using-Windows-Vista-system-restore/

  Do Safe Mode system restore, if it is impossible to do in Normal Mode.

  Try typing F8 at startup and in the list of Boot selections, select Mode safe using ARROW top to go there > and then press ENTER.

  Try a restore of the system once, to choose a Restore Point prior to your problem...

  Click Start > programs > Accessories > system tools > system restore > choose another time > next > etc.

  http://www.windowsvistauserguide.com/system_restore.htm

  Read the above for a very good graph shows how backward more than 5 days in the System Restore Points by checking the correct box.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

   

  If restore work not and you do not have a Vista DVD from Microsoft, do a repair disc to do a Startup Repair:

  Download the ISO on the link provided and make a record of repair time it starts.

  Go to your Bios/Setup, or the Boot Menu at startup and change the Boot order to make the DVD/CD drive 1st in the boot order, then reboot with the disk in the drive.

  At the startup/power on you should see at the bottom of the screen either F2 or DELETE, go to Setup/Bios or F12 for the Boot Menu.

  When you have changed that, insert the Bootable disk you did in the drive and reboot.

  http://www.bleepingcomputer.com/tutorials/tutorial148.html

  Link above shows what the process looks like and a manual, it load the repair options.

  NeoSmart containing the content of the Windows Vista DVD 'Recovery Centre', as we refer to him. It cannot be used to install or reinstall Windows Vista, and is just a Windows PE interface to recovering your PC. Technically, we could re-create this installation with downloadable media media freely from Microsoft (namely the Microsoft WAIK, several gigabyte download); but it is pretty darn decent of Microsoft to present Windows users who might not be able to create such a thing on their own.

  Read all the info on the website on how to create and use:

  http://NeoSmart.net/blog/2008/Windows-Vista-recovery-disc-download/

  ISO Burner:http://www.snapfiles.com/get/active-isoburner.html

  It's a very good Vista startup repair disk.

  You can do a system restart tool, system, etc it restore.

  It is NOT a disc of resettlement.

  And the 32-bit is what normally comes on a computer, unless 64-bit.

  See you soon.

  Mick Murphy - Microsoft partner

• The update of Windows 10 1511 reboot loop Bootcamp BSOD ACPI. SYS

  It is a copy of my thread to http://answers.microsoft.com/en-us/windows/forum/windows_10-performance/windows-10-update-1511-reboot-loop-bootcamp/8653... as I was asked to post here by the Microsoft Support Engineer.

  Hello

  Friday night, I went to bed with a working machine. I had a late 2013 Mac Pro BootCamp running with a Windows 10 Pro installed, the Build version before 1511.

  On Saturday morning, I woke up to my PC restart itself over and over again. It seems that Windows Update has decided to put a new version of Windows 10 on my machine without my knowledge. I discovered this after restoring an acronis backup (which took a few hours because of the number of incremental backups)

  Occasionally (about 1 in 20 restarts) it would blue screen with an error:

  SYSTEM_THREAD_EXCEPTION_NOT_HANDLED (ACPI.sys)

  But the rest of the time he would just start, flash a window for a millisecond that says (I think) winlaunch.exe, then restart.

  I tried a lot of things to sort it, including:

  (1) restore from a backup, acronis to Friday morning, running sfc/scannow, and then runs the update

  (2) the creation of a recovery USB, enter the console, change the boot to legacy method, so I can F8, then goes into all security modes and mode of illegal product, but I can find where windows 10 now puts the boot log

  (3) restored from acronis, switched to mac, created a new bootcamp drivers usb, switched to windows and run the option 'fix drivers' before performing the update.

  Ntbtlog.txt is not anywhere on the partition. I ran a dir /s > a.txt then open this a.txt in Notepad and searched him.

  I don't know where to go from here. I can acronis restore of a windows 10 work machine the morning before installing mandatory 1511. I don't know how to delay the update no more, I noted during a restore I had delay on updates that are why it has arisen just now.

  I do not know how to find where this BSOD ACPI.sys will come (even if it happens so rarely) or this that its trying to load just before it crashes (so I can try to delete the driver etc. by the front restored windows to upgrade)

  I guess the widowed causes 10 to do a restore, then the restore fails.

  Overall, I get at the end of my wits with this, to go a completely Windows 10 installation work Friday to more than two wasted days, restore backups, try again, rinse and repeat. It's now Monday morning and I am posting this as a ditch last attempt to solve the problem, your help would be appreciated.

  If you need more information please let me know the location of the files, etc, or their names and I will do my best to have copies available for you.

  I will now restore the backup again, uninstall loading of drivers, and then try the update of windows for the 4th or 5th time.

  Thanks in advance,

  Julian

  Woo Hoo, I've solved the problem!

  I uninstalled the drivers of graphics from AMD (with AMD Driver Cleaner) and Arcronis True Image Home 2013 at the same time, then let Windows Update run its course. Now I have a machine with Windows Version 1511 10!

  It took me 4 days of downtime...

  I hope this helps someone else.

• Stucks L50 - A satellite in reboot loop

  My L50 - A Satellite is stuck in a reboot loop. I put the computer off and drained the battery.

  Whenever I have it plug in I see the opening screen Toshiba (with no invitation to press F2 to pass set up) then it goes back to the reboot screen.

  I tried via a recovery bootable on USB but t does not work.

  What is there to do?

  > I tried to use on a USB key bootable recovery but t does not work.

  I assume you tried to reinstall the original recovery image. It should work.

  Enter the BIOS and set it to default settings. After that restart your computer and press F12. Choose the USB device as the boot device and try to restart recovery image installation.

• Y700 m2 upgrade - continuous reboot loop cycle?

  Hi all

  I recently bought a Y700 laptop with a 128 GB m2 and 1 TB hard drive.

  I found that the 128 GB drive is just about acceptable, but as I do photography editing, the drive working essentially consumes the rest 30 GB I have free instantly. I would also like a little more room for manoeuvre for failing to manage the storage space so closely.

  So I bought the following:

  Samsung SM951 M.2 PCIe SSD 512 GB
  SM951 Series MZHPV512HDGL-00000
  Capacity - 512 GB

  I read NVMe version is not supported, but I assumed it would work.

  I tried to use Acronis True Image clone/backup the existing drive, actually a recovery disc and used to restore the backup to the new drive. So far, everything seems to work.

  However, after reboot, first of all, I got a BSOD message saying "Inaccessible_boot_device" and then the system reboots. At this point the loop starts, the screen shows the text "LENOVO" on black for about 10 seconds, switches and 2 seconds later goes on to repeat the process to infinity.

  Thinking it was a problem with Acronis, I tried to use the Installation of Windows Media disc for just fresh install windows on the disk. Once again, everything seems to work and has been installed properly. However once the installation has been completed, once again reboot loop began.

  I must add that when the loop runs, hitting F2 or any other key does not work, so I can't access the bios to tell the computer to boot from a key USB etc. To exit the loop, I have to power off the laptop and remove the offending SSD drive and then restart. At this stage F2 works, allow me in the BIOS to re - assign the USB as a boot priority to try to restore media etc.

  I also tried to do "repair Windows startup", but after a few minutes, the repair process said that he could not repair the drive.

  At this point, I wonder which of the following occurs:

  1 drive is defective

  2 - the drive is not compatible (material)

  3. drive is incompatible because of outdated drivers (the laptop is 1 month old)

  Any help you offer is appreciated, because I doubt now, I can return the drive given the way it has been used now!

  An apparent difficulty has been to change the UEFI boot to legacy mode, but I kept the UEFI as first priority in the boot sequence. Things seem to work fine now.

  Weird that the 128 GB m2 player provided by Lenovo was beautiful on UEFI, yet my 512 GB there is no work?

• T440s Windows 10 Realtek Audio reboot loop

  Have downloaded the latest driver audio realtek 10 Windows on lenovo and site when you install the driver that there is a message like

  "the driver installation is a process of the 2 step, 1) uninstall the current driver and restart 2) installation of the new driver.

  The works of uninstall and reboot happens, but after that start again the new driver won't install-, instead, the exact same window appears on uninstallation, to an endless reboot loop.

  All the patches?

  OK I seem to have installed now.

  Two drivers are available for download on the page drivers lenovo, I installed the one older followed by the most recent and that worked.

• Problem in reboot loop after updates.

  I have windows XP on an Asus A8V-E-SE motherboard has developed a problem in reboot loop after updates.  It will not go in safe mode either.  Stop at a display of the driver.  I used the recovery console using the XP cd and you can see the update directories in the systemroot folder.  I followed the instructions in the forum to uninstall every update by accessing commands back to the subdirectory spuninst update and then run "Batch spuninst.txt.  I get a bunch of 'access denied' messages for each of them (varies in amount of "access denied" messages by everyone but consistent for each.)  It's not like the batch uninstall for the update does not work.  I tried to uninstall all updates yesterday 10/02/10 (I had 10) even with the "access denied" messages, but it still will not initialize properly.  No way to move the access denied message?

  See the RESPONSE (by Kevin Hau) message in this thread: http://social.answers.microsoft.com/Forums/en-US/vistawu/thread/73cea559-ebbd-4274-96bc-e292b69f2fd1

  Visit the Microsoft Solution Center and antivirus security for resources and tools to keep your PC safe and healthy. If you have problems with the installation of the update itself, visit the Microsoft Update Support for resources and tools to keep your PC updated with the latest updates.

  ~ Robear Dyer (PA Bear) ~ MS MVP (that is to say, mail, security, Windows & Update Services) since 2002 ~ WARNING: MS MVPs represent or work for Microsoft