Records Windows Vista are all attribute read-only setting

Similar Questions

• Windows XP Home deselection of read-only on the FlexNet Adobe folder do not stick.

  I have Adobe Creative Suite 3 and all programs except for InDesign. It comes up with an error message that says license has stopped working. Adobe lists several solutions, all that I tried with one exception that I couldn't because a step said to uncheck the read-only option for one of its folders named FlexNet. However, when I do this it deselects but it does not stick, if I look back at it now read-only is enabled. On a side note, in the same solution for XP Home it also says to disable Simple file sharing which is right impossible?

  Yes, the Adobe instructions sound as if they are not familiar with Windows XP Home Edition. First of all, the read-only attribute is not applicable to records in any version of Windows - XP, Vista or Windows 7. That's why you see the behavior you are reporting. And as you point out, you cannot disable Simple file sharing in XP Home. In all cases, the Simple file sharing (which controls how a computer connects to other computers in the Local network) is likely to have something to do with InDesign does not.

  I'm sorry that I'm unable to help you with this issue of Adobe, however. I guess you have uninstalled/reinstalled the program? If this isn't the case, you should try it. You may find an answer by posting in the InDesign user forum:

  http://forums.Adobe.com/community/InDesign

  MS - MVP - Elephant Boy computers - don't panic!

• cannot deactivate an attribute read-only on a folder

  Hello

  I have a folder with the read-only attribute marked with a blue square and tagged (applies only to files in the folder).

  When I try to delete it, he's going right through to the subfolders and files, but ultimately the blue square is always there.

  I am the owner of the folder and have full permission.

  I also tried with the attrib command, but that has not changed anything.

  Thanks for any help.

  Stefano

  Hi stefca,

  By default, the attributes: read-only (applies only to files and folders) will be there. Although the subfolders in the main folder would have access to read and write.

  Also if you want to remove the permission to read the file, then you must change the permissions. Follow the steps for the same:

  i. right click on the folder

  II. Select Properties

  III. Select Security tab.

  IV. click on edit

  v. check the Deny option to read.

  VI. click on apply, and then click OK

  You can see the below links for more information about the same: http://windows.microsoft.com/en-us/Windows7/What-are-permissions

   

  http://Windows.Microsoft.com/en-us/Windows7/what-to-know-before-applying-permissions-to-a-file-or-folder

  With regard to:

  Samhrutha G S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• How can I change the attributes read-only or system files?

  How can I change the attributes read-only or system files?

  To view or to remove the read-only or system attributes, use the Attrib command at a command prompt:

  1. click the Start button, type cmd in the search box and press ENTER.

  2. to view the syntax for the Attrib command, Type attrib------? at the command prompt.

  WARNING: If you remove the read-only or a file system attribute, it may seem like a regular folder and some customizations may be lost. For example, Windows customizes the Fonts folder and provides a special folder view that allows you to hide variations, such as bold and italics. It also allows you to change the display settings of the file in a way that is specific to fonts. If you remove the read-only attributes and the Fonts folder system, these custom display settings not available. For folders that you have customized by using the tab, customize the folder properties dialog box, the folder icon and other other customizations may be lost when you remove the read-only attribute.

  If a program cannot save files to a folder with read-only, such as My Documents, change the read-only to the system attribute by using the Attrib command at a command prompt.

  To remove the read-only attribute and to set the system attribute, use the following command:

  attrib - r + s drive:------------.

  For example, to remove the read-only attribute and set the attribute to system for the C:\Test folder, use the following command: attrib - r + s c:\test

  Be aware that some programs may not work correctly with folders for which the read-only attribute and the system attribute are granted. You can use the following command to remove these attributes:

  attrib - r-s c:\test

• Thunderbird 38.2 n Lightning: after restarting TB same calendar are trusquinées - read-only - unlocked n those work synchronize well n change my changes

  TB 38.2.0 Ln 4.0.2
  (1) after you restart TB same calendars are trusquinées - read-only - unlocked.
  (2) calendars, which are always announced don't synchronize well n change my changes (e.g.: if I change a n movement event title there from today to 2 days when I opened TB events is placed again in n today I lose the title changes!).
  Are other users havin same problem? Looks like this.
  Waiting for an answer, cordially.

  Update to Version 38.3.0 solved your problem?

• Using windows Vista, I can't read a jpeg photo CD.

  Using windows Vista, I can't read a CD of photos jpeg, on another PC with XP, I can read the CD. Is that what I can do to get Vista to read a jpeg photo CD. The CD was created by Boot.

  Hello
   
  1. what application you use to read jpeg from the CD images?
   
  2 - is the CD is detected in CD-ROM/DVD-ROM?
   
  3 have you tried with another CD? The other CD's get detected?
   
  You can view the articles below and check out them if you're having similar problems.
   
  When you insert a CD or a DVD, Windows Vista may not recognize the disc
   
  The CD drive or the DVD drive does not work as expected on a computer that you upgraded to Windows Vista
   
  Please answer these questions to help us better.
   
  Aziz Nadeem - Microsoft Support

  [If this post was helpful, please click the button "Vote as helpful" (green triangle). If it can help solve your problem, click on the button 'Propose as answer' or 'mark as answer '. [By proposing / marking a post as answer or useful you help others find the answer more quickly.]

• Windows Vista Step By Step-reading error in downloading the files.

  Windows Vista Step By Step-reading error in download of files do I need to talk to or call? by following the instructions in the book - I get the error in the charge process down. I buoght the book with the CD to learn and I can not even begin to learn!

  Hello Enrico Cassin,.

  There is a section of the book which should be able to help with the CD that came with the book. If you look at the Table of contents, there is a section called using the CD of the book. See the section to see if they can help you.

  What kind of error do you get when you download the file?
  Did you choose to save the files on your computer, or you chose run?

  You can also contact MSPress for a replacement CD if the CD is damaged.
  Contact telephone Microsoft Press customer service: (800) MSPRESS or (800) 677-7377

  Please give more details as to what is happening and we will try to help.

  Sincerely.

  Marilyn
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think

• All records showing the attribute read-only - cannot be changed via a Properties dialog box OR the command "attrib" user profile AND is not corrupted

  I use Win 7 64 and recently all my files have begun to show read-only. Other responses on this forum, which suggests to change the read-only via the Properties dialog box, attrib command did not work. In addition, I created a new administrator account as suggested by another answer, but the problem persists on both accounts.

  Several programs will not work now that they can not write files in folders.

  What can I do to fix this?

  Hello

  See the following article for a description of this problem.

  326549 You cannot view or change the read-only or the attributes of system files in Windows Server 2003, Windows XP, Windows Vista or Windows 7

  I hope this helps.

  Thank you for using Windows 7

  Ronnie Vernon MVP

• New folders and briefcasesall my folder are locked on read-only I uncheck and hit appl and ok but it stays still on no read.

  all my files are locked on read that I unchecked it and click on apply and ok but it still remains on read-only. I t doesn't turn off read-only. S o I can not update all the files.

  Hello

  · You are the administrator of the computer?

  · Do you remember any changes made on the computer before the show?

  Try the steps listed in the links below and check, if it would help: you cannot view or change the read-only or the attributes of system files in Windows Server 2003, Windows XP, Windows Vista or Windows 7: http://support.microsoft.com/kb/326549

  How to set, view, change, or remove special permissions for files and folders in Windows XP: http://support.microsoft.com/kb/308419

• disarm read only of invalid property - all mean read only files

  Windows Vista Home premium, I reorganized some folders between 2 users (mother and daughter) and now all files and folders appear to be read-only and I can save is no longer with applications Ms. Also when I right click to change permissions... it seems to apply to all files and folders, but after has been taken, no effect.

  just to add effect... my virus Trojan virus program does find and puts the files in quarantine a few per day I delete... I think it's just part of the environment...
  Thank you

  The reading box only file says that for an indefinite period. It's a tri-state checkbox. Read has no effect on the behavior of a file that records cannot be read-only. The box does not read only bit on a file.

• Windows Vista - unidentified network Local Access only tried everything please help

  Hello

  I have an Acer Aspire M1610 running Windows Vista Home Premium Service Pack 2 and 2 days ago when I turned it on the internet was not working and it says unidentified network Local access only. I use a wired Ethernet connection. I don't know how it happened as before I had used the computer as usual and the Internet worked very well. I did a lot of research and read a few forum posts about this problem and tried a few solutions but non of them worked. I tried the following:
  (1) disable my firewall and anti-virus who didn't work, I turned their back on immediately.

  2) press Ctrl-Shift-Enter keyboard shortcut to run a command as administrator prompt.  Allow the elevation.

  Type route delete 0.0.0.0 press ENTER.

  Type ipconfig/flushdns press enter

  Restart your computer.

  (3) the internet protocol version 6 clear, disable and enable the thing

  (4) if same Norton software removal tool I had uninstalled the when I got the computer I read that uninstall it by using uninstall windows is not entirely remove it.

  (5) another thing in the command prompt I don't remember exactly what it was, and I can't find the site Web is because I looked so much of.

  (6) I even reset my computer to factory settings and then uninstalled all unnecessary software and trials that come with and used the software again Norton removal tool.

  Does anyone know how to fix this? Any response will be greatly appreciated.

  Thank you

  Hi Alex,

  Have you tried to assign the IP addresses manually?

  I wish that refer you to this article-

  http://support.Microsoft.com/kb/928233/en-us

  Note: Important This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs.

  Back up the registry - http://windows.microsoft.com/en-US/windows-vista/Back-up-the-registry

  Thank you.

• Start Windows vista, nothing on the screen, only the pointer of the mouse

  I have a gateway desktop vista, nothing on the screen, only the pointer of the mouse
  I used the recovery tools nothing fixs

  Hello

  "I used the recovery tools nothing fixs.

  It helps us if you tell us what they were.

  Here is the guide to repair Options using a Vista DVD from Microsoft.

  If a friend or a work acquantance of yours has one, you can borrow and use it for repairs.

  http://www.bleepingcomputer.com/tutorials/repair-Windows-with-Windows-Startup-Repair/

  Table of contents

  1. Overview of Windows Vista repair options
  2. How to perform an automatic repair of Windows Vista using Startup Repair
  3. Advanced Tools Overview
  4. Conclusion

  If you do not or can not borrow a Microsoft DVD there is a download of a file ISO of Vista Startup Repair available that you can put on a Bootable floppy to make the above startup repair and that the method is recommended by a large number of posters in these Forums.

  Unfortunately, you have to buy it.

  Here is a link to it:

  http://NeoSmart.net/blog/2011/Windows-Recovery-discs-updated-reinstated/

  @@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@

  If necessary, here's how to reinstall back to new condition.

  "Gateway Recovery Center in Windows Vista® '

  http://support.gateway.com/s/software/MICROSOF/Vista/7515418/7515418asi.shtml

  Read these options to the gateway address:

  Gateway System Recovery from the hard - the following are methods to recover or repair the computer using the recovery of hard drive partition.

  • Complete recovery plant
  • Restoration with automatic data backup
  • Windows recovery environment

  See you soon.

• Cannot change attributes read-only files, by updating the drivers help Driver Whiz from HP.

  Original title: change file attributes

  I'm updating some drivers help Driver Whiz from HP.  The new drivers download but will not be installed.  Apparently, I need to remove the read-only file attributes, but no matter what I do it continues to change the next time I have access to the file to read-only.  Any ideas?

  Hi keuller,

  You can read the following article and check if it helps:

  You cannot view or change the read-only or the attributes of system files in Windows Server 2003, Windows XP, Windows Vista or Windows 7

  http://support.Microsoft.com/kb/326549

  Hope this information is useful.

• Get Windows Vista themes back please READ

  One night, after that I closed my laptop that I forgot to do something on the laptop and when I log in the computer froze several times. After that the Office had the appearance of task bars passed Windows Vista default to Windows Classic. Because it was late, I decided to put it off until the next day. When I opened the next day I was unable to access the control panel and the Customize option when you right-click the screen. When I restarted the computer, I was able to access both, but it took way to long than expected. When I opened the tab customize or properties and go to the themes tab, I was unable to find the default theme of Windows Vista. So now I'm stuck with some ugly theme. I scanned my computer COMPLETELY , used Disk Defragmenter and restarted the computer and nothing is the fix. The same problem of window will also the Internet. After all it the default theme has been well, deleted. Any chance to resume?

  Hello redfalcon67,

  To resolve this problem, use the tool (SFC.exe) System File Checker to determine which file is causing the problem, then replace the file. To do this, follow these steps:

  1. Open an elevated command prompt. To do this, click Start, click principally made programs, Accessories, right-click guest, and then click run as administrator. If you are prompted for an administrator password or a confirmation, type the password, or click allow.
  2. Type the following command and press ENTER: sfc/scannow (Yes there is a space after sfc) the sfc/scannow command analyzes all protected system files and replaces incorrect versions with appropriate Microsoft versions.

  To determine which files can be repaired by the System File Checker tool, follow these steps:

  1. Open an elevated command prompt.
  2. Type the following command and press ENTER:
     findstr/c: "[SR] cannot repair the military file" %windir%\logs\cbs\cbs.log > sfcdetails.txt

     Note The Sfcdetails.txt file contains details of every time that the System File Checker tool has been run on the computer. The file contains information about the files that are not repaired by the System File Checker tool. Check the date and time entries to determine the problem files that were found last time that you ran the System File Checker tool.

  3. Type the following command and press ENTER:
     Edit sfcdetails.txt

     The Sfcdetails.txt file uses the following format:

     The date/time SFC detail

  
  The following example of log file contains an entry for a file that could not be repaired:

  2007-01-12 12:10:42, info CSI 00000008 [SR] cannot repair the military record [l:34 {17}] "Accessibility.dll" of accessibility, Version 6.0.6000.16386, pA = PROCESSOR_ARCHITECTURE_MSIL = (8), VersionScope neutral, neutral culture, PublicKeyToken = {l:8 b:b03f5f7f11d50a3a}, type neutral, TypeName neutral, neutral public key in the store, file is missing "

  
  If the System File Checker tool cannot repair a file, follow these steps:

  1. At a command prompt, type the following command and press ENTER:
     takeown /f Path_And_File_Name

     For example, type takeown /f E:\windows\system32\jscript.dll.

  2. Type the following command and press ENTER to grant administrators full access to the file:
     ICACLS Path_And_File_Name/grant ADMINISTRATORS: F

     For example, type icacls E:\windows\system32\jscript.dll/grant administrators: F.

  3. Type the following command to replace the file with a known good copy of the file:
     Copy Path_And_File_Name_Of_Source_File Path_And_File_Name_Of_Destination

     For example, type copy E:\temp\jscript.dll E:\windows\system32\jscript.dll.

  
  Hope this helps you. Let us know anyway. Make it a great day!
  

  "In the end the love you take is equal to The Love You Make" (The Beatles last song from their latest album, Abbey Road.)

• I have a second hand on windows vista pc and it has only 1 login account and I have no password or any form of disks, how can I access windows in order to set up my own account

  I have a second hand on windows vista pc and he olny has 1 connection acount and I have no password or any form of records, how do I access windows in order to set up my own account / / / is no vista, discs or backup disks you not how I can get in using the computer

  http://support.Microsoft.com/default.aspx/KB/189126

  "Microsoft's strategy concerning lost or forgotten passwords"

  Microsoft cannot help you recover the passwords of the files and Microsoft who are lost or forgotten product features.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  Reinstall Vista:

  Vista recovery media obtain and/or use the Partition Recovery Vista on your computer to the factory settings .

  There is no Vista free download legal available.

  Contact your computer manufacturer and ask them to send a recovery disk/s Vista set.

  Normally, they do this for a cost of $ small.

  In addition, ask them if you have a recovery Partition on your computer/laptop to restore it to factory settings.

  See if a manual provided with the computer or go to the manufacturer's website, email or you can call for information on how to make a recovery.

  Normally, you have to press F10 or F11 at startup to start the recovery process...

  Another way I've seen on some models is press F8 and go to a list of startup options, and launch a recovery of standards of plant with it, by selecting the repair option.

  Or borrow a good Microsoft Vista DVD (not Dell, HP, etc).
  A good Vista DVD contains all versions of Vista.
  The product key determines which version of Vista is installed.

  There are 2 disks of Vista: one for 32-bit operating system, and one for 64-bit operating system.

  If install a cleaning is required with a good DVD of Vista (not HP, Dell recovery disks):

  Go to your Bios/Setup, or the Boot Menu at startup and change the Boot order to make the DVD/CD drive 1st in the boot order, then reboot with the disk in the drive.

  At the startup/power on you should see at the bottom of the screen either F2 or DELETE, go to Setup/Bios or F12 for the Boot Menu

  http://support.Microsoft.com/default.aspx/KB/918884

  MS advice on the conduct of clean install.

  http://www.theeldergeekvista.com/vista_clean_installation.htm

  A tutorial on the use of a clean install

  http://www.winsupersite.com/showcase/winvista_install_03.asp

  Super Guide Windows Vista Installation

  After installation > go to the website of the manufacturer of your computer/notebook > drivers and downloads Section > key in your model number > get latest Vista drivers for it > download/install them.

  Save all data, because it will be lost during a clean installation.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  http://support.Microsoft.com/default.aspx/KB/326246

  'How to replace Microsoft software or hardware, order service packs and upgrades, and replace product manuals'

  See you soon.

  Mick Murphy - Microsoft partner