Redefinicao de Senha of Bios Setup

Similar Questions

• How to enter the BIOS setup firmly

  8.1 - Whenstarting Windows that I'm trying to access the BIOS Setup. I push F2 repeatedlyeven after seizure-Toshiba screen is displayed. Almost always, I get on Windows system, only very few times I get to a tenth of a second at the left bottom of the screen saying line something like "to enter the BIOS. But then it is already too late to grab something. Is there a howto method course enter the savelie BIOS Setup? I have a Toshiba-computer laptop-P500-PSPGSE.
  Thank you very much in advance youvery.
  hansm

  F12 after start-up for multiboot-selection-Menu does not work either.

• 2430-101 stops at Toshiba-Logo (BIOS Setup/Boot-selection products deadloop)

  Hello.

  I have a serious problem with my Satellite 2430 101:

  The system stops at the start after reaching the TOSHIBA Logo. Pressing F2/F12-key appears common waiting messages ("enter in BIOS-Setup" / "entering Boot Device selection Menu) "), but the system hangs and then upward in a deadloop (you can hear the fan turning after a few seconds). Restarting with Ctrl + Alt + Delete system works perfectly, but as soon as it happens

  This is what happened before the last stop:

  I simply restarted the system (OS: Novell/SUSE Linux 9.3 kernel 2.4.xxx) and usual stop messages appeared. Then there was strange messages, which resembles BIOS-output (I'm sure it's no message-Linux)-I remember only something about "Boot PXE" and that it was an error message. After waiting some time (about 15 minutes), I rebooted manually by pressing the power button.

  I tried unplugging everything which has been connected to the system (including ModularBay devices) - without any result. I use the old BIOS 1.10 because there is no BIOS-update to the 2430-101 available in the downlads (maybe that was the problem). I also tried out the hard drive - even without a hard drive, the system displays the same behavior (if the hard drive is not the problem)...

  I hope someone can help me with this, because I need my laptop for my work...

  Thank you

  Post edited by: rpfaus

  Hi Rico,

  Have you tried to boot in SafeMode (PF8)? This should at least help you in your system to check for any errors.

  You can also try pressing them ESC when starting so that you can see the progress of the BIOS and the error messages.

  HTH

• Portege Z30 - cannot access the bios Setup

  Hello

  I can't enter BIOS setup when starting. Pressing on F2 allows me to enter the master password and HDD/SDD (confirmed validation), but the screen freezes at the "Toshiba configuration utility' graphics without any progress.

  This problem began to appear quite suddenly, I enter the setup of BIOS several times before without any problem. The only change that's happened that I know is an event of disruption/recovery failed.

  My suspicion is that the laptop is now in the start-up of hi-speed system. Can anyone confirm that? Is it possible to force it to boot normal start time? I'm using Linux, so I can't use the Windows of Toshiba Utilities.

  > I'm using Linux, so I can't use the Windows of Toshiba Utilities.
  That s bad:(dans le Toshiba HW Setup vous trouveriez un paramètre pour modifier l'option vitesse de démarrage.)

  > My suspicion is that the laptop is now in the start-up of hi-speed system. Can anyone confirm that?
  Hmm in my opinion, if the start-up speed would be set to fast, you wouldn't be able to press F2 and enter the BIOS password.

  However, in other cases, if the startup mode is set to fast, you can enter the first INS key BIOS and press the F2 key

  Give it a try.

• How to activate quickly publish in the BIOS Setup?

  Hello world

  does anyone know how to enable quick post in the BIOS Setup? This option seems not to be there in Configuration or maybe I'll only not on this issue the right way. Any help would be appreciated.

  See you soon
  AJMAL

  Quick post option does not exist and there is nothing to do. What you can try is to use a few hardware diagnostic tools.

• Key F12 C850-F0055 statellite access Bios setup

  Statellite C850-F0055 could not boot.it said check media (failure).
  I then change the boot from normal to quick start. Since then, his word
  "NO device bootable - please don't restart.

  When I press the F12 key to start it does not have the configuration of the bios.
  How can I change this back to normal fast start so that it can make the configuration of the bios. Help, please.

  > How do I change back to the normal quick start so that it can make the bios Setup?
  Open the office help > tools and utilities > system settings > starts and you will find option startup speed. Here, you can change back to the normal mode.

  Please try it and send feedback.

• Satellite L750 - 1 DM-how to enter the BIOS setup?

  Hi all.

  Tried several combinations of buttons - such as "DEL" or F' or F12 and so forth--but nowhere I could access the BIOS Setup.

  Does anyone have any useful information?

  Best regards.
  Robbs

  F2 allows to access the BIOS
  Press F2 quickly several times in line once the laptop has been powered.

• Satellite 1400-103: cannot access the BIOS Setup

  I have problems to enter the BIOS setup. At the start screen 1, I press ESC, and then check the system appears. Then press the F1 key. Once on the button, it takes me to the BIOS Setup and reboot the laptop. Any help will be much appreciated.

  James

  The laptop starts properly? I want to say is possible to get into the Windows operating system?

• How to enter the Bios Setup Satellite 4030?

  I am looking for information how to enter the Bios Setup.

  To enter the BIOS settings, use the ESC button.

• Y50 HUNGS ON THE BIOS SETUP

  My Y50 hungs in bios Setup, I can't use the arrows or anything like that...

  It's like that

  https://www.YouTube.com/watch?v=cauQ2NiuTIM

  My bios version is 1.09

  Ok...

  remove the ethernet cable... go to the bios Setup... disable PXE boot to lan... Save and reboot... Put your ethernet cable back on... don't go to bios again... no hunging...

• 4730 proBook s: when I try to access BIOS Setup, system diagnostics display

  Please help me guys
  When I try to access the BIOS Setup
  Diagnosis appear, and even impossible to access Boot Options
  
  I am pressing F10, and when I try one of these (Startup Options, BIOS)
  Please help me HP only in this one
  I'm in a lot of trouble at the moment, and if I can't solve this problem, I have to pay over $ 300
  Thank you

  Hello M.

  Remove the battery and the AC adapter, press the power 1 minute button to reset capacitors.

  Next step the unit only with the power adapter and press ESC at startup, and then choose F10 option.

  If the problem persists perhaps your HARD drive may have problems, then test the device without a HARD drive.

  Concerning

• Laptop HP ENVY M4: BIOS Setup Menu appears

  Dear support team,

  I have laptop HP ENVY M4. I try to activate the virtual technology on the laptop bios setting. I opened the boot as mentioned below:

  

  Press the f10 key to open the BIOS Setup, but nothing happens (not a single response). I tried to open the system, boot device Options Diagnostics but ended up with the same results. Here screen does not freeze. I work here the arrow keys. And one more thing at this point, I can only access Information System option.

  Any help would be appreciated

  Try the following:

  Press the power button and then immediately begin to type the F10 key at half-second intervals.

  The configuration of the BIOS screen display?

• Acer Aspire V3 - 772G - BIOS setup utility menus have disappeared

  Acer Aspire V3 - 772G - BIOS setup utility menus have disappeared

  I have install this laptop brand new, pre-installed with Windows 8.1 for my sister-in-law who bought it.  The installation went well BUT the 16 GB USB device I bought such as advised by the literature of Acer to store the recovery partition was not large enough, 14.4 GB physical capacity.  Acer the book says to use a 16 GB or more, so I did.  I naively thought that a USB key which has been marked 16 GB would be appropriate.  Not the case.  I had to buy a bigger but am still waiting for delivery.

  So I decided to any HARD drive to save the work I had done, but found only the Acronis Backup and Recovery DVD would not start the image.  I went into the utility configuration and adjusted the start parameters to inherited and modified device priority.  Acronis wouldn't so I did not continue.  I went back into the configuration utility, use F9 to restore the default value and to my astonishment that the DUAL boot option was now gone and Windows startup option was also gone.

  This means that £800 this laptop is now unusable.  The installer standalone reconfigured without warning.  Nowhere is there at - it advice or advice do not use the Setup utility when it erases the features that cannot be recovered by using F9 to restore the default configuration.  If this isn't a serious design flaw, I don't know what is.

  I am deeply worried because the idea of a BIOS setup utility behave in this way seems so unlikely that I wonder if anyone will believe me.  How are the Setup utility has been designed to self-harm like this?

  Your suggested action works!  Thank you very much.  You saved my life.

  loungehake

• Acer aspire 10th switch does not start the Bios Setup screen

  I'm trying to start on the bios Setup screen to change the boot sequence to test a rescue disk/windows 10 install usb, but all by pressing f2 during POST it just boots to windows of ideas anyone? Thank you

  power the device turned off, press and hold the power + Volume UP

  After awhile, it will boot to the BIOS.

• After flashing my Bios on Pavilion DM4t-1100 CTO, I can no more enter the BIOS setup

  After flashing my Bios on Pavilion DM4t-1100 CTO, I can no more enter into the BIOS setup (via the ESC key).  I installed the BIOS twice and the computer always ignores the ESC key and launches Windows 7.  Any ideas?

  Well you're response made me experiment more and I discovered that the ESC key works if I type repeatedly instead pressed constantly.  Thank you for taking the time to answer!