Reference Dell t620 showing PS1 PG Fail

Similar Questions

• Reference Dell T620 recognizes only 4 of 8 hard drives installed

  I bought 7 additional 2 TB drives for my Dell PowerEdge T620, delivered with just 1 such disk is almost a year now.  My model has 8 bays of HARD drive in front and after the installation of 7 new disks that I note that only four drives in the top row of the berries are recognized by THE system BIOS.  I'm running Ubuntu Server 12.04.4 and deliverance 'fdisk-l' lists only four disks, as well (sda, b, c, d).  I hope to set up the disks in a RAID 6 configuration if I can get the system to see eight - is it a simple BIOS setting change?  Please tell me that I don't need another controller or similar?  If it can help on the side of the Dell Support of things, my ST is deleted by the privacy policy.  Kind regards

  Mark D.

  In order details, Service number, listed only one RAID controller is the S110 RAID controller onboard.  The S110 is the lower-end controller you can get.  IF you are still using the controller, then the problem is your controller only supports a maximum of 4 disks, AND it does not support RAID 6 (only 0,1,5,10). You should use the H700 for a storage system like that anyway (or the H310 minimum).

  If you actually have a high-end controller, then you are very probably absent the second cable SAS controller to the bottom of basket.

• Reference Dell 8200 with the validation failed "VLK has been blocked by Microsoft."

  I have a Dell 8200 which now gives me a message saying that my VLK has been blocked by Microsoft. I was not reinstall or upgrade. I have a COA sticker on the case. How can I get a different key? I paid for a liscense good when I bought the PC. I tried to disable them with regedit then activating again with the same results. Help, please.

  You must change the product key on your system than on the COA sticker - to do this, use the product key update tool

  http://Windows.Microsoft.com/en-GB/Windows/help/genuine/product-key

• Reference Dell vostro 1520 with windows xp prof... Not reading CD/DVD

  Reference Dell vostro 1520 with windows xp prof... Unable to read & play any cd/dvd.tried mr.fixit content but no solution at the moment.

  Hello

  1 have. what fixit you tried?
  2. don't you make changes to the computer before the show?

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.Microsoft.com/kb/982116

  Important: To do: Important This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base: 322756 (http://support.microsoft.com/kb/322756/) how to back up and restore the registry in the window.

• Dell dimension windows xp restore fails to halfway through the process

  I had to change the video card that came with the reference dell dimension e510 has failed... Bought a new pc so was going to do a total restore back to settings during the windows xp loading & factory used the cd he couldn't got a failed error message using the usb ports then unable to use the keyboard than point & cannot go further... Help

  Hello

  I recommend you contact Dell support for assistance on this issue.
  http://en.Community.Dell.com/?~CK_=_mn

• Unable to install vista 64-bit sp2, his show Installation has failed.

  his show Installation has failed.

  Hi manjunathak,

  ·         Did you do changes on the computer before the show?

  ·         You get the error message?

  Follow these methods.

  Method 1: Temporarily disable the security software.

  Disable the anti-virus software

  http://Windows.Microsoft.com/en-us/Windows-Vista/disable-antivirus-software

  Note: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you do not disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network during the time that your antivirus software is disabled, your computer is vulnerable to attacks.

  Method 2: Put the computer in a clean boot State to see if there is a software conflict as the clean boot helps eliminate software conflicts and try to install the updates.

  Note: After completing the steps in the clean boot troubleshooting, follow the link step 7 to return the computer to a Normal startupmode.

  Method 3: Follow the steps in the Microsoft article mentioned below and check if it solves the problem:

  How to troubleshoot Windows Vista and Windows Server 2008 service pack installation issues

  http://support.Microsoft.com/kb/947366

  Problems with installing updates

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-problems-with-installing-updates

  Method 4: You can also manually install updates (KB number) by downloading from the Microsoft Download Center.

  http://www.Microsoft.com/downloads/en/default.aspx

  http://www.Microsoft.com/download/en/details.aspx?displaylang=en&ID=17669

  For reference:

  Learn how to install Windows Vista Service Pack 2 (SP2)

  http://Windows.Microsoft.com/en-us/Windows-Vista/learn-how-to-install-Windows-Vista-Service-Pack-2-SP2

  How to reset the Windows Update components?

  http://support.Microsoft.com/kb/971058

• Reference Dell MD3200i correct editing with IP system and the NIC for faster network speeds

  Hi all

  I worked on this project for a while now. I did a lot of research and have contacted Dell several times. I need help.

  I have 2 sets of identical to use for Hyper-V clusters servers. We bought a Dell MD3200i in November, we also bought a Dell 5424 switch and a Cisco SLM2048 switch. These servers have Real Tek 2 network cards for iSCSI Jumbo frames is 9 k

  The Dell MD3200i is two SAN controllers. Dell 5424 is the iSCSI optimized switch and Cisco is a 48 switch ports. iSCSI is on its own network that nothing else is connected to it. (There is an Iomega NAS and a promise Vtrak SAN Tech with all current domain of execution with iSCSI controller)

  Reference Dell MD3200i controller 0 Port 0 192.168.130.101 controller 1 Port 0 192.168.131.101

  Controller controller Port 1 0 192.168.130.102 1 1 192.168.131.102

  Controller controller Port 2 0 192.168.130.103 1 2 192.168.131.103

  Controller controller Port 3 0 192.168.130.103 1-3 192.168.131.104

  Cisco switch has 1 VLAN n ° 1 on it and the 130 subnet inside elements. There are 8 connections to the switch. 4 controller 0 and 1 of each of the servers. It has an IP of 192.168.132.4, but that switch IP does not make difference. Lighted Jumbo frames

  Dell switch has 2 of #1 for various things such as the domain controller, Vtrack, and SIN. Subnet 2 is 131 and has a total of 8 connectors inside. 4 in 1 controller and 1 from each of the servers. Lighted Jumbo frames. The switch IP address is 192.168.132.2

  Groups of servers. Each server node running Windows 2008 R2 SP1 and running hyper-v with virtual server clusters / storage folder on them. 2 Realtek NIC with Jumbo frames made 9 k ProdNode1 and ProdNode2 have 12 Core i7 CPU with 12 GB memory, EXNode1 and ExNode2 have 12 Core i7 CPU with 24 GB of memory.

  ProdNode1 iSCSI-1 192.168.130.110 ProdNode1 iSCSI-2 192.168.131.110

  ProdNode2 iSCSI-1 192.168.130.120 ProdNode2 iSCSI-2 192.168.131.120

  ExNode1 iSCSI-1 192.168.130.130 ExNode1 iSCSI-2 192.168.131.130

  ExNode2 iSCSI-1 192.168.130.140 ExNode2 iSCSI-2 192.168.131.140

  Portal discovery iSCSI on ProdNode1 went to 192.168.130.110 192.168.130.101 and 192.168.131.110 192.168.131.101 each of the other servers Discovery Portal have been pairs like this.

  iSCSI tab click on add 8 MPIO sessions at each of the ports on the MD3200i from Dell, target. For example, I added 1 session of 192.168.130.101 using it. Add Session,--> activate--> Advanced Mutlipath--> Local--> IP 192.168.130.110 initiator and target 192.168.131.101 iSCSI adapter. This is repeated on all servers. 4 connections for each NIC.

  The network is very slow. It revolved around 2 to 4 MB/MIN and it should be much faster. Initially, we had only the Cisco switch with only 1 VLAN and everything connected directly to it. I read somewhere that MPIO has been the problem, so I went through the same configuration but does not verify the MPIO checkbox above. Once this has been done, the network speed went up to 1.5 GB/Min but modular storage Dell was not happy, and virtual servers would fail and the connection is not very stable.

  What wrong with my setup? Can I directly home and fix the servers directly to the PowerVault and will make stable and allow for failover and redundancy NIC? I need to get this stable so I can move with something else.

  Thank you Ron

  You will need to change your system of intellectual property on this:

  rbramble

  EX-Node1 iSCSI-1 192.168.130.130

  EX-Node1 iSCSI-2 192.168.131.130

  EX-Node2 iSCSI-1 192.168.132.140

  EX-Node2 iSCSI-2 192.168.133.140

  Prod-Node1 iSCSI-1 192.168.130.10

  Prod-Node1 iSCSI-2 192.168.131.10

  Prod-Node2 iSCSI-1 192.168.132.20

  Prod-Node2 iSCSI-2 192.168.133.20

  Reference Dell MD3200i

  Controller 0 Port 0 - 192.168.130.101 Jumbo Frames 9K

  Controller 0 Port 1 - 192.168.131.101 Jumbo Frames 9K

  Controller 0 Port 2 - 192.168.132.101 Jumbo Frames 9K

  Controller 0 Port 3 - 192.168.133.101 Jumbo Frames 9K

  Controller 1 Port 0 - 192.168.130.102 Jumbo Frames 9K

  Controller Port 1 1 - 192.168.131.102 Jumbo Frames 9K

  Controller 1 Port 2 - 192.168.132.102 Jumbo Frames 9K

  Controller 1 Port 3 - 192.168.133.102 Jumbo Frames 9K

  Your iSCSI sessions will be:

  For EX-Node1:

  -192.168.130.130 to 192.168.130.101

  -192.168.130.130 to 192.168.130.102

  -192.168.131.130 to 192.168.131.101

  -192.168.131.130 to 192.168.131.102

  For EX-Node2:

  -192.168.132.140 to 192.168.132.101

  -192.168.132.140 to 192.168.132.102

  -192.168.133.140 to 192.168.133.101

  -192.168.133.140 to 192.168.133.102

  For Prod-Node1:

  -192.168.130.10 to 192.168.130.101

  -192.168.130.10 to 192.168.130.102

  -192.168.131.10 to 192.168.131.101

  -192.168.131.10 to 192.168.131.102

  For Prod-Node2:

  -192.168.132.20 to 192.168.132.101

  -192.168.132.20 to 192.168.132.102

  -192.168.133.20 to 192.168.133.101

  -192.168.133.20 to 192.168.133.102

• Reference Dell WinPE 5.0 driver CAB

  I have SCCM SP1 R2 and the Dell customer integration Pack 3.1 2012.  When I try to import the ACR 5 of WinPE from the SCCM console, it fails with 'the selected driver package is incompatible.

  Does anyone else have this problem?  My understanding is that SCCM R2 supports Win 8.1, which is what Win PE5 comes.

  Thanks in advance

  Tony

  Hi Tony,.

  Reference Dell Customer Integration Pack 3.1 is not support SCCM SP1 R2 2012. CAB WinPE cannot be imported via CPID 3.1 and it has to be injected for the boot image. Also try the last 5.0 WinPE that is available in the link below

  http://en.community.Dell.com/TechCenter/enterprise-client/w/wiki/5029.WinPE-5-0-driver-cab.aspx

  Thank you

  Pascale Raja

• Reference Dell 6224 and 5448

  Hi team,

  I'm new dell switches - exposed to cisco switches. I am faced with new kinds of problems with these dell switches. Unable to provide a fix and fight for the last 5 days. Pls help me. Below is my script

  Two nw - 2.0 and 3.0 is required to be configured in VLAN, VLAN ID 2 and 3.

  VLAN 2 - 192.168.2.1

  VLAN 3 - 192.168.3.1

  N/W 2.0 and 3.0 N/W machinery will be shared 48-Port powerconnect switch 5448 DELL

  The routing part arrives at 6224 power connect - gateway for vlan 2 - 192.168.2.1 and bridge for VLANs 3 - 192.168.3.1

  The switch of two is ascending through fiber optic - spf port cable

  This is the configuration I did-

  5448 switch-

  database of VLAN

  VLAN 2, 3

  output

  interface vlan 2

  switchport access vlan 2

  GVRP enable

  Routing

  output

  interface vlan 3

  switchport access vlan 3

  GVRP enable

  Routing

  output

  interface ethernet 1/you/1

  switchport mode general

  VLAN allowed switchport General add 2.3

  GVRP enable

  output

  interface ethernet 1/g1

  switchport access vlan 2

  GVRP enable

  output

  interface ethernet 1/g2

  switchport access vlan 3

  GVRP enable

  output

  Uplink port is TE1 (Layer 2) to XG2 (Layer 3)

  Reference Dell 6224 can connect

  Configure the terminal

  interface vlan 2

  no downtime

  IP 192.168.2.1 255.255.255.0

  Routing

  output

  interface vlan 3

  no downtime

  address 192.168.3.1 IP 255.255.255.0

  Routing

  output

  interface ethernet 1/xg2

  switchport mode general

  VLAN allowed switchport General add 2.3

  GVRP enable

  Computer with 192.168.2.100 / 24 GW 192.168.2.1 connected to layer 2 switch g1 - vlan 2

  When I ping 192.168.2.1 - accessible United Nations host destination

  Even the wise

  Computer with 192.168.3.100 / 24 GW 192.168.3.1 connected to layer 2 switch g1 - vlan 3

  When I ping 192.168.3.1 - accessible United Nations host destination

  Any thing that has missed out in the configuration part / all bad entries. I'm not sure now how to treat this. Pls help me and it is an urgent task for me

  Thank you

  With multiple VLANs, you need to use the general/Trunk mode. With the help of the info we have I made a diagram to help show the location of the switches and parameters on them. Obviously things can be different, such as PVID, IP address, VLAN ID etc are all customizable to your needs. But the page layout modes and the port will remain the same.

  

  STP will not fill the VLAN on the other switches. It's probably the GVRP feature it refers. With such a short race, it is more practical to manually add the VLAN. At least for the initial Setup, then once everything works enable GVRP to accommodate future expansion of VLAN.

  Hope this helps some.

• Reference Dell Force10 S50N time in the same newspaper

  Hello

  first of all, I hope that a good place to ask question re Force10 devices - if not please forgive & point me to the right place

  I have following two stacked devices:

  Type of system: S50N
  Reference Dell Force10 operating system Version: 1.0
  Reference Dell Force10 Application Software Version: 8.4.2.6

  Recently, I have configured a source of time using ntp. display the clock command returns good time & ntp config also seem ok.

  I want to have the switch which had the correct timestamp of the date unit % hour however when logging to show browsing results shows this:

  32w6d12h: STKUNIT1% m: % LACP CP...
  32w6d12h: STKUNIT1% m: % LACP CP...
  32w6d12h: % STKUNIT1-% M:CP CMEA...

  That I am, I lack to set up/set for the date & time stamped and posted in the event logs?

  (I'm beginner in world Force10 and switch)

  Appreciate any help

  Hello

  I found horodateurs service order before but I was so blind to enter config mode.

  That worked very well.

  Thank you very much

• Reference Dell R210 II - update the Firmware on Centos 6

  Hello

  I have several dell servers connecting a mix of OS linux centos 5/6 for windows and xen etc.

  I have run it on every Linux machine to install the dell tools:

  wget - q - O - http://linux.dell.com/repo/hardware/latest/bootstrap.cgi | bash
  yum install srvadmin-all firmware-tools - y
  yum install $(bootstrap_firmware) y
  srvadmin - services.sh status
  / opt/dell/srvadmin/sbin CD.
  update_firmware - Yes

  on centos 5 is very well and on some centos 6 machines too. However, a new server got us set up this week, the following error occurs, I want to know how to solve this problem, so I can perform upgrades in the usual way via command line:

  Root@server[/opt/Dell/srvadmin/sbin]# update_firmware - Yes

  Inventory of the currently running system.

  Search the directory for storage of the available BIOS updates...
  Checking the BIOS - 2.2.3
  Available: dell_dup_componentid_00159 - 2.2.3
  Did not find a new installation package that meets all the checks of the facility.
  Verification of rev NetXtreme II Gigabit Ethernet 20 (em2) - 7.2.20 BCM5716
  Available: pci_firmware (ven_0x14e4_dev_0x163b_subven_0x1028_subdev_0x04dd) - 7.4.8
  Found update: pci_firmware (ven_0x14e4_dev_0x163b_subven_0x1028_subdev_0x04dd) - 7.4.8
  Check the system BIOS to PowerEdge R210 II - 2.2.3
  Did not find a new installation package that meets all the checks of the facility.
  Verification of rev NetXtreme II Gigabit Ethernet 20 (em1) - 7.2.20 BCM5716
  Available: pci_firmware (ven_0x14e4_dev_0x163b_subven_0x1028_subdev_0x04dd) - 7.4.8
  Found update: pci_firmware (ven_0x14e4_dev_0x163b_subven_0x1028_subdev_0x04dd) - 7.4.8

  Found the firmware that needs to be updated.

  Updates running...
  -Installation of pci_firmware (ven_0x14e4_dev_0x163b_subven_0x1028_subdev_... Package installation failed: pci_firmware (ven_0x14e4_dev_0x163b_subven_0x1028_subdev_0x04dd)
  -7.4.8.
  aborting update...

  The command to low-level error message was:

  Unable to parse xml output, bad for the package: pci_firmware (ven_0x14e4_dev_0x163b_subven_0x1028_subdev_0x04dd)
  Root@server[/opt/Dell/srvadmin/sbin]#

  the specification of the server:

  Reference Dell R210 II

  Intel Quad Core 3.2 Ghz
  16 GB of Ram
  CentOS 6.4 x 64
  1 x 256 GB SSD

  ChrisDuk112,

  Could you do me a favor and see if that solves the problem for you.

  the remount mount - o, suid, exec/tmp

  Let me know how it goes.

• Reference Dell 1700 crashed and I have no backup

  Reference Dell 1700 crashed without backup whats a girl to do
  
  

  lost all programs can run does not help

  Reference Dell 1700 crashed without backup whats a girl to do

  
  

  lost all programs can run does not help

  Reinstall Wndows.

  Reinstall all your programs from the original media or downloaded files you have saved on an external drive.

  Reinstall all your data from the backups that you made on an external drive.

  If you have not, you're out of luck.

• Cannot print. Reference Dell 944 communication usb port is not available. error check your firewall settings to ensure the printer communication is not blocked.

  Original title: unable to print. Reference Dell 944 communication usb port is not available.

  Message says 'check your firewall settings to ensure the printer communication is not blocked. Printer has worked faithfully until the problems started with the XP Home operating system. To cut a long story short ram upgraded to 2 GB, all unnecessary programs identified and technician Microsoft contacted to solve problems.  I was informed of problems caused by 3rd software party conflicts. Kaspersky was apparently the culpit. Dell Inspiron 32 now much faster but the printer will not work little matter what I do. I tried to reload with drivers & utility CD, drivers uninstalled & reinstalled on the site of all nothing is? Can someone help?

  DavidNicholsonXN,

  How to download and install drivers in the correct order

  also try to read...

  The owners of all-in-one printer Dell 944 thread (W7)

  Let the printer after Kaspersky

  Rick

• Reference Dell pc with xp family. Restart to the logon screen

  Reference Dell pc with xp family. Restart to the logon screen. starts ok in safe mode. run msconfig and do that no change then do restart ok everything ok until the cold start, then hand it to restart?

  Peek into the registry to find clues.

  Disable the automatic restart in case of system error and see if you can capture a message of error checking bug (BSOD) with useful information.  Automatic restart in the event of system failure can be disabled in the F8 advanced boot menu, or you can turn it off in system properties.

  1. right click on my computer and select Properties.
  2 - Click on the Advanced tab, and then click on the Start button and recovery settings.
  3 clear the automatically restart box and OK your way out system properties.

  Start the computer in a Clean Boot State, if the computer starts successfully in a clean boot state, then one of your user programs most likely problems, look in the case of journal of indexes.

  How to configure Windows XP to start in a "clean boot" State
  John

• Office Jet 6500 Wireless: print works do not showed "filter has failed."

  My Officejet 6500 wireless works very well on the scan, but will not be printed. It showed "Filter has failed" and paued on wirelss or plugged USB cable?

  Hi there @Hsiu

  Welcome to the forums

  I understand that you see a message "Filter failed" when you try to print from your Mac, with the Mavericks. I have a few steps that I would say that you follow below that should help you.

  1. Mac OS X: how to reset the printing system
  2. Repair disk permissions
  3. Restart the Mac.
  4. Follow this guide: install a printer Mac driver by using Apple Software Update
  5. In addition, to download this driver: HP v3.0 for OS X printer drivers

  Good luck, I hope it works!