reinstall of LabVIEW 2010 problem

Similar Questions

• LabVIEW 2010 FPGA: problem with the mean and the variance Subvi

  The Subvi 'Average, Variance and standard deviation' seems to not work properly. The calculation of the average value is ok but std and variance are bad and the results change with representation in an unexpected way. Everyone knows about this problem? Is there a problem with the use of this function?

  Thank you

  Andrea

  Hello Andrea,

  Here is a test for the configuration of your VI (entered I16, 16 samples), saved in LabVIEW 2010 SP1 and the new Subvi. It is relatively simple to adapt it to other configurations, but it does not reconfigure several nodes and constants on the diagram. Let me know if it will work for you.

  Kind regards

  Jim

• Files reading TDMS problem in Labview 2010, created in 2009, error-2503

  I did my measurements on my laptop with Labview 2009 installed.

  The file format has been TDMS v1.0

  I can read these files with the TDMS files viewer and I am able to do analysis on my laptop.

  On my desk I have Labview 2010.

  If I run the vi in Labview 2010 analysis, I get the following-2503 error: specified file does not have the PDM file format standards.

  What's wrong?

  I can open the file in Excel with the add-in.

  I've included a tdms file created on my laptop in Labview 2009

  For this problem, it's a bug in LabVIEW 2010 (not in previous versions of LabVIEW), sorry for the inconvenience. While the side R & D to fix this problem, we also a workaround solution, but perhaps a little more complicated:

  (1) Please use older version of LabVIEW (like 2009 or 8.6) for defragement file by using the node TDMS defragment, if it works fine, you can then open it défragmentée TDMS in LabVIEW 2010.

  (2) if the PDM defragment returns an error, then you can always find your defragmened files in the temp directory of Windows, but under a different filename (randomly generated), you can type "%Temp%" Run windows to open your temporary file.

• I get the error indicating the niajel.dll missing for HSDIO in labVIEW 2010, can someone help how to solve this problem.

  I'm using LabVIEW 2010 and installed the drivers from device LV2010 and try to use the HSDIO functions, while setting the HSDIO function on the block diagram showing niajel.dll is missing, can someone help me fix this bug.

  I tried to uninstall and install not able to set several times.

  Hello. niajel.dll corresponds to the NOR-TClk, although NEITHER-HSDIO does not specifically use it. You use certain functions TClk?

  Also, what other PXI device driver are installed on the system? Could you give a report on the MAX system?

• HOWTO fix Labview 2010 delays

  My Labview 2010 causing huge delays ~ 30-40 years compiling and when using the restore function.

  It blocks the (useless) pc for its time.

  I tried several times now, but the work of development with this break is not possible.

  System: MS XP32, Athlon 64 3800 + with 2 GB of RAM is not recent, but clearly within the min. requirements: Pentium 4 and 1 GB

  The app is first written as LV 6.4/8.0 and use very less stuff express vi.

  HOWTO solve the problems of delay with LV coming 2010?

  1. do I need to rewrite my whole program express screws...

  2. can I disable certain features to reach LV 8.0 performance...

  3 do I need a faster cpu and more RAM...

  ((4 can I I restore this program to OR because of) a lack of compatibility and b) minimum requirements of evil

  BTW... can Labview be completely uninstalled at all...?

  Sorry to ask a little aggressive but this "program OR" cost me a couple of days now for nothing

  Tips in particular to Question 2 would be much appreciated...

  read it twice, I discovered a very interesting aspect now your answer Putnam... Thank you

  I think this indicates that the solution...

  sound in this line here...

  > Currently using LV 6.1 - LabVIEW 2009, RT8.5

  I'll go and reinstall 8.0 and available banks of LV and recommend seriously

  for all LV users do not update to LV 2010.

• error in the specification of the build in the Project Explorer (Labview 2010)

  Hello

  I'm having a problem with building my folder in the Project Explorer after installing Labview 2010. Error occur said that as an attachment. I already reinstall back the software especially devices or. still having the same problem.

  Hello

  The problem is solved after I installed Labview 2010 sp1 patches... Thank you responded and give an idea and opinion...

• How to sit interface with matlab 2010A and labview 2010

  I use tools of simulation interface 5.0 with matlab 2010A and labview 2010, I want to take my cue from matlab, labview but signal transfer, I am facing a problem. I want to know is there any compatibility issue in sit 5.0 or I do something wrong?
  photos of errors are attached.

  natasftw wrote:

  http://digital.NI.com/public.nsf/allkb/02F5FA55FC28BDE1862578A30071F975
  While it is for 2011, I doubt that they decided to remove 64-bit compatibility as they went forward as 64-bit has become more rather than less demand.  In this document,notes LabVIEW Simulation Interface Toolkit does not support 64 bit versions of MATLAB application software."

  The extent of the compatiblitly for 32 - bit, I'd take a peek at: http://digital.ni.com/public.nsf/allkb/D174674A91E5536286257428005C2426

  The OP's question was SIT support 64 - bit version of LabVIEW and 64-bit version of the MATLAB/Simulink itself, not the operating system software.

  Document in your second link is on a completely different topic to have API for LabVIEW and MATLAB/Simulink/RTW (well, mostly Simulink & RTW). Here is the relevant link for the 32-bit compatibility: http://digital.ni.com/public.nsf/allkb/049295038FF0EE2A86257A06006B2DAD is no SIT 64-bit.

  Other underlying issues is that Pharlap does not have a 64-bit version. Finally, simulations are better performed on some RTOS (embedded PXI) for a deterministic execution rather than PC operating systems.

  -BTC

• LabVIEW 2010 help control Source code...

  I'm trying to set up Tortoise SVN to work with LabVIEW 2010.  I was able to get lvmerge and lvcompare to work by adding them to the list of programs within the turtle, but leave in LabVIEW there is a section to configure the source control I have a problem with.  Under "Configure Source code control" there is a drop down to the name of the Source control provider.  There is only one option: < none=""> .  I looked into it a bit online and found that LabVIEW running in Windows searches the registry database for a list of the sources of control.  I don't know exactly what he's looking for in the registry, but maybe I could make an entry in the registry to get LabVIEW see Tortoise SVN.  Anyone had this problem or any experience with this?

  To use the NCC options provided by LabVIEW you will need from a provider. For subversion, it is possible with the PushOK SVN SCC plugin.

  If you install you can checkin/checkout directly from the LabVIEW project environment.

  If you really like TortoiseSVN discover the Tortoise SVN integration made by JKI-software.

  Tone

  PS there is nothing special about 2010 in the integration of the CSC.

• Thread mode in LabVIEW 2010 bug?

  I had an application written in LabVIEW 2009 for a PSC-2220 who stopped working when it was converted in LabVIEW 2010, and I tracked down the problem to one thing: the software sets the mode of the Serial wire. Call this method simply disables all of the program. It works when you run from LabVIEW... but if you build an application to start it will not start. Remove the call to thread mode - and voila, the application runs as it should.

  -I can solve the problem easily by calling does not fashion wire method, but this isn't a solution due to the fact that I need to use the RS-422/485 port RS485 2-wire mode.

  I found a solution that I can live with... it does not explain what is wrong, but here's what I had to do to be able to run the init.vi serial port from outside vi.lib\Instr\ - which in turn allowed me to add the changes I need (set the thread mode) without having to edit a library function :

  I had to flatten, i.e.replace all of its report with their content... I could have tried the inline function, but did manually to be sure.

  This may indicate that something is wrong with the binding when the program is compiled with RT... but it happens without producing errors of conflict or anything either. A startup.exe is produced - but is not able to run.

• LabVIEW 2010 executable runs under windows xp, but not in windows 7

  Hi all.  Here's the situation.  We have Labview 2010 professional development on a computer running Windows XP.  I designed all my programs with this PC.  We have another PC which has Windows 7 with no Labview.  I'm trying to make the executable files and put them on the Windows 7 PC.  I have been here three executable files and move the Windows 7 PC.  One of the executables work correctly, the other two interrupt immediately.

  Executables that stop have temperature limits and the program is apparently seen a low temperature and so stop the program.  Yet, these same executables work fine on the PC under Windows XP.  What seems to be the case, is that the program is expelled before allowing himself read the temperatures.  I use the modules of the series C 9213 and 9211 with 9188 Chassis.   My programs are showing 0 for temperatures.  Well, it's certainly in the low temp limit, so the program stops.  However, she should not do this.  I know there is little delay with the playback of all thermcouples in 9213 and 9211 modules, but this was not a problem with Windows XP.  Even if the program starts from scratch on the XP PC, temperatures immediately appear, or appear after a second or two.  Yes, I've rarely seen a temp 0 on the XP PC, but the program doesn't stop; Give it a second or two and the time appear.  Why is it that happens in Windows 7?

  An executable that works has no measure of temperature.  It uses only 9481 modules and run the solenoids at a rate of about 0.2 seconds.  This executable works fine on both computers.

  So what - this on the modules of temperature reading that is causing a problem in Windows 7?

  Other installation data :

  -The XP PC has the updates Labview 2010 is compatible with

  -The PC Win 7 not the latest updates of Labview 2010 there are has compatibility problems.  National Instruments has given me the compatible components, and they has several levels down by the most recent (for example MAX vs MAX 5.6 v14.0)

  
  

• 'LabVIEW 2010'.exe as a windows service running

  Hi all

  years, I wrote an application with LabVIEW 7.1 and transformed into a Windows NT Service according to this NOR-tutorial.

  Now, I have a similar use case and I wanted to do the same thing with an application built in LabVIEW 2010.

  Somehow, it does not work and I still get the error 62.

  I built a simple demo application once with LV7.1 and once with LV2010.

  I was able to use this service when they built with LV7.1 but not the version of LV2010 (client-side I always used LV2010). He has no problem with the connection to the server or using the port.

  I'd rather not rebuilt the app with LV7.1 because it is not really small. I consider that if there is no work around for this problem.

  Anyone any ideas?

  I really appreciate anyone's help

  See you soon,.

  Christian

  As well as information for those who execute it in the same problems:

  SC.exe toured BUT not as described in this tutorial. You must create a wrapper function as described on this Homepage. Services created with sc.exe need a BeginService() and an EndService() method otherwise it wont let you install.

  This image shows you how I did it. The CIN AnyService.dll of charges that loads server.dll.

  Kudos to Kuan Chen

  

  See you soon,.

  \c

• No material listed in Labview 2010 Linux DAQ

  Hello

  I have a problem with DAQmx Base 3.4.0 under Linux:

  mxbaseconfig shows my NOR-6009 device to the USB port. I can also create tasks corresponding to the nor-6009 in there. When I try to create a task in Labview 2010, one of the constant I/O are always empty. Dropdown menu arrow is grayed out. If I get the name of the device directly in the constant, he through me an error :-( Do not know Semms like Labview, which DAQmx Base instruments are connected...

  With devices VISA, I don't have this problem. All VISA devices are displayed in the dropdown of the constant and work correctly.

  lsdaq gives me:

  --------------------------------
  Detect of National Instruments DAQ devices
  Find the following materials:
  NEITHER 6220: "Dev1" (PXI1::4:INSTR)
  OR USB-6009: "Dev2' (USB0::0x3923:0x717B:0119B3BD: RAW)
  --------------------------------

  I use

  RedHat Enterprise Linux 5.5

  NI - 488.2 - beta - 2.51 b 1

  NI-VISA - 5.0.0

  NOR-DAQmx Base 3.4.0

  LabVIEW 2010

  All installers worked well...

  No idea how to access my OR-6009?

  Felix1234 wrote:

  It the device port ID is connected by a string variable to the Vi DAQmx Base... also works perfectly for me. But I do not know why the variable I/O noit work...

  DAQmx Base does not have controls that LabVIEW as DAQmx done [1]. Because the driver does not use background services, it cannot be said LabVIEW what devices and channels are available on the system.

  [1] NEITHER-DAQmx Base tasks and physical channels are not listed in the task of LabVIEW and string constants and controls
  http://digital.NI.com/public.nsf/allkb/57393FEDF313E99B86256F0B0010AD2D

• Labview 2010 8.1 Windows executables

  Greetings,

  My development computer is a Windows 8.1 with LabView 2010 Professional machine. I created a project and published an executable with success. Obviously this works on my development system.

  However, I have another machine Windows 8.1 (new installation, nothing about this). First, I installed the runtime Labview 2013 because (a) I thought that it would be compatible for older versions, and (b) it says it supports the Windows 8 operating system. Unfortunately when I tried to run the executable it gives me the following error:

  Could not locate the LabVIEW runtime engine.

  .. .requires a 2010 version (or compatible) Labview engine of execution. Contact the seller to [name of program] to correct this problem.

  Okay, so I uninstalled the runtime of 2013 and restarted. Then I installed 2010 thought that is what it takes.

  Gives me the exact same error as above.

  I saw similar problems of windows 8, but nothing I could find about it.

  What I am doing wrong?

  Thanks in advance.

  Why install the runtime 2013 when you have an application of 2010? You must also install the appropriate number of bits of the runtime.

  Why not simply create an installer?

• Extremely slow LabVIEW 2010 icon editor

  Working on a project of medium size in LabVIEW 2010.  Out of the blue icon editor is slowing down.  So slow that type in a character of text takes 20 seconds.  After closing, the editor he is about 3 to 5 second rule on everything that I do in LabVIEW.

  LabVIEW games restart things back to normal, until I open the icon editor.  No results of Subvi opening in this problem.  And this happens in any project or even if no project is open, and I'm trying to change the icon in a Subvi Untitled 1.

  Anyone else seen this behavior.  I really want to re - install LabVIEW 2010.

  Thank you

  I've not seen this behavior, and I really have no idea what could be the problem. As a solution, we can 'turn off' icon editor and force LabVIEW to use the old classic that is causing the problem to go, in my opinion. To do this, rename the following lv_icon.bak:

  [2010]\resource\plugins\lv_icon.vi LabVIEW

  This will completely ignore the code from the editor of icon and go directly to the editor of classic icons. You will lose a lot of the new functionality of the icon editor, but I'm guessing that this will make the downturn go away.

• Labview Remote problem

  Hello!

  I have a NI USB DAQ of 6341 who assume to control a horse trough PMT and LED Labview 2010.

  But, Labview is not installed in my PC, I use it remotely from the University and I am facing problem to use DAQmx (version 9.3.5) in Labview.

  What I want to know is how to make my remote Labview for data acquisition in my computer.

  I guess it's a very simple question, but after hours trying to find a solution, I decided to ask the experts...

  Thank you!

  Hello RadGent,

  This solution will not work in your case.

  However with NOR-DAQmx 8.0 and later, NOR-DAQmx OPC features can be used to obtain the features of reliable network of remote systems.
  GDR (as mentioned in the document you provided) is not supported in NOR-DAQmx.

  You can try something like this:

  http://zone.NI.com/DevZone/CDA/tut/p/ID/3742

  The best and the most simple of measures to be taken would be to install the software locally, especially because you are working with a USB device.

  Goes on ethernet, at University, then return in the same pc to connect to the DAQ card would seriously increase the latency of the system.