remote offices VPN to PIX then Internet

Similar Questions

• L2l VPN and remote access VPN

  Hello

  I have 2 Cisco Pix (Pix1, Pix2) 515E (8.0.4). Between these devices exist VPN L2L, which are configured on the external interfaces. On Pix2 I configured remote access VPN on the external interface, too.

  Is it possible to achieve LAN behind Pix1, by using remote access VPN on Pix2 then VPN L2L?

  I don't want to set up remote access on Pix1.

  Thank you very much.

  Kind regards

  Vladislav

  NAT (outside) 1 140.40.30.0 255.255.255.0 (PAT for RA vpn to access the internet if you complete tunnel)

  It is simply because I have configured tunnel RA as complete tunnel instead of split, nat (outside) 1 at the RA 140.40.30.0 pool have internet access through your firewall ASA_SITE_B and translate with global ID 1 who is your external interface of the firewall SA_SITE_B. This has nothing to do with what you are trying to accomplish, but I posted it because it was part of the very common scenario. There are some example PIX 6.3 cases where you will need split tunnel so that RA users have internet access not passing not through the encrypted tunnel code 6.0 does not feature of intra-interface support but 7.x above is of the code. Other examples are that some people configure split RA RA user tunnel will have access to their local resources in their homes as the printers network etc...

  It is therefore, I need to translate 172.27.1.0/24 RA pool?

  No there is no address translation in place in this scenario to work and you don't need to translate something too long, there is no of networks that overlap in one of the SITES u do not need to translate, this scenario is completely free sheep as you access lists free of nat in two firewalls for networks involved in communication in tunnels ASA_SITE_B.

  Because I want to see IP addresses from PIX_SITE_A to 172.27.1.0/24, not 140.40.30.0/24. Is it possible to do it this way?

  Im not clear on this issue, but if I think what it means, it's possible but you need to have political NATing but I think this will make complicated setup, I would say to make this as simple as possible.

  Concerning

  All helpful PLS rate valid if it helped

• NAC Appliance with ASA (for remote user VPN)

  I have a pair of firewall 5520 cisco which is used as a VPN gateway (for remote user VPN) and perimeter firewall Internet (to provide outbound internet connectivity).

  We allow the NAC to remote VPN users. I have it will be deployed with active 3 layer inband.

  The problem with this design is that how to ensure that outgoing internet traffic does not pass through the CASE?

  I heard about couple of optioins:

  -ACB (for send only IP subnet to VPN users remote to go through CASE)

  -Version 8.x characteristic of ASA (Restrcit access to VLAN under Group Policy).

  I intend to do with ASA firewall where I can set a new subinterface on the SAA (with a new tag VLAN) and under the group policy for remote user VPN, I select the option to "restrict access to the new VLAN.

  My question is: is - it still works (even if the firewall have a route to the internal network by using the 'inside' interface and NOT the new interface of the NAC). If this does not work, please let me know what are the other options for this type of deployment.

  Thanks in advance.

  Hello

  It should work. Please see the attached PDF for more clarity on this topic: https://supportforums.cisco.com/docs/DOC-9102

  HTH,

  Faisal

• PIX 515E and remote access VPN

  I use a PIX 515E with: ASDM Version: 5,0000 51 PIX Version: 8.0 (4) and configure it with remote access VPN.

  I would like to get an email every time that a user login (and or disconnection) to the VPN. Remote clients use the Cisco VPN Client.

  Any help is appreciated,

  Hello

  Here is a link to the email configuration when you log in to the ASA/PIX: http://www.cisco.com/c/en/us/support/docs/security/pix-500-series-security-appliances/63884-config-asa-00.html#anc7

  Then you can create a list of message to send the logs only for the connection/disconnection of the VPN user: http://www.cisco.com/c/en/us/support/docs/security/pix-500-series-security-appliances/63884-config-asa-00.html#anc18

  There is a wire that is linked here: https://supportforums.cisco.com/discussion/10798976/asa-email-logging-issue

• L2L pix 501 and remote access VPN

  Hi, I'm working on an old 501 PIX w / Software 6.3 (5), he already have access to remote VPN configuration and works very well, but now he needs a L2L implemented. One thing I try to do all the work remotely via VPN or ssh to the machine. I don't know what's on the other end, but they swear that it is set up and maybe my problem is when I start putting in orders for the other VPN it breaks the remote VPN access. One thing that I have to do is NAT a host on the inside to appear as another host on the end. I use these commands and I think it works cannot be said.

  access-list 101 permit ip remote_network 255.255.255.0 local_server host

  public static 10.1.0.203 (inside, outside) - access list 101

  then

  access-list 102 permit ip host 10.1.0.203 192.168.50.83
  access-list 102 permit ip host 10.1.0.203 192.168.50.86
  access-list 102 permit ip host 10.1.0.203 192.168.50.50
  access-list 102 permit ip host 10.1.0.203 192.168.50.85

  and use it to match against

  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
  EMDs-map 10 ipsec-isakmp crypto map
  correspondence address card crypto emds-map 10 102
  card crypto emds-map 10 peers set remote_vpn_server
  card crypto emds-card 10 set of transformation-ESP-3DES-SHA

  then

  ISAKMP key magic_key address remote_vpn_server netmask 255.255.255.255
  ISAKMP identity hostname
  part of pre authentication ISAKMP policy 10
  ISAKMP policy 10 3des encryption
  ISAKMP policy 10 sha hash
  10 1 ISAKMP policy group
  ISAKMP life duration strategy 10 86400

  and that is where it usually breaks the VPN, I don't know if the other VPN works due to not being not able to get to this server to try to ping, I don't really like to try this stuff remotely but I don't have a lot of choice at the moment.

  Any thoughts?

  Thank you

  Jarrid Graham

  Yes, just use the number of different sequence with 1 name of the crypto map. Please also ensure that your dynamic crypto map, which is your vpn client has the sequence down the crypto map (more), because you want to make sure that the static crypto map (for lan-to-lan tunnel has higher sequence number (lower number)).

  The political isakmp sequence number does not match, it is processed from top to bottom (number less than the high number) and also long 1 set of isakmp policy corresponds to the remote peer, it will be negotiated properly.

  Hope that answers your question and please note useful post. Thank you.

• Connected to the Internet of VPN remote access VPN clients

  Greetings,

  I need to remote VPN clients to connect to the Internet from the same server VPN ASA

  "client connects to ASA the external interface VPN tunnel can access Internet from the same external interface ASA new."

  Thank you

  you need to configure "same-security-traffic permit intra-interface" on the SAA.

  Also, need to configure the relevant statements of nat for your range of pool of customers.

  i.e.

  Global 1 interface (outside)

  NAT (outside) 1 access-list anyconnectacl

  where anyconnectacl is the pool for your customers:

  permit ip 172.16.1.0 access list anyconnectacl 255.255.255.0 any

• Remote access VPN pix version 8.0 (3)

  Hi all

  First of all, I would like to thank to all members of the forum who got help in several messages on the configuration of the pix 515.

  I am now configuring remote VPN access with radius authentication to my network, but I can't connect.

  I use the cisco vpn client 5.0.03.0560, I have also tested my pix radius (inside) server authentication and works very well.

  I already tried to retype the key of the cli, but I still can't remote access vpn to work.

  I also tried to create another remote vpn with another name and local authentication, but I have the same problem.

  I use 8.0 (3) version pix.

  Can someone help me

  I attach the log file of the cisco vpn client to help solve the problem, as well a configuration of the pix folder.

  Thank you very much in advance and I seek prior information.

  http://www.Cisco.com/en/us/docs/security/ASA/asa72/configuration/guide/vpnadd.html#wp999516

  [Pls RATE if HELP]

• Access remote VPN, no split tunneling, internet access. Translation NAT problem

  Hi all, I'm new to the forum.  I have a Cisco ASA 5505 with confusing (to me) question NAT.

  Unique external IP (outside interface) with several translations of NAT static object to allow the redirection of port of various internal devices.  The configuration worked smoothly during the past years.

  Recently, I configured a without the split tunneling VPN remote access and access to the internet and noticed yesterday that my port forwarding has stopped working.

  I reviewed the new rules for the VPN NAT and found the culprit.

  I've been reviewing the rules again and again, and all I can think about and interpret it, I don't know how this rule affects the port forwarding on the device or how to fix.

  Here's the NAT rules, I have in place: ('inactive' rule is the culprit.  Once I have turn on this rule, the port forwarding hits a wall)

  NAT (inside, outside) static source any any static destination VPN_Subnet VPN_Subnet non-proxy-arp-search to itinerary
  NAT (outside, outside) static source VPN_Subnet VPN_Subnet VPN_Subnet VPN_Subnet non-proxy-arp-search of route static destination
  NAT (outside, outside) source VPN_Subnet dynamic interface inactive
  !
  network obj_any object
  NAT dynamic interface (indoor, outdoor)
  network of the XXX_HTTP object
  NAT (inside, outside) interface static tcp www www service
  Access-group outside_access_in in interface outside
  Route outside 0.0.0.0 0.0.0.0 xxx.xxx.xxx.xxx 1

  Any help would be appreciated.

  Try changing the nat rule to VPN_Subnet interface of nat (outside, outside) the after-service automatic dynamic source

  With respect,

  Safwan

• Information on the routing of traffic of the client VPN to PIX.

  Hey all,.

  I could follow the VPN Wizard included in the PDM and able to connect with the VPN Clients for the PIX. But I'm looking for more information about how the routing is done.

  For example, my remote is 67.71.252.xxx and my inside is 192.168.1.xxx. But if I connect via VPN to PIX Client, all data is transferred through my VPN to PIX and then trying to get out to the Internet.

  I'll settle for data goes 192.168.1.xxx for transit through the VPN. This configuration made via the PIX or is it the responsibility of the Client machine to set up rules of the road?

  All links to the guides to installation, or technical notes would be great.

  Thank you inadvance.

  Paul

  Hello

  I think the key word you are looking for is "split tunneling". This can be validated on the PIX using the vpngroup split access_list tunnel GroupName command.

  "Split tunneling allows a remote VPN client or encrypted simultaneous Easy VPN remote access device to the corporate network and Internet access. Using the vpngroup split-tunnel command, specify the access list name with which to associate the split tunneling of traffic. "

  In this example configuration: http://www.cisco.com/warp/public/110/pix3000.html, note that the same access list is used to "nat 0" and split-mining:

  access-list 101 permit ip 10.1.1.0 255.255.255.0 10.1.2.0 255.255.255.0

  (Inside) NAT 0-list of access 101

  vpngroup vpn3000 split tunnel 101

  Order reference:

  http://www.Cisco.com/en/us/products/sw/secursw/ps2120/products_command_reference_chapter09186a00801727ae.html#wp1099471

  Please let us know if this helped

  Kind regards

  Mustafa

• Road of default remote access VPN session

  ASA version 8.2.2

  How do you assign remote access VPN sessions a single default route?  Other than the default route assigned to ASA.  For example, my VPN ASA (handles vpn sessions), defaults to the Internet.  I wish that sessions VPN for remote access by default internal network first, then follow the default route to the Internet on another firewall.

  The SAA outside the IP address of the interface is a public.  Inside is a private 10.x.x.x.  VPN clients receive 172.17.x.x.

  Thank you

  After the command 'road' added keyword "tunnel".

  in the tunnel

  Specifies the route as the default gateway of tunnel for the VPN traffic.

  http://www.Cisco.com/en/us/docs/security/ASA/asa80/command/reference/QR.html#wp1767323

• Help the Site VPN Site PIX 501

  Hello

  I'm pretty new to PIX firewall, so I hope someone here can help me.

  I have two PIX and try to create a private network virtual between the two PIX. I posted the configs below.

  The problem is that I can ping PIX on a PIX two, but I can't ping the servers behind TWO PIX. On two PIX, I cannot ping PIX ONE or all the servers behind it.

  Any advice would be appreciated.

  Thank you

  PIX 1

  6.2 (2) version PIX

  ethernet0 nameif outside security0

  nameif ethernet1 inside the security100

  hostname TMAXWALES

  domain ciscopix.com

  fixup protocol ftp 21

  fixup protocol http 80

  fixup protocol h323 h225 1720

  fixup protocol h323 ras 1718-1719

  fixup protocol they 389

  fixup protocol rsh 514

  fixup protocol rtsp 554

  fixup protocol smtp 25

  fixup protocol sqlnet 1521

  fixup protocol sip 5060

  fixup protocol 2000 skinny

  names of

  inside_outbound_nat0_acl ip 192.168.254.0 access list allow 255.255.255.0 192.1

  68.1.0 255.255.255.0

  outside_cryptomap_20 ip 192.168.254.0 access list allow 255.255.255.0 192.168.1

  .0 255.255.255.0

  pager lines 24

  interface ethernet0 10baset

  interface ethernet1 10full

  Outside 1500 MTU

  Within 1500 MTU

  IP address outside of *. *.198.139 255.255.255.248

  IP address inside 192.168.254.1 255.255.255.0

  alarm action IP verification of information

  alarm action attack IP audit

  location of PDM 192.168.254.10 255.255.255.255 inside

  location of PDM 192.168.1.0 255.255.255.0 outside

  history of PDM activate

  ARP timeout 14400

  Global 1 interface (outside)

  NAT (inside) 0-list of access inside_outbound_nat0_acl

  NAT (inside) 1 0.0.0.0 0.0.0.0 0 0

  Route outside 0.0.0.0 0.0.0.0 *. * 1.198.137

  Timeout xlate 03:00

  Timeout conn 0 half-closed 01:00:10: 00 udp 0:02:00 CPP 0: h323 from 10:00 0:05:00 TR

  p 0:30:00 sip_media 0:02:00

  Timeout, uauth 0:05:00 absolute

  GANYMEDE + Protocol Ganymede + AAA-server

  RADIUS Protocol RADIUS AAA server

  AAA-server local LOCAL Protocol

  Enable http server

  http 192.168.254.10 255.255.255.255 inside

  No snmp server location

  No snmp Server contact

  SNMP-Server Community public

  No trap to activate snmp Server

  enable floodguard

  Permitted connection ipsec sysopt

  No sysopt route dnat

  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

  outside_map 20 ipsec-isakmp crypto map

  card crypto outside_map 20 match address outside_cryptomap_20

  card crypto outside_map 20 peers set *. *.198.138

  outside_map crypto 20 card value transform-set ESP-3DES-SHA

  outside_map interface card crypto outside

  ISAKMP allows outside

  ISAKMP key * address *. *.198.138 netmask 255.255.255.255 No.-xauth non - co

  Nfig-mode

  part of pre authentication ISAKMP policy 20

  ISAKMP policy 20 3des encryption

  ISAKMP policy 20 chopping sha

  20 2 ISAKMP policy group

  ISAKMP duration strategy of life 20 86400

  Telnet timeout 5

  SSH timeout 5

  Terminal width 80

  PIX 2

  6.2 (2) version PIX

  ethernet0 nameif outside security0

  nameif ethernet1 inside the security100

  hostname tmaxbangor

  domain ciscopix.com

  fixup protocol ftp 21

  fixup protocol http 80

  fixup protocol h323 h225 1720

  fixup protocol h323 ras 1718-1719

  fixup protocol they 389

  fixup protocol rsh 514

  fixup protocol rtsp 554

  fixup protocol smtp 25

  fixup protocol sqlnet 1521

  fixup protocol sip 5060

  fixup protocol 2000 skinny

  names of

  permit 192.168.1.0 ip access list inside_outbound_nat0_acl 255.255.255.0 192.168

  . 254.0 255.255.255.0

  permit 192.168.1.0 ip access list outside_cryptomap_20 255.255.255.0 192.168.254

  .0 255.255.255.0

  pager lines 24

  opening of session

  debug logging in buffered memory

  interface ethernet0 10baset

  interface ethernet1 10full

  Outside 1500 MTU

  Within 1500 MTU

  IP address outside of *. *.198.138 255.255.255.248

  IP address inside 192.168.1.1 255.255.255.0

  IP verify reverse path to the outside interface

  IP verify reverse path inside interface

  the IP audit info action alarm reset drop

  reset the IP audit attack alarm drop action

  location of PDM 192.168.1.0 255.255.255.0 inside

  PDM logging 100 information

  history of PDM activate

  ARP timeout 14400

  Global 1 interface (outside)

  NAT (inside) 0-list of access inside_outbound_nat0_acl

  NAT (inside) 1 0.0.0.0 0.0.0.0 0 0

  Route outside 0.0.0.0 0.0.0.0 *. * 1.198.137

  Timeout xlate 03:00

  Timeout conn 0 half-closed 01:00:10: 00 udp 0:02:00 CPP 0: h323 from 10:00 0:05:00 TR

  p 0:30:00 sip_media 0:02:00

  Timeout, uauth 0:05:00 absolute

  GANYMEDE + Protocol Ganymede + AAA-server

  RADIUS Protocol RADIUS AAA server

  AAA-server local LOCAL Protocol

  Enable http server

  http 192.168.1.0 255.255.255.0 inside

  http 192.84.7.111 255.255.255.255 inside

  http 192.168.1.10 255.255.255.255 inside

  No snmp server location

  No snmp Server contact

  SNMP-Server Community public

  No trap to activate snmp Server

  enable floodguard

  Permitted connection ipsec sysopt

  No sysopt route dnat

  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

  outside_map 20 ipsec-isakmp crypto map

  card crypto outside_map 20 match address outside_cryptomap_20

  card crypto outside_map 20 peers set *. *.198.139

  outside_map crypto 20 card value transform-set ESP-3DES-SHA

  outside_map interface card crypto outside

  ISAKMP allows outside

  ISAKMP key * address *. *.198.139 netmask 255.255.255.255 No.-xauth non - co

  Nfig-mode

  part of pre authentication ISAKMP policy 20

  ISAKMP policy 20 3des encryption

  ISAKMP policy 20 chopping sha

  20 2 ISAKMP policy group

  ISAKMP duration strategy of life 20 86400

  Telnet 192.168.1.0 255.255.255.0 inside

  Telnet timeout 50

  SSH timeout 5

  Terminal width 80

  Can't see anything obviously wrong with the configs. You have these connected back to back on the same subnet, it looks that it even if you have xxx out IP addresses? If so it's maybe a routing problem, in what they send everything to the default gateway of xxx.x.198.137 rather than to the other.

  Try to add a static route to the remote subnet to each PIX that points directly to the peer, so on PIX1 you should have:

  Route outside 192.168.1.0 255.255.255.0 xxx.x.198.138

  and on PIX2 do:

  Route outside 192.168.254.0 255.255.255.0 xxx.x.198.139

  and see if that makes a difference. Note that you wouldn't encounter this problem when these two PIX is on separate networks and uses the default gateway for all routing decisions.

  If this still fails, run 'debug cryp isa' and ' debug cry ipsec "on the two PIX are trying to build a tunnel again, and then and send us the output.

  Also, make sure your tests that you're rattling to a host behind a PIX to a host behind the other PIX, ping PIX to PIX or host because of PIX that won't test your VPN connection.

• Access to the remote site VPN

  Hello

  I'm trying to solve a problem with the VPN, and I hope that someone could give me a helping hand.

  We have 3 offices, each with an ASA 5505 like the router/firewall, connected to a cable modem

  (NC Office) <----IPSEC----->(office of PA) <----IPSEC----->(TC Office)

  Internally, we have a full mesh VPN, so all offices can talk to each other directly.

  I have people at home, by using remote access VPN into the Office of PA, and I need them to be able to connect to two other offices there.

  I was able to run for the Office of CT, but I can't seem to work for the Office of the NC.  (I want to say is, users can remote access VPN in the PA Office and access resources in the offices of the PA and CT, but they can't get the Office of NC).

  Someone could take a look at these 2 configs and let me know if I'm missing something?  I am newer to this, so some of these configs do not have better naming conventions, but I'm getting there

  PA OFFICE

  Output of the command: "show run".

  : Saved
  :
  ASA Version 8.2 (5)
  !
  hostname WayneASA

  names of
  !
  interface Ethernet0/0
  switchport access vlan 2
  !
  interface Ethernet0/1
  !
  interface Ethernet0/2
  !
  interface Ethernet0/3
  !
  interface Ethernet0/4
  !
  interface Ethernet0/5
  !
  interface Ethernet0/6
  !
  interface Ethernet0/7
  !
  interface Vlan1
  nameif inside
  security-level 100
  IP 192.168.1.1 255.255.255.0
  !
  interface Vlan2
  nameif outside
  security-level 0
  IP 70.91.18.205 255.255.255.252
  !
  passive FTP mode
  clock timezone IS - 5
  clock to summer time EDT recurring
  DNS lookup field inside
  DNS domain-lookup outside
  DNS server-group DefaultDNS
  75.75.75.75 server name
  75.75.76.76 server name
  domain 3gtms.com
  permit same-security-traffic intra-interface
  object-group Protocol TCPUDP
  object-protocol udp
  object-tcp protocol
  inside_access_in of access allowed any ip an extended list
  IPSec_Access to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.2.0 255.255.255.0
  IPSec_Access to access extended list ip 192.168.10.0 allow 255.255.255.224 192.168.2.0 255.255.255.0
  IPSec_Access to access extended list ip 192.168.10.0 allow 255.255.255.224 192.168.5.0 255.255.255.0
  inside_nat0 to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.10.0 255.255.255.224
  inside_nat0 to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.2.0 255.255.255.0
  inside_nat0 to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.5.0 255.255.255.0
  TunnelSplit1 list standard access allowed 192.168.10.0 255.255.255.224
  TunnelSplit1 list standard access allowed 192.168.1.0 255.255.255.0
  outside_1_cryptomap to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.2.0 255.255.255.0
  outside_2_cryptomap to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.5.0 255.255.255.0
  outside_cryptomap to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.5.0 255.255.255.0
  RemoteTunnel_splitTunnelAcl list standard access allowed 192.168.1.0 255.255.255.0
  RemoteTunnel_splitTunnelAcl_1 list standard access allowed 192.168.1.0 255.255.255.0
  RemoteTunnel_splitTunnelAcl_1 list standard access allowed 192.168.2.0 255.255.255.0
  RemoteTunnel_splitTunnelAcl_1 list standard access allowed 192.168.5.0 255.255.255.0
  out_access_in list extended access udp allowed any SIP host 70.91.18.205 EQ
  out_access_in list extended access permit tcp any host 70.91.18.205 eq 5000
  out_access_in list extended access permits any udp host 70.91.18.205 range 9000-9049
  out_access_in list extended access permit tcp any host 70.91.18.205 EQ SIP
  out_access_in list extended access allowed object-group TCPUDP any host 70.91.18.205 eq 5090
  out_access_in list extended access permit udp any host 70.91.18.205 eq 5000
  Note to outside-nat0 access-list NAT0 for VPNPool to Remote Sites
  outside-nat0 extended ip 192.168.10.0 access list allow 255.255.255.224 192.168.2.0 255.255.255.0
  outside-nat0 extended ip 192.168.10.0 access list allow 255.255.255.224 192.168.5.0 255.255.255.0
  pager lines 24
  asdm of logging of information
  Within 1500 MTU
  Outside 1500 MTU
  IP mask 255.255.255.224 local pool VPNPool 192.168.10.1 - 192.168.10.30
  no failover
  ICMP unreachable rate-limit 1 burst-size 1
  don't allow no asdm history
  ARP timeout 14400
  Global 1 interface (outside)
  NAT (inside) 0-list of access inside_nat0
  NAT (inside) 1 0.0.0.0 0.0.0.0
  NAT (outside) 0-list of access outside-nat0
  inside_access_in access to the interface inside group
  Access-group out_access_in in interface outside
  Route outside 0.0.0.0 0.0.0.0 70.91.18.206 1
  Timeout xlate 03:00
  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
  timeout tcp-proxy-reassembly 0:01:00
  Floating conn timeout 0:00:00
  dynamic-access-policy-registration DfltAccessPolicy
  the ssh LOCAL console AAA authentication
  Enable http server
  http 0.0.0.0 0.0.0.0 inside
  No snmp server location
  No snmp Server contact
  Server enable SNMP traps snmp authentication linkup, linkdown cold start
  Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
  Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
  Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
  Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
  Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
  Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac
  Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac
  Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
  Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac
  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
  Crypto ipsec transform-set esp-3des esp-md5-hmac VPNTransformSet
  life crypto ipsec security association seconds 28800
  Crypto ipsec kilobytes of life - safety 4608000 association
  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set
  Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
  card crypto IPSec_map 1 corresponds to the address IPSec_Access
  card crypto IPSec_map 1 set peer 50.199.234.229
  card crypto IPSec_map 1 the transform-set VPNTransformSet value
  card crypto IPSec_map 2 corresponds to the address outside_2_cryptomap
  card crypto IPSec_map 2 set pfs Group1
  card crypto IPSec_map 2 set peer 98.101.139.210
  card crypto IPSec_map 2 the transform-set VPNTransformSet value
  card crypto IPSec_map 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
  IPSec_map interface card crypto outside
  card crypto outside_map 1 match address outside_1_cryptomap
  peer set card crypto outside_map 1 50.199.234.229
  crypto ISAKMP allow outside
  crypto ISAKMP policy 1
  preshared authentication
  3des encryption
  sha hash
  Group 2
  life 43200
  Telnet 192.168.1.0 255.255.255.0 inside
  Telnet timeout 5
  SSH 0.0.0.0 0.0.0.0 inside
  SSH timeout 60
  Console timeout 0
  management-access inside
  dhcpd outside auto_config
  !
  dhcpd address 192.168.1.100 - 192.168.1.199 inside
  dhcpd dns 75.75.75.75 75.75.76.76 interface inside
  dhcpd allow inside
  !

  a basic threat threat detection
  Statistics-list of access threat detection
  no statistical threat detection tcp-interception
  WebVPN
  internal RemoteTunnel group strategy
  attributes of Group Policy RemoteTunnel
  value of server DNS 75.75.75.75 75.75.76.76
  Protocol-tunnel-VPN IPSec
  Split-tunnel-policy tunnelspecified
  value of Split-tunnel-network-list RemoteTunnel_splitTunnelAcl_1
  dfavier vUA99P1dT3fvnDZy encrypted password username
  username dfavier attributes
  type of remote access service
  rduske vu0Zdx0n3oZWFSaX encrypted password username
  username rduske attributes
  type of remote access service
  eric 0vcSd5J/TLsFy7nU password user name encrypted privilege 15
  lestofts URsSXKLozQMSeCBk username encrypted password
  username lestofts attributes
  type of remote access service
  jpwiggins 3WyoRxmI6LZjGHZE encrypted password username
  username jpwiggins attributes
  type of remote access service
  tomleonard cQXk0RJCBtxyzZ4K encrypted password username
  username tomleonard attributes
  type of remote access service
  algobel 4AjIefFXCbu7.T9v encrypted password username
  username algobel attributes
  type of remote access service
  type tunnel-group RemoteTunnel remote access
  attributes global-tunnel-group RemoteTunnel
  address pool VPNPool
  Group Policy - by default-RemoteTunnel
  IPSec-attributes tunnel-group RemoteTunnel
  pre-shared key *.
  tunnel-group 50.199.234.229 type ipsec-l2l
  IPSec-attributes tunnel-group 50.199.234.229
  pre-shared key *.
  tunnel-group 98.101.139.210 type ipsec-l2l
  IPSec-attributes tunnel-group 98.101.139.210
  pre-shared key *.
  !
  class-map inspection_default
  match default-inspection-traffic
  !
  !
  type of policy-card inspect dns preset_dns_map
  parameters
  maximum message length automatic of customer
  message-length maximum 512
  Policy-map global_policy
  class inspection_default
  inspect the preset_dns_map dns
  inspect the ftp
  inspect h323 h225
  inspect the h323 ras
  inspect the rsh
  inspect the rtsp
  inspect esmtp
  inspect sqlnet
  inspect the skinny
  inspect sunrpc
  inspect xdmcp
  inspect the sip
  inspect the netbios
  inspect the tftp
  Review the ip options
  inspect the icmp
  inspect the pptp
  !
  global service-policy global_policy
  context of prompt hostname
  no remote anonymous reporting call
  Cryptochecksum:6d1ffe8d570d467e1ea6fd60e9457ba1
  : end

  CT OFFICE

  Output of the command: "show run".

  : Saved
  :
  ASA Version 8.2 (5)
  !
  hostname RaleighASA
  activate the encrypted password of Ml95GJgphVRqpdJ7
  2KFQnbNIdI.2KYOU encrypted passwd
  names of
  !
  interface Ethernet0/0
  switchport access vlan 2
  !
  interface Ethernet0/1
  !
  interface Ethernet0/2
  !
  interface Ethernet0/3
  !
  interface Ethernet0/4
  !
  interface Ethernet0/5
  !
  interface Ethernet0/6
  !
  interface Ethernet0/7
  !
  interface Vlan1
  nameif inside
  security-level 100
  192.168.5.1 IP address 255.255.255.0
  !
  interface Vlan2
  nameif outside
  security-level 0
  IP 98.101.139.210 255.0.0.0
  !
  passive FTP mode
  clock timezone IS - 5
  clock to summer time EDT recurring
  DNS lookup field inside
  DNS server-group DefaultDNS
  Server name 24.25.5.60
  Server name 24.25.5.61
  permit same-security-traffic intra-interface
  object-group Protocol TCPUDP
  object-protocol udp
  object-tcp protocol
  Wayne_Access to access extended list ip 192.168.5.0 allow 255.255.255.0 192.168.1.0 255.255.255.0
  Wayne_Access to access extended list ip 192.168.5.0 allow 255.255.255.0 192.168.10.0 255.255.255.0
  Shelton_Access to access extended list ip 192.168.5.0 allow 255.255.255.0 192.168.2.0 255.255.255.0
  out_access_in list extended access permit tcp any host 98.101.139.210 eq www
  out_access_in list extended access permit tcp any host 98.101.139.210 eq ftp
  out_access_in list extended access permit udp any host 98.101.139.210 eq tftp
  out_access_in list extended access udp allowed any SIP host 98.101.139.210 EQ
  out_access_in list extended access permit tcp any host 98.101.139.210 eq 5090
  out_access_in list extended access permit tcp any host 98.101.139.210 eq 2001
  out_access_in list extended access permit tcp any host 98.101.139.210 eq 5080
  out_access_in list extended access permit tcp any host 98.101.139.210 eq ssh
  out_access_in list extended access permit tcp any host 98.101.139.210 eq 81
  out_access_in list extended access permit tcp any host 98.101.139.210 eq 56774
  out_access_in list extended access permit tcp any host 98.101.139.210 eq 5000
  out_access_in list extended access permit tcp any host 98.101.139.210 eq 902
  out_access_in list extended access permit tcp any host 98.101.139.210 eq netbios-ssn
  out_access_in list extended access permit tcp any host 98.101.139.210 eq 445
  out_access_in list extended access permit tcp any host 98.101.139.210 eq https
  out_access_in list extended access allowed object-group TCPUDP any host 98.101.139.210 eq 3389
  out_access_in list extended access allowed object-group TCPUDP range guest 98.101.139.210 5480 5487
  out_access_in list extended access permits any udp host 98.101.139.210 range 9000-9050
  inside_nat0 to access extended list ip 192.168.5.0 allow 255.255.255.0 192.168.1.0 255.255.255.0
  inside_nat0 to access extended list ip 192.168.5.0 allow 255.255.255.0 192.168.2.0 255.255.255.0
  inside_nat0 to access extended list ip 192.168.5.0 allow 255.255.255.0 192.168.10.0 255.255.255.0
  pager lines 24
  asdm of logging of information
  Within 1500 MTU
  Outside 1500 MTU
  ICMP unreachable rate-limit 1 burst-size 1
  don't allow no asdm history
  ARP timeout 14400
  Global 1 interface (outside)
  NAT (inside) 0-list of access inside_nat0
  NAT (inside) 1 0.0.0.0 0.0.0.0

  Access-group out_access_in in interface outside
  Route outside 0.0.0.0 0.0.0.0 98.101.139.209 1
  Timeout xlate 03:00
  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
  timeout tcp-proxy-reassembly 0:01:00
  Floating conn timeout 0:00:00
  dynamic-access-policy-registration DfltAccessPolicy
  the ssh LOCAL console AAA authentication
  Enable http server
  http 0.0.0.0 0.0.0.0 inside
  No snmp server location
  No snmp Server contact
  Server enable SNMP traps snmp authentication linkup, linkdown cold start
  Crypto ipsec transform-set esp-3des esp-md5-hmac WayneTransform
  Crypto ipsec transform-set esp-3des esp-md5-hmac SheltonTransform
  Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac
  Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac
  Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
  Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
  Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac
  Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
  Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
  Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
  Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
  life crypto ipsec security association seconds 28800
  Crypto ipsec kilobytes of life - safety 4608000 association
  card crypto IPSec_map 1 corresponds to the address Wayne_Access
  card crypto IPSec_map 1 set pfs Group1
  card crypto IPSec_map 1 set peer 70.91.18.205
  card crypto IPSec_map 1 the transform-set WayneTransform value
  card crypto IPSec_map 2 corresponds to the address Shelton_Access
  card crypto IPSec_map 2 set pfs Group1
  card crypto IPSec_map 2 set peer 50.199.234.229
  card crypto IPSec_map 2 the transform-set SheltonTransform value
  IPSec_map interface card crypto outside
  crypto ISAKMP allow outside
  crypto ISAKMP policy 1
  preshared authentication
  3des encryption
  sha hash
  Group 2
  life 43200
  Telnet timeout 5
  SSH 0.0.0.0 0.0.0.0 inside
  SSH timeout 5
  Console timeout 0
  management-access inside
  dhcpd outside auto_config
  !
  dhcpd address 192.168.5.100 - 192.168.5.199 inside
  dhcpd dns 24.25.5.60 24.25.5.61 interface inside
  dhcpd allow inside
  !

  a basic threat threat detection
  Statistics-list of access threat detection
  no statistical threat detection tcp-interception
  WebVPN
  eric 0vcSd5J/TLsFy7nU password user name encrypted privilege 15
  tunnel-group 50.199.234.229 type ipsec-l2l
  IPSec-attributes tunnel-group 50.199.234.229
  pre-shared key *.
  tunnel-group 70.91.18.205 type ipsec-l2l
  IPSec-attributes tunnel-group 70.91.18.205
  pre-shared key *.
  !
  class-map inspection_default
  match default-inspection-traffic
  !
  !
  type of policy-card inspect dns preset_dns_map
  parameters
  maximum message length automatic of customer
  message-length maximum 512
  Policy-map global_policy
  class inspection_default
  inspect the preset_dns_map dns
  inspect the ftp
  inspect h323 h225
  inspect the h323 ras
  inspect the rsh
  inspect the rtsp
  inspect esmtp
  inspect sqlnet
  inspect the skinny
  inspect sunrpc
  inspect xdmcp
  inspect the sip
  inspect the netbios
  inspect the tftp
  Review the ip options
  inspect the icmp
  !
  global service-policy global_policy
  context of prompt hostname
  no remote anonymous reporting call
  Cryptochecksum:3d770ba9647ffdc22b3637e1e5b9a955
  : end

  Hello

  I might have found the problem.

  To be honest, I'm a little tired and concentration is difficult, especially when access between multiple device configurations. So second pair of eyes is perhaps in order.

  At the moment it seems to me that this configuration is the problem on the SITE of PA

  IPSec_Access to access extended list ip 192.168.10.0 allow 255.255.255.224 192.168.5.0 255.255.255.0

  This is an ACL that defines networks the and remote for a connection VPN L2L.

  Now, when we look at what connection VPN L2L this belong we see the following

  card crypto IPSec_map 1 corresponds to the address IPSec_Access

  card crypto IPSec_map 1 set peer 50.199.234.229

  card crypto IPSec_map 1 the transform-set VPNTransformSet value

  Now, we see that the peer IP address is 50.199.234.229. Is what site this? The IP address of the CT Site that works correctly?

  Now what that said the ACL line I mentioned more early basically is that when the 192.168.10.0 network 255.255.255.224 wants to connect to the network 192.168.5.0/24 should be sent to the CT Site. And of course, this should not be the case as we want traffic to go on the NC Site

  Also worth noting is that on the SITE of the above connection is configured with the '1' priority so it gets first compared a connection. If the VPN L2L configurations were in different order then the VPN Client connection can actually work. But it's just something that I wanted to point out. The actual resolution of the problem, of course, is to detach the configuration which is the cause of the real problem in which ASA attempts to route traffic to a completely wrong place.

  So can you remove this line ACL of the ASA of PA

  No IPSec_Access access list extended ip 192.168.10.0 allow 255.255.255.224 192.168.5.0 255.255.255.0

  Then, test the VPN Client connection NC SITE again.

  Hope that this will finally be the solution

  -Jouni

• Remote IPSec VPN - client Windows 7 and ASA 5505

  Hello

  I'm having trouble with configuring IPSec VPN with Cisco ASA 5505 and Windows 7 client native VPN remotely. My client PC Gets the VPN IP pool address and can access a remote network behind ASA, but then I lose my internet connection. I read that this should be a problem with the split tunneling, but I did as it says here and no luck.

  Windows VPN Client settings, if I uncheck "use default gateway on remote network" I have an internet connection (given that the customer is using a local gateway), but then I can't ping remote network.

  In the log, I see the warnings of this type:

  TCP connection of disassembly 256 for outside:192.168.150.1/49562 to outside:213.199.181.90/80 duration 0: 00:00 0 stream bytes is a loopback (cisco)

  I have attached my configuration file (without configuring split tunneling, I tried). If you need additional newspapers, I'll send them right away.

  Thank you for your help.

  Petar Koraca

  That's what you would have needed on versions 8.3 and earlier versions:

  permit same-security-traffic intra-interface

  Global 1 interface (outside)

  NAT (outside) 1 192.168.150.0 255.255.255.0

  However I see that you are running 8.4 so I think that all you need is this (I never did on 8.4 so it may not be accurate)

  permit same-security-traffic intra-interface

  network of the NETWORK_OBJ_192.168.150.0_24 object

  dynamic NAT interface (outdoors, outdoor)

  Give it a shot and let me know how it goes.

• Implementation of remote offices, VMware ESXi

  Hi people, I hate you bug with what he could have been asnwered before, but I couldn't find an asnwer very clear here. Any help/advice is much apprecaited. So, here's the deal:

  We plan blown full virtualization (Server + VDI) to our datacenter and 3 remote sites. Data Center (HQ) and 1 remote office are located in Europe, 1 in North America and 1 Office in Hong Kong. All remote sites are with about 5 to 10 local non computer users. HQ has about 90 users and staff. Clearly, we want to put everything in place so that it can be managed on the Wan. We will make IPsec VPN site-to-site with each remote site through Cisco ASA and ISR routers/appliences.

  In HQ, we implement the Server Blade HP (chasis c7000) of several ProLiant G7 and EMC Clariion CX4 storage.

  For remote offices, we plan to have a local server (2 CPUs) and local storage. Internet connections are good DSL, but nothing complicated. On the road, we could look at MPLS in the light of the video and voice conference, but for now it's off the table. Because we want to deploy VDI in remote offices, we want to have clones the on local servers so that they are independent of WAN. We run a file sharin, DC, print server in terms of orders OS Server mainly.

  1. How is back-up to be managed from remote desktop to virtual offices at Headquarters? You can just save changes/deltas or is it always?

  2. what type of products VMware, we need in remote offices? VSphere Standard would do for everything what we need (remote management, backup remote VM etc.)?

  3. is it possible to have remote users forwarded to use their VD through the WAN of local server failure? Software that manages this part?

  4 any other recomendatiosn or best tips in our case here?

  Thanks again for any advice you have as we are very pleased to start this, but sure looks like a lot of work... and a few uncertainties.

  Jim

  Hello

  1. How do you distribute patches and OS updates to the remote VDs via WAN?

  You can use AUVS to install packages in the comments. In this way, everything is done on the spot.

  2. with a ThinApp structure in a VDI infrastructure how do you deliver applications, their patches to remote desktop (stream or MSI or?)? You have to have ThinApp servers etc. at the remote office or what is really the best way to handle this?

  ThinApp is a bit different and has their servers for the deployment of ThinApps. I think you should transfer as you ThinApps the patch... You can ask this question in the forums ThinApp.

  3. does anyone know a really good guide to set up an "office in a box" and it deployment?

  I have unfortunately seen documents for internal use. However, ones I've seen are usually at least 1 usually 2 boxes 2U with necessary storage locally or on a NAS with at least Gigabit switch. Usually, I suggest at least 2 boxes depending on the load. Ideally something easy to carry and move... If there was a 2 or 4 blade blade chassis, which would be the ideal...

  All licenses is managed at the Headquarters Office "in a box" being shipped to the remote desktop that is almost ready to go. A few tweaks remote and viola, you have the office. Don't forget to leave you an administrative VM on a VPN tunnel to your desktop to the remote location.

  Worst case scenario involves some generic desktop computers at HQ for all applications that do not need local data.

  4. licenses for virtual desktops (VMware View) must be purchased by the local office, or by given headquarters he is managed by vCenter HQ and the fact that it is on another continent?

  It's really up to you. But if it was me I would centralize management and "Chargeback" with the Agency.

  Best regards
  Edward L. Haletky VMware communities user moderator, VMware vExpert 2009, 2010

  Now available: url = http://www.astroarch.com/wiki/index.php/VMware_Virtual_Infrastructure_Security'VMware vSphere (TM) and Virtual Infrastructure Security' [/ URL]

  Also available url = http://www.astroarch.com/wiki/index.php/VMWare_ESX_Server_in_the_Enterprise"VMWare ESX Server in the enterprise" [url]

  Blogs: url = http://www.virtualizationpractice.comvirtualization practice [/ URL] | URL = http://www.astroarch.com/blog Blue Gears [url] | URL = http://itknowledgeexchange.techtarget.com/virtualization-pro/ TechTarget [url] | URL = http://www.networkworld.com/community/haletky Global network [url]

  Podcast: url = http://www.astroarch.com/wiki/index.php/Virtualization_Security_Round_Table_Podcastvirtualization security Table round Podcast [url] | Twitter: url = http://www.twitter.com/TexiwillTexiwll [/ URL]

• AFTER VPN CONNECTED TO OFFICE VPN, PING TO A CERTAIN DESTINATION UNREACHABLE HOST BACK

  Hello!

  I have setup a connection to the vpn pptp from my home to my office.

  I've successfully connected to my office vpn.

  I can remote desktop to several server in my office, but there is that I can not remote to a pc desktop.

  When I try to ping it will return the destination unreachable host

  ping 192.168.9.50

  Impossible to reach the destination response 192.168.0.1 host

  it becomes instead of 192.168.9.50 192.168.0.1

  Can someone help with this problem?

  I really do work in this pc and I don't no how to connect there?

  I'm pretty remote desktop is allowed in this pc.

  Thank you

  GUKGUK

  The 192.168.0.1 address seems to be a gateway address.  VPN gateway may have no route to that particular system, either by design or due to oversight.  You should be facing this problem with your personal COMPUTER. Brian Tillman [MVP-Outlook]
  --------------------------------
  https://MVP.support.Microsoft.com/profile/Brian.Tillman
  If a response may help, please vote it as useful. If a response to the problem, please mark it as an answer.