Repair Windows without having to start, but with the tool of reliable micro-soft

Similar Questions

• Configuration to use windows mail for mobile and iphone without having to sign in with the user name and password each time?

  Hello, I have a windows mail account on my laptop and I also have an iphone. I registered my account companys on both laptop and iphone problem is when you configure receive it and send messages on mobile then you can not send screws iphone.

  If you set up the password for the e-mail account on your iphone, it will stop and request your username and password on your laptop.

  How is it possible to use both systems without having to login with user name and password every time?

  Hoslo

  Both could be "collision" in that they are both trying to access the mail server at the same time.  Make sure that they do not check too often.  Try to disable a device when checking with each other and see if that makes a difference.  Also with WinMail, if you have a POP3 account, make sure that under Tools | Accounts | Mail | Properties | Advanced that you have configured to leave a copy of messages on the server, so the phone can bring too, that normally it will delete messages on the server when it downloads.

  Steve

• Windows 8 will not start even with the CD after uninstalling Linux

  Hi, I am currently faced with problems with my Dell Inspiron with Windows 8 3520 is installed. I had been dual-boot it with Linux Mint for a while with no problems until I decided to go completely back using Windows for convenience.  As I had installed Linux by creating a partition I followed online guides to remove the partition on which it was found, and expand the partition holds Windows to its original size. This seemed to go off without incident, until I tried to delete Grub and got to the start of the back straight to Windows computer. I followed a couple of different guides without result and finally ran a program called Boot Repair that just make things worse. After you run the program, my computer began to start directly on a screen of recovery with the error message:

  Boot your pc configuration data is missing or contains errors
  File: \EFI\Microsoft\Boot\BCD
  Error code = 0xc000000f

  After that happened, I called Dell and pushed them to send a disk of Windows 8 for me, so I could try a clean reinstall, I thought I'll fix it. Unfortunately it allows me to boot the disk. Everytime I try (when entering the BIOS and selecting the CD drive to boot from the disc) I get a message saying missing operating system, along with various things I can provide if required, and ending in asking me to insert the bootable media in the selected drive, press which just repeated the same message again. I ' v read on various fixes online without result, most who ask me to change the CD in first priority which I can't do is not listed as an option in the menu accessed by pressing F2 BIOS. I tried to add my CD drive option, but when I click in it, instead of getting the readers of CD or something like that, I get a menu called select Media Driver with options like this:

  WDC WD10JPVT-75A1YTP - Partition 1

  the only difference between them being the partition to which they are assigned, 1, 2, 4, 5 and 6. If I press on enter on any of this that it brings me to another menu called select media with a variety of different options, which change depending on the partition that I chose, which none means nothing to me. I don't know enough to try anything more, and even people at Dell seem to be at a loss. Any help would be much appreciated because I am completely lost at this point and this is my first laptop.

  Hello

  I'm not 100% sure the disks that you actually... The drive set to restore your computer to the factory should be at least 2 or 3 DVD...

  You can reinstall windows only... which, I imagine, would solve the immediate problem.

  Delete the partition with your old windows 8 on this... Don't you say that you developed it in the first partition or something... There may be a small 300 MB partition as the first and possibly a 30 GB or more, depending on the order in which Dell installed their...

  Go by your memory as to the size of the partition that you expanded 8 Win...

  The thing with reinstalling windows just is that you do not have a Dell preinstalled stuff.

  Then you would not be able to do a full restore to factory...

  Manufacturers have made significant changes as to how it's done with Win 8... as there are now several types of Bios...

  You really can't find worse off than you are now.

• After logon Windows 7 my PC starts but displays the directed message "unable to connect to a windows service.

  Continue message "Windows does not have to connect to the System Event Notification Service service.»

  Unable to connect to the internet or home network. Cannot 'see' router, although only connected by LAN & Wireless N adapter (even if the wireless adapter has stopped working since the problem occurred).  Router is fine as I can connect the laptop to wireless internet and LAN. The PC is very slow and the glass on the toolbar icons have been replaced by the standard version. Most of the software on the PC runs but I can't access to things like the event log.

  Running SCF / Scannow. CHKDSK and made a complete analysis with Zone Alarm Extreme Security which none have discovered something wrong. I wonder if it is a virus on Board that is not windows & cannot be treated within MSDOS.  If this is the case how get Zone Alarm to sweep to the back?

  My system is 64 bit, with Intel CORE I7 clocked at 2.8 GHz, 8 GB RAM & 2x1.5TB disks in a RAID 1 (mirror) configuration.

  Any help ressemelable the problem would be appreciated

  Hi Clem,

  1. you made any hardware or software comes to the computer before the show?

  2. is the computer connected to a network domain?

  This problem occurs when a new disc is added to the system while the background services always begin.

   
  Here are some ways you can follow to resolve the problem:
   
  Method 1:
  You can check if System Event Notification Service is enabled and set to automatic.

  
  Steps to follow:

  1. click on start, select run and type services.msc

  2. scroll down until you find System Event Notification Service and make sure that it is running and set to automatic.

  Also make sure Remote Procedure Call following the same steps above.

  3. restart your computer.
   
  Method 2:
  Download and apply the patch using the link:
  The Office will not load and displayed only a black or blue background after you log on to a computer that is running Windows 7 or Windows Server 2008 R2
  http://support.Microsoft.com/kb/2590550
   
  Method 3:
  a. click the Start button.

  b. type cmd in the search text box.

  c. press Ctrl-Shift-Enter keyboard shortcut to run command as administrator prompt. Allow elevation request.

  d. type netsh winsock reset in the command line shell, and then press the Enter key.

  e. restart the computer.

   

  See also:

  Wireless and wired network problems

  http://Windows.Microsoft.com/en-in/Windows/network-connection-problem-help#network-problems=Windows-7&V1H=win8tab1&V2H=win7tab1&V3H=winvistatab1&v4h=winxptab1

   

  For assistance with Zone Alarm, publish the query in the Forum Zone Alarm.

  Reference:

  http://www.ZoneAlarm.com/security/en-us/community/user-forum-agreement.htm

   

  Hope this solves the problem. If the problem persists, you can write to us and we will be happy to help you further.

• Adobe Lightroom recording without number in series (but with the box in which it was purchased.)

  I got Adobe Lightroom as a gift about a year ago. I thought that I had it installed on my computer, but when I tried to open it a few days ago it prompted me to license and enter it again. The problem with doing this, it's that I can't find my card with the serial number. I have the boxes and some of the documents that were included, but I can't find the card with the serial number. Is it possible for Adobe to help me get my product up and running without my serial number?

  Hi Emily,.

  Please see this link:

  Quickly find your serial number

  Let me know if it helps.

  Concerning

  Megha Rawat

• Windows Vista premium edition starts only with the safe mode or safe mode with network.

  There was a low voltage or surge protector and the computer came out. System Restore does not work.

  Hi ValrieSingh

   

  1. have you tried to start in normal mode after the issuance of the power?

  2. what happens if you start in normal mode?
  3. do you get errors in normal mode?

   

  You can check results when you activate the mode low resolution. It starts Windows using your current video driver, frequency settings low resolution and refresh. You can use this mode to reset your display settings.

  See also the links below for help on the issue-
  http://Windows.Microsoft.com/en-us/Windows-Vista/start-your-computer-in-safe-mode

  http://Windows.Microsoft.com/en-us/Windows-Vista/advanced-startup-options-including-safe-mode

  I hope this helps.

• Satellite P200 - reading CD or DVD without having to start

  Hello

  Is anyway to play CD or DVD without having to start up on the P200-144

  Thank you
  Machanic

  Hello

  If the laptop comes with preinstalled Express media player that you can do. You have Express collection CD Player media with your laptop?

• Windows Vista does not start upward, with success since the closure complete

  Hello world

  I actually had this problem for a long time, but I'm just now to a point where I'm ready to take a lead in fixing it.

  I can't identify when it started, but Windows Vista does not start upward, with success of a full stop. He gets to the screen where, in general, the green bars will travel across the screen, but the green bars will not come. The screen looks dim and sits there, with the text of the copyright of Microsoft Corporation. So, after not having on the mound, I have to manually shut down the computer by holding down the power button. When I try to start again, told me to go through the Startup Repair tool. If I jump the repair, I just have to meet the same problem - a computer that will not go beyond the screen "green bar".

  So, I do the Startup Repair, and told me what I do for the restoration of the system. Windows starts normally after the restoration.

  Don't forget, this happens from a full stop. To remedy this, I just never completely shut down my computer. I left running and back just at the beginning of the day. The computer may start restart, it just may not start with a full stop.

  Given the start of repair takes, literally, around 4 or 5 hours of full stops complete, accidental or power outages are a nightmare, I am obliged to wait 5 hours to get access to the computer. Fortunately, I have my laptop.

  If someone has encountered this? I saw people talking about the loop of startup repair, but that's not the point, I have. I have yet to see any discussion of my specific problem.

  Thanks in advance!

  Hello

  4-5 hours to do a startup repair is too long.

  Often you get better results if you a using a DVD of Microsoft Vista startup repair.

  Jose how to do a startup repair, etc. using a DVD of Vista from Microsoft

  Manufacturers recovery disks normally do not have Service Options; they are normally a relocation to the factory only settings option.

  Here is the guide to repair Options using a Vista DVD from Microsoft.

  If a friend or a work acquantance of yours has one, you can borrow and use it for repairs.

  http://www.bleepingcomputer.com/tutorials/repair-Windows-with-Windows-Startup-Repair/

  Table of contents

  1. Overview of Windows Vista repair options
  2. How to perform an automatic repair of Windows Vista using Startup Repair
  3. Advanced Tools Overview
  4. Conclusion

  If you do not or can not borrow a Microsoft DVD there is a download of a file ISO of Vista Startup Repair available that you can put on a Bootable floppy to make the above startup repair and that the method is recommended by a large number of posters in these Forums.

  Unfortunately, you have to buy it.

  Here is a link to it:

  http://NeoSmart.net/blog/2011/Windows-Recovery-discs-updated-reinstated/

  See you soon.

• LAUNCH WINDOWS WITHOUT ASSISTANCE CANNOT START

  I have a Pavilion p6347c running Windows 7.  He plays very well, but, since yesterday, I am unable to run windows without pressing ESC and by selecting the manual start option.  It happened from one moment to another.  This has happened every time since the problem began.  I've removed the new software I had installed a few hours before, it crashed; but I am still unable to start windows without a manual start.  Once, just before the screen went black, I think the system was pouring out and I saw a guest who doesn't say 'NO DISC SYSTEM.'

  I tried to use the default system drive, but it did not work.  It works only when I select the first drive listed when you press ESC to start, which has a bunch of letters and numbers.

  Someone told me that it might have something to do with my BIOS which might have gotten corrupted.  Does anyone have an idea how this can be fixed?  Appreciate any assistance.

  I've tried several things, but what actually works, it of that I rebooted, press F10 to go in the BIOS, press F5 to reset the default settings of the system, then F10 to save and exit. That worked for me and my system is now Purring like kitten. Good luck.

• How can I reinstall the CC without having to start a new account after a hard drive change?

  How can I reinstall the CC without having to start a new account after a hard drive change?

  Just got my PC back from repair with a new drive installed and al, I see for the CC options for new accounts to create, I already have one so I want to reinstall my account without having to pay for a new account.  Can someone tell me how to do it please?

  Hello

  Please visit the given link to download CC: download and install Adobe Creative Cloud applications

  * Connect with your Adobe on which you have registered the product ID.

  Concerning

  Bianka Attre

• I have a CS3 for windows and I switched to a mac.  Can I get a mac version without having to pay again for the sequel

  I have a CS3 for windows and I switched to a mac.  Can I get a mac version without having to pay again for the sequel?

  N °

  Adobe offers only a platform Swap on current software: order product. Platform, language swap

  CS3 is also too old to have a "upgrade path" and is no longer sold or taken in charge by Adobe.

  You, as an owner of CS3, are eligible for a 40% discount on your first year of a subscription to creative cloud well: pricing and membership creative cloud plans | Adobe Creative Cloud

  If you don't want to go with the subscription service, Adobe still offers CS6 (4 versions of current & no longer receive updates) as a perpetual license "a time of payment/download": Creative Suite 6

• All of a sudden my 5.7 LR on win10 64-bit start fails with the error message something like "error reading from the cache of the preview... Please restart." reboot, repair, reinstall, or rename SLCache helps to repair.

  All of a sudden my 5.7 LR on win10 64-bit start fails with the error message something like "error reading from the cache of the preview... Please restart." reboot, repair, reinstall, or rename SLCache helps to repair.

  

  Hello

  Greetings!

  Close to Lightroom.
  Navigate to the location where the catalog is present (default value is within the pictures folder lightroom file)

  And delete the file previews.lrdata.

  Note: do not delete the catalog with the extension .lrcat file.

  Concerning

  Jitendra

• Starting problem with the gray screen on iMac

  Hello everyone

  I'm a bit puzzled with a problem I'm having with my iMac 27 "a model late 2009, bought in early 2010, I had built at the time with 8 GB ram, 2 TB HD and fastest i7 Quad core processor available at the time.

  I'm running El Capitan, and all wise OS is perfectly up to date.

  The other week, after a systematic restart, I have a gray screen and little else.  Another reboot and everything was "normal", so I did not concern me unduly.

  Today, after that the Mac had been idle for a time during a call, the screen fell asleep as usual (I do not SLEEP the computer itself), but during his return and touch the SPACEBAR and key "ESC", the screen remains black.

  So I made a forced shutdown and restart.

  I get the screen gray and normal startup (no other sounds) chime followed by the apple logo and the startup progress bar.  He gets to halfway through the long, and then instead of bring to the top of the login page, it's just going to a gray screen Uni.

  So I restarted in safe mode, OK and ran disk utility a couple of times - at the first crossing, he noted, there a problem with the map of partition which can cause problems starting, but on the second passes and the following, everything has been noted to be OK - and the SMART status of disk has been verified.

  After a reboot - the same question as above - of carillon, gray screen with the apple logo, progress bar and then just a gray screen.  I did another secure boot and re-run of disk utility, rebooted into recovery mode and run disk utility.  And again, no problems reported.

  Another reboot and the issue was always there.

  So this time I rebooted into recovery again mode and downloaded a new installation of El Capitan.

  Unfortunately, there is no set - it is always start on a gray screen after the startup chime, the apple logo and progress bar.

  I have also removed all my account account startup items and disconnected all USB devices.

  I'm a bit lost for what to do next to be honest!

  Is there anything else I can do software wise, at home, or is it time for the repair material re shop perhaps?

  Thank you very much for your words of wisdom and support

  Kind regards

  John... :-)

  John here again: :-)

  Just a quick update which may help to determine what the problem is: I restarted in safe mode, after the reinstallation of the operating system was unable to initialize properly - grey screen again.

  However, as I have a home network, I found that I can not connect on the network with my MacBook Pro to the iMac, see all my files user on the iMac and even copy them across to the MacBook Pro with no problems.

  Everything on the iMac is saved via Time Machine on a Western Digital Firewire HD 3to.

  I also have uncompressed manual 'straight' copies of my music, movies, documents folders, etc, for an old time Capsule, currently acting as a bridge to my ethernet network wireless, and provide additional backup for those critical files - my music for example is ripped 350 odd CD, all legally purchased in ALAC on iTunes on the iMac - which represents a couple of months of work... lol... no way I want to lose that!

  So I'm a bit of a loss.  Disk utility reported no problem with the drive... I can boot into safe mode and recovery, but normal mode 'mode '... I always get the chime, the screen with apple logo and progress of the gray bar, then goes to just a gray screen instead of the login page.

  Help!

  My beloved Einstein had a hiccup!

  All comments appreciated and thanks again - hope this extra info helps

  Kind regards

  John... :-)

• I have windows XP: what do I do with the files that won't get defragmented?

  I have windows XP: what do I do with the files that won't get defragmented?

  There are about 4300 MB of files that will not defragment.

  I tried to defrag them for months, but without success.

  These files are generally used, as a result, they get w/o defraged some users

  adjustments. Run disk clean up, go after, in run, type: cmd

  In cmd type: Defrag C:

  Once her thru, type: EXIT

  After, R.Click on "my computer", properties, Advanced tab, performance, swap file button,

  with selected C:, do not select "no paging file", click on set 2 X, close, restart the pc. Once again, XP

  go in run, type: cmd cmd type: Defrag C:

  It will take more time than before, once its type thru,: OUTPUT

  Reopen the system pagefile, click on 'letting the system manage' value set 2 X, close, agree to

  replace the new swap file, restart the pc when prompted.

  Every so often, repeat the process.

• When is windows going to solve this problem with the download of kb2538242?

  When is windows going to solve this problem with the download of kb2538242?  Whenever I turn on the computer, it downloads and installs this update.  It says it is installed but the next time I turn on the computer it downloads and installs again slow down my computer until she gets.  When I hit the kb2538242 in bing it says windows will have a fix within two weeks.  Why so long?  Isn't windows discover these things before posting updates?  I use Vista, with Intel 32-bit processor.  What can I do about this problem or I have to wait on windows.

  George,

  You must contact Microsoft, don't wait until they release the patch.

  How to get help and support for this security update

  Visit the Microsoft Solution Center and antivirus security for resources and tools to keep your PC safe and healthy.  If you have problems with the installation of the update itself, visit the Microsoft Update Support for resources and tools to keep your PC updated with the latest updates.

  For enterprise customers, support for security updates is available through your usual support contacts.

  -=-

  1. click on the "Start" button, click "All programs" and click on "Windows Update".

  2. in the left panel, click "Search for update".

  3. after receiving the results of the analysis, please click on "View available updates" under the "Install updates" button

  4 Please right- click the update (KB2538242), and then click "Hide update".

  06/19 / 1109:56: 23:00