replacement for the power button cable / stop, power LED and HDD LED

Similar Questions

• Satellite A300 - replacement for the keyboard button problem

  Satellite A300 broken my number key 3.
  Easy to fix but still Toshiba have charged me £43 to replace it with a new full keyboard.
  It is less than 6 months old and still under warranty.

  What an absolute joke, I wouldn't have another toshiba again.

  > What an absolute joke, I wouldn't have another Toshiba again.
  Well, it is your personal opinion but I agree.

  However, if you understand something about laptops so you'd know that the single button can not be replaced.
  Only the CAP can be replaced but not the button on the keyboard, and thus the entire keyboard needs to be replaced!

  In addition, the guarantee only covers hardware problems that are not caused by laptop user I n don't know why the button on your keyboard is broken (maybe you was your fault) but I think that you have contacted the ASP in your country and talked to the technician then why you didn't explain that it wasn't your fault?

  In any case, the case should be clear now

• Dell Studio 540MT does not start, green power light on, but the Start button / clear stop completely

  Looking for assistance

  Have a Dell Studio 540MT (purchased in 2009), worked great until 2 weeks ago.   After a temporary system failure would not start.    The power light itself is green fixed.   The power button on the front panel is completely released.

  I read a lot of messages and other information about a similar problem.   Therefore, I did following:

  1. unplug everything, press the power button / stop for 1 minute and retries.   without success

  2. replace the CMOS battery.  without success

  3A jumps the Green and black 20 supply connection wire pins to motherboard.  It started immediately food, fans and hard drive.   so I assumed that the PSU has been authorized.

  4 replace the motherboard with a new mobo.  Curiously, in a first time, there was no change, but after about 2 minutes, the power button was working and power system.   Everything worked so very well.   I had also completely cleaned all the dust in the chassis and radiator, fan and had applied the thermal paster as directed by Artic Silver.   I even turned off after hours of race and restarted system.  Restarted, he noted that it took a couple times by pressing the power button to make it work.   Then the 2nd day I shut down the system by a normal shutdown through Win 7 and let rest for about 10 hours.   When tried to start/turning the power on again, same problem as the original problem... at first, before light power button would show amber flashing when first pressed the power button / stop, then once I unplugged the power cord and let it sit for 1 hour, the light power button showed no light, completely and again no restarts.

  5. I ordered a new power button cord (new)... This could be the problem and replacement will fix?   Is this a known problem that power button can cause this kind of problem?

  6 or is a problem of power supply?   But you wonder why the green light of the PSU and works very well when jumping the Green and black wire on the connector 20 pin?     Before I go buy a new power supply to other suggestions?

  Is there a known issue with button / stop itself and/or PSU on Dell Studio 540 MTs?

  Yes, the front panel can cause failure to start in some models, although I don't specifically remember if the 540 has been affected by this problem. Please let me know if the replacement resolves the problem.

  ATX power supplies should work. Here are the standard components of the Dell desktop computers.

• Replacement for the preview handler host has stopped working

  When creating a shortcut which connect to the network share. It can connect to get the file and it will have the following error message:

  Replacement for the preview handler host has stopped working

  Signature of the problem:
  Problem event name: APPCRASH
  Application name: prevhost.exe
  Application version: 6.1.7600.16385
  Application timestamp: 4a5bc5ca
  Fault Module name: hooknt.dll
  Fault Module Version: 1.52.0.0
  Timestamp of Module error: 49a 20833
  Exception code: c0000005
  Exception offset: 0000b 951
  OS version: 6.1.7600.2.0.0.256.48
  Locale ID: 3081
  Additional information 1: 0a9e
  More information 2: 0a9e372d3b4ad19135b953a78882e789
  Additional information 3: 0a9e
  Additional information 4: 0a9e372d3b4ad19135b953a78882e789

  Does anyone know how to avoid it?

  Hi Ivan 2008,

  You can try the network drive mapping & check if it helps.

  Create a shortcut to (map) a network drive

  Hope the helps of information. Please post back and we do know.

  Concerning
  Joel S
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• For the power level icon is missing from my taskbar. How do I find and get it again showing the taskbar?

  For the power level icon is missing from my taskbar.  How do I find and get it again showing the taskbar?  I've tried the suggestions help and read the FAQ, but in vain.

  Hi Dee Gilles,

  Welcome to the Microsoft community. According to the description, power icon is missing from the taskbar.

  ·         Did you do changes on the computer before the show?

  I'll help you with this problem. I suggest you follow these methods.

  Method 1: Follow the steps in the article.

  Icons of programs that are pinned in the taskbar may be missing or is not correctly displayed on Windows 7 computers

  Method 2: Scan the System File Checker (SFC) to repair corrupted files.

  I hope this helps. Let us know if you need help with Windows related issues. We will be happy to help you.

• I want to replace the power supply and graphics card in my p6550z

  Hello

  I'm looking to replace my power supply (BESTEC 300 watts) and the graphics card (ati radeon hd 5450). Here is a link to the HP page with my pc: http://h10025.www1.hp.com/ewfrf/wc/product?product=4242359&lc=en&cc=us&dlc=en&lang=en&cc=us

  The card I want to put is an Amd Radeon HD 6870. And I also want to put in a block of power SUPPLY Corsair 550 Watt.

  They will work when I install them? (I'm actually a little nervous about the upgrade my power supply and graphics card since it is the first time I'm doing this) (I'm also nervous because I've heard many horror stories about upgrading an HP computer)

  Hello

  There is a small metal tab inside (guts) on some models of PC HP adds stability to food. You'll have to push the tab down to get food out.  The link below will show this tab.

  How to replace a power supply.

  How to replace a video card.

  Corsair power supply (psu) I used can be mounted with the fan facing upwards or downwards depending on where fresh air is available from. Some PC cabinets have mesh ventilation where the PSU Monte so the fan should face the ventilation mesh so that fresh air can be brought into the power supply and then exhausted at the rear. Some HP computers have slots to air ventilation through the upper edges of the flanks and in this case, the PSU is mounted to the top fan. Otherwise, the Assembly of the fan should be such that the PSU will draw air from inside the Cabinet.

• Portege R100 stoped working - the power LED flashes error codes

  I have a R100 that has suddenly stopped working.
  The power led (clear amber with the image of the power wire) flashes what appears to be an error code of 5 flashes with a long pause on the last flash, followed by 3 flashes.

  That - what it means, and where can I get a list of all codes error?

  I changed the main battery, changed the spare battery and changed supply - and again, I get the error permanently. I was not able to power the laptop at all since it started. When you press the power button / nothing happens.

  I hope someone on this forum has some information that may help you diagnose this problem. Tech support representatives Toshiba post here?

  Thanks in advance.

  Hello

  I m not a R100 owner but to me it looks like a card mother malfunction because you have already tried to exchange the battery and the AC adapter.

  In this case, the best solution would be if you go to an authorized service provider. Technicians can consult the specifications and they know what means this code I think.
  Here it s only a user to user forum and I have never seen anyone from Toshiba again.

  Anyway, here you can search for the nearest ASP:
  http://EU.computers.Toshiba-Europe.com-online decision-making supported downloads & => find an authorized service provider

  Good luck!

• Qosmio X 500 does not start and the power LED is flashing every 5 seconds

  Hello
  I need help my X 500 does not start now. I tried to launch the NB as usual and suddenly the X 500 start or even power up.

  If I press the power button / stop it makes no noise, the power LED on the button and the second power LED just bliks once and turns on and keep blinking every 5 seconds.

  I tried to:
  * Remove battery and power up with AC only
  * power only to batteries
  * remove the battery power button hold for 30 seconds and over power with AC, battery only athen

  but it did not help.

  I checked the LEDs AC & battery, but they do not blink, they are just RED, so there is no problem in battery or AC.

  No idea where could be the problem?

  Thanks for help
  Frantisek

  Hello

  The failure of RAM could be the reason for this behavior of the laptop.
  Remove the RAM modules with good modules tested and check the functionality of the laptop.
  In the case of RAM isn t the troublemaker, the motherboard could be affected.

  Good luck and share your experience with us.

• How can I map a keyboard shortcut for the reacord button in the Audio Mixer Panel?

  I was recording voiceovers in first Pro CS5 for awhile, but I would like to improve my workflow. Whenever I record take, I first press the record button (labeled B below) with the mouse and press SPACEBAR on the game with the shortcut key button. After I record audio, I hit Stop and this activates / deactivates the record off the power button at the same time. I have to then click the record button with the mouse to start the process again.

  Is it possible to map a keyboard shortcut for the record button in the audio panel so that I don't have to touch the mouse during recording of voice?

  

  There is not currently a shortcut for this. This is a good feature request, if. You can submit requests for features here.

• (Model: D6000 ac750) Only the Power LED comes on after start

  Hello

  When I turn on my router, only the power LED comes on, no other LED lights. Ive been waiting for awhile as well, switching router on and outside, from time to time but its still the same result, only power LED lights

  I think this happened because of the failure of an attempt to upgrade my modem firmware, which I clicked on another tab, stop the download. After that, the modem turned off and only the power LED came on when I switched it back on

  any help would be apperciated, thank you

  NotGTAV

  I would say that the modem can be bricked you wish to contact Netgear phone support if it is still under warranty.

  http://support.NETGEAR.com/general/contact/default.aspx

  DarrenM

• What settings should I use for the rear button focus put in place for the d5 mark 3? TIA

  5 d Mark 3

  When you press the menu button, highlight on (using the knob on the front of the camera) menu "C.Fn2: disp.» "/ Operation" orange. (it's the icon of a camera that has an index of points for a light meter below - right of the wrench, to the left of the star icon).

  Each of these menus on the 5 d III have several pages.  This is the 2nd page (the 2nd point from left to right) who has the category of "custom controls".  Note that (using the wheel on the back this time) and click on the set"" button.

  Which displays a menu showing each of the important controls on the back of the camera and what they do.  Highlight the icon for the shutter button (this modifies the behavior of a half-press) and change to 'measure and AF start' to just 'start of counting.

  "AF-ON" button (on the back of your camera) is probably already put 'measure and AF Start' (I think that this is the default factory setting).

  If you're not so much focus to enable back-button (which is probably already active) you're more "power off" the focus when the shutter button is pressed to halfway.

  Good luck

• Pagefile.sys has completely disappeared. It started when the power failed and my computer crashed.

  My pagefile.sys has completely disappeared. This all started when the power failed and my computer crashed.
  I get the message that he was away, I went to the performance and settings and tried to change custom settings & re-start.

  No matter what I do, nothing works. I lost several hours of visiting sites for tips and nothing seems to help.

  I was told when re-boots WinXP it creates the new file pagefile.sys and I should delete the pagefile.sys file may be corrupted on the C drive.

  So I put the folders to show hidden files and delete pagefile.sys. I have re-set and tried to recover with no success.

  There is now absolutely no pagefile.sys on my C drive. Anyone know how I can get back my pagefile.sys?

  I want to get my virtual memory works again?

  Thank you very much in advance!

  I'd start first with the chkdsk/r.

  Don't forget - if you have a factory installed recovery Partition, fixmbr will scan it as the Master Boot Record that written XP will equal not the MBR installed by the factory, so first run chkdsk /r (did I say that already)?

  Here are some instructions:

  http://pcsupport.about.com/od/fixtheproblem/SS/RCONSOLE.htm

  Where people have no XP bootable media, here are my instructions:

  If you have no XP bootable media (or aren't sure you have) create a bootable XP Recovery CD of Console and do not forget.

  This is not the same as recovery disks that might have come with the acquisition of the system store.

  You can make a bootable Recovery Console CD by downloading an ISO file and burn it to a CD.

  The ISO bootable image file you need to download is called:

  xp_rec_con. ISO

  Download the ISO from here:

  http://www.mediafire.com/?ueyyzfymmig

  Use a new CD and this simple and free program to burn your ISO file and create your bootable CD:

  http://www.ImgBurn.com/

  When you install ImgBurn, DO NOT install the Ask toolbar.

  Here are some instructions for ImgBurn:

  http://Forum.ImgBurn.com/index.php?showtopic=61

  It would be a good idea to test your bootable CD on a computer running.

  You may need to adjust the computer BIOS settings to use the CD-ROM drive as the first device to boot instead of the hard drive.  These adjustments are made before Windows tries to load.  If you miss it, you will need to restart the system again.

  When you start on the CD, follow the instructions:

  Press any key to boot from CD...

  Installing Windows... going to pronounce.

  Press 'R' to enter the Recovery Console.

  Select the installation that you want to access (usually 1: C:\WINDOWS)

  You may be asked to enter the password (usually empty).

  You should be in the folder C:\WINDOWS.  It's the same as the

  C:\Windows folder that you see in Solution Explorer.

  The Recovery Console allows base as file commands: copy, rename, replace, delete, chkdsk, fixboot, fixmbr, cd, etc.

  For a list of the commands in the Recovery Console, type help at the prompt of commands or read on here XP Recovery Console:

  http://www.Microsoft.com/resources/documentation/Windows/XP/all/proddocs/en-us/recovery_console_cmds.mspx?mfr=true

  A good idea before you start things must first verify the integrity of your file system by using the chkdsk command.

  In the command prompt window, run the chkdsk command on the drive where Windows is installed to try to fix any problems on the afflicted player.

  Running chkdsk is fine, even if he finds no problem.  It won't hurt anything to run it.

  Assuming your boot drive is C, run the following command:

  CHKDSK C: /r

  Let chkdsk finish to correct the problems, he could find.

  It may take a long time for chkdsk complete or they seem to be "stuck".  Be patient.  If the HARD drive led blinks always, chkdsk is something.  Keep an eye on the amount of the percentage to be sure that it is still making progress.  It may even seem to go back sometime.

  You must run chkdsk/r again until it finds no error to correct.

  Remove the CD, and then type "exit" to exit the RC and restart the computer.

  You have not to set the BIOS to boot the disk HARD since the CD won't be.

• Iusually access my mail through the mail on my keyboard button. This button has stopped working completely, and I don't know how to access my mail at all. How can I get to my email?

  Iusually access my mail through the mail on my keyboard button.  This button has stopped working completely, and I don't know how to access my mail at all.  How can I get to my email?

  Add the shortcut to the desktop Outlook for all users
  http://www.SevenForums.com/tutorials/86683-Microsoft-Outlook-desktop-shortcut-create.html
   
   
  In case you wanted to tell Outlook Express...
   
  Right click on the desktop | New | Shortcut. Navigate to "c:\program files\outlook express\msimn.exe". Click next | Click Finish.  It will be a new shortcut on the desktop.
   
   
  Once an icon on the desktop, you can drag it to the taskbar for easy access.

• Gmail button (in internet explorer) keeps having moved to the right in my taskbar when I wasn't staying on the left (that's why I first open). How can I get the taskbar buttons to stop randomly to reorganize and stay in order?

  Gmail button (in internet explorer) keeps having moved to the right in my taskbar when I want to keep it on the left (that's why I first open).  How can I get the taskbar buttons to stop randomly to reorganize and stay in order?  I'm talking about the buttons on list of my open applications and documents in Windows Vista.  The bar tasks are "locked", but the button of the window open with gmail in internet explore reappears suddenly in the good moments apparently random.

  It is in the middle part of the taskbar (what I found online so far is on the start menu, the quick launch area or area/system tray of notification, the location of the taskbar in full, either about grouping taskbar - I disabled because I would like to separate).  Can anyone help?  I don't understand why this is happening (or why microsoft would never do).

  Lock the taskbar that it prevents to be moved elsewhere on the office and maintains the different sections where they are - it does not block the tabs showing what is open where they were when they were opened.  There is no control for this function.  Maybe if you uncheck similar taskbar buttons group it will help, but I honestly don't know (and fear he won't make any difference - it may even make things worse).  This also happens to me and I was unable to find an answer.  I think that there are more than just random, but I can't telll you why he moves the legs periodically (sometimes it works fine all day and other days it happens almost immediately).  But still, there is no control for this function, so there is no way to tell him to keep a specific order or to lock an established order, once it has been created.  I suspect that it happens because the notification area icons appear and hide and new programs open and close and which changes the amount of space available and so he rearranges things so that they match and apparently does not always consider the original sequence in which the elements have been added.  Maybe if you remove the Quick Launch toolbar and then add again, the order will reset (but that I know not - probably not in the original sequence, which I doubt is logged nowhere - it did not work when I tried it).

  Unfortunately, I don't have a solution to this problem (and I spend a little time looking for even before myselff posed the question) and do not believe that there is a.  It is also unfortunate that you can't move them so they can be put back in the right order if they change.  I don't think that there is nothing wrong with your system or that it is something that can be repaired or fixed - it's just the way it is and we just have to live with it.  I don't know any 3rd party software that controls the order of tabs open in the taskbar program (but you can check out Bing, Gooogle,www.tucows.comand www.download.com to see if I'm wrong on this - here n "t all when I looked trying to solve this problem for my own system).

  I'm sorry it wasn't what you wanted to hear, but it's like that.  I don't know if it's different in Windows 7.

  Good luck!

  Lorien - MCSA/MCSE/network + / has + - if this post solves your problem, please click the 'Mark as answer' or 'Useful' button at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• After execution of the new updated Adobe, HP Elitebook 2760p left click on the touchpad button has stopped working.

  Original title: left click not working not not on HP laptop

  On my HP Elitebook 2760p running Windows 7 Pro 64 bit, left click on the touchpad button has stopped working.  The right click works, the works of pad, (scrolling and click on) it's just the left click.  It started after the execution of the new update of adobe. I tried to uninstall and reinstall the driver synaptec. I tried the mouse fast and slow speed. I tried pressing rigid, flexible, in different places. I would try to uninstall the update from Adobe, but it won't allow me.  So I uninstalled Adobe Reader and re-installed. Still nothing. Any suggestions?

  Hi cyrilmillot,

  You try to run the Adobe Reader removal tool to remove the Adobe reader completely the system software.

  See the link to Adobe to download the removal tool:

  Adobe Reader/Acrobat removal tool

  After retiring, you can check whether the left click works. If it does not, you could get in touch with Adobe support for further assistance on this topic:

  Adobe forums

  http://helpx.Adobe.com/support/

  If the problem persists, then it may be a hardware problem and you may have to contact HP support for further assistance:

  HP support

  HP laptops - use and configure the TouchPad (Windows 7 and Vista)