Replication between PS6010 and PS410 question

Similar Questions

• Z10 Bluetooth blackBerry between Z10 and PlayBook questions

  Since the upgrade of a Torch 9800 to a Z10 I problems massifs wth Bluetooth between my laptop and my Playbook. They are

  BlackBerry Bridge offers no function whatsoever

  I am unable to get my Playbook to connect to Internet via Internet Tetthering on my Z10

  I'm unable to transfer files between the two devices using Bluetooth

  My devices are paired, but only available is using my phone as a remote control for the PlayBook, wow!

  People advice? This situation is quite useless.

  I have the same problems and pursued...

  With respect to the characteristic bridge that's not finished yet developed for the Z10 to the tablet. The Bridge mode is really only good for limit navigation, but does not work well with sites secured using https.

  In the Playbook e-mail client Bridge mode will not work correctly. It works better in mode hot spot WiFi, or with the true USB tether.

  Tethering using Bluetooth does not work yet correctly with the Tablet and other types of tablets and Bluetooth connections between computers. With a laptop or desktop USB strap works great.  I use it myself with my laptop. I was told that Bluetooth attachment option be set in one of the next updates.

  The best solution is to use the phone mode hot spot WiFi for the tablet. It works very well, and it's much faster that the Bluetooth for fixing can never work. Bluetooth attachment is limited to about 2.0 to 2.5 MB/sec speed. With the hot mode the lanyard WiFi spot can go at the speed of your mobile data connection will allow. In 4G mode I got more than 21 mb/s.

  I use where possible a unit of external battery with my phone for more battery time using its WiFi access point mode. BlackBerry has this option. You can see them in Blackberry accessories at most of the places that sell Blackberry accessories.  CrackBerry.com and Futureshop sell it is incidental.

  I hope this helps you!

• VPN between ASA and cisco router [phase2 question]

  Hi all

  I have a problem with IPSEC VPN between ASA and cisco router

  I think that there is a problem in the phase 2

  Can you please guide me where could be the problem.
  I suspect questions ACL on the router, but I cannot fix. ACL on the router is specified below

  Looking forward for your help

  Phase 1 is like that

  Cisco_router #sh crypto isakmp his

  IPv4 Crypto ISAKMP Security Association
  status of DST CBC State conn-id slot
  78.x.x.41 87.x.x.4 QM_IDLE 2006 0 ACTIVE

  and ASA

  ASA # sh crypto isakmp his

  ITS enabled: 1
  Generate a new key SA: 0 (a tunnel report Active 1 and 1 to generate a new key during the generate a new key)
  Total SA IKE: 1

  1 peer IKE: 78.x.x.41
  Type: L2L role: initiator
  Generate a new key: no State: MM_ACTIVE

  Phase 2 on SAA

  ASA # sh crypto ipsec his
  Interface: Outside
  Tag crypto map: Outside_map, seq num: 20, local addr: 87.x.x.4

  Outside_cryptomap_20 ip 172.19.209.0 access list allow 255.255.255.0 172.
  19.194.0 255.255.255.0
  local ident (addr, mask, prot, port): (172.19.209.0/255.255.255.0/0/0)
  Remote ident (addr, mask, prot, port): (172.19.194.0/255.255.255.0/0/0)
  current_peer: 78.x.x.41

  #pkts program: 8813, #pkts encrypt: 8813, #pkts digest: 8813
  #pkts decaps: 0, #pkts decrypt: 0, #pkts check: 0
  compressed #pkts: 0, unzipped #pkts: 0
  #pkts uncompressed: 8813, model of #pkts failed: 0, #pkts Dang failed: 0
  #send errors: 0, #recv errors: 0

  local crypto endpt. : 87.x.x.4, remote Start crypto. : 78.x.x.41

  Path mtu 1500, fresh ipsec generals 58, media, mtu 1500
  current outbound SPI: C96393AB

  SAS of the esp on arrival:
  SPI: 0x3E9D820B (1050509835)
  transform: esp-3des esp-md5-hmac no
  running parameters = {L2L, Tunnel}
  slot: 0, id_conn: 7, crypto-card: Outside_map
  calendar of his: service life remaining (KB/s) key: (4275000/3025)
  Size IV: 8 bytes
  support for replay detection: Y
  outgoing esp sas:
  SPI: 0xC96393AB (3378746283)
  transform: esp-3des esp-md5-hmac no
  running parameters = {L2L, Tunnel}
  slot: 0, id_conn: 7, crypto-card: Outside_map
  calendar of his: service life remaining (KB/s) key: (4274994/3023)
  Size IV: 8 bytes
  support for replay detection: Y

  Phase 2 on cisco router

  protégé of the vrf: (none)
  local ident (addr, mask, prot, port): (172.19.209.0/255.255.255.0/0/0)
  Remote ident (addr, mask, prot, port): (172.19.194.0/255.255.255.0/0/0)
  current_peer 87.x.x.4 port 500
  LICENCE, flags is {origin_is_acl},
  #pkts program: encrypt 0, #pkts: 0, #pkts digest: 0
  #pkts decaps: 0, #pkts decrypt: 0, #pkts check: 0
  compressed #pkts: 0, unzipped #pkts: 0
  #pkts uncompressed: 0, #pkts compr. has failed: 0
  #pkts not unpacked: 0, #pkts decompress failed: 0
  Errors #send 0, #recv 0 errors

  local crypto endpt. : 78.x.x.41, remote Start crypto. : 87.x.x.4
  Path mtu 1452, ip mtu 1452, ip mtu BID Dialer0
  current outbound SPI: 0x0 (0)

  SAS of the esp on arrival:

  the arrival ah sas:

  SAS of the CFP on arrival:

  outgoing esp sas:

  outgoing ah sas:

  outgoing CFP sas:

  protégé of the vrf: (none)
  local ident (addr, mask, prot, port): (172.19.194.0/255.255.255.0/0/0)
  Remote ident (addr, mask, prot, port): (172.19.209.0/255.255.255.0/0/0)
  current_peer 87.x.x.4 port 500
  LICENCE, flags is {origin_is_acl},
  #pkts program: encrypt 0, #pkts: 0, #pkts digest: 0
  #pkts decaps: 8947, #pkts decrypt: 8947, #pkts check: 8947
  compressed #pkts: 0, unzipped #pkts: 0
  #pkts uncompressed: 0, #pkts compr. has failed: 0
  #pkts not unpacked: 0, #pkts decompress failed: 0
  Errors #send 0, #recv 0 errors

  local crypto endpt. : 78.x.x.41, remote Start crypto. : 87.x.x.4
  Path mtu 1452, ip mtu 1452, ip mtu BID Dialer0
  current outbound SPI: 0x3E9D820B (1050509835)

  SAS of the esp on arrival:
  SPI: 0xC96393AB (3378746283)
  transform: esp-3des esp-md5-hmac.
  running parameters = {Tunnel}
  Conn ID: 29, flow_id: Motorola SEC 1.0:29, card crypto: mycryptomap
  calendar of his: service life remaining (k/s) key: (4393981/1196)
  Size IV: 8 bytes
  support for replay detection: Y
  Status: ACTIVE

  the arrival ah sas:

  SAS of the CFP on arrival:

  outgoing esp sas:
  SPI: 0x3E9D820B (1050509835)
  transform: esp-3des esp-md5-hmac.
  running parameters = {Tunnel}
  Conn ID: 30, flow_id: Motorola SEC 1.0:30, card crypto: mycryptomap
  calendar of his: service life remaining (k/s) key: (4394007/1196)
  Size IV: 8 bytes
  support for replay detection: Y
  Status: ACTIVE

  outgoing ah sas:

  outgoing CFP sas:

  VPN configuration is less in cisco router

  access-list 101 permit ip 172.19.194.0 0.0.0.255 172.19.206.0 0.0.0.255 connect
  access-list 101 permit ip 172.19.206.0 0.0.0.255 172.19.194.0 0.0.0.255 connect
  access-list 101 permit ip 172.19.194.0 0.0.0.255 172.19.203.0 0.0.0.255 connect
  access-list 101 permit ip 172.19.203.0 0.0.0.255 172.19.194.0 0.0.0.255 connect
  access-list 101 permit ip 172.19.194.0 0.0.0.255 172.19.209.0 0.0.0.255 connect
  access-list 101 permit ip 172.19.209.0 0.0.0.255 172.19.194.0 0.0.0.255 connect

  access-list 105 deny ip 172.19.194.0 0.0.0.255 172.19.206.0 0.0.0.255 connect
  access-list 105 deny ip 172.19.206.0 0.0.0.255 172.19.194.0 0.0.0.255 connect
  access-list 105 deny ip 172.19.194.0 0.0.0.255 172.19.203.0 0.0.0.255 connect
  access-list 105 deny ip 172.19.203.0 0.0.0.255 172.19.194.0 0.0.0.255 connect
  access-list 105 deny ip 172.19.194.0 0.0.0.255 172.19.209.0 0.0.0.255 connect
  access-list 105 deny ip 172.19.209.0 0.0.0.255 172.19.194.0 0.0.0.255 connect

  sheep allowed 10 route map
  corresponds to the IP 105

  Crypto ipsec transform-set esp-3des esp-md5-hmac mytransformset

  mycryptomap 100 ipsec-isakmp crypto map
  the value of 87.x.x.4 peer
  Set transform-set mytransformset
  match address 101

  crypto ISAKMP policy 100
  BA 3des
  md5 hash
  preshared authentication
  Group 2
  ISAKMP crypto key xxx2011 address 87.x.x.4

  Your permit for 105 ACL statement should be down is changed to match because it is the most general ACL.

  You currently have:

  Extend the 105 IP access list
  5 permit ip 172.19.194.0 0.0.0.255 (18585 matches)
  10 deny ip 172.19.194.0 0.0.0.255 172.19.206.0 0.0.0.255 connect
  30 deny ip 172.19.194.0 0.0.0.255 172.19.203.0 0.0.0.255 connect
  50 deny ip 172.19.194.0 0.0.0.255 172.19.209.0 0.0.0.255 connect

  It should be:

  Extend the 105 IP access list
  10 deny ip 172.19.194.0 0.0.0.255 172.19.206.0 0.0.0.255 connect
  30 deny ip 172.19.194.0 0.0.0.255 172.19.203.0 0.0.0.255 connect
  50 deny ip 172.19.194.0 0.0.0.255 172.19.209.0 0.0.0.255 connect

  IP 172.19.194.0 allow 60 0.0.0.255 (18585 matches)

  To remove it and add it to the bottom:

  105 extended IP access list

  not 5

  IP 172.19.194.0 allow 60 0.0.0.255 any

  Then ' delete ip nat trans. "

  and it should work now.

• Questions about a relationship between InDesign and S1000D specification

  Hi I have a few questions about a relationship between InDesign and S1000D specification. First, InDesign does not meet an S1000D standard? If so, what questions are supported in InDesign as "S1000D issue 4.1'?." In addition, inflicts InDesign interconnected with CSDB through any creative or other module. I'm looking forward to get useful answers and thank you in advance.

  I agree with the screen name of Test in this regard. Technical publications represent only a small percentage of the market of InDesign. And it is likely that the authors of these publications InDesign may not have heard of the S1000D specification.

• LACP hash between N3048 and CISCO SG300/SG200 + question Twinax attach direct cable

  Hello

  In my network I have deployed two new N3048 with 2 transceivers SPF + and SPF module back + as core switches are connected to other 3 switches from edge of N2048 using optical fiber and I reused my previous CISCO SG300 and SG200 goes to serve the other two boxes of my campus via the spine in copper.

  I have 4 copper cable which starts from the hub of the SG300 network and 2 the SG200 brass. I set up to have a redundant connection using 2 + 2 with SG300 and 1 + 1 with SG200 RSTP.

  So for the SG300 I re LAG + LACP to have two channels of the N3048s port, but now that a single cable is connected because I don't know what kind of LACP hash mode should I put on N3048 to have a compatible hash between Dell and Cisco switches.

  My N3048 have mode 7 (Advanced hash) as default but I guess that cisco models do not understand... so, what mode is the best for LACP work perfectly with small business cisco switches?

  I also received my twinax cables to connect my two N3048 via SPF + back modules... conhot can I plug the cables into the slots SPF + (already mounted) without turning off my basic switches?

  Thank you!

  See you soon

  Cables can be connected/disconnected, but I don't know if the real module SFP + for the rear of the N3000 is hot plug.

• Replication between two servers without direct connecton

  Hi all

  In this case, we have two servers without direct access between them (firewall, security requirements). In fact the two servers are stored in different VPN.
  and the question is:
  Can you build an architecture that will provide replication between them (include the server in downstream, trails in the intermediate machine bank file, or something else)?

  Much love and thanks for your suggestions))
  

  Hello

  In this case, your downstream server should be able to communicate to your Source and target.

  Kind regards

  Veera

• Difference between 'Reload' and "Reload (Override Cache)"?

  Https://support.mozilla.org/en-US/kb/keyboard-shortcuts-perform-firefox-tasks-quickly#w_navigation, what is the difference between 'Reload' and "Reload (Override Cache)"? What makes "ignore cache"?

  Reloading Web pages and cache bypass aims to obtain a new copy of perhaps obsolete or damaged files currently stored in the disk cache.
  You can do it like the first attempt if a normal charging does not seem to provide a version of a Web site or if you are having problems with a Web site otherwise.

  We usually have advice that if you have questions:

  Reload Web pages and ignore the cache to refresh potentially stale or corrupt.

  • Hold down the SHIFT key and click the Reload button
  • Press 'Ctrl + F5' or 'Ctrl + Shift + R' (Windows, Linux)
  • Press 'Command + shift + R' (Mac)

  Clear the cache and delete cookies only from Web sites that cause problems.
  "Clear the Cache":

  • Firefox/tools > Options > advanced > network > content caching Web: 'clear now '.

  'Delete Cookies' sites causing problems:

  • Firefox/tools > Options > privacy > "Use the custom settings for history" > Cookies: "show the Cookies".

  Start Firefox in Safe Mode to check if an extension or theme (Firefox/tools > Modules > Extensions) or if hardware acceleration is the cause of the problems.

  • https://support.Mozilla.org/KB/safe+mode
  • https://support.Mozilla.org/KB/troubleshooting+extensions+and+themes

• Difference between valuation and putting in good shape?

  What is the difference between recovery and formatting?

  I need to download tools and utilities to perform the recovery?

  Recovery recovery image installation.
  Formatting of removal of content from disk HARD integer.

  No, you don't need any download. All you need is CD/DVD recovery for your laptop model.

  To be honest, your questions are a bit funny. If you want to have accurate on such things information please publish your laptop model and it will be much easier to give you exact explanation and instructions how to use recovery CD/DVDs.

• Whenever I type the letter between f and h (he can't come in here or the problem occurs, so I will use 'p' instead), the locking of the keyboard and an informal search screen is displayed in the toolbar. Also happeninp in emails and 'my documents' but no

  I can't use a certain letter on my keyboard when in Firefox, email or my documents without the Freezin' screen and a pop up appears in my toolbar for a brousin site. The character I can not type is the letter between f and h in the alphabet. I have no problem with this letter in other applications, so I know that's not the keyboard. How to make and use this letter?

  This has happened

  Don't know how many times

  Is a week by o

  Start Firefox in Firefox to solve the issues in Safe Mode to check if one of your modules is causing your problem (switch to the DEFAULT theme: Tools > Modules > themes).
  See the extensions, themes and problems of hardware acceleration to resolve common troubleshooting Firefox problems and troubleshooting questions with plugins like Flash or Java to solve common Firefox problems

  If this does not work in safe mode and then disable all your extensions and then try to find out who is causing by allowing both the problem reappears.
  You can use 'Disable all add-ons' on the start safe mode window.
  You will need to close and restart Firefox after each change through "file > exit" (on Mac: "Firefox > Quit")

• Browse catalyst prepared - export between inside and outside as in the catalyst?

  Hello world

  Dear people of Sony, is possible to add a feature to export / trasncoding files between In and Out marks only as in catalyst go? Was surprised not to find, very handy when there is a large file that has two or more WB settings required, to export part of the file with the parameters a, marking the section with inside and outside and then adjusting those yet to export the or other parts of the shooting with an another WB settings?

  I know there is a feature to copy sections of the files ' between inside and outside "only but it would have been more convenient to have it as in catalyst browse my humble OPINION."

  Or is there a simpler workflow that I'm missing out on?

  See you soon

  Max

  P.S. Thanks to solve the strange Maj WB problem that I reported earlier, Travis and team, I have since reinstalled catalyst prepare 2015 and in awe of the capabilities of the software. Great job.

  Hi maximdryginsony:

  Thanks for the question.

  I think the function of catalyst to prepare that can solve your problem is a subset of creation. What you can do is put an In/Out point with a WB setting, and then click Log. Create a subclip (see screenshot). This will create a subelement with the color settings.

  

  -Travis

• Switching between microphone and line-in in the Realltek Sound Manager

  Ok.
  Now I know where the Realtek Sound Manager, and I can control the parameters of the microphone and speakers.
  But how can I switch between microphone and line-in?
  At the moment I don't see a line of component option snap at all. Is it because it's a kind of auto detect and the opportunity every time I connect something?
  Everyone knows this, or has some experience in this regard?
  Cordially in advance
  Frans

  Sorry but I don't understand what exactly you want.
  You have built in mic or you can use the external microphone connected to the mic-in port.
  When the external microphone is connected a resident will be disabled.

  The question is: what do you want exactly and for what purposes? Please explain what is the reason for this switching between mic and line-in port?

• Portege 4000 conflict between WiFi and Bluetooth on Windows 2000

  I recently replaced XP with Win2000 on my Toshiba Portege 4000. I also downloaded the latest drivers from the Toshiba site, using pref to Win2000 and Portege 4000.

  When you start the Bluetooth Stack V4.00.30 he wiped out the wireless LAN feature. I know that it is not possible to use Bluetooth and wireless at the same time.

  However, it is a permanent disability. During the uninstallation of the Bluetooth stack V4.00.30, wireless comes back to life.
  Is there someone who has a fix to this problem?

  Thank you!

  Hello

  Just a question: can use you the FN + F8 key combination to switch between WiFi and BT connection?

  AFAIK it's between possible and turn on both devices at the same time. In this case, he's shown great caution with content to follow:

  Devices Bluetooth and WirelessLAN function in the same radio frequency range and may interfere with each other. If you use Bluetooth devices and WirelessLAN simultaneously, you can sometimes meet optimal network performance or even lose your network connection. In this case, always stop a Bluetooth connection or your WirelessLAN

  As I said using the FN + F8 key combination, you should be able to switch between WiFi and BT connection.

• Localhost UDP connection between FCR and Matlab

  Hi all

  I have a question about the connection between Matlab and FCR UDP. My idea is to Exchange data between Matlab and Labview on the same computer.

  So I found the 'UDP Simple' of the FCR 2.0 sample project where periodically a datasample is generated randomly and sent to the remoteport 61557 local host. In the project a 'fractional number of string for transmission' is used for the transmission of data. The receiver of the sample project reads from the same port to receive the datasample.

  Now, I'm interested to read this simple stream from Matlab (just at first), however, it does not work and I'm not sure why. What I do in Matlab is the following (code Matlab)

  delete variables;
  u = udp ('127.0.0.1', 61557); % Of installation UDP Object
  fopen (u); open reading port %
  A = fread (u, 1);  % read an element
  fclose (u);

  With this code, however, I get a timeout by saying: "' WARNING: unsuccessful reading: the amount of data specified has not been returned within the time limit." "

  I'm not sure why this happens, maybe you could help me out here? I guess that the formet serving to VCF is not the same as in Matlab? Maybe the Terminators are not the same?

  See you soon,.

  Steve0

  Hey

  So, regarding the problem actually, I found the solution today. It was not the firewall, but a simple configuration in Matlab seting the UDP port. So the side of Matlab, to change the definition of udp object according to

  u = udp ('127.0.0.1', 'Thelocalport', 61557);

  If you have

  u = udp ('127.0.0.1', 'Thelocalport', 61557);
  fopen (u);

  A = fread (u)

  fclose (u);
  Delete (u);

  Who does the trick and you can read from the port. Then of course you say Matlab that you read from the "LocalPort" x, which I wasn't aware of.

  On the transmitter side, you simply:

  u = udp ('127.0.0.1', 61557);

  fopen (u);

  fwrite (u, '1');

  fclose (u);
  Delete (u);

  Here, you set just the port of transmiting.

  About the format of the data: I used the simple UDP protocol streaming Comms project where a random number is generated as a double, transformed into a string (ASCII values) and transmitted. At the level of the receiver, you get as much the UDP packet with the ASCII values that you must turn if you want to find the number.

  I hope this helps anyone having the same problem.

  See you soon

• Passing variables between LabVIEW and TestStand

  Hello

  I'm just learning how to use TestStand and although there are a multitude of resources available, I always find me at a loss on how to pass variables between TS and LV, leaving me to think that there is one fundamental thing that I'm missing which is likely, given that I have a weeks experience with LabVIEW and a days of experience with TestStand.

  I took a glance to the example of 'Clusters' to the Code Modules in TestStand examples (I use TS 2016 if it matters) because I thought it would be quite ideal for what I hope. In this case, I hope to be able to pass a string (a file path) to LabVIEW and VI power take this string and use it as part of an order for the Exec.VI system.  Then, I would be able to pass strings back to TestStand to show the user if an error occurred, but I thought I should get the first part of work.

  I guess my question is what do I have to wait to see in clusters to the example of the Modules of Code? The Watch window displays all defined variables premise on which has the ContainerOut in the Variables pane, but I don't see any kind of update on facades (VI1.vi and VI2.vi) LabVIEW code. Should I be?

  I looked at a few other discussions of the forum here and here, as well as the document of the basis of knowledge here, but could not recreate their solutions. It seems that the connector pane would be a viable way to go, but I'm not sure on how we create and use effectively. According to this document , it makes it seem like it should be simple enough to makes these terminals, but I am still missing a key step. I was able to follow all the steps on the knowledge base document and run the sequence, but then had no idea if it worked or not; I have the report show me the values of the variables I put, but I have no idea whether or not he actually did anything with the LabVIEW VI, or how I could see that.

  Please let me know if you need further information or clarifaction everything I ask.

  Thank you for your time,
  JColvin

  Digilent, a company of National Instruments

  If you want to enter values, you must create a vi for instance dialog box

  

  

  The OK button will allow new values to pass to the output terminals.

  A Cancel button will pass just the original through the output values without alteration. The VI will close when either the OK button or cancel were pressed.

  Concerning

  Ray

• What is the difference between AXIEM and EMSIght? What are the benefits of AXIEM by EMSight if any?

  I wonder what are the differences between AXIEM and EMSight. Are associated with application? One is better than the other? Please explain.

  AWR estimated AXIEM most powerful plan EM Simulator around.   AXIEM is at the center of continuous research and improvement, while EMSight is only worked on if revealed serious flaws.  Here is a summary of the differences:

  Mesh

  • EMSight must mesh the nearest grid drivers using rectangles.  This causes the mesh to have more elements mesh when there are small and large geometries.  The grid should be small enough to capture the small geometry but then causes large geometries to mesh more.   In addition, angled or curved structures causes inefficiencies mesh.
  
  
  • AXIEM STS forms, rather than a grid.  In addition, the mesh can be rectangle or triangle.   This allows a much more efficient mesh.   AXIEM generally have a much more efficient
  
  
  • AXIEM contains the ability to process forms to clean geometries that cause inefficiencies of the mesh.  EMSight does not have this feature.
  
  
  • AXIEM can forms thick metal mesh, EMSight can not, and user must make approximations when thick metal will change coupling (loss is recorded properly with the thickness of the metal)

  Ports

  • The ports are for the most part similar, but parasites due on AXIEM ports are less.  In addition, the AXIEM has a side wall, thus the effects of not move of the terms of reference of the edge of the line are a lot less AXIEM in.
  
  
  • Ports can be added to most any place in geometry with AXIEM.  For EMSight, the ports are usually only added outside the geometry and have limitations to the aircraft on either side of the reference speaker.

  Problem solvers

  • EMSight does not have a low frequency Solver.  Stop low-frequency and then extrapolate to DC.  This usually works well, but you must take into account if the extrapolation is accurate.  AXIEM presents both a low and high frequency Solver so will do better in a low frequencies generally much better in DC.
  
  
  • Solver of EMSight scales O (n) ^ 2 for memory and O (n) ^ 3 for the moment.   It has a special algorithm to break the question of memory, but the question of time is the killer.  AXIEM has a direct Solver which scales in the same way and an iterative Solver which will scale O (nlogn).   In other words, AXIEM can solve a lot of bigger problems than EMSight.
  
  
  • Several AXIEM processes are multithreaded as EMSight.

  Speaker

  • EMSight is inside a perfect driver side wall.   This works well if you the circuit is in the same cavity.  If not, you must know the rules of them on to the forms of space of the flanks and how that much to extend the port could reference planes.   AXIEM is not here.   AXIEM does not currently have to simulate a perfect driver side wall.

  I don't know that I missed a few aspects of the tools.   From the point of view of the AWR that AXIEM is the tool of choice, except in a few cases have been EMSight may be required.