Reset the on-board controller Yoga 13

Similar Questions

• In some situations, you might need to reset the System Management Controller (SMC your computer)

  I was advised to do this periodically as good 'household.

  All advice appreciated.

  El Capitan

  10.11.3 (15 D 21)

  Mac (27 inches, at the end of 2013)

  3.4 GHz Intel Core i5

  12 GB 1600 MHz DDR3

  NVIDIA GeForce GTX 775M 2048 MB

  Resetting the SMC is for troubleshooting. No maintenance.

  Apple support page...

  Before resetting the SMC

  You should only do an SMC reset, after trying all the other standard troubleshooting. Try each of the following steps in this order before resetting the SMC. Test the issue after performing each step of troubleshooting to see if the problem persists.

• My IBM R40 useless after the on-board controller update!

  
  
  

• pls help me to reset the password on the Board in my atom mini hp intel CNU9244BN4

  pls help me to reset the password on the Board in my atom mini hp intel CNU9244BN4

  Hangs.

  Check your other post.

  REO

• How to replace the logic board MacBook Pro mid-2010

  I have a MacBook Pro 13-inch mid-2010. About once a week, monitors (one who is part of the laptop) and an external will turn grey and freeze. When I turned off the computer, it brings back me to the login screen (I'm under 10.11.5), but I can't move the pointer (whether with my Apple Wireless Mouse or trackpad) to select the icon for my login. After a few reboots, the computer takes care of the password reset function. And there, I can reuse the mouse, select Restart the machine, and I'm back on my way.

  The genius of Apple and I suspect that the problem is with the logic board. Unfortunately, Apple has more parts for MacBook Pro mid-2010. I contacted a few service centers certified Apple the kind told me; None of them can help either.

  Any suggestions for how I have a fix for this problem? Thank you!

  You could contact a specialist to see what their requirement is to send you the

  computer while for a diagnosis appropriate; a specialist is the one who can do all the

  works internally and could actually fix the edge logic that the Mac came with.

  I know some who do this; they charge more than a parts Exchange hosting.

  You can see what a company such as wegenermedia can do. Or see what the

  iFixit guide for Mac (for your specific model) said repair and watch to see who

  part numbers are involved in replacement of the like-kind in refurbished or tested

  OK, from sources such as powerbookmedic.com and other sources used parts.

  The logic board may not be a problem; might be some on the Board of directors or of one which

  attached to, such as the graphics processor. These older models are not

  so difficult for a specialist expert set. While the Mac is able to do so, is a good time

  for they provide labour expertise to swap upgrade replacement parts.

  They can test the feature set and should provide a guarantee for employment.

  Some of these companies repairs also restored the supply of older computers they fixed.

  Good luck & happy computing!

• Reset the SMC on Macbook Pro mid-2014

  I try to reset the controller management system on my 15 "Macbook Pro mid-2014.

  Reset the management system (SCM) controller on your Mac - Apple Support

  If the battery is good behaviour

  1. turn off the Mac.

  2. plug the MagSafe or USB - C adapter to a power source and to your Mac.

  3. using the built-in keyboard, press shift-control-Option on the left side of the keyboard, then press the power button at the same time.

  4. release all buttons, then press the power button to turn on your Mac

  In step 3, press all 4 buttons (simultaneously), and consider this a while pressed. However, the Macbook starts at.

  Even if I press the 4 keys briefly (simultaneously), launching the Mac.

  I suspect that the MSC has not been reset.

  I did something wrong?

  The MagSafe adapter is connected? You use SHIFT-control-Option on the side LEFT of the keyboard. This is important.

  Why are reset you the SMC? Is there a problem with the computer? If you are having keyboard problems, then there are chances that the keyboard does not use precisely the keys that you press. The computer must be turned off all the time, and the MagSafe will (in general) briefly change colors when you release the keys.

• How to reset the SMC on mid 2011 mini

  Do I have to remove the battery to reset the SMC on a mini mid 2011?

  Thank you

  John

  N ° see:

  MacIntel: Reset of the controller (SMC) system management

• Satellite L - How do I reset the BIOS?

  Hello

  Does anyone know how to access the greyed zones in the BIOS, you have a newspaper as 'Master' or 'Controller' first? or something?

  And nobody knows how to reset the BIOS, so I can remove the password and how to access the BIOS supervisor not only a user?

  See you soon

  Hello

  I think the gray options BIOS means you are not logged in as supervisor. You must enter the supervisor password, and then you should be able to change these options.

  And the BIOS reset is only possible from an authorized service. Ask a technician for this. They can help you!

  Welcome them

• Reset the program in MainStage 3.2.3 numbers

  Hello!

  I use the latest version of MainStage on the latest version of Mac OS X El captain as well.

  I'm having a problem when I want to reset the progressive values program change numbers.

  The real function in the works of MainStage, but once the program changes have been reassigned, MainStage is unresponsive to changes in my controller patch.

  If I manually change the program numbers, MainStage then responds.

  In the midi window, I can see that the patch change information are sent to the MainStage but without some form of response from the program.

  Anyone else having this problem?

  How can I report it to apple?

  Best regards

  I can't help you with the problem you are having, but you can provide your feedback directly to Apple via the menu drop down Mainstage. They can or not to respond, but all feedback is apparently verified; I was contacted twice over the last 6 years after the filing of comments on bugs.

• How to reset the BIOS on Satellite A100-237 password?

  Hi, guys.

  Suddenly, I ended up having a bios password problem without putting a whole. I can´t seem to start my computer A100-237, because he wants a password just after I ve it starts.

  Unfortunately I don't have haven´t had the time to go to the nearest Service partner because it is 400km away. Can someone help me solve the problem (I ve read about KeyDisk, but I need a disk to be able to use it and I simply Dona´t have a).

  Maybe I can use a kind of bootable CD to reset the password or something else?

  Thank´s in advance for your help!

  No, no, no you can not make yourself the BIOS password is not easy to remove on the desktop PC by removing the RTC battery.
  Something like that is not possible on the Toshiba laptop and can damage the Board.

  The only way to remove the BIOS password is in contact with the ASP in your country.
  I think that it of a security option because before you remove the BIOS password, you have to show the invoice or delivery note.

• reset the counter - 6601

  Hello

  I use a Board 6601 and the C++ interface.

  My configuration:

  I'm counting permanently impulses, where I'm using a sample clock to get samples of each time the sample clock transitions from low to high.

  My problem:

  I would like to reset the meter every time the sample clock is down to the great transition, as I avoid all overhead (check the number of samples and by subtracting the previous current).

  I would be very grateful for some advice on this subject.

  see you soon

  Rolf N.

  Wouldn't be enough simply to define a measurement period task buffer?  You could designate the 5 kHz clock as a basis for your time and heart rate as a signal whose duration shall be measured.  You can set you care to respond to which edge of the heart rate signal, and the material would take care of resetting the number internally on each new benefit of heartbeat signal.  For an easier interpretation of the result, read the value of count U32 form and/or units value = "Ticks" in the configuration of the task.

  -Kevin P.

• reset the encoder position different stepper

  I have a step by step (with encoder) engine connected to a NI 7350 motion controller. The encoder and the stepper have different number per revolution.

  I am trying to reset the engine to a zero position, count value is different for the stepper and encoder, with the Position.vi 'reset' under the control of the path, but it seems that I can only put them on the same value. How is it?

  -ray

  You have the option to add a secondary feedback.

  However, you can read next article.  As long as you set the parameters in MAX, he should be able to do the calculations in the background with respect to the commands that you send to the engine.  And then by setting the value of the primary feedback is not really a problem.

  For example let's say that we use the example in the article (1000 steps/rev and counts/rev encoder 2000) you start at position 0, provide an order of 100, it will make the 2:1 calculation and stop the drive motor once it has 200 impulses of the encoder.  Let's say you want to make of this new 'home' position, set you to 0 and from there.  If you set it to 0, say 150, which corresponds to 150 steps the engine or 300 counts of the encoder.

  In summary if you set the account/rev and steps/rev, Max the associated values order you will be in terms of engines.  LabVIEW will make the calculation of the rate required to stop on the County of appropriate encoder.

• Application of F1 / reset the date and time

  OK could not hang out long so here my problem feel free to move it if you must.

  Hi everyone I'm new here and I'm looking for the answer to what should be a simple question, but I can't find the answer, anywhere, not even after much research on the internet.

  My problem.  I woke up in a constant demand press F1 at the start and I had to constantly reset the date and time. A friend told me that he knew the solution and he replaced the battery Cmos and during one period of time applications of F1 and the need to reset the date and time on start arrested. Then, after a few weeks the F1 ask on startup and delivery to reset the date and time again.

  The situation at the present time, is that I replaced battery comos with the same type and the F1 started queries rearrested again. But once again after a few weeks the demand of the f1 and the need to reset the date and the tooth is distributed.

  I wonder if my friend used the bad battery when he replaced everything first, can someone out there please tell me the correct Cmos battery number and size, I need to motherboard below.

  Acer Apaire E380-CB7L mother board HT 2000 MCP6PM - Re3v:1.0 AM A what is battery correct Cmos?

  I found my answer in a response to another thread. It seems that some how the bad battery had been mounted and in my ignorance of this I still once mounted battery hurt it then compounded the problem further.

  It seems that the CMOS battery on the motherboard usually is a CR 2032 3V , I now nested together for my MB. I'll let you know if it works.

  BTW thanks to the person who advises I took on it.

• Vista does not recognize the mass storage controller driver

  How can I get microsoft to recognize their own software and files show as my controller driver of mass in diagnostic checks and updates storage?

  * original title - BUG not installed mass storage controller driver *.

  I don't really understand your question. The mass storage controller driver is available from the website of your computer mftr. (if you have a machine of brand OEM like HP, Dell, etc.) and is included in the card mother/chipset drivers OR you would get the driver from site of the card mother mftr. If you have a generic construction machine. You don't want to update these drivers from Microsoft Windows Update in all cases. If you installed Windows 7 and that you have not installed these drivers, this is your next step.

  General information on the drivers:

  Never get the drivers from Windows Update. Bring:

  1. site of the device mftr. ; OR
  2. site of the card mother mftr. If the material is on board; OR
  3. website of the OEM manufacturer for your specific machine if you have a PC OEM (HP, Dell, Sony, etc.).

  Read the installation instructions on the Web site where you get the drivers.

  To find out what hardware is in your computer:

  1. read all documentation that you got when you purchased the computer.
  2. If the computer is OEM, access the site Web of the OEM for your specific model machine and look at the specs (you'll be there to get the drivers anyway)
  3. download, install and run a program of inventory of the free system like Belarc Advisor or System Information for Windows.

  http://www.belarc.com/free_download.html - Belarc Advisor
  http://www.gtopala.com/ - System Information for Windows

  MS - MVP - Elephant Boy computers - don't panic!

• Reset the BIOS when there is no jumpers

  My Compaq Presario SR1050NX freezes on the BIOS boot screen. It looks exactly like this request:

  http://h30434.www3.HP.com/T5/desktop-lockups-freezes-hangs/computer-will-not-boot-past-BIOS-screen-C...

  When the start screen comes on, I have a few seconds in which the buttins nin lock and caps lock on the keyboard will activate the lights on the keyboard. I also CAN press the F1 key and says "Enter Setup" but freezes immediately.

  One problem is the motherboard has labels for three riders, but one is missing. They say "Clear password" they say "Clear battery" and a "Clear CMOS". However, the last one doesn't have the pins of the jumper on the Board; the pins are missing. What I have to use a paperclip to connect these dots on the motherboard or the pins are not there because it other ways to try to reset the BIOS. The Council has two memory sticks, and I removed each, one at a time without result.

  HE used the jumper "reset battery" and it seemed to do. I think the VGA cable may have been loose and with the power of connected monitor to the VGA connector, which could have the problem.

  Kevin