Reset the starting position of the mouse

Similar Questions

• Speed of the mouse needs to be reset each boot

  I like my mouse set to high speed. Whenever I turned off the computer the mouse speed goes back to a slower speed setting. I need then go to the control panel and reset the mouse to fast speed.

  Hello
   
  1. What is the brand and model of the mouse?

  2 is this a desktop or laptop computer?

   

  We recommend to change the settings of the mouse in safe mode and check the result. To start the computer in safe mode, try the following steps.

  1. start your computer.

  2. tap on the F8 key continuously to get the advanced boot menu options.

  3. from the list of items, select Safe Mode and press to enter.

  4. after starting the computer on the desk, try to change the mouse settings.

  5 restart the computer and check the result.

   

  For more information about safe mode, see this link:

  http://Windows.Microsoft.com/en-us/Windows-Vista/start-your-computer-in-safe-mode

   

  Post back with the results, so that we can help you further.

   

  Kind regards

  Syed

  Answers from Microsoft supports the engineer.

• THE MOUSE HANGS AFTER COLD START. YOU WILL NEED TO REMOVE THE BATTERY TO RESET. THEN CLICK OK

  ON A COLD, AFTER A MINUTE OR TWO, START THE MOUSE FREEZES.  I HAVE TO REMOVE THE BATTERY AND REINSERT IT AND RE-BOOTING, EVERYTHING ALREADY WORKS FINE.  AN ANOTHER COLD, SAME SEQUENCE START MUST BE FOLLOWED.  THIS ALL STARTED AFTER INSTALLATION of WIN 7 hp

  Hello

  What is the brand and model of the mouse?

  I suggest you to update the drivers for the mouse on the computer and check if it helps.

  Updated a hardware driver that is not working properly

  http://Windows.Microsoft.com/en-us/Windows7/update-a-driver-for-hardware-that-isn ' t-work correctly

• Reset the app to the starting position after closing app

  Hello!

  Currently, after I close totally the application I created of DPS, (after drag you closed since the 'home' double-tap button).

  and I reopen it the application from the homepage of my iPad, it takes me again on the last page I was reading and not at application start.

  Is there something I can do to have the app reset after you leave? No matter if it resets as soon as you exit the application, or if it only resets when you close completely. It would be it.

  Thanks for any help you guys can provide!

  Karl

  There is no way to automatically reset the content after leaving the application. You can add a button or a hyperlink in your content that goes to navto://relative/reset to reset the content, but that requires intervention by the user.

  Neil

• Problem starting el capitan (sierra) - built-in keyboard and the mouse do not respond

  Hello

  I have a 2015 macbook pro (SSD 256, 16 GB of RAM last el capitan updated) with a wired problem.

  I use it mainly to a cinema monitor and I use wireless keyboard and mouse (office installation program), and of course as a stand-alone laptop when I'm not at my desk.

  When I put the laptop to sleep, everything works fine when I wake up.

  but, if I'm away from the office and I have to restart my laptop, here is the problem.

  The boot process is very very slow, there is no edge, and when I finally have the screen to unlock the safe, the keyboard and the touchpad do not react. Actually, that's not exactly true, they are so slow that they are unusable and get caught quickly, all gel. So I can't unlock and complete the boot. My laptop is unusable ;-(

  At this point, I get a message that if I forgot my password I just need to reboot by pressing the power button, and I'll be able to reset it.

  When I do this and aprΦs the dΘmarrage that more slowly than usual but ok, I get another screen with several options of problem solving. One of them is "keyboard not responding do not. When choosing this one, it asks if you want to remove safe. I tried and everything was back to normal.

  later, I delivered safe and I had the same problem again. I did the thing to be able to restart again and improved to sierra in the hope that it would disappear. However, the problem is still there.

  I thought I could try to restart my office to see if my keyboard and wireless mouse would still work. Indeed, even if responsiveness was not normal, I could unlock and fill the chest.

  I have the impression that my laptop always "believe" it is on my desk, linked to my screen (probably the reason why I don't hear the Bell) and to my wireless K & M.

  It's really annoying and I hope someone has a solution.

  Thank you very much

  best,

  Alex

  I'm having a similar problem with macOS Sierra which I didn't have with El Capitan.  I can possibly move the cursor on the power button and turn off (no), but I must be patient because the keyboard and trackpad are only for a fraction of a second, which only allows me to move the mouse slightly.  After he stop and start back up, everything is perfect until I tried another reboot, and then I'm back to the beginning.

  I tried to reinstall the operating system, reset the SMC, resetting the NVRAM, reboot in SafeMode... nothing worked so far.

• reset the encoder position different stepper

  I have a step by step (with encoder) engine connected to a NI 7350 motion controller. The encoder and the stepper have different number per revolution.

  I am trying to reset the engine to a zero position, count value is different for the stepper and encoder, with the Position.vi 'reset' under the control of the path, but it seems that I can only put them on the same value. How is it?

  -ray

  You have the option to add a secondary feedback.

  However, you can read next article.  As long as you set the parameters in MAX, he should be able to do the calculations in the background with respect to the commands that you send to the engine.  And then by setting the value of the primary feedback is not really a problem.

  For example let's say that we use the example in the article (1000 steps/rev and counts/rev encoder 2000) you start at position 0, provide an order of 100, it will make the 2:1 calculation and stop the drive motor once it has 200 impulses of the encoder.  Let's say you want to make of this new 'home' position, set you to 0 and from there.  If you set it to 0, say 150, which corresponds to 150 steps the engine or 300 counts of the encoder.

  In summary if you set the account/rev and steps/rev, Max the associated values order you will be in terms of engines.  LabVIEW will make the calculation of the rate required to stop on the County of appropriate encoder.

• How to reset the position of the window?

  Hello

  After the operating system shutdown and detach my second monitor on my laptop some applications still visible on the monitor not present the next time I start up my laptop Win7Ultimate.

  Does anyone have an idea how to solve this problem and reset the position of the application window? (Except to return to the office and connect the monitor once again) This time, it's the application: KeePass Password Safe

  Thank you for your help

  Best regards

  Emeska

  Hi Emeska

  Have you tried the applications back to the primary monitor and then close the applications from there before you detach the second monitor?

  Sort might be to open the display settings and disabling the option of multiple monitors, before you detach the second monitor. As long as this option is enabled, you will always have that 'open space' on the edge of the main screen, to accommodate the second screen.

  I hope this helps.

  Thank you for using Windows 7

  Ronnie Vernon MVP

• The mouse pointer freezes and the monitor starts flashing after startup

  Original title: mouse point frized

  Seconds after my departure from desktop windows 7, point the mouse freezing, screen starts flashing and many vertical column of the flashing spectrum cover the screen. I take the power off, turn on. This time give me the ability to run in safe mode or a few more option. I try them all, don't work.

  Hi Paulamatilde,
   
  I imagine the inconvenience that you are experiencing right now. I will help you on that.
   
  The issue you described mainly due to the incompatibility of the display driver. Please answer the following questions so that we can better help you:
  1. don't you make changes before the show?
  2. What is the brand and model of your computer?
   
  I suggest you to follow the steps mentioned below and check. Proceed to the following method if only the problem persists.

  Method 1

  Install the driver updates and check if the gets resolved. You can check the link to update the drivers.

  Updated a hardware driver that is not working properly

  http://Windows.Microsoft.com/en-us/Windows/Update-driver-hardware-ISN

  Method 2
  Download the display driver and the driver of the mouse on the computer manufacturer's Web site and
  install and then check if the problem is resolved.
   
  Method 3
  Check the clean boot issue as Clean Boot Clan have disabled all third-party programs. This way we know whether or not any third-party program is causing the problem. You can see the article mentioned below.
  How to perform a clean boot in Windows
  http://support.Microsoft.com/kb/929135
   
  Note: Note: refer to the section "How to reset the computer to start normally after a boot minimum troubleshooting" to start the computer normally.
   
  I hope this helps. Please get back to us if you need further assistance.

• Start button on the taskbar, while opening with the mouse, but works using the touch screen does not

  Windows icon on the taskbar does not bring up start page using the mouse, but will Touch. Clickable after the restart, but only for a couple of times?

  Hello

  Please contact Microsoft Community. I understand that start button on the taskbar does not not at the opening with the mouse, it works but when touch use. I've surely you will help solve this problem.

  To better understand the issue, I would need more information on your side.

  1. The problem occurs when you use another mouse?
  2. What is the number and the model of the computer and the mouse?
  3. Did you the latest changes on the computer before this problem?

  This problem might have occurred because of these reasons:

  1. Missing updates of Windows and the device driver updates.
  2. Conflict between third-party applications.
  3. Corrupt system files.

  Try the steps listed here and see if it helps:

  Method 1:

  If the problem does not occur when you use another mouse, I suggest you to download and install all Windows Update available including optional updates. You can also install the last mouse driver\Software from mouse manufacturer website and check if it helps.

  Method 2:
  If the problem occurs when you use a different mouse, I suggest to start the computer using safe mode and check if the problem occurs or not. If this isn't the case, I suggest you put the computer in a clean boot state and check if it helps.

  Step 1:
  Start the computer in Mode safe. At the start of the computer Mode safe with the minimum set of drivers and files.

  Start settings for Windows (including safe mode)
  http://Windows.Microsoft.com/en-in/Windows-8/Windows-startup-settings-including-safe-mode

  Step 2:
  If the issue happen not in Mode without failure, perform a clean boot and check. Setting the system in a clean boot state will help you determine if third-party applications or startup items are causing the problem.

  How to perform a clean boot in Windows
  http://support.Microsoft.com/kb/929135/en-us

  Note: After the clean boot troubleshooting steps, see the "How to reset the computer to start as usual after a clean boot troubleshooting" section in the link provided to return the computer to a Normal startup mode.

  Method 3:

  If the problem persists, I suggest you perform the Scan SFC (System File Checker) and check if it helps. SFC scan will search the system files corrupted on the computer and replace them.

  Use the System File Checker tool to troubleshoot missing or corrupted on Windows Vista or Windows 7 system files
  http://support.Microsoft.com/kb/929833

  Hope this information helps. Reply to the post with an up-to-date report of the issue so that we can help you further.

• How to reset the position of the scrollbar when the updating of the jsff?

  Hello

  I have a panelGridLayout that shows the horizontal scroll bar when the content does not fit the available horizontal space.

  In the panelGridLayout I have items that I can drag and drop, and after release, I'm refreshing the grid to display the new data.

  Sometimes to show the last item I have to scroll using the horizontal scroll bar. Now when I drag and drop the last element when updating of the grid, it resets the bar to scroll to the start position and it is very annoying for the user.

  How can I reset the position of the scroll bar after reloading the page.

  Here are the things I've tried:

  1. for the the jsff pageDef file has added a new custom controller class. Inside the method refreshRegion of the class controller added the java code to run a javascript method which will set 'scrollLeft' of the div of the panelGridLayout position. The javascript method is get called (since I put an alert statement in for tests), but the scroll position bar does not. If I run the same code in javascript by a button then it works fine (so no problems in the javascript method).

  2 created an outputText component and visible value = false and clientComponent = true, and the value property value to a method of beans like this #(pageFlowScope.ratingBean.getscrollBarTextValue). Inside of the get accessor method to new call to the same javascript method but no help.

  3 tried to refresh only the gridCell inside the panelGridLayout, but since the gridCell is created by a grid cell single component af:iterator is getting updated. I need all the cells of the grid to be refreshed.

  It is a very annoying problem for our users and is reviewed by our Mgmt. Any help is appreciated.

  Thank you

  Rajesh.

  I could solve this problem.

  Here is the solution.

  Using a panelGroupLayout (scroll) as the component root to display the horizontal scroll bar and to display vertical scrollbars for columns panelGridLayout inside it.

  Set the height of the components inside the panelGroupLayout based on the height of the browser.

  Gets the height of the browser javascript using the af: clientListener of type "load" for root af:document.

  Also register a listener for the resized window event that will perform the ppr and refresh the height of the components.

  When I drag and drop I update just the panelGridLayout of the child when only resets do not bar (which is shown by the parent PanelGroupLayout) scrolling position.

  To provide a specific code, if anyone is interested.

  Thank you

  Rajesh.

• Load frames are in line with the position of the mouse

  Hello.

  Look at this site:

  www.Perpendicular.tk

  This site uses javascript to display image by image. It is not a 3D model, only images are shown by mouse position regarding a.

  In actionscript, how can I do this?

  I think I need to start putting the images in frames. After, Stop(). When you click the mouse, I need to compare with the last position and check, if the direction of the mouse is not gtonextframe and UO right.

  But how can I do this speed up the system. Look at the site that the image are load faster is movement mouse is fast...

  Thank you and sorry for my English...

  to scroll through the images for the movieclip (e.g. mc) based on the mouse position x, you can use:

  paramF(mc,0,1,stage.stageWidth,mc.totalFrames);

  this.addEventListener (MouseEvent.MOUSE_MOVE, moveF);

  function moveF(e:MouseEvent):void {}

  mc.gotoAndStop (Math.round(mc.m*mouseX+mc.b));

  }

  function paramF(mc:MovieClip,x1:Number,y1:Number,x2:Number,y2:Number):void {}

  MC.m =(Y1-Y2) /(x1-x2);

  MC.b = Y1 - mc.m * x 1;

  }

• OSMF with HTTP data stream search resets the starting index...

  Hello

  I built an OSMF player that allows users to get to where they were during the recovery, but also to rub at the beginning.

  FOR EXAMPLE:

  A flow is 1 minute.

  The user starts playing in 25 seconds.

  The user can rub-5 seconds or transmit to 55 seconds.

  It works perfectly with RTMP - TimeTrait reports correctly and video is displayed correctly.

  FOR EXAMPLE:

  Start at 25 seconds, TimeTrait reports: duration = 60, current position = 25 and video display is 25.

  Seek to rewinds 5 seconds to the current duration = 60, position = 5, video display is 5.

  But...

  With the HTTP stream...

  Start at 25 seconds. TimeTrait reports: duration = 60, current position = 25 and video display is 50.

  Search rewinds 5 seconds before the beginning of the stream and give me a media full... end of the stream.

  Start at 30 seconds, TimeTrait reports length = 60, current position = 30 and the video display is 60 Yes give me a media full... end of the stream.

  It is quite clear that what is happening is that search HTTP stream reset my starting index to the point of looking as if I had started to play with:

  NetStream.play (seekPoint);

  Rather than:

  NetStream.play();

  NetStream.seek (seekPoint);

  This, I hasten to add, is a terrible problem from the point of view of my client because it means actually I can't resume content.

  Does anyone have ideas, workarounds?

  G

  After digging in OSMF code I found a SOLUTION:

  First of all, make sure you have the latest OSMF source inside your project.

  For now it is 2.0.71 (org.osmf.utils.Version).

  Go to org.osmf.net.httpstreaming.HTTPNetStream

  and make a few changes:

  1 change the line # 1441

  _initialTime = _dvrInfo! = null? _dvrInfo.StartTime: currentTime;

  TO
  

  _initialTime = _dvrInfo! = null? _dvrInfo.StartTime: (_seekTime > 0? _playStart: currentTime);

  2. change the line # 1496

  _initialTime = currentTime

  TO

  _initialTime = _seekTime > 0? _playStart: currentTime

  That's all!

  Now you can listen to MediaPlayerCapabilityChangeEvent.CAN_SEEK_CHANGE event

  and immediately.

  By the way: If you're going to find all the bugs related to this change feel free to post them here!

• I changed my homepage to Outlook. Now as soon as Firefox gets up and starts Outlook, it freezes. I can not even Firefox options to reset the.

  I had made some changes to Firefox this morning, including change the start page of Outlook. Now as soon as Firefox gets up and starts Outlook, it freezes. I can not even Firefox options to reset the.

  There are the homepage Outlook, and there is the Mail page.
  What do you use as your home page?

  Start Firefox in Safe Mode {web link} by holding down the < shift >
  (Mac options) key and then from Firefox. Is always the problem?

• TripAdvisor.ca does not answer more to the clicks of the mouse on the Web page, such as the drop-down list to disconnect. It started with the last update.

  As I downloaded the latest version of Firefox (29.0.1) I have problems with the webpage Tripadvisor.ca . The mouse may not seem to work on Web pages. For example I can't select a tab to view pictures or details of a vacation rental. Also I am not able to use the drop down menu next to my username for me to disconnect it.

  Does anyone have a solution?

  I found that after Firefox v29, a LOT of my settings and
  
  Add - ons have been changed / reset. Try this;
  Launch Firefox in Mode safe
  
  While you are in safe mode;
  
  Firefox Options > advanced > General.
  
  Find and stop using hardware acceleration.
  
  Then check ALL your settings. Browser and Add-ons. Then restart.

• Portege M780-106 - the mouse pointer position of the stylus trolling

  Question re Toshiba portege M780-106 touch screen laptop:
  We have a problem with the mouse, the position of the stylus trolling.

  This gap considerably increases the speed of the increase in movement of the stylus.
  As we had a task of monitoring with the stylus it is problematic.

  We run the task in Windows 7 using python 2.6 with mainly pygame library functions.
  Is there a way to disable the process that produces this discrepancy between stylus pointer and mouse?

  Any help much appreciated!

  Best
  Steve

  The CPU is running in performance mode? There may be a delay because the eco mode is activated, or the speed of the CPU has strangled at low speed.