ResetSys on the GPIB instruments with addresses

Similar Questions

• Read several GPIB instruments

  Hello

  I have a question of time, when I want to read the GPIB instruments at the same time (1 to 24 instruments with 2 cards GPIB - GPIB0 and GPIB1).  The user can choose the number of instruments that it will read.

  For 17 instruments chosen for example, is an array of 17 lines connected to a loop where playback GPIB is made (see TestVi and Loop.jpeg). It took about 5 seconds to get all the data.

  But if I just copy 17 times playback (configured as a falling) Vi in a simple vi as in Untitled2.vi, tool around 1.5 sec to get all the data for the same conifguration! (See without for loop.jpeg)

  How could I read as fast as in the 2 without title vi with a for loop or something else in order to allow users to set more or less instruments without copying playback Vi once the configuration has changed?

  I tried to use call a VI dynamically , but it did not work.

  Thank you for your help

  Hello Anthony,.

  You should be able to find examples in the Finder for example of NOR (help > OR Finder in LabVIEW example) by searching for the term "Asynchronous".

  In 2013, there are a few examples located in the place shown in my sceenshot.

• Connection of an instrument with GPIB-USB connection.

  I am trying to use a GPIB-USB adapter to control a unit of Source of LabView. However, I have problems my instrument drivers to recognize the GPIB address specified for the device. I have attached an image below the address specified by IO Keysight connection Expert. I am currently trying to initialized the EMS with the GPIB driver I have attached below. Because of my knowledge limited in LabView instrument control, how should I approach of collecting the correct address of GPIB and recognize it in my VI?

  Hi wyattcurtis824,

  Before we dig into the LabVIEW code, I would recommend a Test Panel of max aperture and trying to communicate with. Are you able to send orders via Keysight connection Expert or NI MAX and see the valid data?

  In addition, when you run the vi in LabVIEW, is pilot it returns an error in the error on the box? If so, what the error is?

  This shoule information help us to the root of the problem.

  Best,

• Blue screen (BSOD) and communicate with GPIB instruments

  I have a communication problem with a Pressuregenerator of PCS400 of Mory via NI-VISA. My simple application sends requests to the instrument and reads returned responses. These actions are performed in a while loop until you press the stop button on the front. The VISA-resource is initialized before the while loop and closed after leaving the loop.
  Now the problem is that the computer will work in a blue screen with the message "NMI: check / memory parity error parity." This blue screen can be caused by switching between the programwindow and another window (for example the file Explorer) - I know it sounds strange. Then the blue screen appears after about 20 seconds. The computer worked stable in the daily work with windows.

  I have already tried several things
  -Wait a while (up to 30 ms) after writing and reading of VISA-online blue screen
  -Communicate with the Agilent 34401 multimeter with the same program (but other requests of course)-online no crash!
  -Test memory on system for about 45 hours with memtest86 + -online no found error
  -Stresstest with Prime95 (product 100% of CPU load) for about 1.5 hours on windows => no crash

  Request sended:
  _PCS4\sREADING? \n
  _PCS4\sERR? \n
  _PCS4\sSTAT? \n
  _PCS4\sERR? \n

  The system is configured as follows:
  -Windows XP Professional SP3
  -LabVIEW 8.5 FDS
  -NI-VISA, NI-VISA run-time V4.2 V4.2
  OR-488. 2 V2.52
  -Adapt PCI-GPIB with 3 x Mory PCS400 Pressuregenerator (1.3 to addresses), Agilent E3641A (address 5) and Agilent 34401 connected (6 addresses)
  -Acquisition of data PCI-6052E card
  -Some RS232 (PCI) expansion cards

  Do you have any ideas of how this strange problem?

  Thank you.

  
  

• No communication with a gpib instrument

  How can I send CR and LF at the end of writing with the instrument control.

  Instead of/r/n, use \r and \n.

  You can also configure the GPIB controller to add these characters if I remember correctly (I know you can do it with LabVIEW). I don't have a GPIB interface installed and do not exactly remember the procedure, but there is an option somewhere to change what is sent with the EOI.

• problem with the addition of delivery address

  I can't add shipping address to the Japan order a photo book. He said "the information in the following areas is missing or incomplete: State value 'Chiba' was not found in the list of valid values.» I get a value any is not valid. Help, please

  Using Photos to iPhoto or Mac application?

  It is no longer possible at all to order products printed Apple using iPhoto.  Apple has stopped the service of printed products for iPhoto at the end of March.

  To get a printed iPhoto book, print it as a PDF and send the PDF file to a printing service, for example Presto Photos.

  See the link below on how to save the PDF file for printing with PrestoPhoto post by PrestoMeghan:

  Re: Re: how to export a book done in opening a similar book in pictures?

  In this discussion are also reported by kgem and Astro7x on the first experiences with this service.

  You can only order from Apple books, if you create them in Photos for Mac. And then the delivery address must be in the same country as the billing address for your AppleID.

• It is always possible to search with different search engines in the search bar and address bar?

  I used to use the address bar of Firefox to search for things on Google and the search bar to search for things on Wikipedia. The convenience, especially with the shortcuts Ctrl + L and Ctrl + K has been incredible and I don't understand why this feature would disappear so I guess that it simply was hidden without subject: config somewhere. How can I go on revenant Firefox which is previous feature?

  Note: I use the Nightly build of Firefox for 64-bit systems, if this issue must be addressed specifically to this branch of development please directly to where I can do.

  From 23 of Firefox, the address bar uses the search engine selected in your search bar.

  Assign keywords to your search engines, then the prefix of your search in the address bar query, for example

  g gingerbread recipes
  

  Google search for revenues of gingerbread.

  For more information, see the section "Key words" in the following article.

  • Use the search bar in Firefox

  If you can't stand absolutely avoid typing two extra characters, then you can try the following extension. It has not been considered by a Firefox Add-ons site editor, so use it at your own risk.

  • http://forums.mozillazine.org/viewtopic.php?p=12927143#p12927143

• Difficulty communicating with a GPIB instrument using VISA

  Hi all

  I am trying to create a Subvi allowing communication between a computer and a spectrometer to MS260i. This is an old spectrometer and can only be interfaced via GPIB or RS232. I chose to use a GPIB-USB-HS adapter to connect it to the computer. The following parameters in the NOT-MAX I would easily send commands to the spectrometer when you use the Communicator of NOR-488. 2. I have also attached a picture of a wavelength successfully query.

  

  

  However, I am unable to do a Subvi with the same settings. For example, the following VI

  

  Returns the following error

  

  Is there something that I forget? I also noticed that even if I saved the GPIB interface properties, these do come up not by default when you use the Communicator of NOR-488. 2. Indeed, I have to manually configure EOS settings every time that I reopen it tool.

  Any help would be greatly appreciated.

  Did you do a right-click on the control of the chain and select ' \'Codes display? If you do not, the stop character is not sent.

• My MSN account was blocked and the other recorded with her email address is no longer active so I can't get a verification code.

  My msn account was blocked and the other recorded with her email address is no longer active so I can't get a verification code. What should I do?

  Hi Harryjenkins,

  I suggest you to contact MSN support for assistance on this issue:

  How to contact MSN customer service

  http://support.Microsoft.com/kb/940784

  You can also visit the site mentioned below and check if it helps:

  http://windowslivehelp.com/solution.aspx?SolutionID=283b059b-d26d-41f9-ae3d-03a07afcb4ad

   

  I hope this helps.

• Connect with * address email is removed from the privacy * is blocked for one of the following reasons:

  Hi, Im Mohamed, I sigfn I http://www.hotmail.com whith my ID show this maseg

  Connect with * address email is removed from the privacy * is blocked for one of the following reasons:

  • Someone has entered the password wrong too many times.
  • If you registered for this ID through an organization, you may not be able to use the account again.

  How to unlock my mail,

  NOTE: I tried reset my password security Question, write the correct answer, then show

  This option is temporarily unavailable because incorrect information was entered too many times. Please, try another option or try again later.

  Help me pz

  PZ send the response to this ID * address email is removed from the privacy * OR * address email is removed from the privacy * very thanks.

  Hi M-GhiathDakkak,

  Your question about Hotmail he will be better answered in forum Windows Live Hotmail . Please repost your question here.

• Connect with * address email is removed from the privacy * is blocked

  There was a problem with the song in my account (* address email is removed from the privacy *) a week before. He has temporarily blocked because of some spam massages. but I had recovered the use of password reset code.
  Now, I had this massage
  Connect with * address email is removed from the privacy * is blocked

  • Someone has entered the password wrong too many times.
  • If you registered for this ID through an organization, you will not be able to use the account again

  I got the link for the reset several times and I have reset the password but whenever I try to sing in. I use to get the same massage. What can I do to recover my account. He is my school and counts deal with work. I need to return, please help me

  This forum is for posting comments on Microsoft Answers web site, not to any other technical questions.

  For me it looks like you're talking about a Windows Live ID.  Questions about who belongs in the center of Windows Live Windows Live ID Portalsolutions.

• the program associated with the creation of a virtual instrument of Lab View. Please help me

  I have a question with the program associated with the creation of a virtual instrument of Lab View. 1. creation of virtual instrument based on the NI 9401 module mounted on the chassis NI DAQ of Compaq (nor-cDAQ-9172). Creating a virtual tool should apply the following counting pulses in series of the pulse, visualization of data by means of a digital indicator, by comparing the number of impusite with a predetermined value, this value can be assigned by the user. Indicator light when you get to reach the number of pulses, the ability to reset the counter of a button on the front panel. Digital output switch when reaching the number. I hope someone can help me.

  What is your question? You have described what the program is supposed to do, but it is unclear what you're asking about. Do you need help to get started? If so, what you have gone through the tutorials of LabVIEW? You and look at the material in tutorials the NI Developer Zone Learning Center , which provides links to other materials and other. You can also take a course online for free. Have you looked through numerous examples provided with LabVIEW for data acquisition?

• my windows says that another computer is running in the same network with the same ip address, please contact

  Today morning when I opened my samsung mini, it displays a message that another computer is running on the same network with the same ip address please find a solution for this

  In most home networks where multiple devices are connected to a router, router will assign an IP address to each device (via DHCP). This method keeps usually different devices to get the same IP address, but if you restart your router, it will not address remembered that he released before it was restarted.  This condition can also occur if you manually assigned an IP address to a device located in the router's DHCP range.  If the problem is not due to manually assign an IP address, then this condition will be corrected over time.  But if you're in a hurry, you can unplug your router from the wall and stop all computing devices on it.  Then plug the router back in and bring up all your devices again one by one.

  HTH,

  JW

• How to reset the default mail program? When I click to send e-mail to a box of 'Contact us' site web or excel sheet spread with addresses e-mail, a new msn email opens.

  How to reset the default mail program? Got msn.com. Now, I went to q.com. When I click to send e-mail to a box of 'Contact us' site web or excel sheet spread with addresses e-mail, a new msn email opens. Now, I get an error message: rundll32.exe - bad Image, followed by a message the the appklication or the DLL C:\Program FIles\MSN\MSNSharedFIles\MAILMAPI. DLL is not a valid Windows image. Please check against oyur installatiion diskette. I have msn unisnstalled.

  I can access my e-mail through hotmail msn, but no linger to subscribe to msn premium.

  original title: default e-mail program

  Hi PAULKRISSEL,

  This function is not supported natively in Windows. You may may find a third of the program that will change the default to q.com.
  
  WARNING: Microsoft provides no assurance or warranty, implied or otherwise and is not responsible for the download you receive from the sites of third parties or support related to the download or the downloaded technology. If you need assistance dealing with third party technology, please contact directly the manufacturer.

• Why when I click with the left button of the mouse on the unique tool, you open the window with the other instruments?

  When I click with the left button of the mouse on the unique tool, open the window with the other instruments

  
  

  Mohito Hi, this morning, I solved the problem by trying to support. I realized that the problem was in mice, because the click rate is at its highest level, and then click the instruments was like if he did 2. I will now set the minimum speed of the clicks.

  Thank you