Resources - issue brief

Similar Questions

• Name of resource issue VISA with Hameg HMS1000

  Hello

  I have a HAMEG HMS1000 Spectrum Analyzer and I want to communicate with him using NI VISA and SCPI commands.

  First, I created a driver for my device with the information provided here: http://www.hameg.com/0.563.0.html. my device showed in under «NI-VISA USB Devices» device manager

  The problem is when I run the application NEITHER MAX I can see my camera and communicate with them using 'PANEL TEST of VISA's ', but when I switch to labview, visa resource name does not display the name of my device.

  I did something wrong? Help, please

  You should always use the driver provided by the seller.

• DAQmx resource issues

  Hello

  I am using a cDAQ 9172 with the following modules:

  9237 to measure the force

  9205 to measure another similar in

  9263 to produce an analog voltage

  9472 to control some relays.

  I started with a simple program to configure the channels and run but I get the message to one or more resources is in use.

  Attached are two images. Is one of the main VI where I get the error. The second is the Subvi, which sets up the channels.

  I only have access to one or more of the channels for single point reads/writes in the main loop.

  Any ideas what I am doing wrong?

  Thank you

  Hi Jeff,

  The cDAQ-9172 has only an engine timing by subsystem.  You try to use the 9237 and 9205 at the same time in separate tasks causing the mistake of booking.  The work around is to add the two sets of channels to the same task.  Thread just the output of the task of creation of channel in the entrance of the task on the other.  Read return data from both channels.  It seems that you do not want this, but you can always ignore data that you care to.

  Case 6 this KB describes the problem.

• IBM ServeRAID M1015 in a Lenovo D20 4158

  Is that what someone did never successfully install an IBM ServeRAID M1015 in a D20?

  The reason why I ask is that I just tried and failed. I attached the SATA drives with SFF 8087 cable and installed the adapter in a x 16 slot. When starting, I can access the WebBIOS adapter and accesses the card from Windows 7 by using the management software. So far so good.

  The problem is that the card itself does not recognize a single disc (I tried several different types/brands). Suspecting the interruption / resource issues I have disabled the Intel and Marvell card in the BIOS, updated the firmware M1015 etc... no luck.

  -What did somebody ever successfully install a M1015 in a D20? If so, what is the trick?

  Regarding the cutting of Marvell - we have three D20s in use. On each of them this adapter corrupt always any RAID sooner or later (Linux and Windows). Even after a replacement of the motherboard. As much as I love D20, the embedded RAID adapter is really a loss.

  Thanks in advance for all tips!

  I finally solved the mystery. The problem was the cable. I had three brand new cables. It seems that each of them was defective. Waiting for me who? Right now I'm running a RAID5 that shows no problems so far and works well. It corresponds to current needs. Regarding the adapter Marvell, the problem wasn't that I let go of a volume. The problem was that the data has been corrupted for no apparent reason (State SMART drives all was okay etc.). Thus, so-called if a drive fails I think the adapter to degrade a volume to not corrupt. I had the same effects with three types of different discs from different manufacturers on this map. I disabled this card now that I had a fully functional replacement (and reliable so far) with the M1015. Just make sure that your cables are ok ;-}

• Stepper motor control while reading encoder

  Hello

  I'm looking to generater a pulse train to control a parallel reading and step by step motor in the impulses of the encoder of the motor. I was able to create two distinct VI who perform these taks individually, but when I put them into a single program (as shown below) is where I run on resource issues. I think I'll have problems affecting timers my properly and that's why I'm having these problems. I use a NI 9401 to generate impulses for the controller and a 9402 train OR read in the impulses of the encoder. If possible I would bring up just using the NI 9401 for the inputs and outputs if possible. The two are connected on a backplane cDAQ 9172 NU. Any help or suggestions would be greatly appreciated on what I'm doing wrong.

  

  Thanks for the suggestion of Carmen, but I was able to understand what it was with a little help from NEITHER. The finite number of pulses of timing function requires 2 counters, so when I tried to read in the encoder data there where no meter more left on the backplane. Changing impulses continuously solved my problem. I'll take a background of most recent basket with 4 meters from the lab which should allow me to run the finite number of pulses and read data from encoder at the same time.

  Thanks again,

  Doug

• front end control hovercraft

  Dear all,

  I am doing the project for my final year on Panel engineering front hovercraft using labview. Here, I have attached my vi. Please someone go through it.

  I get a series entry and display temperature display thermometer. Problem is as soon as the series executed and displayed reading the temperature on the thermometer the thermometer displplay display goes back to 0, reading, it will not always see the result.

  suggestions needed,

  I need to set up the sensor right, left and right, which is the Ultrasonic sensors which is the present enemy near the sensor and I need dispalay the distance between the sensor and the enemy who also came from Sanchez helps labview.how to implent it.

  Please someone help me to do this work.

  Thank you and best regards,

  Sudarshan

  LabVIEW, the default 'resets' orders or the default value (zero) indicator.

  The reason why you have to put your code inside a loop is very intuitive and a knowledge of the "common sense". You must specify the computer to keep your program execution for a specified period or until you force quit. If you don't do this, your machine runs each statement once and then, period. Imagine a plane that runs a control post (the brain) code within a material, without a loop. It will run once (for a period of a few microseconds) and then your aircraft will have no brain to decide what to do. So it will crash. Millions of lives will be lost.

  The loops are necessary 'energy' to keep your active code for a while. Your code will run once, and after it is finished running, its controls and indicators back to their State natural quantity ZERO.

  Maybe it's one of the reasons for your problem. Try putting a WHILE LOOP with a FALSE Boolean constant hung with terminal condition. Or simply wire a Boolean control the State OFF. If there still is no temperature reading, or get the reading as you mentioned, then there must be a problem with the acquisition hardware that you are using to measure the temperature.

  Try to put the loop first, observe and come back here.

  An other logistics major, that you need to take care is the SUBJECT LINE. Do not mention the title of the project in which you are facing problems. You are the door problem on only a part of your overall design. Try to get to issue brief, to-the-point. For example I have a robot (General design) where I get no ultrasonic sensor data (a design offer) because Calendar and the sycnhronization is a little new to me in LabVIEW FPGA (under part of part of overall design). So my subject line would be Timing and Synchronzation ultrasonic sensor in LabVIEW FPGA.

  Kind regards

• do not show character (^) in the formula when switch to indesign

  Hello

  I work in the math book and I place the content of the Word document (which are very formula) for indesign

  but forms consist of place of performance for the character (^)

  type characters mathematical formulas and are in eps format.

  for easy review I download a part of the word document that make up this problem

  Please answer to my problem because the project is stop

  I thank.

  http://www.filedropper.com/123_23

  but I think that math type is not having a report any with this problem

  I solve this problem changing OS and real work now

  

  If math type is resource issue, don't have to count two different in one system

  Thank you all.

• Totall for a PC virtualization

  Hi all

  I'm just an ordinary PC user and I found many benefits using VMware workstation. However, I found it a bit frustrating to virtualize an operating system on another operating system due to resource issues. So is there any VMware product that virtualizes everything start upward? I know that at the level of the company, there are many products the vertilization but what about desktop users?

  Welcome to the Forums - what you are referring are the difference between hypervisors hypervisors and hosted as workstation and VMware Server bare metal as ESX and ESXi - the closest thing to what you are looking for is probably the free ESXi product that will initialize the directory in the hypervisor - which still is an enterprise-class virtualization platform

  If you find this or any other answer useful please consider awarding points marking the answer correct or useful

• Get the error about TNS from Oracle, hosted on a LINUX machine

  Hello
  
  We moved our Solaris servers Linux databases. I run a multithreaded process that creates a db that are shared by the threads connection pool. On the passage to Linx db I get the below error message
  
  [SERVERERROR] ORA-12520: TNS:listener could not find a Manager is available for the requested server type
  
  My first port of call for resolve this error has been to check tnsnames.ora and TNS_ADMIN but they are very good and then I checked the db DB some threads connected and inserted data usually error occurred when dropping the connection thread control and one other thread picks up.
  
  Later, I changed the configuration to run only a single thread, and then it works fine without any errors. I also tried the process running even with configured to create a thread during two different sessions and then a session had this error but continues.
  
  Here is the generated sqlnet.log file
  
  
  
  ***********************************************************************
  Fatal OR connect error 12520, connect to:
  (DESCRIPTION=(ADDRESS=(PROTOCOL=TCP)(HOST=MD1SILNXDB03)(PORT=1521))(CONNECT_DATA=(SERVER=DEDICATED)(SERVICE_NAME=TRO10G1)(CID=(PROGRAM=HBFCalcImputedObservationsDebug64)(HOST=md1sisun26)(USER=TROBat01)))
  
  VERSION INFORMATION:
  AMT for Solaris: release 10.2.0.4.0 - Production
  Protocol TCP/IP NT to Solaris adapter: release 10.2.0.4.0 - Production
  Time: 7 February 2012 07:50:09
  Tracing not lit.
  AMT error struct:
  NS main err in code: 12564
  AMT-12564: TNS:connection refused
  
  
  ***********************************************************************
  Fatal OR connect error 12520, connect to:
  (DESCRIPTION = (ADDRESS = (PROTOCOL = TCP)(HOST=MD1SILNXDB03) (PORT = 1521)) (CONNECT_DATA = (SERVER = DEDICATED) (SERVICE_NAME = TRO10G1) (CID = (PROGRAM = SchedulerDebug64) (HOST = md1sisun26)(USER=TROBat01)))
  
  VERSION INFORMATION:
  AMT for Solaris: release 10.2.0.4.0 - Production
  Protocol TCP/IP NT to Solaris adapter: release 10.2.0.4.0 - Production
  Time: 7 February 2012 07:50:10
  Tracing not lit.
  AMT error struct:
  NS main err in code: 12564
  AMT-12564: TNS:connection refused
  
  
  ***********************************************************************
  Fatal OR connect error 12520, connect to:
  (DESCRIPTION=(ADDRESS=(PROTOCOL=TCP)(HOST=MD1SILNXDB03)(PORT=1521))(CONNECT_DATA=(SERVER=DEDICATED)(SERVICE_NAME=TRO10G1)(CID=(PROGRAM=HBFCalcImputedObservationsDebug64)(HOST=md1sisun26)(USER=TROBat01)))
  
  VERSION INFORMATION:
  AMT for Solaris: release 10.2.0.4.0 - Production
  Protocol TCP/IP NT to Solaris adapter: release 10.2.0.4.0 - Production
  Time: 7 February 2012 07:50:10
  Tracing not lit.
  AMT error struct:
  NS main err in code: 12564
  AMT-12564: TNS:connection refused
  NS secondary err code: 0
  NT main err in code: 0
  NT secondary err code: 0
  NT OS err code: 0
  
  
  ***********************************************************************
  Fatal OR connect error 12520, connect to:
  (DESCRIPTION=(ADDRESS=(PROTOCOL=TCP)(HOST=MD1SILNXDB03)(PORT=1521))(CONNECT_DATA=(SERVER=DEDICATED)(SERVICE_NAME=TRO10G1)(CID=(PROGRAM=HBFCalcImputedObservationsDebug64)(HOST=md1sisun26)(USER=TROBat01)))
  
  VERSION INFORMATION:
  AMT for Solaris: release 10.2.0.4.0 - Production
  Protocol TCP/IP NT to Solaris adapter: release 10.2.0.4.0 - Production
  Time: 7 February 2012 07:50:11
  Tracing not lit.
  AMT error struct:
  NS main err in code: 12564
  AMT-12564: TNS:connection refused
  NS secondary err code: 0
  NT main err in code: 0
  NT secondary err code: 0
  NT OS err code: 0
  NS secondary err code: 0
  NT main err in code: 0
  NT secondary err code: 0
  NT OS err code: 0
  
  
  ***********************************************************************
  Fatal OR connect error 12520, connect to:
  (DESCRIPTION=(ADDRESS=(PROTOCOL=TCP)(HOST=MD1SILNXDB03)(PORT=1521))(CONNECT_DATA=(SERVER=DEDICATED)(SERVICE_NAME=TRO10G1)(CID=(PROGRAM=HBFCalcImputedObservationsDebug64)(HOST=md1sisun26)(USER=TROBat01)))
  
  VERSION INFORMATION:
  AMT for Solaris: release 10.2.0.4.0 - Production
  Protocol TCP/IP NT to Solaris adapter: release 10.2.0.4.0 - Production
  Time: 7 February 2012 07:50:11
  Tracing not lit.
  AMT error struct:
  NS main err in code: 12564
  AMT-12564: TNS:connection refused
  NS secondary err code: 0
  NT main err in code: 0
  NT secondary err code: 0
  NT OS err code: 0
  
  
  ***********************************************************************
  Fatal OR connect error 12520, connect to:
  (DESCRIPTION=(ADDRESS=(PROTOCOL=TCP)(HOST=MD1SILNXDB03)(PORT=1521))(CONNECT_DATA=(SERVER=DEDICATED)(SERVICE_NAME=TRO10G1)(CID=(PROGRAM=HBFCalcImputedObservationsDebug64)(HOST=md1sisun26)(USER=TROBat01)))
  
  VERSION INFORMATION:
  AMT for Solaris: release 10.2.0.4.0 - Production
  Protocol TCP/IP NT to Solaris adapter: release 10.2.0.4.0 - Production
  Time: 7 February 2012 07:50:15
  Tracing not lit.
  AMT error struct:
  NS main err in code: 12564
  AMT-12564: TNS:connection refused
  
  
  ***********************************************************************
  Fatal OR connect error 12520, connect to:
  (DESCRIPTION=(ADDRESS=(PROTOCOL=TCP)(HOST=MD1SILNXDB03)(PORT=1521))(CONNECT_DATA=(SERVER=DEDICATED)(SERVICE_NAME=TRO10G1)(CID=(PROGRAM=HBFCalcImputedObservationsDebug64)(HOST=md1sisun26)(USER=TROBat01)))
  
  VERSION INFORMATION:
  AMT for Solaris: release 10.2.0.4.0 - Production
  Protocol TCP/IP NT to Solaris adapter: release 10.2.0.4.0 - Production
  Time: 7 February 2012 07:50:16
  Tracing not lit.
  AMT error struct:
  NS main err in code: 12564
  AMT-12564: TNS:connection refused
  NS secondary err code: 0
  NT main err in code: 0
  NT secondary err code: 0
  NT OS err code: 0
  
  
  ***********************************************************************
  Fatal OR connect error 12520, connect to:
  (DESCRIPTION=(ADDRESS=(PROTOCOL=TCP)(HOST=MD1SILNXDB03)(PORT=1521))(CONNECT_DATA=(SERVER=DEDICATED)(SERVICE_NAME=TRO10G1)(CID=(PROGRAM=HBFCalcImputedObservationsDebug64)(HOST=md1sisun26)(USER=TROBat01)))
  
  VERSION INFORMATION:
  AMT for Solaris: release 10.2.0.4.0 - Production
  Protocol TCP/IP NT to Solaris adapter: release 10.2.0.4.0 - Production
  Time: 7 February 2012 07:50:16
  Tracing not lit.
  AMT error struct:
  NS main err in code: 12564
  AMT-12564: TNS:connection refused
  NS secondary err code: 0
  NT main err in code: 0
  NT secondary err code: 0
  NT OS err code: 0
  NS secondary err code: 0
  NT main err in code: 0
  NT secondary err code: 0
  NT OS err code: 0
  
  
  ***********************************************************************
  Fatal OR connect error 12520, connect to:
  (DESCRIPTION=(ADDRESS=(PROTOCOL=TCP)(HOST=MD1SILNXDB03)(PORT=1521))(CONNECT_DATA=(SERVER=DEDICATED)(SERVICE_NAME=TRO10G1)(CID=(PROGRAM=HBFCalcImputedObservationsDebug64)(HOST=md1sisun26)(USER=TROBat01)))
  
  VERSION INFORMATION:
  AMT for Solaris: release 10.2.0.4.0 - Production
  Protocol TCP/IP NT to Solaris adapter: release 10.2.0.4.0 - Production
  Time: 7 February 2012 07:50:16
  Tracing not lit.
  AMT error struct:
  NS main err in code: 12564
  AMT-12564: TNS:connection refused
  NS secondary err code: 0
  NT main err in code: 0
  NT secondary err code: 0
  NT OS err code: 0
  
  
  ***********************************************************************
  Fatal OR connect error 12520, connect to:
  (DESCRIPTION=(ADDRESS=(PROTOCOL=TCP)(HOST=MD1SILNXDB03)(PORT=1521))(CONNECT_DATA=(SERVER=DEDICATED)(SERVICE_NAME=TRO10G1)(CID=(PROGRAM=HBFCalcImputedObservationsDebug64)(HOST=md1sisun26)(USER=TROBat01)))
  
  VERSION INFORMATION:
  AMT for Solaris: release 10.2.0.4.0 - Production
  Protocol TCP/IP NT to Solaris adapter: release 10.2.0.4.0 - Production
  Time: 7 February 2012 07:50:16
  Tracing not lit.
  AMT error struct:
  NS main err in code: 12564
  AMT-12564: TNS:connection refused
  NS secondary err code: 0
  NT main err in code: 0
  NT secondary err code: 0
  NT OS err code: 0
  
  
  ***********************************************************************
  Fatal OR connect error 12520, connect to:
  (DESCRIPTION=(ADDRESS=(PROTOCOL=TCP)(HOST=MD1SILNXDB03)(PORT=1521))(CONNECT_DATA=(SERVER=DEDICATED)(SERVICE_NAME=TRO10G1)(CID=(PROGRAM=HBFCalcImputedObservationsDebug64)(HOST=md1sisun26)(USER=TROBat01)))
  
  VERSION INFORMATION:
  AMT for Solaris: release 10.2.0.4.0 - Production
  Protocol TCP/IP NT to Solaris adapter: release 10.2.0.4.0 - Production
  Time: 7 February 2012 07:50:16
  Tracing not lit.
  AMT error struct:
  NS main err in code: 12564
  AMT-12564: TNS:connection refused
  NS secondary err code: 0
  NT main err in code: 0
  NT secondary err code: 0
  NT OS err code: 0
  
  
  ***********************************************************************
  Fatal OR connect error 12520, connect to:
  (DESCRIPTION=(ADDRESS=(PROTOCOL=TCP)(HOST=MD1SILNXDB03)(PORT=1521))(CONNECT_DATA=(SERVER=DEDICATED)(SERVICE_NAME=TRO10G1)(CID=(PROGRAM=HBFCalcImputedObservationsDebug64)(HOST=md1sisun26)(USER=TROBat01)))
  
  VERSION INFORMATION:
  AMT for Solaris: release 10.2.0.4.0 - Production
  Protocol TCP/IP NT to Solaris adapter: release 10.2.0.4.0 - Production
  Time: 7 February 2012 07:50:21
  Tracing not lit.
  AMT error struct:
  NS main err in code: 12564
  AMT-12564: TNS:connection refused
  NS secondary err code: 0
  NT main err in code: 0
  NT secondary err code: 0
  NT OS err code: 0
  
  
  ***********************************************************************
  Fatal OR connect error 12520, connect to:
  (DESCRIPTION=(ADDRESS=(PROTOCOL=TCP)(HOST=MD1SILNXDB03)(PORT=1521))(CONNECT_DATA=(SERVER=DEDICATED)(SERVICE_NAME=TRO10G1)(CID=(PROGRAM=HBFCalcImputedObservationsDebug64)(HOST=md1sisun26)(USER=TROBat01)))
  
  VERSION INFORMATION:
  AMT for Solaris: release 10.2.0.4.0 - Production
  Protocol TCP/IP NT to Solaris adapter: release 10.2.0.4.0 - Production
  Time: 7 February 2012 07:50:22
  Tracing not lit.
  AMT error struct:
  NS main err in code: 12564
  AMT-12564: TNS:connection refused
  NS secondary err code: 0
  NT main err in code: 0
  NT secondary err code: 0
  NT OS err code: 0
  
  
  ***********************************************************************
  Fatal OR connect error 12520, connect to:
  (DESCRIPTION=(ADDRESS=(PROTOCOL=TCP)(HOST=MD1SILNXDB03)(PORT=1521))(CONNECT_DATA=(SERVER=DEDICATED)(SERVICE_NAME=TRO10G1)(CID=(PROGRAM=HBFCalcImputedObservationsDebug64)(HOST=md1sisun26)(USER=TROBat01)))
  
  VERSION INFORMATION:
  AMT for Solaris: release 10.2.0.4.0 - Production
  Protocol TCP/IP NT to Solaris adapter: release 10.2.0.4.0 - Production
  Time: 7 February 2012 07:50:22
  Tracing not lit.
  AMT error struct:
  NS main err in code: 12564
  AMT-12564: TNS:connection refused
  NS secondary err code: 0
  NT main err in code: 0
  NT secondary err code: 0
  NT OS err code: 0
  
  
  ***********************************************************************
  Fatal OR connect error 12520, connect to:
  (DESCRIPTION=(ADDRESS=(PROTOCOL=TCP)(HOST=MD1SILNXDB03)(PORT=1521))(CONNECT_DATA=(SERVER=DEDICATED)(SERVICE_NAME=TRO10G1)(CID=(PROGRAM=HBFCalcImputedObservationsDebug64)(HOST=md1sisun26)(USER=TROBat01)))
  
  VERSION INFORMATION:
  AMT for Solaris: release 10.2.0.4.0 - Production
  Protocol TCP/IP NT to Solaris adapter: release 10.2.0.4.0 - Production
  Time: 7 February 2012 07:50:22
  Tracing not lit.
  AMT error struct:
  NS main err in code: 12564
  AMT-12564: TNS:connection refused
  NS secondary err code: 0
  NT main err in code: 0
  NT secondary err code: 0
  NT OS err code: 0
  
  
  ***********************************************************************
  Fatal OR connect error 12520, connect to:
  (DESCRIPTION=(ADDRESS=(PROTOCOL=TCP)(HOST=MD1SILNXDB03)(PORT=1521))(CONNECT_DATA=(SERVER=DEDICATED)(SERVICE_NAME=TRO10G1)(CID=(PROGRAM=HBFCalcImputedObservationsDebug64)(HOST=md1sisun26)(USER=TROBat01)))
  
  VERSION INFORMATION:
  AMT for Solaris: release 10.2.0.4.0 - Production
  Protocol TCP/IP NT to Solaris adapter: release 10.2.0.4.0 - Production
  Time: 7 February 2012 07:50:29
  Tracing not lit.
  AMT error struct:
  NS main err in code: 12564
  AMT-12564: TNS:connection refused
  NS secondary err code: 0
  NT main err in code: 0
  NT secondary err code: 0
  NT OS err code: 0
  
  
  ***********************************************************************
  Fatal OR connect error 12520, connect to:
  (DESCRIPTION=(ADDRESS=(PROTOCOL=TCP)(HOST=MD1SILNXDB03)(PORT=1521))(CONNECT_DATA=(SERVER=DEDICATED)(SERVICE_NAME=TRO10G1)(CID=(PROGRAM=HBFCalcImputedObservationsDebug64)(HOST=md1sisun26)(USER=TROBat01)))
  
  VERSION INFORMATION:
  AMT for Solaris: release 10.2.0.4.0 - Production
  Protocol TCP/IP NT to Solaris adapter: release 10.2.0.4.0 - Production
  Time: 7 February 2012 07:50:29
  Tracing not lit.
  AMT error struct:
  NS main err in code: 12564
  AMT-12564: TNS:connection refused
  NS secondary err code: 0
  NT main err in code: 0
  NT secondary err code: 0
  NT OS err code: 0
  NS secondary err code: 0
  NT main err in code: 0
  NT secondary err code: 0
  NT OS err code: 0
  _____________________________________________________________________________________________
  
  
  Can someone here help me to solve this error.
  
  
  Thank you
  Niraj Rouault

  This could be a resource issue, check for the second error TNS-12564 on metalink, there is not a lot (but still useful) hits.

• Issue of custom resources AMPA

  [JDev 12.1.3, MAF 2.2.0 AMPA 12.1.3.2.32]

  http://www.Ateam-Oracle.com/a-team-mobile-persistence-Accelerator-release-12-1-3-2-now-available/

  Custom resources medium?

  By the foregoing, I created a custom in the screen 'Details of the resource' resource entry Wizard.

  But while the information I've entered seems to be correctly filled as a customMethod in

  persistence - mapping.xml, there is no custom method generated in my service class

  (according to my GiT, this file was not affected at all by the Wizard).

  Has anyone other that saw issue or whether there is a work around?

  Thank you

  Paul Young

  Paul,

  On the last page of the wizard, you can set generator options, one of them is a chedhkbox to regenerate the service class that is unchecked by default. Have you checked this box?

  Steven Davelaar,

  Oracle Mobile & Cloud A-team.

• Issue of booking Resource Pool

  We used vSphere for a long time and this is the first instance where we watched in the use of resource pools to manage cluster resources.  What we try to do is pool funds from several different material groups buy and then distributed in equal shares of resources between these groups, but allow others to expand beyond what their fair share guaranteed if the resources are not being used by other groups.  And if the other groups are starting to need these resources in return, we want vSphere to restore "ready" transparently resources without causing any VM power issues etc.

  I'm pretty sure resource pools set reservations equal to assignment to a specific group is the way to go here.  If I understand correctly, resource pool bookings do not behave as the reserves of the VM, and even though I had to reserve 100% of cluster across pools resources collectively, a resource pool could grow beyond its reservation as long as there was no pretense.  When the contention starts, additional resources to a pool of resources will be taken away, but only to him guaranteed booking.

  Is my understanding of this is all correct?  Am I sure can cause problems, or a better way to accomplish this task?  Thanks in advance.

  It's the way I used to teach on reservations - think a restaurant which has 100 chairs - like the power of virtual machines on they have a number of chairs that they reserved - if the virtual machine needs more chairs he will get more chairs as long that other virtual machines do not use chairs they reserved - not what happens if all the chairs are reserved - the virtual machine will be not able to come into the restaurant (power on) even if there are empty chairs - if expandable restaurants reservations are activated a call is made to the room dining upstairs (the parent pool) to see if there are chairs available - this works in the same way for memory and cpu but memory has the ability to use the by vm vmkernel swap file and continue my analogy if all chairs are so reserved and a virtual machine appears they could sit on the patio, which can make the conversation (hard affect performance).

  When a virtual machine is turned off (leave the restaurant) it will come out of his reserve make room for several virtual machines.

• Issue of Resource Pools

  I'm relatively new to the VMware Infrastructure. I read a lot of documentation available, but I'm having a hard time getting my head around Resource Pools. I was wondering if someone could point me to documentation that includes examples of how and why the Resource Pools are used in a real production environment. In the meantime, if anyone could answer the following questions, I would appreciate it:

  It seems to me that the RPs have been created to distribute resources according to how many resources needs of an organizational unit. For example if a unit is in need of 5 machines running at 2 mhz each with 2 GB of ram, then a suitable unexapandable PR for this unit would include 10 mhz and 10 gigabytes of ram and if any machine would be created which depleted resources, the machine would not be able to start. Is this correct? If so, then how the RP can manage how much mhz CPU using each machine? If all 5 machines were launched at the same time, would not be the limit of 10 mhz be quickly exhausted? The machine would be stopped / stop? Or would the machine just run with > less < mhz?

  RPs affect DRS or HA? How can he? Because the DRS moves a machine so she uses a fixed amount of resources on a machine, ESX, how RPs come into play if they are universal to the cluster?

  Thank you very much

  psynophile,

  Relevant issues. RPs are used "Undernet world", Yes, but I've not seen too real implementations using it. But everything I've seen, they work very well for purposes of limitation and booking. Answer your questions:

  "any machine would be created which depleted resources, the machine would not be able to start": it depends. The limitation will be strong for the RAM (the sixth VM fuel not on), but for CPU the ESX will try to share the 10 GHz (I guess than the typo in the MHz) with all the virtual machines on the RP - always count you can provide each machine with a reserve of CPU, so if the reservation is greater than the limit , then you may not be able to power on the nth VM.

  If so, then how the RP can manage how much mhz CPU using each machine? If all 5 machines were launched at the same time, would not be the limit of 10 mhz be quickly exhausted? : it depends on the use of each virtual computer processor. The performance will be degraded IF the limit of 10 GHz is not sufficient to them.if you 5 database within this RP servers, they will probably present a performance degradation. But will never halt/stop.

  RPs affect DRS or HA? : as the RPs are on a group level, they do not. DRS will change virtual machines one ESX to another depending on the host CPU/RAM usage. HA won't be affected, only that your reservations can reduce the amount of servers for failover, you have set up for it.

  Several docs on this subject: http://www.vmware.com/pdf/vi3_35/esx_3/r35u2/vi3_35_25_u2_resource_mgmt.pdf

  Hope this helps,

  Marcelo Soares

  VMWare Certified Professional 310

  Technical Support Engineer

  Chief Executive Officer of the Linux server

• How to manage the padding issue &amp; bytes - ordering when you change the resource (PiPL) file in windows?

  Hi all

  I just started programming sdk photoshop. I noticed that the resources provided by Adobe Guide recommends to develop dialogs using Mac ground language and converting it into window using the CNVTPIPL resource file. EXE. If you use a windows resource editor, padding and byte-ordered issue must be handled by the programmer himself. Since I'm not sure what is the architectural differences between a PC and a Mac, can someone explain to me exactly how padding and byte-ording problems are handled under the windows resource editor? It would be good if there is no concrete example.

  Thanks for any help!

  You really shouldn't edit resources directly if you can avoid it.

  Simply modify the .rc files or Betty and recompile.

  Macintosh, used to use the big-endian byte order, but didn't for several years because they switched to Intel processors.

• Name resource RIO issue

  Hello

  I have a request to change the name of RIO resource (not the alias), I think that it is auto-generated and not something that I can put. If I'm wrong, someone could show me how and if I'm wrong can someone direct me to the documentation?

  Thanks in advance

  Emma

  Hello Emma,

  I'm Nick, an Applications Engineer at NEITHER.

  You are right, there is no way of choosing the name of RIO resource manually. It's the same principle as with port numbers.

  I don't see any of the documentation, it is implied, and also, that is why we have introduced aliases.

• Issue user account controls? message "resource loader cache not have loaded MUI entry" you try to run Norton System works on cd with UAC.

  I am running vista Home premium, upgraded from xp. I can't run norton system works setup cd with controls (UAC) user account enabled and on. I get the message "resource loader cache has no load MUI entry" I can run from cd with disabled UAC and offshore. What should I do to fix this?

  Hi David e. Sunderland

  Method 1
  When you are working on your computer and install a new program, the installation suddenly fails. Now, you're left with a partly installed program. You try to install the program again, but you're unsuccessful. Or, maybe you have problems trying to remove an old program because the installation files are damaged.

  Problems installing and uninstalling programs on Windows computers
  http://support.Microsoft.com/kb/2438651/

  Method 2
  You can try to install the program to boot.

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7
  http://support.Microsoft.com/kb/929135
  Note: follow step 7 of section of boot KB929135 to the computer in normal mode.

  Method 3
  Run the Norton System Works as an administrator and check if it helps

  How to enable an application to run once with a full administrator access token in the UAC?
  http://Windows.Microsoft.com/en-us/Windows-Vista/how-do-I-allow-an-application-to-run-once-with-a-full-administrator-access-token-in-UAC