ripple noise / and defective corrections acquires with SMU-4496 hammer

Similar Questions

• How to acquire with NiScope at different sampling frequencies and lengths Records?

  I need to acquire the data of 2 channels of the NI PXI-5114 map two different sampling frequencies high, at the same time. Also, I put 2 different record length. Is this possible?

  I understand that 'Vertical' settings can be configured for individual chains because the function 'Vertical niScope Configure' has 'channels of entry with which we can assign the desired channel. But for horizontal settings such as "min sampling rate" and the record min length, I could not find such an option to specify the channel. Would it not common to both channels?

  I hope that the device is capable of simultaneous sampling and therefore channels can be configured individually to different sampling rate.

  Hi AJ_CS,

  Why do you have to be distinct from sampling frequencies on channels separated from the digitizer even?  What different sampling rate do you want?

  But for horizontal settings such as "min sampling rate" and the record min length, I could not find such an option to specify the channel. Would it not common to both channels?

  You do not have an option to configure the settings of hoirizontal on a channel by channel basis because this concept does not exist in the traditional sense of the use of a scope.  Compatible with the concept of IVI, an oscilloscope traditional benchtop will have only a button or a set of buttons for setting the parameters of synchronization of the unit.  There is therefore no horizontal configuration to separate channels on the scanners NOR.

  I hope that the device is capable of simultaneous sampling and therefore channels can be configured individually to different sampling rate.

  Similar to a traditional benchtop oscilloscpe, the device is capable of simultaneous sampling.  But as mentioned above, the channels can not be configured for different sampling frequencies high.

  However, you can ignore data that you think is not relevant.  For example, if you assign 100MS/s CH0 and CH1 to 50 MS/s, then you throw all other samples.

  Alternatively, you can use separate scanners (a channel on each digitizer) and configure them to taste at different rates.  You can set frequencies of sampling on scanners NOR separated and even synchronize them with TClk.

  -Andrew

• APS Shaker and amplifier work with SMU-1071

  Recently, we bought a shaker APS 113 and 125 APS amplifier for our new research project. We want to use NI-SMU-1071 controller system to control the shaker via amplifier.

  NEITHER SMU-1071 > APS-125 amplifier > APS 113 Shaker

  APS asked us to use Spektra VCS 403 (Vibration Control System) for this case. When we tried to use this software, there is an error in "open loop". But all things related very well. Amplifier and shaker do not work.

  The seller company has no effective technical information. Please let me know your solutions, thank you.

  Again, the 1071 is just a chassis. There must be some specific cards in it and you have not yet identified these cards.

  In all cases, you will need to obtain assistance from the supplier of the custom software unless you intend to write about something else and need some help with that.

• ORA-00054: resource busy and acquire with NOWAIT specified or timeout expired

  Hi all

  I use oracle 11.2.0.3 with 3 node rac ODI.

  I have the table which I am not able to fall and give the error below.

  SQL > drop table I$ _CDS_FAULT_DEV1;

  fall of table I$ _CDS_FAULT_DEV1

  *

  ERROR on line 1:

  ORA-00054: resource busy and acquire with NOWAIT specified or timeout expired

  SQL > show parameter ddl_lock

  VALUE OF TYPE NAME

  ------------------------------------ ----------- ------------------------------

  DDL_LOCK_TIMEOUT integer 300

  I changed to 100 but still the same error too, I checked and there is no lock. Can you please provide me with a way to solve this problem.

  Kind regards

  DBApps

  For sure there are locks, because the table is in use.

  Drop table wants an exclusive lock on the dictionary or the corresponding records.

  When the table is used there will be a lock from line on the document in the dictionary.

  Have you consulted with SGS$ access?

  Please do so now.

  -------------

  Sybrand Bakker

  Senior Oracle DBA

• ORA-00054: resource busy and acquire with NOWAIT specified

  Im running 2 updates in the same pattern, but in 2 completely different tables via sql loader.
  
  Due to synchronization problems, they sometimes run at the same time. However I get the error message:
  
  ORA-00054: resource busy and acquire with NOWAIT specified
  
  When I get this error, he says its due to a lock on a table, but they are different tables.
  
  Any ideas?
  
  Thank you very much

  You can use commit / rollback to overcome this problem.

• Reference Dell MD3200i correct editing with IP system and the NIC for faster network speeds

  Hi all

  I worked on this project for a while now. I did a lot of research and have contacted Dell several times. I need help.

  I have 2 sets of identical to use for Hyper-V clusters servers. We bought a Dell MD3200i in November, we also bought a Dell 5424 switch and a Cisco SLM2048 switch. These servers have Real Tek 2 network cards for iSCSI Jumbo frames is 9 k

  The Dell MD3200i is two SAN controllers. Dell 5424 is the iSCSI optimized switch and Cisco is a 48 switch ports. iSCSI is on its own network that nothing else is connected to it. (There is an Iomega NAS and a promise Vtrak SAN Tech with all current domain of execution with iSCSI controller)

  Reference Dell MD3200i controller 0 Port 0 192.168.130.101 controller 1 Port 0 192.168.131.101

  Controller controller Port 1 0 192.168.130.102 1 1 192.168.131.102

  Controller controller Port 2 0 192.168.130.103 1 2 192.168.131.103

  Controller controller Port 3 0 192.168.130.103 1-3 192.168.131.104

  Cisco switch has 1 VLAN n ° 1 on it and the 130 subnet inside elements. There are 8 connections to the switch. 4 controller 0 and 1 of each of the servers. It has an IP of 192.168.132.4, but that switch IP does not make difference. Lighted Jumbo frames

  Dell switch has 2 of #1 for various things such as the domain controller, Vtrack, and SIN. Subnet 2 is 131 and has a total of 8 connectors inside. 4 in 1 controller and 1 from each of the servers. Lighted Jumbo frames. The switch IP address is 192.168.132.2

  Groups of servers. Each server node running Windows 2008 R2 SP1 and running hyper-v with virtual server clusters / storage folder on them. 2 Realtek NIC with Jumbo frames made 9 k ProdNode1 and ProdNode2 have 12 Core i7 CPU with 12 GB memory, EXNode1 and ExNode2 have 12 Core i7 CPU with 24 GB of memory.

  ProdNode1 iSCSI-1 192.168.130.110 ProdNode1 iSCSI-2 192.168.131.110

  ProdNode2 iSCSI-1 192.168.130.120 ProdNode2 iSCSI-2 192.168.131.120

  ExNode1 iSCSI-1 192.168.130.130 ExNode1 iSCSI-2 192.168.131.130

  ExNode2 iSCSI-1 192.168.130.140 ExNode2 iSCSI-2 192.168.131.140

  Portal discovery iSCSI on ProdNode1 went to 192.168.130.110 192.168.130.101 and 192.168.131.110 192.168.131.101 each of the other servers Discovery Portal have been pairs like this.

  iSCSI tab click on add 8 MPIO sessions at each of the ports on the MD3200i from Dell, target. For example, I added 1 session of 192.168.130.101 using it. Add Session,--> activate--> Advanced Mutlipath--> Local--> IP 192.168.130.110 initiator and target 192.168.131.101 iSCSI adapter. This is repeated on all servers. 4 connections for each NIC.

  The network is very slow. It revolved around 2 to 4 MB/MIN and it should be much faster. Initially, we had only the Cisco switch with only 1 VLAN and everything connected directly to it. I read somewhere that MPIO has been the problem, so I went through the same configuration but does not verify the MPIO checkbox above. Once this has been done, the network speed went up to 1.5 GB/Min but modular storage Dell was not happy, and virtual servers would fail and the connection is not very stable.

  What wrong with my setup? Can I directly home and fix the servers directly to the PowerVault and will make stable and allow for failover and redundancy NIC? I need to get this stable so I can move with something else.

  Thank you Ron

  You will need to change your system of intellectual property on this:

  rbramble

  EX-Node1 iSCSI-1 192.168.130.130

  EX-Node1 iSCSI-2 192.168.131.130

  EX-Node2 iSCSI-1 192.168.132.140

  EX-Node2 iSCSI-2 192.168.133.140

  Prod-Node1 iSCSI-1 192.168.130.10

  Prod-Node1 iSCSI-2 192.168.131.10

  Prod-Node2 iSCSI-1 192.168.132.20

  Prod-Node2 iSCSI-2 192.168.133.20

  Reference Dell MD3200i

  Controller 0 Port 0 - 192.168.130.101 Jumbo Frames 9K

  Controller 0 Port 1 - 192.168.131.101 Jumbo Frames 9K

  Controller 0 Port 2 - 192.168.132.101 Jumbo Frames 9K

  Controller 0 Port 3 - 192.168.133.101 Jumbo Frames 9K

  Controller 1 Port 0 - 192.168.130.102 Jumbo Frames 9K

  Controller Port 1 1 - 192.168.131.102 Jumbo Frames 9K

  Controller 1 Port 2 - 192.168.132.102 Jumbo Frames 9K

  Controller 1 Port 3 - 192.168.133.102 Jumbo Frames 9K

  Your iSCSI sessions will be:

  For EX-Node1:

  -192.168.130.130 to 192.168.130.101

  -192.168.130.130 to 192.168.130.102

  -192.168.131.130 to 192.168.131.101

  -192.168.131.130 to 192.168.131.102

  For EX-Node2:

  -192.168.132.140 to 192.168.132.101

  -192.168.132.140 to 192.168.132.102

  -192.168.133.140 to 192.168.133.101

  -192.168.133.140 to 192.168.133.102

  For Prod-Node1:

  -192.168.130.10 to 192.168.130.101

  -192.168.130.10 to 192.168.130.102

  -192.168.131.10 to 192.168.131.101

  -192.168.131.10 to 192.168.131.102

  For Prod-Node2:

  -192.168.132.20 to 192.168.132.101

  -192.168.132.20 to 192.168.132.102

  -192.168.133.20 to 192.168.133.101

  -192.168.133.20 to 192.168.133.102

• photosmart HP 5510 vote B11a: noise and Auful printing problem

  Hello world

  I'm new here.

  I have a problem with my photosmart HP 5510 printer, when I try to print it makes a terrible noise and it does not print.

  I try update firmware, reset the printer, change the cartridge, remove all the piece of paper, but nothing.

  Could you help me please?

  Thank you

  Alessandro

  Hi @alessandro96

  I'd love to help you with the sound that you hear from the printer. I understand that you have already begun to solve the problem, but the noise remains. Please post back with the answers to the following questions;

  1. Is the printer on a flat surface?
  2. How long has noisy for the printer?
  3. Didn't help then the noise started? (ie. the paper, printer error message jam was fallen/hit, surge)
  4. There are flashing lights, or the error messages on the printer?
  5. When was the last time that the cartridges have been changed?
  6. If you are a Virgin copy, when you hear the noise?
  7. If you open the printer do you see broken parts?
  8. When opening upward where the cartridges go, they move freely?
  9. The cartridges are installed correctly? (ie. the cartridges are level and does not appear).
  10. Perform a hard reset. With the power on remove power cord from the back of the device, then from the wall outlet. Press and hold the power button for 30 seconds (drains the excess power of the printer). Plug the power supply into the wall outlet, then the printer.
  11. You still get the noise after that?

  I look forward to hear from you.

• Portege M800 - noise and HWSetup does not start

  Hello

  I use a Portege M800-116 under XP - SP3.

  Problem 1:
  Connection Line-Out to a stereo system and play music with Winamp or WinMediaPlayer works fine on battery.
  As soon as I connect the power adapter, a whistle loud high frequency and UM static disrupts the experience.

  Problem 2:
  Files WAV or MP3 recording with internal or external microphone produce mediocre results.
  The resulting files include a high level of high frequency noise and hum static.
  Connect the power supply increases the problem.

  Comparing the quality of the recording and playback with my old confidence Portege M100:
  My M800 is one not only of poor quality - it's plain unusable.

  Problem 3:
  Toshiba HWSetup does not start from the control panel.
  Have you tried the ONU - and re - installing nothing helps.

  Thank you for guiding me towards a solution.

  Concerning
  T

  Hi, fly,

  I m not Portege M800 owner so I can t he test for you, but I think that if the problem occurs only when the AC adapter is connected, it s a grounding problem

  You have 3-pin or 2-pin AC/DC adapter?
  As far as I know in this case you need 3-pin AC/DC adapter and power cord.

  You should ask an ASP in your country. Guys can order a new AC/DC adapter and check your laptop to what the problem is exactly.

• Satellite L855 makes a noise and hangs expecially in games

  Hello.

  I just bought a SATELLITE L855 - 10 p (http://pt.computers.toshiba-europe.com/innovation/jsp/supportMyProduct.do?service=PT), with last Wednesday ATI graphics card, but my computer came with one problem (which I will try to explain, because already, I went to the store to pass for another and the cams newone with the same problem as the previous one, also the tecnic can't find the error). Now the problem:

  When I'm in 'youtube' or 'windows media player' or expecially when I play LoL (League of Legends, online game) my computer freezes for a few seconds (one or two) and that it crashes, it makes a noise too.

  If I'm with a helmet I listen to that noise in the headphones. I tried everything like reinstalling the video card and sound card drivers and it changed nothing, accidents and noise remain. I don't know what to do...-

  Is there a solution? I can not even find what the problem... And tecnic store seems to not be able to solve either...

  I appreciate your help.

  Post edited by: Eric

  Hello

  Could it be that the system hangs during the second view and appears so this strange noise?
  In most cases, the system hangs because the CPU is stressed and overloaded

  Someone in this thread had some streaming video LAG
  Maybe your problem could be solved also.
  Check:
  http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?threadID=67087

  Another idea:
  http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?threadID=67467

• Re: NB200 - making noise and the screen turns white

  Hello

  My laptop makes the high pitched noise and the screen turns white. Please help with this question.

  Thank you

  Hello

  It is especially as this problem with the inverter. She is, die, and made a noise of pitch. Try to connect the external monitor and check if it is displayed.

  Welcome them

• generation of sinusoidal wave with smu

  Is it possible to generate, for example, one 3 a 50 Hz sine wave with SMU 4138 or 4139?

  THX

  The DCPower API provides no screws to use blocks of power or SME like FGENs.  However, it is possible to program the jury at the exit of the standard functions by translating the desired frequency and amplitude to a sequence of continuous output with delays of source is defined so that the output function the user selects is output on the terminals of the device.

  The attached program allows you to use a NI 414 x, NI 4135/4136/4137/4138/4139 as a FGEN.  As it is, the program is limited to a maximum output frequency of 5 kHz.

  I have attached a version of the code for the current output and a version for output voltage waveforms.

• Noise measurement of an accelerometer with card PCI-4461

  Hello world

  I'm trying to measure the noise of an accelerometer, except with a card PCI-4461.

  First of all, I measured manually this noise with the help of a HP35665 signal Analyzer. I get something like this:

  

  And now with LabView and the PCI-4461 map, I get this:

  

  My question is: Whence this part? And how to remove it? (Since there is no with the signal Analyzer)

  

  I'm using LabView 8.5.

  This is how I configured the DAQ acquisition:

  

  and it's my VI:

  

  Thank you in advance for help

  Arthur

  
  

• Cannot acquire with cDAQ in hardware mode timed using DIAdem DAC

  Hi all

  I use DIAdem DAC to acquire the cDAQ + 9225 + 9219. 9219 acquires the use of single point mode that works very well. However, I tried to acquire waveforms 50 kHz 9225 with the file attached dac. However, I found a problem on the block of the clock, as shown below.

  

  How could I solve this problem and gain the waveform with 9225 using DIAdem DAC?

  Sincerely, Kate

  Hello Kate,

  You must connect the NIDAQ-In1 exit the Save block block. In addition, you must change the parameters of the horloge1 block. The material is always measured in mode "DAC-kernel". "The software clock" is used for frequencies of up to 10 kHz clock (depending on the material and the PC). If you want to measure more quickly, you can use the "Clock" mode

  Greetings

  Walter

• Loud grinding noise and vibration: HP Pavilion G6-2313AX

  I own a HP Pavilion G6-2313AX, I bought 4 months ago. The laptop worked very well and I am very happy with it. Hower a problem has arised recently.

  My laptop fan makes a humming noise and creates a lot of vibration. It is, as I believe, not a normal behavior. I checked online for solutions and the potential causes. Most of them seem to think that what I need is to get the fan cleeaned.

  Now, my question is: should I expect as a result to a computer store, or should I go to a center of HP? It will make me pay so much? I live in India.

  Also, is it possible that this is another thing that a fan dirty which is the cause?

  just don't push it, no need to open it.

  

• How can I measure the continuous component of the tension a SMU-4496 with LabView

  Hello

  I use an SMU-1073 NI with an SMU-4496 for several applications. In one of them, I would need the blood, maintain the continuous component (this is an accelemeter of MEMS). It's standing vertical, it gives, for example, + 2V and I need to keep reading this almost constant value.

  However, with the DAQ Assistant in LabView, it seems that it only reads the component changing signal, as is it doesn´t to move, it reads almost 0. If it moves, the, the DAQ system takes the change but then returns to zero.

  Is this normal? Read the constant part of the signal?

  (I'm a mechanical engineer and I'm not at all an expert in acquisition of signals or data, so probably just something basic is missing me)

  I have attached an example in which, after a change, it goes back to zero and the configuration in the DAQ assistant

  Thank you

  AC coupling is the culprit-it allows to block all components of steady state DC.

  -AK2DM