photosmart HP 5510 vote B11a: noise and Auful printing problem

Similar Questions

• HP B210a Photosmart and iPad2 printing problem

  Hello.
  I just bought the B210a for my iPad2 wireless printing. I joined the printer properly to my W - LAN network (as far I can tell there is no problems with the WPA or IP) and implemented by following the instructions in the manuals. I had no problem printing from my PC. My iPad also recognizes the printer without problem. But when I try to print from my iPad (on Safari and hp iPrint) the printer does nothing. HP iPrint starts the race printingprocess for a few seconds and then tells me something from (excuse me, I have to translate it from German) as "possible within printing problems. Check the printer for more information". My printer does not show anything.
  -The report says it all test is successful, the quality of the signal is fine, the identifier SSID is correct, MAC, IP address, DHCP, infrastructure, WPA - PSK and automatic encryption (AES)
  -in my router configuration screen, the printer has been Born as a networkdevice with IP address
  -MAC filtering is turned off
  -W - LAN mode is 802. 11 b/g to channel 13
  -WPS is disabled because it caused problems connecting the iPad to W - LAN
  -My iPad is also in the W - LAN, network and can access the internet through a router
  -I can't acess the printserver B210a via the IP address of my PC's built-in
  -all devices are in the same subnet 192.168.1.xxx
  -J' have already disabled the power of my iPad, printer and router and got no result

  I hope you can help me. Thank you.

  I just found the solution: I just had to restart the IPad2 (hold both keys). Now, it works fine.

• Photosmart premium c309g-m rattling noises and then says "paper jam".

  Print a report and when I try to print another report the sounds of "grinding" printer and says now "paper jam".

  When the print order is given now just clicks and keeps saying paper jam.  There is no paper jam I can find.  I cleaned the paper rolls, but that did not help.

  A printer in a "geek" and it was not repairable.  Buy a new.

• Photosmart Premium C309-g: the drivers and the printer software will not be installed.

  My network all-in-one Photosmart Premium C309-g worked very well on my desk until recently, when suddenly the HP software could still see and connect to the printer, but Windows 10 could not. I tried to remove the printer and uninstall all associated software, then tried to reinstall the software. Unfortunately, the installation will not get to the point where it starts and then suddenly disappears with no trace of her still running in the background. I can deviate from the default installation and bring to the top of the page to select the components that I want to install, but when I do the button 'ok' on this page does not work. No matter how many times I click on it, the page remains open and the installation will not so fast. If I click Cancel on this page, it disappears and the installation back to the previous page, where I can choose to continue and happen almost immediately out of sight again. This happens whenever I try to install selected software and drivers. I deleted the printer from the devices page in the Panel, I made sure to this it is not is more listed in the Manager of peripheral devices (printers and imaging devices), I removed the Windows 10 print queue and I deleted all the data of the folder under the Program Files (x 86) HP folder on my hard drive. I also disabled Windows Defender and run the installer as administrator, yet none of these steps help the process at all. I have never, in my 20 + years using nothing other than printers HP, encountered a problem like this. I'm used to receive error messages during the installation of software to fail, but I have never had a process simply disappear from the computer without leaving any trace of never having run. I hope that someone out there has an idea, that I have not thought yet, transferring files to my tablet to print from becomes a pain in the rear.

  A man who took the freedom of another man is a prisoner of hatred, he is locked behind bars of prejudices and narrow-mindedness. I am not truly free if I take freedom away from someone else, as surely as I am not free when my freedom is taken from me. The oppressed and the oppressor similar are stripped of their humanity.
  ~ Nelson Mandela

  Welcome to the HP Forums @GarfieldFan1969,

  I understand the printing software will not fully installed for your Photosmart C309 on your system Windows 10, and I wanted to answer with my suggestions for trying to help! Here are my suggestions for you to try. When you are finished, please let me know the results and problems or errors that you may encounter!

  First step: clean boot, restart the PC and try the install again.

  1. start by typing "msconfig" in the search box of Cortana, and then click MSConfig (run command)
  On your keyboard press Windows + R key at same time and type Msconfig in the run window, and then click OK or press ENTER.

  2. now, choose Selective startup

  3. Remove the check of the Load Startup items

  4. click on the Services tab

  5. check "hide all Microsoft Services" and then click on disable all

  6. click apply , then OK

  7 restart the PC and temporarily disable firewalls or antivirus programs

  8 run the Installation Wizard for Windows HP printer to install the printer

  9 turn on the firewall and start services

  Second step: you unregister and re-register the Windows Installer Service:

  1. hold down the Windows key + R to fill the box "Run" and type cmd.exe, and then click OK.
  2. at the command prompt, type msiexec /Unregister , and then press ENTER.
  3. at the command prompt, type msiexec/regserver, and then press ENTER.
  4. at the command prompt, type exit and press ENTER to close the command prompt.
  5. run the Wizard for Windows HP printer installation

  Step 3: run System File Checker Scan (up to 3 times) to repair the corrupted system files:
  1. go to start
  2. type CMD
  3 right-click and run as administrator
  4. to check and repair the OS type sfc/scannow (note the space between sfc and ' / ')

  You may need to run this upward to 3 times to solve all the problems

  When finished, it will say one of three things
  Windows did not find any breach of integrity (a good thing)
  Windows resource protection found corrupt files and repair the (good)
  Windows resource protection found corrupt files but was unable to fix some (or all) of them (not a good thing)

  Try to reinstall the printer.

  Step 4: activate the built-in Windows administrator account

  source

  1. first of all, you'll need to open an administrator mode command prompt by right-clicking and choosing "run as Administrator" (or use the shortcut Ctrl + Shift + Enter in the search box).

  Note that it works the same in all versions of Windows. It just search for cmd and then do a right-click on the icon of the command prompt in the start menu or the boot screen.

  

  2. If you are in Windows 8.x or 10 you can click on the Start button and choose to open a command prompt in this way.

  

  3. now type the following command:

  NET user administrator / Active: Yes

  

  4. you should see a message that the command completed successfully. Log out, and you will now see the administrator as a choice account.

  (Note that this screenshot is for Vista, but it works on Windows 7 and Windows 8 and Windows 10)

  

  You will notice that there is no password for this account, so if you want to leave it enabled, you must change the password.

  Try to reinstall the printer.

  

  Testify of my answer by hitting the thumbs to the top slot

  Click on the button "Accept as Solution" if I helped you reach a solution.

• After paper jam, rolls making noises and the printer takes a long time to spit the copy.

  It is an all in one Officejet Pro 8600 and is still under warranty. How can I get fixed roller?

  Wow!  I found the video on how to find a paper jam!    It was a step that was not included on the instructions of the machines, i.e. check behind the print cartridge and the whereabouts of my paper jam!   When everything has failed, read the instructions, eh?

  Thank you!  My problem is solved!

• * USB ports and my printer problems

  My laptop is Windows Xp edition sp2 family.

  My old HP laptop computer of 4 years has 4 USB ports. Unfortunately, 3 of the 4 ports broke physically, so I only have a single functional port.

  A port that works cost of my cell. So I know it works. But now, only 40% of the time it will print when I plug my 750 HP printer all in one in it.

  Otherwise, it will display a "?" on the printer in the taskbar icon. Once, I unplugged the USB cable and plugged into the broken USB port holding it still and it actually print my papers.  But as I said I have been lucky that day cause these 3 ports are broken.

  What can I do to make the only port 1 have, can work for all devices I. It seems not only act with the printer.

  In addition, supplants ports broken something painful, costly or difficult to do? I know it can vary depending on the brand of the phone... But overall, it might be an easy solution?

  Thank you all in advance...

  Hello
   
  Method 1.
  Let us run the fixIt in the article below and check.
  http://support.Microsoft.com/kb/925196/en-us

  Method 2.
  Let us, remove and reinstall the usb controllers and check.
  To remove and reinstall all USB controllers, follow these steps:
  a. Click Start, click Run, type sysdm.cpl in the Open box and then click OK.
  b. click on the Hardware tab.
  c. click the Device Manager button.
  d. expand Bus USB controllers.
  e. right click on each device under the Bus USB controllers node and then click on uninstall to remove them one at a time.
  f. restart the computer and reinstall the USB controllers.
  g. plug in the removable USB storage device and perform a test to ensure that the problem is solved.
   
  Reference:
  Advanced troubleshooting tips for General USB problems in Windows XP
  http://support.Microsoft.com/kb/310575
  You can also download and install the dricers from the link below.
  http://h20000.www2.HP.com/bizsupport/TechSupport/ProductList.jsp?lang=en&cc=us&TaskID=135&prodSeriesId=295845&prodTypeId=18972

  It is an alternative to repair broken ports, you can purchase a usb hub, you can insert it in the usb port that works, and then use the available ports on the hub. Find out the nearest computer to usb hub store.

  I hope this helps.

  Thank you, and in what concerns:
  Shekhar S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.
  If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• only of black and white prints

  My sisters new want 5660 printer prints only in black and white.

  I have been all over the net and my iMac to try to understand what is the problem, but nothing helped.

  I looked for the paper type / quality etc settings that were solutions to other problems, but these options are not on my computer.  I passed through all the menus on the printer and many of my programs in an attempt to change a few settings that is saying is not in color, this printer.  I opened the printer settings and the settings of my computer and nothing gave me the possibility to print in color or black and white.

  what the devil?

  the closest solution to you, that I could find was that someone uninstalled and reinstalled the printer and it helped for a while, until she had to repeat the same thing.  that cannot be a workable solution, and my first guess would be that there is a problem with the printer.

  However, if there is something that I am on, can you please let me know?  I'm annoyed at the moment and it's not yet my printer...

  Hello @jammypie,

  The reason why the HP ENVY 5660 e-all-in-one printer is not printing correctly from your Mac OS X 10.6.8 computer is because the printer is not compatible with Mac OS X 10.6.8.

  Because this printer is new, it is only compatible with Mac OS X 10.7, Mac OS X 10.8, Mac OS X 10.9 and 10.10 to Mac OS X. Therefore, there is no driver support on your Mac OS X 10.6.8 computer. I'm surprised that you were able to get the printer to print to your Mac in the first place. But this does not explain why your print quality is so bad. You can try the alternate drivers that appear under the screen (+) add under Print & Fax but I can't guide you to a driver who would be appropriate for your printer, because it is not supported on this operating system. It is an inkjet printer if you can try a few other ink jet pilots who appear in the list.

  The solution to this problem would be to install the desire on a supported operating system and all printing problems will be resolved.

  I wish you good luck going forward with this!

• Photosmart HP 5510 invites to indicate the user name and password

  Hi people,

  I put a static IP address for the Photosmart HP 5510. When I navigate to , I get a pop-up dialog box requesting a user name and password.
  
  Does anyone know how to reset it on the Photosmart HP 5510?

  Thank you very much

  concerning

  Hey Joe,

  Try the following steps below.

  1. press the button on the control panel wireless

  2. tap on settings

  3. scroll down to the network by default, then press Ok

  You should be able to access the security settings in the built-in Web server now. Let me know what you find?

• Photosmart HP 5510 B111a-printing of Ipads, host names and more!

  Hello

  I have 5 of these photosmart printers installation in various places around our school to allow printing of the iPad 2 that have been deployed to classrooms.

  The problem is it seems to be a way to identify the different printers on the network when printing of you ipads. When I click on print and then select a printer list shows "PHOTOSMART HP 5510 B111a [C95...

  The [C95 corresponds to the first three digits of the host name of the printer, the problem is that three out of five printers have the same first three digits and are all the same displayed as the example above and therefore gives no idea of what printer you select until you print.] Which is not very practical in a school of our size!

  I connected to the HP configuration page using the IP address and changed the host name, but it changed only on windows-based hardware.

  So my question is: is it possible to change the name of the printer to allow me to determine what printer I print from an iPad? If this isn't the case, any other solution would be great.

  Hello

  You can change the identification of the unit of the printer, following embedded Web server:

  1. Access SAP from your browser by using the IP address of the printer.
  2. Enter the network tab.
  3. Enter the network.
  4. Enter Hello.
  5. Change the Name of Service Hello , as required, the updated name will appear on any Apple device.
  6. Click apply to save the changes.

  Kind regards

  Shlomi

• My Photosmart HP 5510 repeatedly do not print and says it is offline

  I tried a hard reset several times: IE in pulling cord exit printer & on the wall. Wait 60 seconds & then reinstall. It worked before but not this time. The PC can not simply see the printer to print even if the printer appears clearly in devices & my printer as the default printer. Please help - I have a big project to do & I don't want to have to buy a new one.

  Hello
  
  Thank you for using the HP Forums. You can try the following:
  
  Please download and run the HP Print and Scan Doctor (PSDR) tool to diagnose and solve your problem
  
  http://h20180.www2.HP.com/apps/NAV?h_pagetype=s-926&h_lang=en&h_client=s-h-E016-1&h_keyword=DG-PDU

  If this does not work, you can uninstall and reinstall the software features FULL?
  
  Hope that helps.

• I use Windows 7 and my pc does not recognize my wireless Photosmart HP 5510 printer

  It will print but after not using it for awhile, when I try to print, I get the message that my computer can not find printed

  First thing I would try is restart your wireless router and if this does not work, it give a try.

  HP Print doctor for help with many printing problems

  http://h10025.www1.HP.com/ewfrf/wc/document?cc=us&LC=en&docName=c02073861&JumpID=ex_r4155/HHO/IPG/ccdoc/trailhead_doc&lang=en

  I hope this helps.

• Photosmart HP 5510: printer not connected to the network, although it

  Hi people,

  I am at my wits end with this and you are my only hope (what Star Wars quote).

  I have a HP Photosmart 5510, I've had around 2011.  I've always used it in the company of my iMac (OS X now on El Capitan). Over the last year or two, there was the strange number to which case when I open the HP utility on my iMac it says it is not able to connect to the printer and I should check that it is switched on (this is before you ask). This question seemed to resolve itself after a short while and there was no problem.

  However, I came to analyze some elements of the other day, and this same old issue again raised his head. I put my paper on the scanner and press the option scan only for the printer to tell me that there is no connected computer. Weird, I thought I had printed only some points the day before. I went to my iMac and open the HP utility to see my former favorite message that the printer was not plugged in blah blah.

  I went on HP website to see if there were new pilots required, which it was not (the last was for OSX Yosemitie!).

  I decided to try and start fees and remove the printer and re - add new. I deleted the printer, downloaded the latest HP deriver (just in case) and that's where everything went wrong.

  Software downloads, all right, it starts going through the installation process, end, then he gets to the selection of the device, issue. It evokes three devices that are my one and only printer (Strange I thought). Two with the "connection type" listed as Hello and the other with the connection type is listed as IP. I tried selecting each of these only for each of them to come back with the following error message:

  "YEAR error occurred while the communications device." Please make sure that the device is ready and try again." Well, if they hear by loan, circuit implementation, its connected to my network then YES ITS BLOODY LOAN! So I get no more on the process by the printer and HP Utility installation is nothing else than a large black plastic paper weight. I tried to reconnect my printer to my network wifi several times and everything is fine, its connected and there is no problems according to the page of "wireless network test results" print.

  What the hell is happening? Any ideas? Please save me before I throw this thing by the highest window that I can find.

  I'm not a computer expert and I'm certainly not a network specialist. All the advice is appreciated greatly and fortunately.

  Hey @Mvdarbs,

  Welcome to the Forum from HP Support. We're here for another help to get the most out of our products.

  Thank you for your message. I see that you experience the Mac-to-printer communication problems when you use the HP Photosmart e-All-in-one 5510 printer. All this happens despite your apparent WiFi connection. While it is no doubt frustrating to live when all you want to do is print, there are solutions that you can try and I hope that they will restore the regular feature.

  I recommend you try the following steps:

  (1) we will start over with the installation of your network printer. From the control panel press the wireless icon, and then select "Restore network Defaults."

  2) façade, run the "Wireless Setup Assistant." Reconnect to your home network and then make a note of the IP address.

  3) visit the printer embedded web server (EWS): this is done by entering the IP address of the printer in the address bar of the web browser and navigating to this address. If you have a security alert (as this page is not encrypted), click on to "Go forward anyway." If the page loads correctly, we can be certain that the network connection is real. While you're there, make a note of any error messages or status alerts (if you see it, it's all good) and don't forget to advise me on what you see.

  4) remove the printer from your Mac. If you are not sure how, refer to the

  guide for advice.

  one) (optional)-set a static IP address for your printer. Refer to this thread of @PrintDoc here: http://h30434.www3.hp.com/t5/Printers-Archive-Read-Only/changing-IP-address-for-wireless-printer/td-p/445087 for instructions on how to do it.

  5) reinstall your printer: click here and install the driver that you are prompted.

  Please let me know the result of your troubleshooting by responding to this post. Don't forget to come back to this thread and check "Accept as Solution", if I have successfully helped solve you the problem. If you want to say 'Thank you' to my effort to help, click on the "thumbs up" to give me a Kudos.

  See you soon,.

• Problems scanning on Ubuntu with Photosmart HP 5510

  Hello

  I can print (wireless) of my HP Photosmart 5510, but cannot scan. I've got version 3.14.3 HPLIP (recent, but not the most recent). I tried to install the latest version of HPLIP but cannot work out how to do (I'm quite new to Ubuntu). Can anyone help?

  Thank you
  Laurie

  HI Laurie,

  Please download the latest HPLIP for Photosmart 5510 from here:

  http://hplipopensource.com/hplip-Web/models/Photosmart/photosmart_5510_series.html

  The analysis is expected to be launched from the PC. and a printer (as shown in http://hplipopensource.com/hplip-web/models/photosmart/photosmart_5510_series.html#note3 )

  Scan of the PC can be launched via an compatible with SANE like GIMP application. In other words, you can download a http://www.sane-project.org/sane-frontends.html for a GUI application to allow you to scan to PC.

  Press Bravo if it helps.

• My Photosmart HP 5510 Scan photos in the file on my Mac running Yosemite

  I get an error message that the parsing failed everytime I try to scan a photo.  I downloaded the latest driver through the Apple App Store.  I rebooted the computer and the printer.  Help!

  Hi @JaneCat,

  Welcome to the HP Forums!

  I understand that you cannot scan pictures of your HP Photosmart 5510 to a file on your Mac of Yosemite. I'm sorry to hear that, but I'm happy to help you!

  I recommend to download the drivers and full software functionality of our Web site, HP Photosmart 5510 e - All - in - One printer full feature software and drivers, as it is compatible with Mac OS X Yosemite.

  If you still have questions, I also recommend this analysis guide, a Message appears "No computer found" during scanning. Then follow the steps in the section that says it's for, Mac OS X 10.6 Snow Leopard, OS X v10.7 Lion, v10.8 Mountain Lion OS X or OS X v10.9 Mavericks. Given that these steps will still work on Mac OS X Yosemite.

  I also see this how to scan guide, scanning with HP software full feature in OS X v10.10 Yosemite.

  Hope this information is useful and thanks for posting!

• Photosmart 5510 requires the color cartridge to print in black

  I have an Imac running MAC OS X 10.7.5 and a HP Photosmart 5510.

  I can't select a black and white printing other than "regular, fast rough, black and white paper.

  QUESTION: Why are there no "plain paper, best option, black and white"? Or should I ask, where is the ordinary paper, the best black and whitee option?

  Surely each printer must be able to print the last option.

  To satisfy my need for a good level of black and white print that I have to use the color cartridges - it is expensive.

  I would be grateful for any help.

  Thank you.

  To print graphics or the text of quality 'Best' the printer uses color ink.  In the case of text, the color ink is printed black to improve the darkness and roughness of the edge.  (Color ink makes printing 'together' more quickly, reducing the purge on the edges).

  For graphics, the printer uses drops color printing black or gray printing mode best because it gives much better graphics.  The color ink droplets are much smaller than the black.  When the color ink is used for printing in grayscale or B & W graphics, the results are much thinner that the result would be in black ink only.

  If the quality does not matter (much) draft mode provides the best economy, but for a better print quality, color ink is necessary.