Route of replication traffic?

Similar Questions

• How to use the VMKernel vSphere replication traffic

  I'm trying to set up my host with my camera of replication with a stand-alone VMKernal with activated on its own virtual replication traffic vSphere VLAN.

  After that I have it set to 2 guests (each with local data warehouses) and tried to replicate a virtual machine from one host to the host with the VR device, traffic goes out on the management vlan / network card on the host of the virtual machine is received on the host with the device (where I'm storing data) on the VM nic inbound / vlan.

  I want 100% of my replication traffic off the coast of the management and the network of the VM, just as I did with vmotion.

  Hello

  On the establishment of the vmkernel to tag in ESXi 5.0.x and 5.1.x replication traffic is an experimental feature and still not officially supported.

  You have to somehow router ports of replication traffic. Some people use solutions WAN optimizer (Riverbed or similar).

  The VR device must be have access to vCenter Server and the hosts that can be used to write to data warehouses target. Link to article with the correct port numbers should be present in the Administrator's guide.

  Kind regards

  Martin

• vSphere replication traffic

  vSphere replication traffic is sent which vmkernel port?

  vSphere replication traffic is sent to the direction of vmkernel NIC for more information, see:

  http://blogs.VMware.com/vSphere/2011/10/How-does-vSphere-replication-work.html

• Routing of SSL traffic on two firewalls

  Hello

  I have HT an ASA face internet and destined for SSL connections. Behind the ASA I IOS Firewall that hosts servers must be accessed through the SSL provided by the asa

  The issue im having is: Users SSL Vett ends at the ASA fine, after that when I pass this traffic and in the firewall IOS, traffic does not reach the destination servers.   Newspapers in ios FW watch suite msg "Crypto packages re - CVD is not crypto IPSEC package"

  Please help me how to get these traffic routed via the ssl Protocol on the asa in the ios firewall

  I suppose it's possible you an IPSec VPN configured on the IOS Firewall including encryption field includes the one used by the SSL VPN client.

  The IOS Firewall has any IPSec VPN configured?

• ACLs on Cisco router - block outside traffic, allow all inside

  Hello

  I am creating the ACL on the router Cisco that will allow all traffic within internet and don't allow specific traffic on the internet inside.

  This is what I have configured and puted on the interface of the router connected to the ISP:

  10 permits all icmp (411 matches)
  20 permit tcp "my public IP address" no matter what eq 3389 (46400 matches)
  30 permit tcp "my public IP address" no matter what eq 22 (9185 matches)
  40 "my public IP address" ip allow match any (3207)
  50 permit tcp any any eq smtp (11 matches)
  60 permit tcp any any eq www (56 matches)
  70 permit tcp any any eq 443 (29 items)
  80 permit tcp any any eq field (5 matches)
  allowed 81 UDP everything no matter what field of eq (7 matches)
  allowed 82 UDP any eq (10564 matches) field
  83 permit tcp any what eq field everything (10 matches)
  90 permit udp any any eq ntp (13317 matches)
  95 permit tcp 192.168.0.0 0.0.0.255 any

  Dialer interface 1

  IP Access-group 101 IN

  So I can connect to my public IP to the LAN of the customer via RDP and SSH (which is OK), but users of the client cannot access Internet (which is not OK.)!

  Users are all in the same Vlan. Between the interface Vlan and outside interface (dialer 1) Pat.

  There is no other ALC on the router except for PAT.

  What I'm missing here?

  Thank you.

  Is this why 192.168.0.0/24 is present in the list of ACL 101? What is the remote subnet that you connect to port 3389?

  If your local subnet interior is a soldier of the C class, it must be your global external address you want to add to the ACL 101.

  Better yet, run an IPSec tunnel between the sites.

• Try to route all ipsec traffic

  Hello

  Can anyone help me please with config below. I am trying to route all traffic (web browsing) by the router.

  For now I can connect to the vpn and browse the network, but users cannot resolve web pages (page loading without end). If I activate split tunnel web browsing works but not what I'm used to.

  LAN pool 192.168.10.0/24

  local pool 192.168.20.0/24

  I assume it has something with ACL and NAT, but I can't understand that.

  Config is attached.

  Thank you.

  I think your config should work.

  The router which model is it and what version of software you are running?

• DMZ-Link bandwidth does not change the routing table countin traffic

  Hey guys

  I'm INE laboratories dong and shoved a weird one that delivers.

  I have configured the dmz-link bandwidtha nd the extended communities to send, I get the bandwidth in the BGP routes, however the routing table does not change the proportion of traffic according to the bandwidth available link.

  Here is my configuration:

  Rack1R6 (config) #do sh run | dry BGP

  router bgp 100

  no synchronization

  The log-neighbor BGP-changes

  BGP dmzlink-bw

  155.1.146.0 netmask 255.255.255.0

  aggregate-address 155.1.0.0 255.255.0.0 summary only

  neighbour 54.1.1.254 distance-54

  neighbor 54.1.1.254 dmzlink-bw

  neighbour 155.1.67.7 distance-300

  neighbour 155.1.146.1 distance-100

  155.1.146.1 neighbor send-community times

  No Auto-resume

  Rack1R6 (config) #.

  Rack1R6 (config) #do sh ip bgp neigh 155.1.146.1 opponents

  Version of BGP table is 35, local router ID is 150.1.6.6

  Status codes: deleted, cushioning d s, history of h, * valid, > best, i - internal.

  r SIDE-failure, stale S

  Source codes: i - IGP, e - EGP,? -incomplete

  Network Next Hop path metrics LocPrf weight

  * > 28.119.16.0/24 54.1.1.254 0 54 I

  * > 28.119.17.0/24 54.1.1.254 0 54 I

  * > 112.0.0.0 54.1.1.254 0 0 54 50 60 I

  * > 113.0.0.0 54.1.1.254 0 0 54 50 60 I

  * > 114.0.0.0 54.1.1.254 0 0 54 I

  * > 115.0.0.0 54.1.1.254 0 0 54 I

  * > 116.0.0.0 54.1.1.254 0 0 54 I

  * > 117.0.0.0 54.1.1.254 0 0 54 I

  * > 118.0.0.0 54.1.1.254 0 0 54 I

  * > 119.0.0.0 54.1.1.254 0 0 54 I

  r > 155.1.0.0 0.0.0.0 32768 I

  Rack1R6 (config) #do sh ip bgp

  Version of BGP table is 35, local router ID is 150.1.6.6

  Status codes: deleted, cushioning d s, history of h, * valid, > best, i - internal.

  r SIDE-failure, stale S

  Source codes: i - IGP, e - EGP,? -incomplete

  Network Next Hop path metrics LocPrf weight

  * i28.119.16.0/24 204.12.1.254 0 100 0 54 I

  *>                  54.1.1.254                             0 54 i

  * i28.119.17.0/24 204.12.1.254 0 100 0 54 I

  *>                  54.1.1.254                             0 54 i

  * i112.0.0.0 204.12.1.254 0 100 0 54 50 60 I

  * > 0 0 54 50 60 54.1.1.254 I

  * i113.0.0.0 204.12.1.254 0 100 0 54 50 60 I

  * > 0 0 54 50 60 54.1.1.254 I

  * i114.0.0.0 204.12.1.254 0 100 0 54 I

  *>                  54.1.1.254               0             0 54 i

  * i115.0.0.0 204.12.1.254 0 100 0 54 I

  *>                  54.1.1.254               0             0 54 i

  * i116.0.0.0 204.12.1.254 0 100 0 54 I

  *>                  54.1.1.254               0             0 54 i

  * i117.0.0.0 204.12.1.254 0 100 0 54 I

  *>                  54.1.1.254               0             0 54 i

  * i118.0.0.0 204.12.1.254 0 100 0 54 I

  Network Next Hop path metrics LocPrf weight

  *>                  54.1.1.254               0             0 54 i

  * i119.0.0.0 204.12.1.254 0 100 0 54 I

  *>                  54.1.1.254               0             0 54 i

  r i155.1.0.0 155.1.146.4 0 100 0 I

  r>                  0.0.0.0                            32768 i

  s > 155.1.146.0/24 0.0.0.0 32768 0 I

  * > i205.90.31.0 155.1.13.3 0 100 0 200 254?

  * 155.1.67.7 0 300 200 254?

  * > i220.20.3.0 155.1.13.3 0 100 0 200 254?

  * 155.1.67.7 0 300 200 254?

  * > i222.22.2.0 155.1.13.3 0 100 0 200 254?

  * 155.1.67.7 0 300 200 254?

  Rack1R6 (config) #.

  # now R4 configuration

  Rack1R4 (config) #do sh run | dry BGP

  router bgp 100

  no synchronization

  The log-neighbor BGP-changes

  BGP dmzlink-bw

  155.1.146.0 netmask 255.255.255.0

  aggregate-address 155.1.0.0 255.255.0.0 summary only

  neighbour 155.1.45.5 distance-200

  155.1.45.5 route-neighbour card GAME-54 on

  neighbour 155.1.146.1 distance-100

  155.1.146.1 neighbor send-community times

  neighbour 204.12.1.254 distance-54

  neighbor 204.12.1.254 dmzlink-bw

  No Auto-resume

  Rack1R4 (config) #.

  Rack1R4 (config) #do sh ip bgp Synt.

  Local router BGP 150.1.4.4 identifier UNDER number 100

  BGP table version is 18, table 18 main routing version

  15 entries for network using 1980 bytes of memory

  18 entries for path using 936 bytes of memory

  9/7 BGP path/bestpath attribute entered using 1512 bytes of memory

  3 entries for BGP AS-path ACCESS using 72 bytes of memory

  1 entries PMO community, using 24 bytes of memory

  0 cache entries of BGP route-map with 0 bytes of memory

  0 cache entries of filter-list BGP using 0 bytes of memory

  Bit entries in the cache field: 3 courses (up to 5) with 96 bytes of memory

  BGP using 4620 total number of bytes of memory

  Activity 102/87 BGP prefixes, 243/225, scan interval to 60 seconds

  Neighbor MsgRcvd MsgSent V AS TblVer InQ OutQ Up/Down State/PfxRcd

  155.1.45.5 4 200 8615 8640 18 0 0 07:38:02 3

  155.1.146.1 4 100 8761 8668 18 0 0 00:14:34 3

  204.12.1.254 4 54 8724 8595 18 0 0 07:38:02 10

  Rack1R4 (config) #do sh ip bgp

  BGP table version is 18, local router ID is 150.1.4.4

  Status codes: deleted, cushioning d s, history of h, * valid, > best, i - internal.

  r SIDE-failure, stale S

  Source codes: i - IGP, e - EGP,? -incomplete

  Network Next Hop path metrics LocPrf weight

  * > 28.119.16.0/24 204.12.1.254 0 0 54 I

  * > 28.119.17.0/24 204.12.1.254 0 0 54 I

  * > 112.0.0.0 204.12.1.254 0 54 50 60 I

  * > 113.0.0.0 204.12.1.254 0 54 50 60 I

  * > 114.0.0.0 204.12.1.254 0 54 I

  * > 115.0.0.0 204.12.1.254 0 54 I

  * > 116.0.0.0 204.12.1.254 0 54 I

  * > 117.0.0.0 204.12.1.254 0 54 I

  * > 118.0.0.0 204.12.1.254 0 54 I

  * > 119.0.0.0 204.12.1.254 0 54 I

  * > 155.1.0.0 0.0.0.0 32768 I

  s > 155.1.146.0/24 0.0.0.0 32768 0 I

  * i205.90.31.0 155.1.13.3 0 100 0 200 254?

  *>                  155.1.45.5                             0 200 254 ?

  * i220.20.3.0 155.1.13.3 0 100 0 200 254?

  *>                  155.1.45.5                             0 200 254 ?

  * i222.22.2.0 155.1.13.3 0 100 0 200 254?

  Network Next Hop path metrics LocPrf weight

  *>                  155.1.45.5                             0 200 254 ?

  Rack1R4 (config) #do sh ip bgp neigh 155.1.146.1 opponents

  Rack1R4 (config) #do sh ip bgp neigh 155.1.146.1 opponents

  BGP table version is 18, local router ID is 150.1.4.4

  Status codes: deleted, cushioning d s, history of h, * valid, > best, i - internal.

  r SIDE-failure, stale S

  Source codes: i - IGP, e - EGP,? -incomplete

  Network Next Hop path metrics LocPrf weight

  * > 28.119.16.0/24 204.12.1.254 0 0 54 I

  * > 28.119.17.0/24 204.12.1.254 0 0 54 I

  * > 112.0.0.0 204.12.1.254 0 54 50 60 I

  * > 113.0.0.0 204.12.1.254 0 54 50 60 I

  * > 114.0.0.0 204.12.1.254 0 54 I

  * > 115.0.0.0 204.12.1.254 0 54 I

  * > 116.0.0.0 204.12.1.254 0 54 I

  * > 117.0.0.0 204.12.1.254 0 54 I

  * > 118.0.0.0 204.12.1.254 0 54 I

  * > 119.0.0.0 204.12.1.254 0 54 I

  * > 155.1.0.0 0.0.0.0 32768 I

  * > 205.90.31.0 155.1.45.5 0 200 254?

  * > 220.20.3.0 155.1.45.5 0 200 254?

  * > 222.22.2.0 155.1.45.5 0 200 254?

  Total number of prefixes 14

  Rack1R4 (config) #.

  # and where is the real problem, R1

  Rack1R1(config-Router) #do sh ip bgp

  Version of BGP table is 15, local router ID is 150.1.1.1

  Status codes: deleted, cushioning d s, history of h, * valid, > best, i - internal.

  r SIDE-failure, stale S

  Source codes: i - IGP, e - EGP,? -incomplete

  Network Next Hop path metrics LocPrf weight

  * i28.119.16.0/24 54.1.1.254 0 100 0 54 I

  * > I 204.12.1.254 0 100 0 54 I

  * i28.119.17.0/24 54.1.1.254 0 100 0 54 I

  * > I 204.12.1.254 0 100 0 54 I

  * i112.0.0.0 54.1.1.254 0 100 0 54 50 60 I

  * > I 204.12.1.254 0 100 0 54 50 60 I

  * i113.0.0.0 54.1.1.254 0 100 0 54 50 60 I

  * > I 204.12.1.254 0 100 0 54 50 60 I

  * i114.0.0.0 54.1.1.254 0 100 0 54 I

  * > I 204.12.1.254 0 100 0 54 I

  * i115.0.0.0 54.1.1.254 0 100 0 54 I

  * > I 204.12.1.254 0 100 0 54 I

  * i116.0.0.0 54.1.1.254 0 100 0 54 I

  * > I 204.12.1.254 0 100 0 54 I

  * i117.0.0.0 54.1.1.254 0 100 0 54 I

  * > I 204.12.1.254 0 100 0 54 I

  * i118.0.0.0 54.1.1.254 0 100 0 54 I

  Network Next Hop path metrics LocPrf weight

  * > I 204.12.1.254 0 100 0 54 I

  * i119.0.0.0 54.1.1.254 0 100 0 54 I

  * > I 204.12.1.254 0 100 0 54 I

  * i155.1.0.0 155.1.146.6 0 100 0 I

  * > I 155.1.146.4 0 100 0 I

  * > 205.90.31.0 155.1.13.3 0 200 254?

  * i 155.1.45.5 0 100 0 200 254?

  * > 220.20.3.0 155.1.13.3 0 200 254?

  * i 155.1.45.5 0 100 0 200 254?

  * > 222.22.2.0 155.1.13.3 0 200 254?

  * i 155.1.45.5 0 100 0 200 254?

  Rack1R1 (config - Router) # do sh ip bgp 112.0.0.0

  112.0.0.0/8, version 4 BGP routing table entry

  Paths: (2 available, best #2, table by default-IP-Routing-Table)

  MPIO: eBGP iBGP

  Announced for the update-groups:

  1          2

  54 50 60, (from a customer-RR)

  54.1.1.254 (metric 2560002816) of 155.1.146.6 (150.1.6.6)

  Origin, IGP, 0, 100, valid, internal multipath localpref metric.

  DMZ-Link Bw 250 KB

  54 50 60, (from a customer-RR)

  204.12.1.254 (metric 2560002816) of 155.1.146.4 (150.1.4.4)

  Origin, IGP, metric 0, localpref 100, valid, internal, multipath, best

  DMZ-Link Bw 12500 KB

  Rack1R1(config-Router) #do sh ip route 112.0.0.0

  Routing for 112.0.0.0/8 entry

  Known through 'bgp 100', 200, 0 distance metric

  54, internal type tag

  Last update of 204.12.1.254 ago 00:15:30

  Routing descriptor blocks:

  204.12.1.254, 155.1.146.4, there is 00:15:30

  Path metric is 0, number of shares of traffic 1

  AS hop 3

  Beacon road 54

  * 54.1.1.254, 155.1.146.6, there is 00:15:30

  Path metric is 0, number of shares of traffic 1

  AS hop 3

  Beacon road 54

  Rack1R1 (config - Router) #.

  as you can see, the BGP process in R1 receives the correct link DMZ bw but not indeed take...

  can you please help me if I makeover anything in my setup?

  Hello

  Can you please make sure you have a value of bandwidth on ALL your BGP peering physical interfaces? And you can also include the running-config 'router bgp XXXX' out of R1 as you have not understood what we (others are). Just to make sure that you have "bgp dmzlink-bw' configured on all peerings and overall in the process - it will still show in the output of the same community if it does not work on it.

• RV180 VPN route all internet traffic via IPSec VPN

  Hello

  I install my RV180 to VPN to our headquarters Fortigate 60 C. It works really well

  My only problem is that I don't know how to move internet traffic on our remote site by Headquarters. We want to use this technique so that all sites have the same web content filtering provided by our main Fortigate unit. I see clearly that all traffic destined to our internal network will go trough the VPN tunnel, but internet traffic will go through our modem at the remote site.

  My way of fortigate thinking said that I need a static route to transfer all traffic through the VPN tunnel. I've read elsewhere that I need to set up some sort of ACL.

  Anyone else has any ideas on this / has anyone successfully implemented somehting similar?

  Hi Jared,

  I don't think that RV180 takes complete care of tunneling. Complete tunneling allows you to all your traffic to VPN. RV180 made only split tunneling.

  Thank you

  Vijay

  Sent by Cisco Support technique iPad App

• WRVS4400N will not route all traffic on IPsec

  All my remote sites use various routers to route all their traffic via IPsec.  However, I have a WRVS4400N w/firmware configured 2.0.2.1 with a tunnel of work.  My problem is that I need to define the Group of remote 0.0.0.0 0.0.0.0 so all traffic is forced through the IPsec tunnel and not on the local gateway.  When I make the mistake, Remote Security Group and Local security group cannot be in the same network. However, it works with Cisco/Linksys RV042.

  Any ideas?  Attached are the screenshots of each.

  Transmission of wildcard ESP isn't a feature support, therefore not documented in the product documentation. If you need a wifi router that supports this feature, you can see the series Cisco ISR, which is base IOS.

• Why no implicit route for traffic from IPSec-L2L tunnel?

  In a hub-and-spoke IPSec environment, it is not difficult to implement routing by spoke to the hub.

  But on the side of the hub of a tunnel, where the gateway of last resort for traffic by spoke it, it seems almost counterintuitive than the ACL instructions and even cryptographic doesn't implicitly create a route for the traffic of the station in the tunnel at the end (talk).  It could always be replaced with a static if necessary.

  There is probably a good reason for this, but I can't think of it.  Or am I the only person who thinks it is strange... or maybe an opportunity to feature?

  Hello

  This feature exists and is called reverse road injection. The route is created dynamically (based on ACL Cryptography) and is only available when the SA is up.

  http://www.Cisco.com/en/us/docs/iOS/12_3t/12_3t14/feature/guide/gt_rrie.html

  HTH

  Laurent.

• replication ports 6 VMkernel vSphere

  Thanks to Jeff Hunter for his recent updates and documentation on vSphere for replication 6.0.  Read the docs online, I have a few questions on the vSphere newly supported, dedicated replication VMkernel profits.

  Here (vSphere replication 6.0 Documentation Center) and here (vSphere replication 6.0 Documentation Center) are notes on configuring the VMkernel ports dedicated to the RV on a source host and RV traffic on a target host (one for the VR traffic and another for VR NFC traffic, respectively).

  Considering that it is probably a common practice to use VR as the replication engine with SRM with the intention to fail on the original production site, what is the value in the configuration of two ports VMkernel for VR?

  On the protected Site, you configure a VR VMkernel port to send traffic.  He sends the replicated data from VM for device of recovery of the RV Site, who turns and sends that data replicated for recovery Site ESXi hosts VR NFC VMkernel ports.

  To not return, then the recovery Site can (should?) have an additional port of VR VMkernel, which sends the data replicated VM for device of original VR protected site, which in turn sends the data replicated to the ports of VR NFS VMkernel from the original host protected Site ESXi.

  This looks like it may or must be a distinction between the traffic between the sites and traffic of VR NFC within a site since there are two types of traffic for VMkernel (VR and VR NFC) VR.

  What is this distinction that guarantees a dedicated RV NFC VMkernel port? Why not just use VR VMkernel port? Thank you!

  Edit: I consider these types of traffic to be at the same level of importance and safety.  I have no problem to put two VMkernel ports in the same VLAN.  If I did this, it would put two VMkernel ports per host, in the same network segment.  I wonder why I don't want to do that rather than just use a single VMkernel port or multiple VLANs.

  Post edited by: Mike Brown

  I think it boils down essentially to the options. you don't have to do that, but based on the reviews, it has been estimated that US aircraft enough requests from customers to provide a mechanism which not only allows you to control the path allows the replication traffic (incoming and outgoing) (the source host and VR target devices), and routes it takes on the network but also control the card used for the VR NFC traffic on the target sites. As you RV relies on the NFC to push the data down to the storage of data target on the target sites and some desired customers be able to separate this circulation as well.

  So in the case of the NFC, you can if you want things together (optional) upwards so that the traffic is storage hosts (and I mean here the hosts VR has determined have access to data target stores) can be sent on a physical LAN separated if you wanted that... and a lot of people have asked that flexibility. Allows customers to isolate the common VR NFC (and traffic pass VR) of management traffic not VR "regular".

  Once VRM note that a host has a vmknic marked as RV NFC, only this address is reported on the VR server, which means when it comes to this host in the future that we will only use this address for traffic from VR NFC.

  just my 2cents on why we did it.

• All replication status went to not active after a break of 15 minutes WAN when changing suppliers WAN layer 2

  Last night we put in service to a new provider of services RE because of the costs.  The bandwidth is the same (50mbps), delivery is the same (transfer ethernet fiber) and the network is the same (same IP systems, our routers and roads, control us essentially end points, as a process of transfer of layer 2 etc...).

  The total duration of this judgment was 15 minutes after the hour.  Since this shift, everything on our network works very well except for vSphere replication.  I have 27 VM in our HQ now stuck in not active or not active: RPO Violation status and I cannot get restarted.

  Each site (HQ & DR) there is a virtual machine called vSphere Replication Management Server and vSphere Server Replication.  All 4 of them have been restarted.  Also the DR VCenter server has been restarted.  I just do not restart the server VCenter HQ at this time.

  Still do not get any progress.  Looking at the graph of the bandwidth of the network responsible for the replication interface, I don't see that the strangled 30mbps constant load, we would normally to indicate replication traffic.

  Any ideas how to start replication again?

  Yes the IP network / subnet remained the same on both sites.  We have fixed this problem by resetting all ESXi servers.  Replication is now working normally.

  While the ESXi server could PING the end points, that they can not communicate on the specific ports used for replication.  The only change to the network we did was a slight modification of routing out of our network HQ made us a jump to a different router for the connection upwards the new Wan service provider.  It seems that another linux-based virtual machine must also be restarted to communicate and collect graphs of SNMP traffic to other sites on the WAN again.  It must be a linux thing to require a restart.

  Anyway, problem solved.

• Are thinking of duplication of table to the replication of Vsphere, a quick question

  We currently use Array replication and plan to use the replication of vsphere for flexibility. Unfortunately, we have more than 500 virtual machines to protect - but it is another question and I hope MRS. deploy several devices that will help.

  I can't determine which network interface, the replication traffic goes on:

  1 Hypervizor ports between the ESX hosts (which are 1Gbit in my case) where VMS are?

  2. pushed through vcenter somehow?

  3 Vlan than VR devices are connected to the?

  I have a 10 Gbps link between sites, trying to find how to use more than 1 GB, because the 3 options above are 1Gbit. Although the unit sat on a group of ports that is supported by the host ESX 10Gbit links - but I guess that the only real device of a 1Gbit NIC adapter.

  Hello

  Replication traffic is going:

  1 VR source ESXi server at the remote site via custom protocol LWD (light-weight-delta) TCP ports 31031 and 44046.

  2. outside in VR server via port 902 device and Protocol NFC ESXi host target, then the target data store.

  Separate NICS for VR (isolation of network traffic) replication traffic - to GDL from source ESXi to GDL for server VR application and for inbound replication traffic target ESXi NFC are not available in the current versions, but are part of an RV to come free.

  The VR machine using a NIC vmxnet3

  For the current version, you might want to perform some custom routing/formatting via the ports 31031 (initial full synchronization) and 44046 (all the traffic from replication after the initial synchronization is complete).

  Kind regards

  Martin

• The captain El VPN Internet routing

  I was able to set up a virtual private network and can connect to it. But can not get external ip addresses.

  At one point, I was able to connect to outside the VPN network. I could check my IP to show that I was on my VPN network when I was somewhere else. I don't know why, but at some point it stopped working. The only thing I did at one point was to reboot the machine, but I don't think he was.

  I've followed this how-to:

  https://macminicolo.net/blog/files/setup-a-VPN-server-with-El-Capitan-Server%20. HTML

  Redirection of DNS servers are on 10.0.1.1, 127.0.0.1

  The VPN DNS is set to 10.0.0.1

  After that stuff stopped working, I ran the script:

  bash <(curl -Ls http://git.io/1UlbJQ)

  But that just copy my entires I made by hand, so I deleted everything that has been redone.

  I'm guessing there is something I am missing, or if there is a way for me to check if the routing is or is not happing maybe that would have me idea in how to get this back on track.

  Yes on the client, I send all traffic over VPN set. When you use the VPN, I can not access google.com.

  Nslookup works

  Ping does not work with external areas, also if I ping IP that it doesn't.

  The last time I saw a similar problem here report in these forums it was down the routing tables, as explained below.

  • You have all the traffic of customers being forced to go through the VPN to the office network, I can tell that you are able to communicate with devices on your corporate network
  • However, you can not contacted devices on the Internet once connected via VPN

  It's probably to the fact that your office network is a network firewall on that or Internet router and one of them is the default gateway Internet for your corporate network. So the traffic will go since your Mac client via VPN on the office network, on office of firewall/router network, via the firewall/router to Internet, via Internet on the remote site, then back across the Internet to your router/firewall, then... get lost because your router/firewall knows where to send it to reach your remote Mac VPN client is not on the network of the company.

  What you need to do is add a "static route" tell your firewall/router that all traffic destined to go to the network that you have defined for VPN clients should be "routed" via the VPN Mac server LAN IP address.

  Note: According to the guidelines of Apple VPN clients must be on a beach in separate to your LAN network, so if your LAN is 10.0.1.x/255.255.255.0 then your range of VPN client should perhaps 10.0.2.x/255.255.255.0

• HP Photosmart 5520 series: what ports app to print Basic or advanced within the router?

  It is common for wireless printing open certain application ports in the firewall NAT to router for wireless communications is working properly?

  This was not mentioned during the installion of software, but I found out about it after searching the site of HP support on WiFi printing problems.

  I discovered that my router is blocking traffic on the TCP/UDP #4129 port (id: nuauth) and therefore refused all the print jobs AND ePrint work correctly... ?

  In addition, I needed to add rules for TCP/UDP ports to 9100 and 9220...
  I guess the 9100 (hp-pdl-datastr) is necessary for real communication?

  My router is a Ubee EVW321B.

  Nice interface easy to use, but maybe a bit more protection... ?

  I would like to read if other users did assign certain ports for the 5522 PS works fine on a WiFi connection?

  The here document contains information on port settings for the printer Photosmart 5520.  Your router is not, but he suggested the following for unlisted cases:

  1. If your firewall software is not listed in the table, manually unlock the ports used by the printer.