Router Cisco 1801 for PPPoE Configuration

Similar Questions

• Help setting up a router Cisco 871 for home...

  871

  Hello Andrew,.

  Alain you provided the entire configuration of what you asked, but I think you also need to configure NAT in order to access internet from PC LAN.

  Reason for this is that get you the WAN IP address and default route ISP, for example:

  IP: 10.0.0.1

  Mask: 255.255.255.0

  Gateway: 10.0.0.254

  But your ISP guess you connect only a single PC, so only 10.0.0.1 IP address will have access to the internet. ISP will pass all traffic of 192.168.10.0/24 and 192.168.20.0/24 because these networks are unknown to the ISP. You will need to NAT your internal networks to your WAN IP 10.0.0.1.

  Here is the configuration:

  NAT_ACL extended IP access list

  deny ip 192.168.10.0 0.0.0.255 192.168.10.0 0.0.0.255

  deny ip 192.168.10.0 0.0.0.255 192.168.20.0 0.0.0.255

  deny ip 192.168.20.0 0.0.0.255 192.168.10.0 0.0.0.255

  deny ip 192.168.20.0 0.0.0.255 192.168.20.0 0.0.0.255

  permit ip 192.168.10.0 0.0.0.255 any

  ip licensing 192.168.20.0 0.0.0.255 any

  refuse an entire ip

  NAT_MAP route map
  

  corresponds to the IP NAT_ACL

  IP nat inside source overload map route NAT_MAP interface FastEthernet4

  interface Vlan10

  IP nat inside

  interface Vlan20

  IP nat inside

  interface FastEthernet4

  NAT outside IP

  Last thing, it is not necessary, but maybe you want to prevent users of VLANS to access your internal network:

  Restrict_GUESTS extended IP access list

  deny ip 192.168.20.0 0.0.0.255 192.168.10.0 0.0.0.255

  ip licensing 192.168.20.0 0.0.0.255 any

  refuse an entire ip

  interface Vlan20

  IP access-group Restrict_GUESTS in

  Best regards

  Please note all useful messages and close issues resolved

• Router Cisco 1720 recording not configuration

  I am currently trying to set the configuration for a router in 1720, but I can't get the config to stick. I start up the command line updates all the use of the command "write mem" configurations and then hard reset the router, but when starting BACK I get the initial Configuration of the system dialog box.

  I tried to boot at the rommon prompt and type 'confreg' and following the instructions to keep all the put options or not except this setting

  "turn on"ignore system configuration information? '" "y/n [n]: Y".

  Set to Yes. but when I arrive at the end of the config it just a loop and again with

  "you want to change the configuration? "y/n [n]: Y".

  If I choose Yes it loop if I choose No, it goes back to the rommon prompt. I'm doing something wrong?

  Hello

  reconfigure the router and use it as first order:

  -activate

  t conf

  -config-register 0 x 2102

  -make wr

  -reload

  You should have solved your problem, and then you can complete the configuration and write to startup-config.

  Kind regards.

  Alain

  Remember messages useful rate.

• Configure the router Cisco E2000 wireless for my laptop HP with Vista, I can't work.

  Configure the router Cisco E2000 wireless for my laptop HP with Vista, I can't work.  I spoke with Cisco and they said that my Atheros AR5007 adapter does not work with Cisco E2000 and contact my computer vendor

  Hello

  HM... I guess that the Cisco people know what they're taking everything. The AR5005 is a b/g card and there should be a good reason to not work with a router that is able (the E2000 is able g) g.

  This is HP drivers for the card, http://h10025.www1.hp.com/ewfrf/wc/softwareDownloadIndex?cc=us&lc=en&dlc=en&softwareitem=ob-55737-1

  If you can't make it work, you must decide between a new card or another router.

  Personally, if it's new and I could return it, I'd get a different router model. But YMMV

  ------------

  My posts reflect my understanding and experience. It does not necessarily reflect the opinion or the vision of Microsoft, or anyone else.

  Jack-MVP Windows Networking. WWW.EZLAN.NET

• Where to find the ability auto-raccordement on a router for PPPoE linsys for ADSL connection on request?

  Where to find the ability auto-raccordement on a router for PPPoE linsys for ADSL connection on request?

  Hello

  Use Linksys router information questions.

  Look for the router of the link exact model number.

  http://homesupport.Cisco.com/en-us/support?ICID=global-header-support-link

  See you soon.

• Help to configure the router Cisco 1941

  Help!

  I just bought a router cisco 1941, I understand, it came with the Cisco CP, but I don't know how get you to the part where I can use it.

  Also, how can I connect to the router directly without using the HyperTerminal console, all I want to be able to do is configure the address IP of the ISP and my IP address so I can use it for surfing the internet.

  Help, please.

  Hello

  Thanks for the screenshots and show the output! You will need a few lines of command for CCP to work:

  Configure the terminal

  username username privilege 15 secret PASSWORD

  IP http server

  local IP authentication

  Sent by Cisco Support technique iPad App

• HOWTO configure SSL VPN router Cisco 1941?

  Hello.

  How to configure SSL VPN on a router Cisco 1941? I would like a howto guide that is step by step. I've found myself so far.

  Best regards Tommy Svensson

  Here are a few links that might help:

  http://www.Cisco.com/en/us/products/ps6657/prod_configuration_examples_list.html

  http://security-blog.netcraftsmen.NET/2009/02/Cisco-IOS-SSL-VPN-example.html

• PPPoE Configuration for DSL Speedstream Siemens 4100 b modem

  Hi all

  I created my Windows Vista with my modem in PPPoE session boardband.  I followed the procedures of PPPoE in this forum and Setup successfully.  After the installation, I have Internet browsing but I noticed on a strange thing happens on my DSL modem.  M'semens 4100 B has an internet fluo stedy green if used in a PPPoE session.  The light Internet in my modem turned off which means he drops the PPPoE session.  I wonder if someone could suggest me how activate the PPPoE session on my DSL modem.  I don't know that Setup in the network and sharing for PPPoE boardband mdem Center is right. During the setup session, I choose "Boardband connection WAN Miniport (PPPoE)" and continued.  I don't understand why my PPPoE Internet lignt moden will not be on.

  Thanks for the help and I am very appreciate for all the answers.

  Hi mwb928,

  Normally the PPPoE (point to Point Protocol over Ethernet) power off when authentication failed.

  Ø ensure that your ISP (internet service provider) user name and password are correct

  O ensure that the connection is set to obtain an IP (internet protocol) address and an address of server DNS (Domain Name System) automatically under network and sharing Center, see link below steps:

  Change TCP/IP settings

  http://Windows.Microsoft.com/en-us/Windows-Vista/change-TCP-IP-settings

  For more information, see the link below

  Create a PPPoE Internet connection

  http://Windows.Microsoft.com/en-us/Windows-Vista/create-a-PPPoE-connection-to-the-Internet

  You can check for known problems with Siemens

  http://support.Automation.Siemens.com/WW/llisapi.dll?Func=cslib.csinfo&lang=en&objid=10805406&SubType=

  Thank you, and in what concerns:

  Ajay K

  Microsoft Answers Support Engineer

  Visit our Microsoft answers feedback Forum and let us know what you think.

• WCG200 & WRT54GS together for internet configuration problems

  OK I wil l provide as much information as I can here. First of all, the problem is that until the other day I've used DSL and now switched to comcast cable.  As such, I went and bought the wcg200 cable modem only to find out that there seems to be problem there with the firmware wireless.  Before buying the wcg200, I still have a wireles g Linksys WRT54GS.  Now, I just want to use the modem cable as an internet modem and continue to access everything I got via the 54gs wireless router and cannot find out how to configure the 54gs.

  Here is the TRICK so far.  When I restart my computer my default gateway is 192.168.1.1, which is the 54gs and I don't get any INTERNET CONNECTION.

  If I have enough IPCONFIG RENEW it switches to 192.168.1.2, and I get INTERNET & life is the way it has been.  Power down the pc and the re-boot and I'm back to 1.1.  Please don't tell me that I have create a .bat file to include in the boot to release and renew.  I'm sure it's a setting somewhere on the 54gs to have this work wireless, but use the wcg200 gateway.

  The cables are as follows:

  -patch cable cat5 wcg200 port 1 to port 1 on 54gs

  -wire cable from my computer to port 1 of 54gs until I can get this to work.

  -I can ping 192.168.1.1 which is 54gs & 192.168.1.2 = wcg200

  Currently on the wcg200:

  -DHCP is on

  -IP address is 192.168.1.2

  -IP from de.1.100 for 50

  -Wireless is disabled

  -Everything is disabled except for the firewall, multicast and porscans, these are the default values for security.

  -Everythign else is default

  -upnp disabled

  -firmware is 2.0.3.5.10 - 0425

  ON THE WRT54GS

  -J' deleted the PPPoe configuration.

  -IP address is 192.168.1.1

  -DHCP is also on (it can not be good)

  -wireless is on with - wep

  -block the anonymouse applications internet is on

  -multicast filter is on

  -filter idnet port 113 is on

  -upnp enabled

  THX

  Snowman777

  Option 1: You still use the WCG200 gateway router and the WRT as simple access point. You almost have it. All you have to do is to disable the DHCP server on the WRT. Only the WCG is the gateway router and the DHCP server on the WCG gives correct gateway IP address. The WRT connects customers with wireless local area network. Internet settings on the WRT-related (e.g. the type of internet connection, filter, blocking, upnp, transfer/port triggering, etc.) are not all relevant because these functions have meaning only if the internet connection is connected to the internet port of the WRT. You probably want to disable the wireless in the WCG radio, if you don't want to use it.

  Option 2: Transform the WCG in a modem, or disable routing all and NAT. disable the DHCP server on the WCG. Then, on the Administration - Advanced page there is the option to turn off 'Routing and NAT '. This disables the functions of routing and makes the WCG in a standard modem. So disable Routing & NAT. You will lose the connection to the WCG.

  Now, you reconfigure the WRT: you open the web interface http://192.168.1.2/ enable the DHCP server (or better leave it turned on). Set the type of internet connection on automatic/DHCP. If you wish you can put the WRT default 192.168.1.1 IP address. Save the settings. Now, cable wires of the WCG in the internet port of the WRT. The WRT must now use the WCG as modem and gets his audience to the internet IP address of your ISP. You can check on the status of the WRT page. Now it should show an IP address instead of the 0.0.0.0 that you see if you connect the WRT by port 1 for the WCG. Make sure that your computers renewal DHCP IP address either by restarting or by entering "ipconfig / renew *" as an administrator in a command prompt window.

  That's all.

  A note: according to the manual of the WCG will be internal IP address 192.168.100.1. If you need to make changes on the WCG once again, you must either set up a static IP address on a computer inside the 192.168.100. * with the subnet mask 255.255.255.0 and connect the computer directly to the WCG or you simply press the reset of the WCG for 30 seconds to reset. Then the WCG is back to 192.168.0.1 with active DHCP server, i.e. you can connect a computer directly to the WCG, it gets a valid IP address to connect to the WCG and you can make changes again.

• Router Cisco 1941 - crypto isakmp policy command missing - IPSEC VPN

  Hi all

  I was looking around and I can't find the command 'crypto isakmp policy' on this router Cisco 1941.  I wanted to just a regular Lan IPSEC to surprise and Lan installation tunnel, the command isn't here.  Have I not IOS bad? I thought that a picture of K9 would do the trick.

  Any suggestions are appreciated

  That's what I get:

  Router (config) #crypto?
  CA Certification Authority
  main activities key long-term
  public key PKI components

  SEE THE WORM

  Cisco IOS software, software C1900 (C1900-UNIVERSALK9-M), Version 15.0 (1) M2, VERSION of the SOFTWARE (fc2)
  Technical support: http://www.cisco.com/techsupport
  Copyright (c) 1986-2010 by Cisco Systems, Inc.
  Updated Thursday, March 10, 10 22:27 by prod_rel_team

  ROM: System Bootstrap, Version 15.0 M6 (1r), RELEASE SOFTWARE (fc1)

  The availability of router is 52 minutes
  System returned to ROM by reload at 02:43:40 UTC Thursday, April 21, 2011
  System image file is "flash0:c1900 - universalk9-mz.» Spa. 150 - 1.M2.bin.
  Last reload type: normal charging
  Reload last reason: reload command

  This product contains cryptographic features...

  Cisco CISCO1941/K9 (revision 1.0) with 487424K / 36864K bytes of memory.
  Card processor ID FTX142281F4
  2 gigabit Ethernet interfaces
  2 interfaces Serial (sync/async)
  Configuration of DRAM is 64 bits wide with disabled parity.
  255K bytes of non-volatile configuration memory.
  254464K bytes of system CompactFlash ATA 0 (read/write)

  License info:

  License IDU:

  -------------------------------------------------
  Device SN # PID
  -------------------------------------------------
  * 0 FTX142281F4 CISCO1941/K9

  Technology for the Module package license information: "c1900".

  ----------------------------------------------------------------
  Technology-technology-package technology
  Course Type next reboot
  -----------------------------------------------------------------
  IPBase ipbasek9 ipbasek9 Permanent
  security, none none none
  given none none none

  Configuration register is 0 x 2102

  You need get the license of security feature to configure the IPSec VPN.

  Currently, you have 'none' for the security feature:

  ----------------------------------------------------------------
  Technology-technology-package technology
  Course Type next reboot
  -----------------------------------------------------------------
  IPBase ipbasek9 ipbasek9 Permanent
  security, none none none
  given none none none

  Here is the information about the licenses on router 1900 series:

  http://www.Cisco.com/en/us/partner/docs/routers/access/1900/hardware/installation/guide/Software_Licenses.html

• client vpn Cisco router cisco 880 - Private ip addresses is not only the public ip

  Experts,

  I have an interesting question, I am able to authenticate and connect to my to my Cisco880K9 router cisco vpn client.

  My internal network is: 10.10.1.0

  My Pool of IP VPN is: 10.10.2.2 - 10.10.2.250

  My external Public ip address is: 192.198.46.14

  When I connect with my vpn client I get my vpn 10.10.2.2 pool address.

  IF I ping my server 10.10.1.2 I get a response from my public IP address.

  Example:

  Ping 10.10.1.2 with 32 bytes of data:

  Reply from 192.198.46.14: bytes = 32 time = 45ms TTL = 127

  Reply from 192.198.46.14: bytes = 32 time = 50 ms TTL = 127

  Reply from 192.198.46.14: bytes = 32 time = 42ms TTL = 127

  Reply from 192.198.46.14: bytes = 32 time = 45ms TTL = 127

  I enclose my config file. It's almost a copy from the following link:

  http://www.Cisco.com/en/us/products/sw/secursw/ps2308/products_configuration_example09186a00801c4246.shtml

  Thanks for the help

  Please please configure NAT exemption as follows:

  access-list 120 deny ip 10.10.1.0 0.0.0.255 10.10.2.0 0.0.0.255

  access-list 120 allow ip 10.10.1.0 0.0.0.255 any

  IP nat inside source interface FastEthernet4 list 120 overload

  no nat ip within the source list 1 interface FastEthernet4 overload

  Then, disable the translation: claire ip nat trans *.

• Series router Cisco 2700 adding to monitoring

  Hi all
  
  First of all, I'm quite new to Hyperic. I only got it up and running for a day now and I must say I am impressed if done well for developers!
  
  This is my problem:
  I have a number of Cisco routers that are SNMP v2 enabled and configured. I know that they can give me SNMP values because I currently use CACTI to monitor and chart of their statistics. (Running IOS.)
  
  I'm slowly moving away from cactus to Hyperic (and); That's why I want Hyperic to monitor servers and network devices.
  
  I can easily add servers in Windows 2K3R2 no problem and I am currently monitoring services MSSQL/MYSQL/APACHE 2.2.x for now.
  
  I followed the instructions: http://support.Hyperic.com/Confluence/display/DOCSHQ30/Cisco+IOS
  
  I don't use a FULL domain name for our routers so I just add the IP address of it.
  I select the platform Type = Cisco IOS
  I choose the Hyperic Agent on the Hyperic Server (so it will read 127.0.0.1:2144)
  
  Hyperic adds the router correctly.
  I click on MONITOR and click Properties of the router configuration
  I add the string SNMPCommunity (I know works like its used with Cacti)
  I'll leave the v2c SNMPVersion
  And let interfaceIndex ifDESCR (I tried all the options ifname, ifalias as well)
  The SNMPPort, I leave as 161 (I know it works as it works with the cactus).
  I click OK
  
  I wait a few seconds and Hyperic bounces an error failed:
  
  The configuration has not been set for this resource due to: invalid configuration: error communicating with resources: unable to connect to the SNMP Agent (v2c 127.0.0.1:161, < my snmp community string >)
  
  What I am doing wrong? Help!
  
  Thanks in advance.
  
  PS - I am VERY impressed on how it was easy to configure Apache/MSSQL/MySQL monitoring. And how AD/monitoring server is supported on the box (and how easy to set up.)
  
  -Pete

  Hi Pete,.

  the errormessage
  ' The configuration has not been set for this resource due to: invalid configuration: error communicating with resources: unable to connect to the SNMP Agent (v2c 127.0.0.1:161,).

  indicates that you has not changed the router default ip 127.0.0.1 to the actual ip address address.
  Please go to your Cisco 2700 platform-> inventory-> Configuration properties and to adapt the 'snmpIP' to your needs.

• Cisco Aironet 2600 series Configuration of the DHCP server is NOT serving addresses?

  Cisco Aironet 2600 series Configuration of the DHCP server is NOT serving addresses?

  I have (2) AIR-SAP2602I-A-K9, configured the same way.

  on two different remote LANs.

  They don't seem to be handing out addresses via DHCP.

  {If I connect to a local network with another DHCP server}

  wireless devices can obtain addresses

  This another DHCP server on the LAN through the access point.}

  I followed 12.4.25d. JA.cg.pdf

  Configuration of the Access Point to provide the Service DHCP 5-22

  ---------|---------|---------|

  e.g. 3444-RCS1-AN #show running-config

  Building configuration...

  version 15.2

  3444-RCS1-YEAR host name

  no ip Routing

  USH - DM IP domain name

  DHCP excluded-address IP 192.168.29.89

  IP dhcp RCS1 pool

  network 192.168.29.88 255.255.255.248

  router by default - 192.168.28.1

  Rental 1 0

  interface BVI1

  IP 192.168.28.211 255.255.254.0

  no ip route cache

  default IP gateway - 192.168.28.1

  ---------|---------|---------|

  ---------|---------|---------|

  e.g. 3444-RCS2-AN #show running-config

  Building configuration...

  version 15.2

  3444-RCS2-YEAR host name

  no ip Routing

  USH - DM IP domain name

  DHCP excluded-address IP 192.168.129.81

  IP dhcp RCS2 pool

  network 192.168.129.80 255.255.255.248

  router by default - 192.168.128.1

  Rental 2 0

  interface BVI1

  IP 192.168.128.171 255.255.254.0

  no ip route cache

  default IP gateway - 192.168.128.1

  ---------|---------|---------|

  Thats the DHCP Pool range 192.168.29.88 through 192.168.28.95

  Well this will confuse your customers.

  And this is NOT how to set up your "range".   See below:

  DHCP excluded-address IP 192.168.29.1 192.168.29.87

  DHCP excluded-address IP 192.168.29.96 192.168.29.254

  IP dhcp RCS1 pool

  network 192.168.28.211 255.255.254.0

  router by default - 192.168.28.1

  Rental 1 0

• LDAP AAA for VPN configuration

  Preface: I'm all new to Cisco Configuration and learn as I go.

  I'm at the stage of configuration LDAP to configure a VPN on ASA 5520, software release 8.3 (1).  Previously the programme installation and RADIUS authentication successfully tested, I tried to use similar logic to implement the LDAP authentication/authorization.  I have acquired a service account that queries the pub for the identification of the registered user information.  My main resource was the following Manual: Cisco ASA 5500 Series Configuration Guide using the CLI Software Version 8.3.  I did initially configurations by using ASDM, but could not get tests to succeed.  So I amazed the ASDM configs and went to the CLI.  Here is the configuration.

  AAA-server AAA_LDAP protocol ldap
  AAA-server host 10,20,30,40 (inside) AAA_LDAP
  Server-port 636
  LDAP-base-dn domain.ad
  LDAP-scope subtree
  LDAP-naming-attribute uid
  LDAP-login-password 8 *.
  LDAP-connection-dn cn = commonname, OU = ou01, or = ou02, dc = domain, dc = ad
  enable LDAP over ssl
  microsoft server type
  LDAP-attribute-map LDAP_ATTRIB

  ---

  type tunnel-group ASA_DEFAULT remote access
  attributes global-tunnel-group ASA_DEFAULT
  authorization-server-group AAA_LDAP

  ---

  LDAP attribute-map LDAP_ATTRIB
  name of the MemberOf IETF Radius-class card
  map-value MemberOf "VPN users' asa_default

  ---

  I tested all the naming-attribute ldap alternatives listed with the same results.

  When I test the authentication using this configuration, I get the following error: ERROR: authentication server does not: AAA Server has been deleted

  When I test authorization using this Setup, I get the same error (except for the word permission instead of authentication).

  I am at a total loss.  Any help would be appreciated.

  I would use ldp.exe to see if you can make sure that the sytnax of your ldap-connection-dn is just as you have in your config, it really helps just copy and paste.

  The problem I see is the following:

  [210] link as st_domadm
  [210] authentication Simple running to st_domadm to 10.20.30.30
  [210] simple authentication for st_domadm returned credenti invalid code (49) als
  [210] impossible to link the administrator returned code-(1) can't contact LDAP er

  I suppose your ldap-connection-dn is st_domadm and you try to test with the administrator account?

  Thank you

  Tarik

• Connection Cisco SG300-10-Core Cisco 6513 for ShoreTel phones

  I have a new ShoreTel phone system will soon.  Configure a dhcp, including option 156 scope which is required for ShoreTel to obtain the configuration on ShoreTel phones and in order to get on the vlan correct voice on the phone.  I also created a new vlan 112 for the vlan voice.  When I plug directly into the Cisco 6513 Core switch, the phone starts fine, it gets its configuration and on the VLAN correct 112.

  We have a training room in which there will be a lot of users.  I ordered 6 Cisco small business 10port SG-300 POE switches for this training room.  I plugged the switch in a cable coming off the 6513 which is just an access port and in the vlan voice I created for phones shoretel VOIP:

  interface FastEthernet10/11
  switchport
  switchport mode access
  switchport voice vlan 112
  priority queue queue-limit 20
  WRR-queue random - detect min-threshold 1 30 40 50 60 70 80 90 100
  WRR-queue random - detect min-threshold 2 30 40 50 60 70 80 90 100
  WRR-queue random detection threshold min 3 30 40 50 60 70 80 90 100
  WRR-queue random detection max-threshold 1 70 80 90 100 100 100 100 100
  WRR-queue random detection max-threshold 2 70 80 90 100 100 100 100 100
  WRR-queue random detection threshold 3 70 80 90 100 100 100 100 100 max
  WRR-queue cos-map 1-3-1
  WRR-queue cos-1 6 4 map
  WRR-queue cos-map 2 6 0
  WRR-queue cos-map 2 8 2
  WRR-queue cos-map 3 1 7
  WRR-queue cos-map 3 8 3 6
  MLS qos trust dscp
  Storm-control broadcasts 20 h 00
  spanning tree portfast

  When I plug a phone directly into this cable the phone works very well.  When I plug a cheap cisco POE switch in I can get 3 phones works very well, but due to the amount of energy needed for this cheap a cisco switch it will give only 3 phones power.

  The real problem here is plug into small business cisco SG300-10port POE managed switch.  I thought I could just connect the switch to the port configured above right out of the box and plug in phones without a problem.  When I plug the switch and start plugging in ShoreTel phones, they do not start coming in and upward and actually had a few phones upward but then finally there is no tone and also later, they appear on the screen as a service not available.

  I have to configure a trunk port on a port on the SG300 and the Cisco 6513 for this to work?  Also I will need to VLAN configuration manually on the SG300.  Looks like that when I just plugged it in to the above configured the port on the SG300 it automatically create the vlan 112.

  Any help would be appreciated

  Thank you

  Dave

  Deleted