Router-on-a-stick VLAN possible with SRP547w & SG200-26?

Similar Questions

• Router-on-a-stick with RVS4000

  Hi all

  I intend to reshape our network topology and the creation of at least three VLANs using a router-on-a-stick of the installation type. We have two switches Cisco Small Business sg200-50 and a small RVS 4000 router business. I haven't implemented the configurations of router-on-a-stick in IOS, but I was unable to figure out if it is possible to do with small business of operating systems on the router and switches, we have. Does anyone have an experience with this? It is even possible with the equipment of small businesses?

  Sorry if this question is already answered elsewhere on the forums; I searched around, but can't find anything.

  See you soon,.

  Curtis

  Hi Curtis,.

  Without having the RVS4000 in front of me, it looks like you can. I suppose that you have several VLANs on your SG200 and want to route between them as the SG200 is only a layer 2 switch. You can connect the RVS 4000 via trunk on the switch and the router port (its in L2 Switch-> vlan configuration of the port on the rvs4000) and add each vlan of the trunk (under L2 switch-> belonging to a vlan on the rvs). Please note that the RVS4000 is limited to 4 virtual local networks, including the vlan by default. I think that the router will automatically create the static routes appropriate when you create them VLAN (vlan create a L2 Switch->). The default value on the RVS4000 is for intervlan routing be enabled under Setup-> routing advanced but double check if you encounter any problems. Also, check the routing table and add static routes as needed.

  You can also switch a switch to a SG300, which is a layer 3 switch.

  Best,

  David

  Do not forget to note resonses useful and identify the right answers.

• ____2. I have Windows Vista Home edition is possible with Windows XP prof sp2 Remote Desktop connection? __othervise how?

  • I can't share internet and file simultaneously? If I share internet file sharing and disappear on the other PC if I share folder and run I can't share internet...
  • 2. I have Windows Vista Home edition is possible with Windows XP prof sp2 Remote Desktop connection?
  • othervise how?

  Remote Desktop connection is not available in Vista Home: http://www.howtogeek.com/howto/windows-vista/turn-on-remote-desktop-in-windows-vista/.

  I need more info on how your network is configured to answer the question on the other.  How is the computer connected to the internet?  It connects wireless or cable to the router or modem or through ICS from another computer or what?  How do you change between the sharing of internet connection currently?  What happens when you try to enable both connections at the same time (or do not have two connections)?

  Thank you.  The answers above, I can be able to understand the problem, because right now I really don't know how you setup and I need as much information as you can provide about it.

  Good luck!

  Lorien - MCSA/MCSE/network + / has + - if this post solves your problem, please click the 'Mark as answer' or 'Useful' button at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• 2 VLAN ACL with what Miss me

  Thanks for reading.
  

  This topology consists of one 6224 and two 2824 Powerconnect switches.
  

  Right now, we're looking to build two VLANs, routed, sharing a small range of IPs on VLAN 20.
  

  Also want to route out to the interwebz for both nets. Do I need a third vlan for that?
  

   Presumably one for each actual route out I would think.
  

  I've entered the following commands into the 6224.
  

  - -
  

  confvlan databasevlan 10vlan 20exitinterface vlan 10ip address 192.168.1.1 /24ip access-group 'BUSINESS'name SALESroutingexitinterface vlan 20ip address 172.16.1.1 /24ip access-goup 'SALES'name BUSINESSroutingexitip access-list SALES permit ip 192.168.1.0 0.0.0.255 anyip access-list SALES permit ip 172.16.1.0 0.0.0.255 anyip access-list BUSINESS permit ip  172.16.1.204 0.0.0.7 anyip access-list BUSINESS permit ip 192.168.1.0 0.0.0.255 anyinterface range 1/g9-1/g16 ---these are untagged in both Vlan 1 and vlan 10switchport mode access each has a PVID of 1 in both Vlans??switchport access vlan 10exitinterface range 1/g17-1/g24 ---these are untagged in vlan 20switchport mode access PVID of 1 or 20 neither changes anythingswitchport access vlan 20exitip routing
  

  - -
  

  From VLAN 10 on the 6224 , all addresses in VLAN 10 and 20 can be pinged.
  

  From VLAN 20 on the 6224 all addresses in VLAN 10 and 20 can be pinged,
  

  2824-1 is connected via its port 24, (a member of vlan 20 in switchport mode access)
  

  to port 24 on the 6224.
  

  Port 1/g23 on 2824-1 is connected to a host at 172.16.1.240. that host can  ping nothing
  

  beyond 172.16.1.1. But if I plug both the switch uplink and the host to a Cisco 3524xl in factory defaul
  

  I can ping everyhthing on the 172.16.1.0 /24 subnet right across the uplink. I'd like to at the least
  

  get help on what the issue is with the pings from the 2824.
  

  The ACLs aren't actually in play but they are intended as part of the config.
  

  thanks in advance for your help.
  

  I think you're on the right track, leave the configuring ACLs for now. Once we have connectivity, then add them in.

  With the connections between the two switches, we use mode Trunk/general instead of the access mode.

  If the 6224 performs the Routing and connects to your external connection. While the connection must have its own dedicated VLAN. The 6224 also has a static route in place, helping to direct traffic on.

  Here's a post with some info to look over.

  en.Community.Dell.com/.../19506015.aspx

  Keep us updated.

  Thank you

• IOS router VPN Client (easy VPN) IPsec with Anyconnect

  Hello

  I would like to set up my router IOS IPsec VPN Client and connect with any connect.
  Is it possible to configure an IPSec and SSL VPN Client on IOS router? I use for example a 1841.

  It would be perfect to give the user the choice of SSL or IPSec protocol. And the user needs that the Anyconnect Client.

  I think it's possible with a Cisco ASA. But I can also do this with an IOS router?

  Please let me know how if this is possible.

  Also is it true that the IOS routers are not affected to hear bug bleed? SSL VPN and SSL VPN with Anyconnect page is also save?

  http://Tools.Cisco.com/Security/Center/content/CiscoSecurityAdvisory/CIS...

  But I am in any way interested in using IPSec and SSL VPN on a router IOS...

  It's true - CCP does not yet offer the options to configure a VPN IPsec with IKEv2.

  The configuration guide (here) offers detailed advice and includes examples of configuration.

• Catch 22 - Port Trunk Configurations: how to combine identifiers VLAN native with DHCP (but allows traffic of VM)

  Catch 22 - Port Network Configurations: how to combine identifiers VLAN native with DHCP (but allow the virtual computer)

  I came across a Catch 22.  Maybe someone can restore the directly here.  I found a "witch hunt" for sure.

  It comes with the Ports of junction on the side of the switch of the ESX host network.

  Context:

  Ok. The Setup is a HP Blade C7000 enclosure.  I try to configure ports for switching to the blades.  ESX 3.5 U4 will be installed the BL460cs.  Installation is preferred method: revive unattended.  No problem with the syntax of Kick-Start,

  I am here, it's the side network.

  The problem:

  I find a major complication in that the switch ports must be configured for both traffic Service Console and VMkernel, more Virtual Machine since only two NICs by blade. Not best practices, but we have only two switches Cisco 3020 inside.  The two uplink physical NIC is paired in the same vSwitch.  (No iSCSI does fortunately).

  So the Catch 22 question is as follows:

  If the id VLAN native set up on the switch port, DHCP works of course and the VMware boot loader is able to grasp a binary / packets on the network (FTP Site) and install OK.  But after no installation, no communication with SC unless I set the VLAN id of the SC to '0 '.  The value "4" 0 does not communication, but "40" is the VLAN native.

  If id configuring VLAN native retired from the Switch port, DHCP will not work and host does not have IP address during the VMware boot process.  This is as expected as traffic without label is not assigned an eligible

  VLAN, so no comms.

  The Port of the Switch configuration:

  interface GigabitEthernet0/16

  SERVERNAME description

  switchport trunk encapsulation dot1q

  switchport trunk vlan native 40

  switchport trunk allowed vlan 40-254

  switchport mode trunk

  switchport nonegotiate

  Speed 1000

  No cdp enable

  spanning tree portfast trunk

  end

  Summary

  OK, let's summarize where things are and if possible please attach responses to their digital identity.

  (1) is there a way to delete the VLAN tagging altogether side ESX host? Not only the id '0 '. The problem is with clearly with the VLAN native defined as "40".  If "40" IDs specified on the Group of ports for the Service Console, no joy, no comms. If the id of '0' value, capable of ping gateway and communicate on the network.

  (2) what is the problem with the definition of VLAN native as "40" when the config for the switch port is set as VLAN native "40"?  Or if it was a problem?  Both parameters clearly do not work together.

  (3) a switch receiving a unmarked frame it will assign to the VLAN Trunk native. Ok. Trunking bases and why I need a VLAN specified on the port for DHCP native work.  But it seems that since the id VLAN is set manually even as VLAN native, closed communications and no traffic as possible.

  (4) executives made tag 802. 1 q VLAN native?  I think that it is not and this could well be the problem. Since the id VLAN "40" is not labeled, but try to score the side host vSwitch port group.

  Please let me know your thoughts, community and how in general, we are approaching 2 NIC ESX configurations.

  When trunking multiple VLANs, you either have a default VLAN is nothing is tagged, or you don't.  That's what the vlan native to you, it defines which VLAN would be used if no tag is visible on the packets traversing the network.  For servers, if you are marking, then everything has to tag, if you're not marking at the server level, then the port must be either an access port or a VLAN native or default must be set.  I also don't keep your service console the same network as your vm.  Keep this isolated for the security of the network.  If you isolate this VLAN, you can separate and use a single IP address for installation and one for post construction.

  Or, you can provide an IP address during the build.

  -KjB

  VMware vExpert

• I have a Mac Book Pro with a CD/DVD drive.  I want to copy a home made DVD.  Is this possible with iMovie or another application?

  I have a Mac Book Pro with a CD/DVD drive.  I want to copy a home made DVD.  Is this possible with iMovie or another application?

  Look for the hand brake.

  It is a free application which can convert your DVD to QuickTime formats.

• On the new Apple TV 4th generation, can I turn off bluetooth as possible with the 3rd generation?

  Hi, on the new Apple TV 4th generation, can I turn off bluetooth as possible with the 3rd generation?

  I don't think it is necessary for the remote control of Siri.

• I wish that the tabs colorful. is it possible with Firefox? And or each new topic have a different color tab.

  I wish that the tabs colorful. is it possible with Firefox? And or each new topic have a different color tab.

  The ColorfulTabs extension can be useful for you.

• Is it possible with the serial number of an Xserve to read the configuration and the year of production?

  Is it possible with the serial number of an Xserve to read the configuration and the year of production?

  This will show you the model and year: https://checkcoverage.apple.com/

  If a specific configuration (like the 1 TB disk instead of 500 GB for ex) will not be determined. You can only learn by starting the Xserve (or open and look into it.)

• Is this possible with the 6 having touch 3D iPhone

  Is this possible with the 6 having touch 3D iPhone

  Is there anyone to answer my question pl

• Dictation of texts long is possible with an iMac?

  I have to dictate texts long very often. Is this possible with an iMac? What do need me for this? The quality-related experiences?

  The Mac OS fact have the ability to dictation built in but I find it annoyingly inaccurate even in more precise mode. When I use it, I find I have to correct several errors, usually involving misunderstood words and some very strange kinds of mistakes as well. In General, I can type faster that I can dictate and correct.

• DTS - HD and Dolby TrueHD audio via HDMI or S/PIDF. Is this possible with HPE-140sc?

  I have an audio DTS - HD and Dolby TrueHD via HDMI or S/PIDF of blu - ray movie? I request because the Nvidia homepage not listed this support function for gtx260 (http://www.nvidia.com/object/3d-vision-requirements.html) and the homepage of Reatek'a is the same for ALC888S (http://www.realtek.com.tw/products/productsView.aspx?Langid=1&PFid=28&Level=5&Conn=4&ProdID=141).  What kind of problems is if there is no support in the HPE-140sc for Dolby TrueHD or DTS - HD audio? 3D-Cinema compatible reading is necessarily I can't find reading compatible sound card 3d video. Is the cheapest solution in this case buying gtx460 if I want to get DTS - HD and Dolby TrueHD audio?

  Pether, I don't think it's possible with the GTX260.

• Is it possible with us an axis in Max?

  Is it possible with us my axis Max?  I use a card PCI-7340.  I looked in the Interactive tab 1 d and I don't see an option to run a command of homers.

  No, direct debit is not implemented in MAX. Please use the API OR-Motion and LabVIEW, or any other programming language to run a movement of reference.

  Kind regards

  Jochen

• Possible with Windows Live Movie Maker 7 chapters?

  I am doing my first project. I would like to have a main menu with chapters like on a real DVD. Is this possible with a true WLMM? If so, how? Thank you!

  Hello

  You can follow the links below and check if they help you accomplish what you want.

  http://Windows.Microsoft.com/en-us/Windows7/products/features/Movie-Maker

  http://Windows.Microsoft.com/en-us/Windows7/use-custom-settings-to-save-a-movie-in-Windows-Live-Movie-Maker

  http://www.Microsoft.com/education/teachers/guides/Windows_Movie_Maker.aspx

  If the above given links don't work then you can publish your application in the Windows Live Solution Center.

  http://www.windowslivehelp.com/product.aspx?ProductID=5

  Hope this information is useful.

  Amrita M

  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.