Router RV130W + SG92 - 24 Switch problems

Similar Questions

• EIGRP running between the router and ASA by switch

  Hello

  Is that possible I can running an EIGRP between router and ASA by switch?

  Router and ASA connected to the switch with static route.

  Hi Tommy Chin.

  It is possible, we must advertise to the route between the router and ASA.

  Please provide your connectivity diagram to better explain.

  For example...

  interface GigabitEthernet0/0

  Description links to WAN router

  nameif OUTSIDE

  security-level 50

  IP 10.1.1.1 255.255.255.192 ensures 10.1.1.2

  Summary-address eigrp 100 10.1.0.0 255.255.0.0 1

  !

  Confiuration Protocol EIGRP

  standard access list eigrpACL_FR allow a

  !

  Router eigrp 100

  eigrpACL_FR distribute-list in the interface outside

  neighbor 10.1.1.3 OUTSIDE interface

  neighbor 10.1.1.2 OUTSIDE interface

  Network 10.1.1.0 255.255.255.192

  redistribute connected

  redistribute static

  !

  Kind regards

  Srinivas.

  Note: if it solves your problem it mark it as resolved.

• NAT router 1841 and 3550 switch help

  Hi experts, I need some help with setting up a network.  Network diagram is attached.

  I created 3 VLANs on the 3550 Switch and activated InterVLAN Routing.  I can't do a ping from one VLAN to another.  I've added static routes to networks VLAN on the router.  Is the only part I'm not sure where and how configure NAT?  For example, if it was just a standalone router Cisco 1841 I would just create list of access and NAT FA 0/0 outside and FA 0/1 on the inside.  It would be great if someone can give me an example or point me to the right direction.

  Router ISP--> Cisco 1841--> Switch Cisco 3550

  Cisco 1841 router:

  FA 0 / 0--> WAN Interface

  IP address: 30.20.10.2

  FA0 / 1 Interface LAN connected to the 3550 switch-->

  IP address: 10.0.0.1/24

  Cisco 3550 switch:

  FA 0 / 24--> to connect to the Cisco 1841 router

  IP address--> 10.0.0.2/24

  FA 0/1 - 0 / 10--> VLAN 1

  FA 0/11 - 0 / 20--> VLAN 2

  FA 21/0 - 0 / 23--> VLAN3

  Thank you

  Hello, it's the same thing, but in your access list, you need allow all of your internal address ranges. On your router and 3550 make sure routing everything is OK, you say you have connectivity.

  This means that your network 10 should be able to get to your 192 networks and vice versa.

  On your 3550, you can have a default route to the router. And your router should have roads to 192 networks via the address 10 of the 3550.

  Then the NAT configuration

  Int fa0/1
  IP NAT inside

  Int fa0/0
  NAT outside IP

  IP access-list standard MYNAT
  Permit 10.0.0.0 0.0.0.255
  Permit 192.168.1.0 0.0.0.255
  Permit 192.168.2.0 0.0.0.255
  Permit 192.168.3.0 0.0.0.255

  And then in your NAT statement

  IP NAT inside source list MYNAT interface fa0/0 overload

  Hope this helps

  Sent by Cisco Support technique iPhone App

• LAN N450 connection through a switch problem

  I replaced my router from Time Warner Ubee with a Netgear N450. I have 2 desktop computers and TV and PS3 in my basement that is connected to a Netgear GS108 switch 8 gigabit ports. Everything worked fine until I swapped the router. All my wireless devices work and the office in our head office that is connected directly to the N450 work. A desktop running Win XP Pro, the other works under Win 7. I don't get "LAN was not a valid IP configuration errors. I rebooted everything, turn off DHCP and tried to manually enter the IP information, power off the pc from the wall outlet, etc. and spent several hours on researching this issue. Any ideas would be useful.

  Problem solved. I brought the Win 7 PC upstairs and connected directly to the router. The PC immediately recognised and connected to my home network. Then, in order to eliminate potential problems with the switch itself or wiring, I brought the upstairs switch and connected between the router and the PC Win 7. Same results as above - connected to the network home and Internet. Took everything back down and voila - both PC is now successfully connected to the host and the internet using DHCP network automatically. Not sure why it worked. I went through this simple process to diagnose potential hardware issues.

• Switchport access and trunk on Layer 3 switch problems

  Hi all

  I was building a network design just for practice and I came across a problem that I didn't understand. Can someone please help. I have attached a picture to clarify things.

  Please let me know if you need information to answer my question. Thank you

  Francis

  Yes the router on a stick. However only vlan 100 is necessary because you have between multilayer switch and router ospf.

  Please don't forget to rate and select the correct answer

• Language on macOS Sierra switch problem

  I just upgraded to macOS Sierra and I have a problem with switching languages.

  I have both English and Russian, but I just need to do the Cmd + space to more than an hour to change language and when I do, I can get the American icon in the status bar, but the language is passed to the Russia and vice versa.

  Any thoughts on how to solve this problem?

  Is this another discussion help:

  input source indicator does not

• 2910al - 48G Switch: problem with the VLAN

  Hi all,

  I write a new message because I don't know what is happening on my SW series 2910al - 48G and v1910 - 48G.

  I put on the main core SW VLAN 610 and I put to this VLAN IP addreess 100.110.10.1 24-bit etc and it worked fine until yesterday. I change only PLEASE and I enebale STP - loop protect for ports in the range 1-52. (now I rolback this settings as was before)

  

  STP configuration

  

  Now, every PC that has for a long time what IP range 100.110.10.1 24-bit works fine, but new PC have problem with to get the new IP address. I tested it add a static and same address does not work.

  Introduced in second v1910 SW - 48 G VLAN as below

  I connect this flexible switch this \port SW 2910 - G 48, 46 (Vlan 610 tag) <>- at v1910-48G\ port 50 SW (Vlan 610 tahgged) other ports on this switch I put not marked.

  Configuration file for sw v1910 - 48G looks to below:

  #
  activate default domain system
  #
  LLDP enable

  #
  domain system
  disable the access limit
  Active state
  Disable Idle-cut
  self-service-url disable

  #
  rstp STP mode
  enable STP
  #
  NULL0 interface
  #
  GigabitEthernet1/0/1 interface
  hybrid type port link
  port hybrid vlan tagged 610 620
  untagged port hybrid vlan 1
  #
  interface GigabitEthernet1/0/2
  access port vlan 610
  #
  interface GigabitEthernet1/0/3
  access port vlan 610
  #
  interface GigabitEthernet1/0/4
  access port vlan 610
  #
  interface GigabitEthernet1/0/5
  access port vlan 610
  #
  interface GigabitEthernet1/0/6
  access port vlan 610
  #
  interface GigabitEthernet1/0/7
  access port vlan 610
  #
  interface GigabitEthernet1/0/8
  access port vlan 610
  #
  interface GigabitEthernet1/0/9
  access port vlan 610
  #
  interface GigabitEthernet1/0/10
  access port vlan 610
  #

  #
  interface GigabitEthernet1/0/49
  hybrid type port link
  port hybrid vlan tagged 610 620
  port hybrid vlan 1 10 untagged
  #
  interface GigabitEthernet1/0/50
  hybrid type port link
  port hybrid vlan tagged 610 620
  port hybrid vlan 1 10 untagged
  #
  interface GigabitEthernet1/0/51
  hybrid type port link
  port hybrid vlan tagged 610 620
  untagged port hybrid vlan 1
  #
  interface GigabitEthernet1/0/52
  hybrid type port link
  port hybrid vlan tagged 610 620
  untagged port hybrid vlan 1

  etc...

  Could you help me when I made a mistake?

  THX

  The problem was that solve this problem.

  I have blocked all ports. It was a problem. I change several settings and everything works well.

• Equium A100-027 - switch problem ON / OFF wireless

  Hi all

  This problem has been irritates me for some time...

  I've literally just installed MCE 2005 after removing the Vista OS and I ve installed all drivers except for the purposes of ConfigFree.
  I noticed that the switch to turn on/off my wireless card now does not, because it allows me to scan/connect to networks, even when it is in the off position, with the led does not illuminate.

  When I ran before ConfigFree, I noticed that switch was correct entry in the application, but I still couldn't windows to disable the wireless adapter once I turned off.

  I played around with shortcut keys and I ve you press FN + F8 (the symbol wireless) and I've made countless times, but have had no result.
  If anyone knows what is the problem?

  Thank you very much

  Matt

  Great info!

  I noticed that most of the WiFi problems can be solved by upgrading the WLan driver.

  Thanks again for this useful detail!

• Router C4780 wireless network belkin problem

  I have a C4780 which worked well for several years with at least 2 previous routers. I have a Belkin AC1800DB have changed recently and now unable to connect to the router (laptops are connected wirelessly to Belkin WPA2 network without problem).

  When I run a network of C4780 test report it says local networks are detected (including Belkin WPA2) but shoes FAIL against network name SSID found. Similarly the wireless Assistant from the installation disc, the list of available SSIDS for the connection is empty. C4780 both Belkin have WPS, but this does not work in mode button or Pin.

  Because the problem is to find the SSID for all networks I do not think that his associate Belkin (just strange that the problem occurs at the moment I change the router).  But as the C4780 connected perfectly to my previous router, that I do not understand why I now this problem of wireless network connection.

  Any advice much appreciated.

  Try this.   Configure the router to a wireless channel fixed as 1, 6 or 11, never 'auto '.   'Mixed' mode, try now.

• HP pavilion dm4: removing the battery / output switch problem

  MY hp dm4 Clubhouse has a switch relese battery does not move and so I can't remove the battery.

  What can I do to take out the battery?

  I was able to remove my battery, even if the trigger will not move

  I have read the documents under the next heading

  "Laptop battery seems to be stuck.

  He pointed out that my problem was very common

  BATTERY REMOVAL PROCEDURE

  As suggested-

  I inserted a piece of thin stiff plastic

  (for example on the size of a credit card but a little thinner)

  in the crack between the battery and the output switch

  I pushed the upper part of the plastic down

  and then I pushed up in the direction of the battery

  up until the crack of batttery widened to the point where I could use

  my nails in the battery of crack to pull the battery.

  I don't have to much force to make

  The angled battery to easily

  BATTERY INSERTION PROCEDURE

  As suggested-

  To avoid the problem of gel battery switch

  Move the latch of the battery in the middle of its sliding range

  When reinserting the battery first tilting the battery

  so that the side of the battery to the side of the computer case

  is first inserted into the battery compartment

  Then push down the other side of the battery in its compartment

  in the end, release the battery button while he spingngs to its normal resting position.

  I hope that this explanation is useful

• FiOS router m1424wr wireless broadband, having problems to set up

  I just got a used frontier fios model # m1424 wr wireless router.i broadband went to set up after download manual and everything was happening along gently until I tried my roku wireless to the router in place hang, I kept getting errors that my coaxial cable is not connected or broken , I said fine and went ahead and plugged an Ethernet cable for the router.again I got error this coaxial cable not was not connected.i was informed by the operating instructions I should or the other of these connectors plug into the socket that the telephone company had provided in the wall.i can not get my Ethernet wan or coax wan light to come on the download speed of 1 router.i GET g but unable to connect to him because the internet only I get is through a wireless adapter not the wall.i go to 192.168.1.1 it says router status STOP check your connection.it broadband also said I have 3 items connected by Ethernet (2 are active) and 4 by wireless, none of whom was followed active.i instructions very carefully and I can not understand.my first it is You can get anything from the coaxial connection and Ethernet, the phone company installed in everybodys Home.la 2nd question is how can I connect my roku to router when I can't get hooked using Ethernet or coaxial.need

  Hi James,

  Thanks for posting your query on the Microsoft Community.

  According to the description of the problem you are facing problem to implement a router broadband wireless. I suggest you to return the article mentioned below and see if it helps you to configure the router.

  Set up a wireless router

  Yes, if the router has the available slot so we can connect our computer to the router with Ethernet cable. If you are unable to connect Roku with Ethernet cable, I suggest you to contact your service provider and see what they suggest.

  Keep us.

  Kind regards

• FI6248 FC connectivity with MDS SAN switches problem

  Hello

  We have two FI6248 in a cluster must be connected to two MDS SAN switches, using FC ports.

  However, I am not able to configure the ports on the FI.

  There is no "Set up as FC storage Port" option. I don't see what "configure as FCoE storage Port."

  I have the FC SFP (DS-SFP-FC8G - SW--> 8 Gbps Fibre Channel SW SFP +, LC) installed on the two FI6248 on the first 16 ports.

  No idea what is the problem?

  Kind regards

  The 6248UP unified ports.  The ports can be configured as Ethernet Ports or FC ports.  By default, all ports are of type Ethernet.  The ports that you configure is currently an Ethernet port.  You need config of the ports as FC ports.  Ethernet ports will be on the left side of your FI and FC ports will be on the right side.

  The following link explains how to convert a port UP Ethernet CF.  Since it's on your FI and not a plug-in, you have to restart the FI in last step.

  Configuration of the Port Modes for a fabric interconnect 6248

  http://www.Cisco.com/en/us/docs/unified_computing/UCS/SW/GUI/config/Guide/2.0/b_UCSM_GUI_Configuration_Guide_2_0_chapter_0101.html#task_3161F8BE44DA49F6BA9068A5D7594A6C

  Thank you

  Responsible Dan

  Need help with implementation?

  http://www.Cisco.com/go/pdihelpdesk

• No "ip Routing" command on the switch and still intervlan routing.

  Hello

  In my companies 4500 switch I see there is intervlan routing configured for 4 VLANS there but I don't see any command "ip Routing" on this subject

  to enable routing on the switch. A switch can route the same if the command is not there?

  Ninja,

  Default configuration options often do not appear in "show run".  Please try «performance see all»

  Kind regards

  Christopher

  PS your switch and device business, not small business.

• Can I use a router downstream of a switch

  I have a connection internet optical fiber that does not require a modem.  I have a server in my home office LAN Win Server 2008 R2 - for access by remote clients - RDS and 5 computers.  Computers Server and 2 have gigabit network ports, the other maps of 100 MB.  I also have a static IP address from my ISP for my server to be visible to the internet.

  Because my gigabit router is dead, I currently have an old 100 router MB Wireless with 4-port Ethernet 100 Mb, which feeds my switch gigabit (unmanaged), but this causes the switch to be reduced to 100 MB.  To avoid buying a router again, a bit expensive, gigabit, I would like to know if it is possible to have my switch FRONT of the router, so that my gigabit computers can operate at full speed and 100 MB computers can be connected to the router.

  I tried just their hanging in this way, but nothing has worked, but I don't know if I missed something.

  Assuming that you have an external IP only, which will not work. The router must be online before computers.  It is the router that allows a single WAN address to be shared among multiple computers.

• call of CUCM to the router voice FXS thanks CUBE problem

  Hello

  We had a problem in our test environment:

  - - - - Analog telephone

  When we on the g711 codec, both directions of appeal are ok.

  When we put the codec for g729r8, appeal from analog to IP has no problem. But for reverse, the analog phone can ring but will be disconnected after a few seconds. Before the call is disconnected, we find that the codec is "pre-ietf g729" using the command 'show call active voice brief' on the CUBE.

  The configuration of the CUBE and Router (FXS) voice is attached. Really appreciate your advice.

  Thank you!

  Eric

  It seems that the analog phone only supports pre - itf g729 format...

  Unfortunately this codec format is no longer supported on any ios...

  http://www.Cisco.com/c/en/us/support/docs/voice/h323/14069-codec-complexity.html#pre_ietf

  You can try your luck and see if this pre - itf is available on ios, but I doubt it. You will need to have them on all your dial peers.

   maui-vgw-01(config)#dial-peer voice 100 voip maui-vgw-01(config-dial-peer)#codec g729r8 pre-ietf 

  The pre-ietf in this command option is not supported in Cisco IOS release 12.2 and later.