Router WRT54G (ping IP)

Similar Questions

• Cannot access the configuration of my router (wrt54g) page

  I can't access the page of my router (wrt54g) configuration after the installation. The router works fine, but whenever I try to connect to 192.168.1.1 it says the password is incorrect. The first time that I put up I changed the default user name and password and I thought I'd simply forgotten, so I reset the device. This time I don't change any of the default values, and I can not even log on. I have to reset it several times, and you're just annoying. Anyone know how to prevent it from happening? I thought it might be a firmware issue, but I can not find all downloads for my version of road ' rs (V8). I use a macbook pro, osx 10.9.2.

  My neighbor has pretty much the same question. Did some research and found many people with similar problems. Probably time for a new...

• How to install the WPA2-aes security on old router Wrt54G ver 6

  I need help mode WPA2 on my router, I got this router WRT54G ver 6 for several years and it works perfect only thing is that I have no security my nwireless can help them a whole? would be ppreciate it. Thank you

  Your router has the option for WPA2 Personal. You need to access the router interface so that you can select this type of security.

  Please click the link below and it will give you steps how to configure security wireless with your router:

  Title: setting up wireless security WEP, WPA or WPA2 on a Linksys ID of Article wireless router: 19073

  http://www6.nohold.NET/Cisco2/UKP.aspx?pid=80&VW=1&articleid=19073

• Setting up Port Forwarding on router WRT54G, working with a WVC54GCA Wireless CAmers

  I have the equipment in question and you need to know a few things when it come to put in place for Internet access. Before I aske the question, however, I have the following IP addresses associated with this project: WVC54GCA - 192.168.2.102, router WRT54G - 192.168.2.1, the questions are:

  1. How do you define Port Forwarding on every element.
  2. Should the two articles have static IP addresses.
  3. Once the port forwarding is set, what is the structure of the URL to access the camera?

  Any help would be appreciated, summer tear my hair on it. Seems simple, but obviously not. I'm missing something.

  Thank you

  For port forwarding, you will first need to set the camera to a fixed LAN IP address (static).

  If your router uses the range of 192.168.2.100 thanks 192.168.2.149 DHCP servers, then 192.168.2.102 is an unauthorised fixed address.  With the Linksys routers, any fixed LAN IP address must be outside the range of the DHCP server.

  Here are the rules of use of the fixed LAN IP addresses with Linksys routers.  (Note: these rules were written for the 192.168.1.x subnet.)  Since you're using the 192.168.2.x subnet, change all addresses accordingly):

  With Linksys, routers, a fixed (static) IP LAN addresses must be assigned in the device that uses the address. If you need to enter the fixed address to the computer, printer or camera, not in the router.

  When you use a Linksys router, any fixed LAN IP address must be outside the DHCP server rank (typically 192.168.1.100 thru 192.168.1.149), and may not end with 0, 1 and 255.

  That's why any fixed LAN IP address would normally be of the order of
  192.168.1.2 thru 192.168.1.99 or
  192.168.1.150 thru 192.168.1.254
  assuming that you always use the default DHCP server line.

  In addition, in the computer, when you configure a static LAN IP address, you need to set the "Subnet mask" 255.255.255.0 and the 'default gateway' on 192.168.1.1 and "DNS server" to 192.168.1.1.  Note that some network devices can not use server proxy DNS at 192.168.1.1.  In this case, the value "DNS server" your real address of Internet DNS server (found in the router when connected to the Internet).

  It is also important that the same value static LAN IP address no two devices on your network.

  **********************

  After you gave your camera at a fixed LAN IP address, then go in "Port Redirection" in the router and configuring the ports one (or more) to the address LAN IP fixed camera.

  In order to access your camera from the Internet, you will need to either:

  (1) get a fixed Internet IP address (static) address from your ISP and configure your router to use this address, or

  (2) use a free service such as DDNS.  DDNS allows you to use a dynamic Internet IP address, but can connect you by using the same URL.

  I hope this helps.

• How to put in as a bridge wired by another router WRT54G

  I now have a provided verizon wireless router and want to use my wrt54G as a cable bridge.  Basically I want to use the WRT54G as a switch for connecting 3 elements that do not have a wireless (an A / V receiver, XBOX 360 and some storage networking).  The race is too long to have 3 connections directly to the verizon router, so I ran an and want the WRT54G to act as a hub of sorts.

  I plugged the release LAN of my router verizon at the entrance of the WRT54G, but no internet on the wired WRT54G no outputs.  I guess I need something to "bridge mode", but can not understand it.  I suspect also that I need to disable DHCP, assign a static IP address, and probably more, but I don't have a chance.

  Any ideas?   Help is greatly appreciated.

  What is the ip address of your router verizon?

  Make sure that the ip address of the router Verizon and both are the ip address of the router Linksys assume to be in the same network range. (E.g. Verizon router ip - 192.168.2.1, Linksys router ip - 192.168.2.2). Then connect the router verizon Ethernet cable to linksys router in the number in Port 1. Open the page of the Linksys router setup disable DHCP and wireless (as you say you want to 'use as a wired router wrt54G')

• How to connect a second router WRT54G

  I can't get a signal through my entire House so I bought a second router WRT54G, running that the Setup disk affects only the first router so how do the other work?

  To connect two routers together, go here.

• Router WRT54G wireless does not work with the new modem

  Hi, I use my router WRT54G (Firmware version v2.02.7) on 4 computers for more than four years now, without any problems at all. However, today I had to replace my old modem with a brand new modem Speedtouch from my supplier, and although I made sure each cable has been connected properly, it just doesn't.

  The connection between my PC and the router (http://192.168.1.1) is good, but the problem must be between the router and the new modem. When I click on 'Status', he said: ""connection status: disconnected".

  After clicking on the 'Connect' button, it tells me that it "can not connect to the PPTP serverbe"

  Help, please

  Hi Matt,

  Although the resolution of this problem was a little simpler, I still thank you for your answer.

  The neighbor boy came up with the following response:

  «It just check the Type of Internet connection, cause you got an old type of modem before.» It will probably be set to PPTP. If this is the case, simply change it to "Automatic DHCP Configuration", click on "Save Settings" and everything should be ok then"

  And he was right!

  I am so happy

  BR,

  Niqui

• Router WRT54GS WET54G bridge question, the bridge to connect to a wired router?

  Hi all

  I have a wireless - g LAN using a WRT54GS router.  The existing wireless devices on the local network are 2 PCs, a TiVo unit (using the TiVo wireless adapter) and 2 WET54G Wireless bridges.  A bridge connects ethernet wired to a network printer.  The other bridge connects by ethernet cable to a reader Blu - Ray Sony BDP-S550.

  Security is WPA2-AES.  so far this works well, believe it or not, but I grew a lot older, making it happen.

  Now, here's what I would do: I would like to add another device LAN cable where the second bridge WET54G connects to the Blu - Ray player.  The bridge has only an ethernet cable connection, so I have to find another way to get the two devices connected to the wireless LAN.

  I have two other devices LinkSys, kicking around here that I can use.  One is a BEFSR41 wired router.  The other is a WAP54G Wireless Access Point.   If I can use one or two of those who in some way, I won't have to buy another camera.  It is the order of the day so far.

  Right now it looks like this:

  Router WRT54GS wireless wire WET54G bridge entry WAN router BEFSR41 son to two LAN devices.

  I have problems performing this work, assuming that it can still be done.  Can I get this config to work, or what I need to add the Access Point where the bridge is now, or...?

  Thanks for your time,

  Big Al Mintaka

  You already have a network working with your existing devices. What you're trying to include in your network is possible and can be done. Rather than plug the cable of the WET54G to the WAN port on the router, connect the cable to the router's LAN port. Disable DHCP and change the LAN ip address in the range of your existing network. It should work.

• WRT54G Router by ping how-to Internet port.

  Hello world

  I have a small question for you. My LAN has a main router that is configured on the linux system. And I have 2 WRT54G routers which should be the wireless access point. First question is therefore:

  Is it possible to set up the routers on the Access Point mode? I have not found this option anywhere...

  Second question is-> when I connected my LAN via the Internet port that I can't ping routers WRT... when I try to ping the routers I just received 100% packet loss. How do I put this activate port ping, because I would like to set up the routers via another VLAN.

  Now I connect this routers via the switch port, and there the work but I want to use internet port-> appropriate in my opinion.

  Thank you for any help

  1. to use a WRT as simple access point, set it to a free LAN IP address inside your existing LAN subnet and disable the DHCP server. Then, plug the WRT via a LAN port number to your existing network. Do not use the internet port on the WRT.

  2. If you connect your WRT via the internet port (not recommended for your configuration), you must disable the "anonymous block ICMP" or similar in the Security page of the router. If you want to configure the WRT via the internet port, you need to enable remote management.

  3. I always highly recommend to connect the WRT via a LAN port, as in no. 1. It's much better. Only, you have a single subnet LAN and no cascade of routing. Also, all computers can access each other. See also here.

• As a router WRT54GS cascading with IP fixed address block

  Hello

  I read several threads on the routers in cascade and the Knowledge Base, but none seems to fix my script with a router with fixed IP address block.

  My current setup is an ADSL circuit with a block of 8 fixed IP addresses. Of them the first xx.xx.xx.137 is assigned to interface the router, the second xx.xx.xx.138 for the router itself WAN xx.xx.xx.139/140/141/142/143 leaving as usable IP addresses. Connected to the ADSL circuit is that a D-Link DSL-G604T router with NAT disabled to allow IP addresses to be assigned to my web servers and ftp. Of course, DHCP is disabled on the LAN interface.

  Unfortunately, the transmitter wireless on this router is defective so I would my Linksys WRT54GS (Firmware v1.50.6) D-Link router cascade so that I can use it (with active DHCP) as a point of access for multiple wireless devices.

  This thought through to logically I've named WAN 54GS with one of the xx.xx.xx.140 to static IP address available, a subnet mask 255.255.255.248 and the door entry xx.xx.xx.138. I left the LAN settings like the beach 192.168.1.xxx and DHCP active. I then connected the interface WAN of the 54GS to one of the LAN connections on the D-Link with a straight ethernet cable.

  I can connect to the admin 54GS via a direct ethernet connection and wireless interface but not to the internet.

  I can ping that is the xx.xx.xx.140 of the interface wan of the 54GS since a laptop computer connected wireless but not the IP address of the gateway of the network xx.xx.xx.138. D-Link router.

  Am I missing some other settings in the router. Especially in the routing section advanced? I guess that the device must be set to a router rather than the bridge, but if there are parameters of dynamic routing?

  Any help would be appreciated

  Thanks Brickmonkey,

  Just thought I would update this post. I tried from you suggestions, but to no avail. The frustration I did a hard reset of the router D-Link and set it up again from scratch and... Hey presto it now works.

  I can only think that there may have been some settings left from when the router has been initially implemented for Nat and I had configured port forwarding. In any case it now works OK then thank you very much for your answer.

  Fozzie

• Connection with a switch EZXS55W or a second router WRT54G to my router network WTR300N home?

  I have a home office in my basement with my computer connected to a lan of my WRT300N router that is set up on the first floor and networking with three additional computers to the floor as well. I want to add 2 additional computers in my basement and wireless is not a good set upward because the signal strength is very low. I have great reception on the floor and even on the second floor where my children are connected from their rooms. My question is: I have an older WRT54G Router I use is more and want to know if I can connect it to my WRT300N using the lan line ran down in the basement which is connected to one of the Ethernet ports of the WRT300N? If so, how the connection and set up the second router? Also, I can use Ethernet cables to connect my three computers to the second router or what I need to use the wireless of the second router? I was looking at the switch EZXS55W at the Wal-Mart local and thought that was my answer, but after a search through all the answers of the basis of knowledge here, I'm confused on the approach to take and which one would be the best game for me. Here, any help would be great!

  With the EZX you extended your wired LAN. You can still use the WRT54G to add another point for other cable ports and wireless access. Just do these 4 steps as stated in my previous post.

  You can connect the WRT54G the WRT300N or the EZX. Basically, it's all the same. You don't have to turn off the switch before you connect a device.

  If you want to use the additional wireless WRT54G, you can try to set up a roaming wireless network. Implement the WRT with identical settings as on the WRT300N wireless, i.e. identical SSID and wireless security the same (preferably WPA2) personal with a good password. Do not turn off the SSID broadcast on either WRT. Only the allocation of channels should be different at a time to avoid any interference. Now the devices should be able to move from one access point to another without losing the network connection.

  However, if you perform this configuration test carefully. I don't know how it works if you have a N Router and a G. If this does not work, use different SSID on both. You can then choose which SSID to connect to on the client.

• Router WRT54G wireless

  How do I connect three WRT54G Router on three floors so I can connect all computers to my internet modem

  Move the ethernet cables. The Wrds requires a wired connection to the internet. They don't connect wireless to other routers. The exact configuration depends on whether you have an internet modem or in fact a router with built-in internet modem.

• Disable the connection to Emule, BitTorrent... router WRT54G

  Hello

  I have a WRT54G and I would like to disable connect to Emule, BitTorrent and other software you can download illegally on this subject. How can I do?

  Thank you

  Ishmael

  PS: Sorry for my English

  I don't think that there is no adjustment or the Protocol on the router that would block the torrents or illegal downloads also. You can only block specific Web sites by blocking the site based on the URL. I'm sorry.

• Configuration wireless router WRT54G without CD - problems with manual installation

  Hello.  I have a WRT54G Router that I've used over the years, because my former cable provider provided me with the router.  I recently switched to cable operators & they do not provide a wireless routers.  I would use my WRT54G Router, but I don't have the cd.  I thought that it wasn't a problem because I can just do a manual installation using the 192.168.1.1 ip address.  I get the pop up window to enter user name & password.  I followed the instructions & just type in the word admin password field & l left the user name empty, but it does not work.  Can someone please?  I know that I can solve this problem.  It is not sensible to spend money for another router when this can be a simple solution.  Thanks in advance for your help.

  Press and hold the reset on the back for 30 seconds and then release.  Wait 10 seconds and power cycle.  Now, try again.

• Configuration with a new router WRT54G

  Hello, friends.

  I have a Linksys WRT54g router which works fine, but the signal is not very good on some points of the House.

  So I bought a TP-Link 740n to use as a second router. My idea is to connect two routers with a 10 meters lan cable I have, to improve the signal on the points that are remote from the main router (Linksys) or separated by walls.

  How can I configure two routers to do the job?

  When the job is done, I see two different (one for each router) networks on my laptop or the 'original' signal (WRT54g)?

  I would be grateful if someone could help me. I know almost nothing about the configuration of routers.

  Thanks in advance.

  GALAXY2013 wrote:

  Hello, friends.

  I have a Linksys WRT54g router which works fine, but the signal is not very good on some points of the House.

  So I bought a TP-Link 740n to use as a second router. My idea is to connect two routers with a 10 meters lan cable I have, to improve the signal on the points that are remote from the main router (Linksys) or separated by walls.

  How can I configure two routers to do the job?

  When the job is done, I see two different (one for each router) networks on my laptop or the 'original' signal (WRT54g)?

  I would be grateful if someone could help me. I know almost nothing about the configuration of routers.

  Thanks in advance.

  Or you can access the link below as a guide.

  http://www6.nohold.NET/Cisco2/UKP.aspx?VW=1&docid=529c188bc0ee4f7da79ffc22f2be33ec_4579.XML&PID=80&r...