Routing to the unauthorized via switch Ethernet HP 1910 169.254.0.0/16 subnet

Similar Questions

• I cannot connect to the Internet via an Ethernet cable but I am able to connect with other devices.

  Original title: deleted Ethernet adapter

  Hello

  All trying to fix my computer run Registry cleaners, I managed to delete my Ethernet adapter, I have taken steps to try to fix this problem and have been advice to visit Microsoft support for help.
  I have a Dell Dimension 5100 and am running Windows XP, I am unable to connect to the Internet via an Ethernet cable but I am able to connect with other devices.
  First of all, I contacted my Internet provider which forced me to various checks to see why I was getting a message saying acquiring network address and it seemed that I had no IP address and could not connect. He eventually get look in the network adapters Device Manager, he demonstrated Intel PRO/100 VE network connection that is activated in the State shows that it works, but there is no Ethernet adapter shown in this place.
  I tried to insert Dell drivers and utilities disk, but that does not change.
  I tried to download on an other computer files from dell that look like they are pilots.
  I tried to set up a new connection
  None of what I tried so far seems to have worked, can anyone suggest what I can do to fix this?
  Thank you
  Kevin

  Hello

  1. what you're trying to fix by running registry cleaners?
  2. How did you remove Ethernet card?
  3. How are you online using other devices?
  4. What are the devices are?

  Intel PRO/100 VE network connection is the Ethernet adapter on your computer. The following articles may be useful:
  How to troubleshoot possible causes of Internet connection problems in Windows XP
  http://support.Microsoft.com/kb/314095
  Windows wireless and wired network connection problems
  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

• How can I connect a cisco router to the internet via a cable modem / router gateway

  I have searched here but can't find the exact answer that I'm looking. I have a switch and a router cisco 1760 2950. The router has an added ethernet wic card so I have two ethernet connections available. I would like to connect the cable modem gateway the router through one of the connections on the router, then the switch ethernet. I can't get this configuration to work. There are several different ways, I saw displayed to accomlish. DHCP, without dhcp, creating a separate network and giving the e0/0 cable an ip address in the range of addresses network gateways. None of this has worked. Can someone after the commands that must be entered on the router to make this possible?

  Hello, I'm assuming that your ISP is to give addresses via DHCP...

  And I suppose also we want to implement our router DHCP in our local network to give our PCs and laptops etc...

  So what we need to do is:

  conf t

  !

  interface e0/0

  Description # INTERNET #.

  IP access-group MY_WAN in

  DHCP IP address

  NAT outside IP

  No tap

  !

  interface e0/1

  # MY LAN description #.

  IP 192.168.1.1 255.255.255.0

  IP nat inside

  !

  IP access-list standard MY_LAN

  permit 192.168.1.0 0.0.0.255

  !

  MY_WAN extended IP access list

  allow tcp any a Workbench

  refuse TCP a whole

  allow an ip

  !

  IP nat inside source list MY_LAN interface e0/0 overload

  !

  IP dhcp excluded-address 192.168.1.0 192.168.1.99

  !

  dhcp MY_LAN IP pool

  network 192.168.1.0 255.255.255.0

  default router 192.168.1.1

  Server DNS 8.8.4.4 8.8.8.8

  In this configuration, I applied an ACL for a protection to my router and my network to allow only established connections that Ive from my LAN to return to me. Anyone who tries to open a connection to your router will be refused. Everything is allowed. But you can change this option to be more specific rather than wide.

  On your switch, if you leave all ports in the vlan 1 and have as access ports, it should work.

  Hope this helps

  Please note the useful messages and don't forget to mark resolved all questions answers. Thank you.

• Satellite A80: Failure to connect to the internet via an ethernet cable

  I'm having problems to get an internet connection via a cable ethernet to my office. The laptop works everywhere else, but not in the office. The strangest thing is that my desktop at the office computer works perfectly with the same cable.

  The icon in the taskbar of configfree reads "MARVELL YUKON 88E8036 PC... 169.254.95.8"no matter how many times I disconnect and reconnect it to my office. Curiously, the IP Office when it is connected to the same cable is 192.168.1.69.

  I was told to change the tcp/ip properties manually, but I'm not able to do because I have not all entries in the NETWORK CONNECTIONS or can't seem to create a new.

  I would be grateful if anyone has any suggestions.

  Hello

  I wonder why you have no entries for network connections.
  Click Start-> settings-> network connections-> connections to the Local network-> properties

  Select the Internet Protocol (TCP/IP), and then click Properties.
  If you use a server in your office and the IP address is assigned automatically then all TCP/IP parameters must be on automatically

  Check it!

• Canning Internet connection drops when the computer is connected to the PS3 via an Ethernet cable.

  Original title: Shared network problem

  I am trying to use a shared network, configure as follows. My computer connect wireless to my router. My PS3, however, seems to be really slow when connecting wireless to the router and is at a proper speed when connected via ethernet. So, I have my PS3 connected to my computer with an ethernet cable. I put the wifi connection to be shared. Next, I set up my PS3 to connect to cable internet. Has gone through the steps and connected properly and at full speed too. However, there is a problem. My PC guard 'give up' connection to my router, while remaining connected to the PS3. I have to manually connect to my router again, regardless of the connection automatically option. Almost as if my PC is to use ethernet for internet access, (which he won't get that which is connected to the PS3) and so it loses the wifi connection. This abandonment happens around every 5 minutes or more.

  Is it possible to keep my PC connected to my wireless router and still be connected to my PS3 through ethernet to connect my PS3 using my PC?

  The problem seems to have 'fixed itself. I tried messing around with the connections that would not work even the bridge. Then I've switched back to ICS and did not have a disconnect since then.

  So the problem is now resolved, but don't know how?
  Whatever it is, I am very grateful for your help Manasa, it is well appreciated!

• Connection from the desktop (Vista) to the WRTP54G via an Ethernet cable

  I replaced my old XP desktop with new Dell XPS One with Vista. The old office was connected to my router (WRTP54G - Firmware Version: 5.01.04) via Ethernet cable and worked like a charm. A new won't recognize this connection - is seen as "unidentified network" with "access: Local only". The wireless connection on the same office works, but I still don't understand why I can't it be connected via cable. My XP laptop is not yet had problems with this Ethernet connection to the router - it recognizes immediately as the connection to the local network and connects to the Internet.

  I suspect there is a problem with the WRTP54G in the Vista environment, because the Ethernet connection started work immediately after I have had bypassed the router and connected the office directly to the cable modem.

  Any help to fix this problem will be greatly appreciated.

  Give the 192.168.15.5 static IP address and the default gateway 192.168.15.1.

  Click on the Start button > Control Panel > Network and Sharing Center - slot, click 'Manage a network connection' - task do a right-click on the connection icon to the Local network and click Properties-on the 'Général' tab, select ' Internet Protocol Version 4 TCP/IPv4 ' and click on the button properties-select "Use the following IP address" - provide the IP - 192.168.15.5, subnet mask - 255.255.255.0 Default Gateway - 192.168.15.1 - favorite DNS 192.168.15.1, auxiliary DNS - 4.2.2.2 > click the Ok button to save and click 'Close' on the main properties window.

• Can not connect Equium M70 to the Internet via an Ethernet cable

  I have recently install wide telewest broadband via the installation disc. I used the provided ethernet cable. During installation, I received an error message stating that it could not connect due to various problems.
  After a long discussion with the customer service and try several solutions over the phone we wouldn't always get connection using the ethernet cable.
  Telewest has also provided a USB cable so I was told to remove the ethernet connection and plug in the USB. The connection has been made instantly.

  Has been informed by the technical support of Telewest, that I had a problem ethernet on the laptop. This could be correct, or maybe it was an ethernet cable from the spleen.
  Any suggestions? My laptop is only four months.

  Hello

  It is not easy to believe that the network adapter does not work on your laptop. What is the status of LAN in Device Manager? When the cable is connected is the assets of orange or green led or not? Try also to start ConfigFree tool. Under the physician connectivity tab, you can see their actual situation and if there is a problem of communication it will be shown here.

  If there is any attempt of trying to test it on another network (perhaps in your company).
  You can also contact your dealer and allow it to check the device. It can be done in the store and may not take a lot of time.

• Windows 2000 is the network via an ethernet connection does not work.

  Windows 2000... CHANGED DIAL UPWARD... FOR ETHERNET
  I just installed a Lan card so I can connect an Ethernet cable to the router, as I had the OLD DIAL-UP CONNECTION to A TELEPHONE LINE...
  but I am unable to connect to the Internet... I checked my device manager and it say's works well... I asked my Internet provider for help on the connection, BUT ILS DO NOT SUPPORT MY WINDOWS VERSION
  Can someone please advise

  Hello

  I suggest you to download and install the drivers for the network card and check if it helps.

  You can try to get the drivers, go to the manufacturer's Web site and check the version of the windows 2000 drivers.

• Ezvpn client unable to route to the Internet via UC540

  Hello

  I have a UC540 configured as a server Ezvpn. I can connect to a Cisco VPN client and connect all private addresses, register the IP communicator etc. However when I try to connect to the web using a web browser it does not connect.

  The client receives the server's DNS entries. I also tried to use the IP address instead of the DNS name and still able to connect on the Internet only. It is a complete tunnel split. I tried checking the box in the VPN client to make a tunnel of split and still unable to connect. Guests on the main site (directly connected to the UC540) can connect to the Internet fine, it's just through the Ezvpn, they can't.  The subnet Ezvpn is included in the nat ACL.

  Any advice would be appreciated.

  Andy

  Andy,

  What is the legacy or the deployment DVTI?

  If inherited, you can create a fake loopback (with 'ip nat inside') and punt ezvpn subnet to it with a road map.

  If DVTI can you please make sure you have 'ip nat inside' on the interface?

  Running config would help ;-)

  Marcin

• orangle flashing light on netgear wireless router, but have internet via a modem... Please help

  I am connected to the internet via an ethernet cable via the modem I have, but the netgear wireless router that I have demonstrated a blinking orange Internet when I try to connect wirelessly, I tried to reset the router and the modem and had no luck, I also tried to penetrate in the maintenance of netgear online but who also won't allow me to enter. Finally I tried to release and renew my through the cmd ipconfig and shows an error message saying that the media is disconnected... Please help me

  Hello

  I suggest you to post the same question in the NetGear forums for support on the NetGear router and check if it helps.

  http://forum1.NETGEAR.com/

• Connect the WRV210 router to the Internet

  I'm trying to connect a new Cisco WRV210 router to the Internet via a D-Link (yes I know - you have to work with what you have) Ethernet Modem ADSL2 + DSL-320 b and can't seem to get a connection. All ideas welcome.

  Thank you

  should be in the SCOPE of the looks of the manual networking

  FTP://FTP.Dlink.co.UK/dsl_routers_modems/DSL-320b/DSL-320b_manual.PDF

  Section 3 page mode Bridged 24

• Connection to the meter via LAN without VISA library

  I connect my HP33410A via a LAN cable to my PC using the VISA library. I'll send SCPI commands and everything works OK.

  But my application must also connect without a VISA and for me it's a big problem. I read some information, I have to use the SOCKET connection with the TCP feature.

  Is there a simple way to do this? I was punctuating certain functions in LabWindows supporting TCP protocols and socket. SDK library also support the SOCKET connection, but for me it's black magic

  Could someone post here a code to query a simple as command "* IDN?" in this interface LAN without a VISA?

  I would be grateful

  (Sorry for my English I hope you could understand the problem, I describe )

  I solved the problem. It is more simple than I thought you just have to connect to the TCP server. Earlier, I tried to do that, but with the incorrect port number. I think that for most of the devices Agilent TCP port number is 5025 (I've read that in manual for SOCKET connection)

  I stayed here a piece of code that shows how to establish a connection with the agilent device:

  ConnectToTCPServer (& tcpHandle, 5025, '169.254.4.10', TCP_Handlig_Function, 0, 0);
  ClientTCPWrite (tcpHandle, "* IDN?", 5, 0);

  ClientTCPRead (tcpHandle, buff, 50, 0);

  And that's all you need to do. Is not as simple as that?

• Airport extreme for modem cable via an ethernet switch?

  I can connect the airport extreme to the modem cable via an ethernet switch, or must the extreme connect directly to the modem?

  The answer to your question depends on what type of "modem" cable you may have.

  If you have a simple modem, as in the example below with a single port Ethernet, your network should look like this:

  Internet > Modem > AirPort Extreme > Switch and other devices.

  

  If you have a modem/router, which is actually a modem and a router separate which are combined in a single package, looking for something like the example below, your network may look like this:

  Internet > Modem/Router > switch > AirPort Extreme and other devices

  or... it might look like this:

  Internet > Modem/Router > AirPort Extreme > switch and other devices

  

  If you do not know what kind of modem you have, post back with the number of brand and model of the device that you call your "modem", and we will do some checking.

• cRIO only with switch ethernet connection and the computer

  Hello

  I use a cRIO-9073 connected via an ethernet switch and then to my computer and also connected to the corporate network. The cRIO connects fine (I can interact with the remote façade on the cRIO) using this method, but I can't view the remote façade when I connect just my computer for the cRIO via the ethernet switch. Where can I find the method of connection to cRIO by ethernet switch?

  Thank you

  Note: I configured manually my computer an arbitrary IP address and the subnet mask when you use only the ethernet, cRIO combo switch, no network. But I can't repeat the cRIO connection, there may be a step I'm missing.

  bermea,

  Hello! Let me be sure I understand your problem and then make a sugguestion.

  You have your PC and the cRIO connected to an ethernet switch that is also connected to your company network and you are able to see the cRIO to the MAX. However, when you have disconnected your network switch companies, leaving only the PC and the cRIO connected, you are more able to use the cRIO or see in MAX. Is this correct?

  It seems that you have indicated that you have setup your PC to have a static IP address for when it is disconnected from the network. If this is the case, you must also set the cRIO to have a static IP address. Here are some documents that can help you do this.

  • Choose a static IP address for your engine in real time
  • Why my controller cRIO not Show Up in MAX?

• connect hp photosmart 7960 to the network via ethernet

  the hp photosmart 7960 device can be connected to my router via an ethernet cable so I can access it with my touchpad?

  Hello

  Yes we can. Here's a topic on how to implement:

  http://www.LIUtilities.com/how-to/set-up-a-print-server/

  Kind regards.