Running ESX 4.1 ProLiant ML110 G6?

Similar Questions

• Notice of default of table when you run Esx 3.5i on HP Proliant Server

  Hi all.

  I'm sure this must have been invited several times already, but I sent several hours looking and reading and have not found an answer that is even close.

  I have several DL380G5 servers HP integrated VMWare Esx 3.5i.

  I have a stand-alone server running HP SIM 5.3.

  HP SIM detects the ESXi server and the virtual machine, but if I pull a car on one of the table I get no notification of the faliure.

  How you be notified on hardware failures when running ESX 3.5i?

  I enabled SNMP on my ESX 3.5i server according to the documentation, but there is still no info on the table and the failed drive.

  HPSIM reports the following information about the server, which I believe indicates HPSIM is in talks with ESX 3.5i via SNMP

  Type of system	Server
  Subtype of system	HP ProLiant, x 86 system, VMware ESX host, embedded, virtual machine host
  Product model	ProLiant DL380 G5
  Description of the material	ESX1
  OS name	VMware ESX Server 3i 3.5.0 build-153875
  OS type	Hypervisor
  OS version	3.5.0
  Description of the OS	#1 SMP Release build-153875, March 13, 2009 17:29
  Management protocols	WBEM:1.0

  By clicking on the State of health provides information on Fans, memory, power and CPU.

  Do I have to install some sort of agent in ESX 3.5i to report on events from an array P400 controller?

  Thank you very much

  have you seen HP VMware ESXi management environment , it may be of some use.

• Need Driver video for Proliant ml110 G6

  I need hardware drivers - video - chipset, etc and I watched and google anywhere. Not on the Easy Setup CD or the Drivers from HP website. Help?

  System: HP Proliant ml110 G6

  OS: Windows Server 2008 R2 (x 64)

  Hello:

  Here is the link to the Matrox driver page.

  They do not seem to support the MGA G200 card for 64 bit anything.

  http://www.Matrox.com/graphics/en/support/drivers/latest/

  I suggest that you post your question in the Forum of HP Business - section ML servers Support.

  http://h30499.www3.HP.com/T5/ProLiant-servers-ml-DL-SL/BD-p/ITRC-264

  Me?  I woujld just buy a new card capable video of windows 7 and be done with it.

  Best regards

  Paul

• Connect a Powervault MD1200 to a PowerEdge R710 5.1 running esx using SAS cables

  Hello

  I bought a Powervault md1200 and a perc h800 controller.

  I'll install the perc controller in my PowerEdge r710 5.1 running esx server.

  Then connect the md1200 to the r710 via sas cables. The powervault is no NIC.

  My question is, how to configure the RAID while booting the r710? I understand that if I were on Windows, I could use open manage but I'm not familiar with how to do this from a 5.1 esx server.

  I'd appreciate any help.

  Thank you

  Flynn

  Hello Flynn,

  What you need to do is to go into the Bios of your H800 controller and you can then configure your virtual disk MD1200.  Once you have the virtual disk created, then you will be able to do a scan in ESX & he should see the virtual disk that are created.  To access the boot controller bios you need to hit Ctrl + C to enter the bios.

  Please let us know if you have any other questions.

• How to win 2012 Server virtual machine with vmware cluster running ESX 5.1 and ESX 4.0

  Hello

  I had cluster running ESX 4.0 host, I upgrade vcenter 5.1 and added a new host running 5.1

  When I try to create a new virtual machine, it does not give me option to choose win Server 2012.

  I tried to disable fail on etc... but not helped.

  Any thought.

  Thank you

  
  

  Got it, I had to choose the vm hardware version 9

• VMware ESXi does not support the RAID on HP Proliant ML110 G5 drives

  Hello

  I installed VMware ESXi on my HP Proliant ML110 G5. I got 3 hard drives on my server at the moment, one of them is VMware ESXi and other two are RAID1.
  Whenever I connect to my server via vSphere client I have the chance to see every HARD drive (datastore) separately.  Is it possible that VMware does not RAID installation?
  I would need to see these two hard drives as a data store. Do you have any ideas on how I can do?
  Thank you.

  like any other typical server, you need to configure the sata raid controller RAID5/RAID0. but keep in mind that this controller without any battery backed cache would have very horrible performance. Another way is that you can use datastore span to provide as a large store of data, but if you lose all of the computer, you will lose all data.

• Running ESX for free?

  Is it possible to run ESX after the period of assessment without purchasing a license? I thought it was possible to run ESX after the eval for free, but in a more limited fashion. I can't find any mention of this now, so maybe I'm wrong. I know that you can run VMWare Server for free on top of Windows, but I would like to know if it is possible with ESX.

  ESX expires after 60 days.  ESXi, you can get a free serial for and use it indefinitely.

  -Matt

  VCP, vExpert, Unix Geek

• Help networking running ESX (i) in the VM Workstation

  Hi everyone-

  Hope someone can help.

  I have ESX (i) running in the VM Workstation on my laptop. My problem is that I can't move from my laptop to the domestic VMs. The route correctly on VMs inside and I can communicate back and forth with ESX just cannot access the internal VMs from my laptop. I can ping the default gateway of my laptop workstation VM virtual network editor implements.

  -On promiscuous mode

  -Tried several options with nic, vSwitch and VM workstation network Editor.

  Any ideas on how to Setup network for this config? Goal is to be able to RDP to internal VMs.

  Thank you

  Jason

  This should be pretty easy - please show a screenshot of your network virtual Editor settings.

  Here is all I have to do on the ESXi vmnet0 for example ethernet card

  the host can have the IP 10.0.0.1, the ESXi then takes 10.0.0.2 and the nested VM gets 10.0.0.3
  I don't have to manually set routes at all

  It should also work with vmnet0 and DHCP for three - assuming you have a DHCP server that is connected to the bridged the host network adapter

  during troubleshooting, turn off the firewall host and the nested VM

• ProLiant ml110 g5: Server Proliant Ml110 G5

  System does not boot after the power failure.  Turn on and turn off fans.

  Hello:

  You can also ask your question on the Forum of Support Community Business Enterprise HP - ML servers section.

  http://h30499.www3.HP.com/T5/ProLiant-servers-ml-D L-SL/bd-p/itrc-264 #. VemggWaFO9I

• Windows 2008 SP2 running on a HP ProLiant DL160se - cannot delete hiberfil.sys

  First of all, it's a running AD AD 2008 R2 domain controller.

  It was built about 2 years ago.

  C: 30 GB disk

  100 GB drive D:

  Yes. I know that the C: drive is small but that's the way it was built and I have to live with it until the next refresh.

  Here's my problem.

  I'm only 400 MB of free space on the C: drive and am afraid that at the next round of patching this server will run out of space.

  We have a file hiberfil.sys on the C: drive, which is close to 5 GB in size.

  We don't Hibernate enabled nor do we ever want to use.

  I Googled it and I tried all the suggestions and nothing seems to me to delete the file.

  I don't have a HibernateEnabled registry setting anywhere in the registry.

  I don't have a setting of 'Sleep' in the Advanced Power Options.

  I tried the following, and I still couldn't remove:

  -powercfg/h off

  I also tried to enable it, but it came up saying that I don't have enough space to create the hibernation file. WTF?

  As much as I can say that we have no setting Hibernate anywhere in the OS so why this file exist and how can I get rid of him. ?

  Help! at the end of the roll.

  Hello

  Support for Windows Server is not provided in these forums. On the other hand, it please repost your question in the relevant Microsoft TechNet forum here:

  http://social.technet.microsoft.com/Forums/en-us/category/windowsserver .

  Thanks :)

• Known issues with running ESX, vSphere and vCenter Lab Manager on a Windows Server?

  I'm on a project that is currently planned to install ESX, vSphere and vCenter Lab Manager on a Windows 2003 R2 Enterprise x 64.  Anyone know if there are known problems with their performance on a beefy Server?

  http://communities.VMware.com/community/VMTN/vSphere?view=overview and take a look at podcasting.

• Network problem with HP DL 380 running ESX

  Hi @ all,

  I m having a BIG problem with a HP DL 380 and ESX 4.0. The setting is as follows:

  1. physical NIC is on the DMZ Port of the firewall, the 2. one is on the switch (simple gigabit switch).

  one of the virtual machines on this server should communicate ONLY on the NETWORK card on the demilitarized zone, but somehow he doesn´t work.

  help the plt

  Bone

  OS (if it's still bone),

  Setup in your jpg looks ok.

  To dig deeper, I need to understand the issue see you "if I turn on the server 'DMZ' is as if it is on the first vSwitch '

  Can you explain the issue you are facing. Is this a connectivity problem. Maybe it is related to the configuration of the physical switch.

  André

  If you are having trouble to explain in English, feel free to send me a private message and describe the problem in German.

• HP Proliant ML110 G7 graphics driver - Windows Server 2003

  I was wondering af, only at - he got the Matrox G200 WELL to work under Windows Servre 2003?

  I messed around with a few things, but nothing has worked so far.

  Well that's all just amazing what reading list on the for the server installation DVD will do for a fellow. It's right there in front of my nose.

• No physical network is running 5.5 ESX VMware 7

  Dear all,

  I am trying to run ESX Server 5.5 on VMware Workstation 7 and following fervent error, please help...

  Cybermate

  To run ESXi on VMware Workstation 5.5, you need to VMware Workstation version 9 or higher.

  VMware KB: Support for ESXi/ESX implementation as a nested virtualization solution

• Error: Running VMware ESX in a virtual machine requires the external virtual machine

  We are running ESX Vmware 5 on a virtual test in ESX 4.x environment and machine unable to start the virtual machine on Vmware ESX 5. with the following error.

  Error: -.

  Running on a virtual machine VMware ESX requires the external virtual machine is configured to run a VMware ESX guest operating system. You can not power on a virtual machine until the external virtual machine is reconfigured.

  We found after KB

  http://KB.VMware.com/selfservice/microsites/search.do?language=en_US & cmd = displayKC & externalId = 1030283

  Howerver, I'm not able to find the option

  1. Select the virtual machine that is running ESX.
  2. Go in VM > Settings.
  3. Click the Options tab.
  4. Select the General settings.
  5. Under Guest operating system , select VMware ESX.
  6. Click OK.

  We are not able to find this option in ESX 4, so we can run this VM.

  Please help urgently...

  Kind regards

  The log file looks good now.  However, it seems that ESX 4.0 is older than I remembered.  Please, add the following line to your ESX VM configuration file and try again:

  monitor_control.restrict_backdoor = TRUE