RV042 seems to fall packages/traffic

More weird behaviors of the RV042. It seems that he struggles to complete a download from a Web site such as less than half of the websites visited downloads only partially. He has weird symptoms - all the text but no CSS or formatting, images, but not all, or even a mistake "this server is not found." By clicking on a link you will often feel like the request has been sent into a black hole and I often have to click two or three times in order to ensure that there is an action. And is not with small sites with accommodation House; This is behavior I see on MSN.com, Google.com, Amazon.com, etc.. In all cases, refresh several times finally gets the site downloaded, but it happens to be irritating when I perform this ritual for all other Web sites.

Here's what I've tried so far:

-Disabling the firewall

-Disable all firewall options

-Disabling the firewall options one at a time

-Via a different wiring

-L' use of different ports

-With the help of different computers

-Updated to the latest firmware

-Restart

I get similar questions when I navigate using my phone connected to WiFi. I tried 4 browsers (Safari, Firefox, Chrome, IE), all face the same problem.

The only thing I can do to make it go away is to bypass the router altogether. I wonder if anyone has experienced this problem and if if I should worth spending a minute of time on it (like what) POS router. I have had him since August, and it has a date of manufacture of April 2010. It is marked V02.

If asked, I can easily provide examples of screenshot of what is happening. Maps.google.com especially: all the other columns of mosaics will load, but others will remain a Tan solid with 'fact' in the status bar. Seriously frustrating.

Nathan,

You could try for the MTU 1492, even if it looks like you have found that 1500 should work fine. This problem certainly looks like it is the MTU. I think that I would consider updating the firmware (again if you have the latest version), default factory setting and reconfigure the router manually.

Tags: Cisco Support

Similar Questions

Tunnel of RV042 V3 that routes all traffic to the VPN

Hi all

I use Cisco Linksys RV-042 with V2 hardware to set up a VPN tunnel that route all traffic to the remote gateway (a Cisco ASA 5510). This configuration works very well, and I can access the local router and other resources to the central site.

I'm doing the same thing with Cisco RV042 with version V3 of the material, but I can't access the local router until the VPN breaks down. I can ' ping, SNMP the local router, or access but I can access the central site. Very strange.

Do you know what can I do to access the router local (for example, hardware V2) with connected VPN?

Thank you

Rafael

Just a hunch, but in the remote network you agree with what the network and subnet?

I've seen this symptom before.

LAN on the RV series.

10.10.2.0 255.255.255.0

Trust remote networks

10.10.1.0 255.255.248.0

It is traffic destined to the router on the 10.10.2.1 ip address is through the tunnel forward. So, for this purpose, you can only access the router LAN interface when the tunnel is out of service. I'm not sure why ping works but it does. I'm looking into this symptom on a different device, but the device has a similar graphical interface.

I would like to know if you have a similar setup.

Cisco Small Business Support Center

Randy Manthey

CCNA, CCNA - security

Comments of the virtual machine removes the packages using e1000 Mode VST adapter

We discovered a recent issue in our datacenter where our virtual machine guests will fall packages when using frames on the map virtual e1000 on a vSwitch configured for VST mode. The guest operating system is Red Hat Enterprise Linux 5 update 6.
Ignored packets occur when the MTU has 9000 on the Linux OS. The vSwitch is configured correctly for extended frames and we tested 2 virtual machines on the same hardware (and same VM network) as well as two different servers ESXi to verify this.
Our wireshark caputures revealed that the last 4 bytes of the payload of the packet are deleted. An example is the package of sending on a single server was 8142 bytes and package receiver 8138 bytes. Because of the difference, the TCP checksum fails and the packet is ignored. Somewhere by the transfer of the 802. 1 q header is missing on one end and on the other, less the last 4 bytes at the end of the frame.
So far, our only workaround is to set the MTU 1500 on the Linux OS or use with MTU 9000 VMXNET3 adapter. We use PXE to boot our virtual machines, that's why we chose to use the e1000 rather than the VMXNET3 adapter adapter (although RHEL 6 supports PXE with the new adapter, that's how good news in the future!)

Hello

You cannot use e1000 with frames jmbo it as design of esx, only enhanced vmxnet (and vmxnet3) adapters are supported of extended frames. Cards other than enhanced vmxnet (and vmxnet3) adapters, for example the adapter E1000, unusable with frames. Attempts to change the MTU seems to succeed but the adapter always deletes more than 1500 byte frames.
TM

The battery charge falls even when it is plugged into the satellite series

I have a laptop satellite and although it recognizes the power adapter when it is connected and that the icon in the taskbar shows "load", the percentage of the battery charge seems down.

It is only while the laptop is turned on, because it does not charge the battery when it is turned off.
I didn't know that he used the power of the battery so that hip, so I'm puzzled by this not only why the battery doesn't seem to be in charge, but also why the battery seems to fall once the laptop doesn't have to use it anyway.

Any help is appreciated!

Hello

I saw this problem on my own laptop in the past. even if the laptop is charging, the battery seems to fall in charge.

This indicates that the battery life is coming to an end, there are a limited number of cycles of load for a battery before it dies.
Also when you have the computer is off fresh is always lost at a considerable pace, because the battery is good, "die."

You can't do anything on this issue except to buy a new replacement battery for your laptop computer to a repair center authorized Toshiba. This should answer your question.

DV6-6190us AMD update package fails. Necessary for recommended MS hotfix

I get a blue screen of death after installing the recommended MS hotfix KB2670838 and using Internet EXPLORER 9. I stopped the problem by uninstalling the patch. Others on the MS for a report of similar problems with computers laptops HP and AMD switchable graphics card. MS advises prevention hot - fix for the moment and is apparently change an option until the issue is resolved.

One user said that he solved the problem by upgrading the AMD drivers to the latest version. I tried that with the HP sp55092.exe install package on the download page of my dv6. Installation fails with the helpful message "Application install: install package failed! The progress screen said it was installing the MS Visual C++ 2010 redistributable runtime. MsiInstaller gives error event 1013 with the text "product: Microsoft Visual C++ 2010 Redistributable - 10.0.30319 64 x ‑‑ A later version of Microsoft Visual C++ 2010 Redistributable - 10.0.30319 64 x is already installed."

Installed versions (x 86 & x 64) running on my computer are 10.0.3.40219. It seems that the package installer on HP support site cannot handle a newer version of the execution. I presume that the reason for the new version on my computer is software that relies on the SP1 version, so downgraded to the old version would just move the problem even if it gets the driver AMD installed package.

Anyone else seeing this? HP updates the installation package? Any ideas?

JoeM

Pavilion dv6-6190us; Win7 Home Premium 64

I shot the most recent version of the C++ 2010 runtime that blocked the Softpaq installation, installation fact and re-updated C++ 2010 runtime to the current version. The Softpaq, Intel and AMD drivers updated to the latest versions (on the site of HP). Then I reinstalled the MS fix and were broadcast for 12 hours, with no more BSODs.Funny thing is that the Softpaq still gave me an error on installation (relating to execution C++ 2010) but this time continued and completed.

I didn't want to steam. I'll look further and maintain the ITI in mind for future updates. It seems that HP is almost through with the software/firmware for the DV6s.

Thanks for your suggestions,

Joe

DROP PACKAGE

Hello
I would like to help.
I have the following problem:

Site studies Web has an application that runs on top of JWPlayer plugin (SWF), but the site is by permission of lists all the rules of content filtering with the firewall for full access, and yet this fall packages. The following Packet monitor log.

Number of packages: 419 *.
Header values:
Captured bytes: 131, actual bytes on the wire: 131
The package info (time: 19/04/2016 10:08:32.624):
in:-, out: X 0 *, IGNORED, Code Drop: 41, Id of Module: 26, (Ref.Id: _5057_txGsIboemfJqQlu), 2:2)
Ethernet header
Ether Type: IP(0x800), CBC is [d0:67:e5:bc:19:43], Dst = [02:17:c5:c1:28:b4]
IP packet header
Type of intellectual property: (0 x 6) TCP, Src = [192.168.16.1], Dst = [179.127.4.146]
TCP packet header
TCP Flags = [ACK, PSH,], [54994] = Src, Dst is [1935], Checksum = 0xff0d
The request header
Knows not
Value: [0]
Hex and ASCII dump of the package:
0217c5c1 28b4d067 08004500 00753549 00007f06 e5bc1943 *... (.. g... C E... u5I... *.
{7d7fc0a8 1001b37f 0492d6d2 078f6f86 fd8beb1d 33125018 *}... o... 3.P. *.
0100ff0d 0000957a 390f7828 be450fb2 330019be 83f630f5 *... z9.x (.) E.. 3... 0 *
2c2b98c0 8f3155f9 90 d 87738 6ca283d8 2d9779c6 ec81717d *, +... {1U... w8l... there... _ q} *.
d33347d4 4ff9b8d1 13c4f201 26c244a8 f0979015 6bcd66e1 *.3G. O.......&. D...k. f *.
(2920ec7d ac727756 bef71e *).}. rwV... *.

As SCR 192.168.16.1 my internal IP and the DST 179.127.4.146 the IP Address of the request.

in which I already identified the port and the 1935 and published in this control of the App.

Note: I use Google Translator to be able to create the text, I apologize for the errors. Thank you.

Problem solved, after placing the IP address in the list of IPS, blocking Exclusions occurred for a reason any within the App advanced control

Thank you

Send all VPN traffic and the other end it blocks Internet

Hello

I wonder if I can get a RV042 VPN Tunnel to a RV082 and in the RV082 block all traffic on the internet that comes form the computers that are behind the RV042.

Something like this:

Remote PC-> RV042-> VPN-> RV082-> firewall RV082 (block internet traffic, allow intranet traffic)

Thank you very much

Oliver

The scenario you describe should be doable with a pair of RV042 and RV082, where all traffic is transmitted by RV042 to RV082. What you need is to configure an access on RV082 rule to deny the RV042 subnet HTTP traffic to ALL (internet).

fall of site to site vpn icmp packets

Hello

I test site to site vpn between ASA and cisco router with GNS3, topology is base the tunnel is up but the question when the remote host ping from both sides it is drops icmp, see router command and ASA do not include droppings. Here is a sample output from ping when I try to remote client ping. any help is appreciated :)

Instant topology is attached, also configs

Thank you

84 bytes from 10.20.20.5 icmp_seq = 59 ttl = 63 times = 79,004 ms
10.20.20.5 icmp_seq = timeout 60
84 bytes from 10.20.20.5 icmp_seq = 61 = ttl 63 times = 70,004 ms
10.20.20.5 icmp_seq = timeout 62
84 bytes from 10.20.20.5 icmp_seq = ttl 63 time = 63 = 59,004 ms
10.20.20.5 icmp_seq = 64 timeout
84 bytes from 10.20.20.5 icmp_seq = 65 = ttl 63 times = 50,003 ms
10.20.20.5 icmp_seq = timeout 66
84 bytes from 10.20.20.5 icmp_seq = 67 ttl = 63 times = 59,003 ms
10.20.20.5 icmp_seq = timeout 68
84 bytes from 10.20.20.5 icmp_seq = 69 = ttl 63 times = 50,003 ms
10.20.20.5 icmp_seq = timeout 70
84 bytes from 10.20.20.5 icmp_seq = 71 ttl = 63 times = 58,003 ms
10.20.20.5 icmp_seq = timeout 72
84 bytes from 10.20.20.5 icmp_seq = 73 = ttl 63 times = 50,003 ms
10.20.20.5 icmp_seq = timeout 74
84 bytes from 10.20.20.5 icmp_seq = 75 ttl = 63 times = 69,004 ms
10.20.20.5 icmp_seq = timeout 76
84 bytes from 10.20.20.5 icmp_seq = 77 ttl = 63 times = 237,013 ms
10.20.20.5 icmp_seq = timeout 78

R1 ipsec crypto #sh her

Interface: FastEthernet0/0
Tag crypto map: map, local addr 100.100.100.2

protégé of the vrf: (none)
local ident (addr, mask, prot, port): (10.20.20.0/255.255.255.0/0/0)
Remote ident (addr, mask, prot, port): (10.20.10.0/255.255.255.0/0/0)
current_peer 100.100.100.1 port 500
LICENCE, flags is {origin_is_acl},
#pkts program: 14, #pkts encrypt: 14, #pkts digest: 14
decaps #pkts: 28, #pkts decrypt: 28, #pkts check: 28
compressed #pkts: 0, unzipped #pkts: 0
#pkts uncompressed: 0, #pkts compr. has failed: 0
#pkts not unpacked: 0, #pkts decompress failed: 0
Errors #send 0, #recv 0 errors

ciscoasa # sh crypto isakmp stats

Global statistics IKEv1
The active Tunnels: 1
Previous Tunnels: 1
In bytes: 1384
In the packages: 12
In packs of fall: 0
In Notifys: 8
In the constituencies of P2: 0
In P2 invalid Exchange: 0
In P2 Exchange rejects: 0
Requests for removal in his P2: 0
Bytes: 1576
Packet: 13
Fall packages: 0
NOTIFYs out: 16
Exchanges of P2: 1
The Invalides Exchange P2: 0
Exchange of P2 rejects: 0
Requests to remove on P2 Sa: 0
Tunnels of the initiator: 1
Initiator fails: 0
Answering machine fails: 0
Ability system breaks down: 0
AUTH failed: 0
Decrypt failed: 0
Valid hash fails: 0
No failure his: 0

Hello

On router R1, you gave the default route as output interface. Instead of using the output interface replace the IP address of the next hop. It will solve the issue of the reduction of ping.

IP route 0.0.0.0 0.0.0.0 FastEthernet0/0

IP route 0.0.0.0 0.0.0.0 100.100.100.1

HTH

"Please note the useful messages and mark the correct answer if it solves the problem."

How can I block a VPN from site to Site traffic

I configured a VPN from Site to Site, the wizard on a

ASA 5510 and it works.

However, I want to restrict http traffic only.

I tried to change the ACL entry that allows ip traffic to allow only http traffic, but that seems to block all traffic and translates into a journal entry:

Inbound TCP connection doesn't deny x to Y/80 SYN flags on the incoming interface.

I managed to block pings by entering an ACL rule to specifically deny icmp, but I would like to deny all except http.

Any advice on how to achieve this appreciated.

William.

Hello

Guess that's what you're looking for. See the Bidirectional VPN filter configuration section.

http://www.Cisco.com/en/us/products/HW/vpndevc/ps2030/products_configuration_example09186a00808c9a87.shtml

Send all traffic through the vpn tunnel

Does anyone know how to send all traffic through the tunnel vpn on both sides? I have a server EZVpn on one side and one EZVpn client on the other. I'm not natting on each side. I use the value default 'tunnelall' for the attributes of group policy. On the client side all traffic, even if not intended for the subnet of the side server, seems to pass through the tunnel. But if I ping the side server, the same rules don't seem to apply. Traffic destined for rates aside customer through the tunnel, but the traffic that is not pumped on the external interface in the clear. That's not cool.

Hello

Clinet traffic to server through tunnel, that's right, right?

Traffic from server to client through tunnel, but the rest of the traffic is not, no?

This works as expected because in ezvpn, politics of "tunnel all ' is for traffic is coming from the client., do not leave the server.

Side server, customer traffic will pass through tunnel, the rest used.

Sian

Procedure do not work in a package
Hello
I created a procedure that lists the files in a directory, this procedure work separately and the list of these files, but when I add the procedure to a package and run the package, it don't work & that it will return no error, it seems that the package Blons procedure.

Can someone suggest me something please.

Concerning
Have you defined the procedure to be starting for the package? Open the bag and do a right-click on the procedure and select the option called something like "Set as step to start. You should see a small green game icon appear in the corner of your object to the procedure. Run the package and the proc will run

Cannot call procedure/package wwv_flow_load_data.create_csv_collection

Hello

I have a pl/sql code in a process page that calls a procedure in a package. He worked at point 3.1, but does not work in 4.0.1.00.03.

declare
  l_first_row_is_col_name boolean := true;
  l_file_id               number := 0;
begin
  select id
    into l_file_id
    from apex_application_files
   where name = :P50_FILE;

  :P50_FILE_ID := l_file_id;

 wwv_flow_load_data.create_csv_collection (
  p_file_id                => l_file_id,
  p_separator              => ',',
  p_enclosed_by            => '"',
  p_first_row_is_col_name  => l_first_row_is_col_name,
  p_currency               => '$',
  p_numeric_chars          => '.,',
  p_charset                => 'utf-8'
  );
end;
{code}

here is the error:

ORA-06550: line 12, column 2:
PLS-00201: identifier 'WWV_FLOW_LOAD_DATA.CREATE_CSV_COLLECTION' must be declared
ORA-06550: line 12, column 2:
PL/SQL: Statement ignored

1. declare
2.   l_first_row_is_col_name boolean := true;
3.   l_file_id               number := 0;


It seems that the package/procedure is not valid so it is being interpreted as a variable, but it is valid in the schema APEX_040000.

Any suggestions are appreciated.

Thanks
Matt

Hello

I think that there is no synonym public wwv_flow_load_data.
You must create an and control the privileges for the apex_040000.wwv_flow_load_data package.

That is obviously not recommended because wwv_flow_load_data is the package without papers.

Kind regards
Jari

How to Package Extension of Photoshop cs4/cs5 with manifest.xml

Hello
TL; Dr: How can I present my extension for cs4 and cs5 in a way that respects the geometry of the window extension?
I have a panel that specifies the geometry of the window in its manifest.xml. When the Panel is installed in Photoshop panels / folder, the geometry is ignored, so I'll try to package the Panel as an extension to install via the extensions Manager. I ran into different issues for each version of CS. I read a certain PDF format on the extensions, UCF command line package manager, etc. and have not been able to find a solution that works for both platforms.
My understaning
My trial and error research has lead me to understand that the extension files must eventually end by in the (mac) / Library/Application Support/Adobe / < CSversion > ServiceManager/extensions/directory. In CS5, if the extension folder contains a manifest.xml file (ex: extensions/GuideGuide/CSXS/manifest.xml) that specifies the geometry of the window, Photoshop will meet this geometry of the window when the Panel opens. However, in CS4, it does not. In my tests, Photoshop CS4 does not seem to do anything with the file manifest.xml. Instead, I had to edit/Library/Application Support/Adobe/CS4ServiceManager/ServiceManifest.xml and add my extension to its content. Once I did, Photoshop CS4 launches my Panel and respect its window geometry.
The problem is that it is a manual installation. I can't ask my users to rummage through their system files to install my Panel. In addition, since it is unsigned by using this method, it will not work if they are not marked for debugging. I began to explore using the extensions Manager, but I ran into problems that I can't find ansers some PDFs on the packaging that I could find.
CS5 problems
If I use the UCF command-line tool, I can package and sign my file. He moved very well and does what I want. However, using this method, I have not been able to find a way to specify the author and description that appears in the extensions Manager.
Problems with CS4

UCF command-line tool does not seem that the packages that can be installed with CS4 and I could not find one that is compatible. I had to use the extension manager to package my extension based on a .mxi file. The problem I have here is the installation of files in this way to limit myself to put in the directory panels, which then causes the Panel to ignore the geometry of the window. Is it possible with a .mxi file to install in the/Library/Application Support/Adobe/< CSversion > ServiceManager/extensions/lib/and edit the file/Library/Application Support/Adobe/CS4ServiceManager/ServiceManifest.xml?
There must be, because Kuler and other extensions are installed.
Thank you for any assistance you can provide. I spent weeks trying to get this to work and have met nothing but dead ends and prosecutions of wild goose.

In manifest.xml to extension CSXS, 'Author' and 'Abstract' tags can be used to specify the name of the author and the description of the extension. Here is an example:

Adobe Systems Incorporated

[email protected]"/ >

http://www.Adobe.com">

This is the description of the extension

]]>

......

The extensions created by UCF command-line tool can be recognized by CS4 as the format has changed. It is impossible to install regular extensions to/Library/Application Support/Adobe/ServiceManager/extensions/directory. The extensions Manager does not provide any way to edit the file/Library/Application Support/Adobe/CS4ServiceManager/ServiceManifest.xml, either.

SSL VPN and routing problem

Hi all

I have a strange architecture including VPN and I have a few problems that I am not able to solve:

-J' use the ssl vpn gateway to allocate internal IP addresses of the local network described in the schema (8.8.2.0 or 8.8.3.0 according to the tunnel-group network.

-The purpose is for vpn clients directly access the internal network.

This works very well if there are strictly internal communications within the network. But recently, we have installed an application that needs to access both networks. No problem, I thought, but I was wrong, there seems to be a problem of routing inherent in the architecture in place.

Let me explain the problem:

-When I access the VPN, for example I will gave the 8.8.3.5 ip address.

-Im running the application that needs to open a page on the web server, located at 8.8.2.120

-l'asa receive my tcp syn datagram and forward it directly to the directly connected interface fa0/1 (based on the routing table)

-the web server returns the response, but he sends on its default gateway which is the cisco 6509.

-6509 it sends its vlan svi 2000

- and finally the ASA it receives on its interface fa0/2 but seems he falls as she opened a tcp on fa0/1 connection and receives the response on fa0/2.

I want it's traffic by tunnel to bypass the connected roads and transmit it to a default gateway of tunnel. This would ensure that the path for the request and the response would be the same.

I would like to know if there are orders of debugging for routing decisions validate my theory?

Do you know of any response to solve this problem?

Thanks a lot for your help.

When you configure the TCP State derivation always think ' which way is the SYN package coming?

Routing failed messages always have source and destination, are of course copied the entire message?

BTW, instead of letting clients SSL addresses attributed to vlan2000? Why not give them a separate subnet and the road back via correct interface?

I would also check your config and the routing :-) table

Marcin

critical update is not

[quote] have a serious update for security update security for Microsoft .NET Framework 4 on Windows XP, Windows Server 2003, Windows Vista, Windows 7, Windows Server 2008, Windows Server 2008 R2 for x 64 systems (KB2160841)

Download size: 3.6 MB

You may have to restart your computer for this update is taken into account.

Update type: Important

A security issue has been identified that could allow a malicious user to compromise your Windows system running the Microsoft .NET Framework and gain control full top. You can protect your computer by installing this update from Microsoft. After you install this item, you may have to restart your computer.

More information:
http://go.Microsoft.com/fwlink/?LinkId=194969

Help and Support:
http://support.Microsoft.com [/ quote]

This update has failed each time for the last few weeks, I uninstalled the live program that they seem to fall on me whenever I want Messenger to continue to not install certain adobe flashplayer update, still no joy on this update of crital or the update of Flash Player on the resettlement of live msn

whenever I shut down the computer at the end of a session he tries to complete an update and it fails even though I have not tried to install anything in this period... of ideas beyond the scrapping of the system and going to linux?

Hi MortDaWg,

Method 1:

Try to run the Windows Update Troubleshooter on your computer and check if the problem is resolved.

Reference:

Open the Windows Update troubleshooting tool
http://Windows.Microsoft.com/en-us/Windows7/open-the-Windows-Update-Troubleshooter

Method 2:

If the problem persists, try to install the stand-alone version of updates in cleanboot mode and check if it solves the problem.

To do this, you must enter the number of the Windows Update in the search field in the link provided below.

http://support.Microsoft.com/search/

Or try to download the stand-alone package of this link provided below.

http://www.Microsoft.com/downloads/en/details.aspx?FamilyId=bbc22169-996f-48D1-BEED-0ee0dc4fbf4f&displaylang=en

See this provided below Microsoft KB article to start your computer using the cleanboot.

How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7
http://support.Microsoft.com/kb/929135

Note: After a repair, be sure to set the computer to start as usual as mentioned in step 7 in the above article.

Method 3:

If the problem persists then I suggest you perform the steps mentioned in the link provided below.

The update is not installed successfully, you receive a message, and the computer restarts when you try to install an update in Windows Vista and Windows 7
http://support.Microsoft.com/kb/949358

Thank you, and in what concerns:
I. Suuresh Kumar - Microsoft technical support.

Visit our Microsoft answers feedback Forum and let us know what you think.

RV042 seems to fall packages/traffic

Similar Questions

Maybe you are looking for