RV0xx Version 3 VPN fell idle connection.

Similar Questions

• VPN does not connect in some places

  I have a laptop running v5 Cisco VPN Client that connects to the office of some places network fine, but not other places.  and in the places where it does not connect, it connects fine to another unrelated network.  by "does not connect", I mean that I can't access any of the resources on the office network - the client software seems to work, but there is no access, I cannot ping anything on the office network.  What would cause this?  Here is the log file from a location where it does not connect to the office network:

  Cisco Systems VPN Client 5.0.07.0290 Version
  Copyright (C) 1998-2010 Cisco Systems, Inc.. All rights reserved.
  Customer type: Windows, Windows NT
  Running: 6.1.7600
  Directory of config files: E:\Cisco systems VPN Client\

  1 21:36:30.625 07/03/11 Sev = WARNING/2 CVPND/0xE3400013
  AddRoute cannot add a route which the metric is 0: code 160
  Destination 5.0.0.0
  Subnet mask 255.0.0.0
  Gateway 192.36.253.1
  Interface 192.36.253.179

  2 21:36:30.625 07/03/11 Sev = WARNING/2 CM/0xA3100024
  Failed to add the route. Network: 5000000, subnet mask: ff000000, Interface: c024fdb3 Gateway: c024fd01.

  in this particular case, the local network uses the range of 192.168.1.x IP addresses, so that shouldn't be a problem.

  Lee

  Could you go through a PAT instrument, so you are not able to access resources after the VPN is connected because ESP packets usually will not go through a PAT tool.

  What must be configured on the VPN server is to allow NAT - t (NAT Traversal), IE: encapsulation of the ESP package in UDP or TCP packet, then it passes through PAT instrument very well.

  What server VPN should you terminate the VPN Client?

  The command to activate on the SAA would be: crypto isakmp nat-traversal 20

  Let me know if you have other devices like the VPN server.

  Hope that helps.

• VPN Client TCP connection to router IOS

  Hello

  I try to get a VPN client to connect via TCP to a router. I currently have the router put in place (and work) in using a VPN - UDP. Unfortunately one of the sites I visit will not allow VPN traffic outside of their firewall. I have searched all over the site of Cisco and can't find any information on the IOS configuration to accept TCP - VPN connections. I would like to change the TCP port 80, so my VPN traffic looks like just standard internet browsing my client firewall. Any links/pointer would be greatly appreciated.

  Thanks in advance!

  -Joe

  Take a look at this:

  http://www.Cisco.com/en/us/docs/iOS/12_2t/12_2t8/feature/guide/ftunity.html#wp1310210

  http://www.Cisco.com/en/us/docs/iOS/12_2t/12_2t8/feature/guide/ftunity.html#wp1305478

  http://www.Cisco.com/en/us/docs/iOS/12_2t/12_2t8/feature/guide/ftunity.html#wp1315635

  Please rate if useful.

  Concerning

  Farrukh

• Cisco vpn client to connect but can not access to the internal network

  Hi all

  I have a VPN configured on cisco 5540. My vpn was working fine, but suddenly there is a question that the cisco vpn client to connect but can not access to the internal network

  Any help would be much appreciated.

  Hi Samir,

  I suggest that you go to the ASA and check the configuration to make sure that it complies with the requirements according to the reference below link:

  http://www.Cisco.com/en/us/products/ps6120/products_configuration_example09186a00805734ae.shtml

  (The link above includes split tunneling, but this is just an option.

  Please paste the output of "sh cry ipsec his" here so that we can check if phase 2 is properly trained. I would say as you go to IPSEC vpn client on your PC and check increment in packets sent and received in the window 'status '.

  Let me know if this can help,

  See you soon,.

  Christian V

• My laptop still give me a version track even after the connection

  I downloaded CC on 2 Mac 1 desktop and 1 laptop.  My laptop still give me a version track even after the connection

  If it please try to disconnect from the creative cloud and reconnect. Try to follow:

  1. https://helpx.Adobe.com/x-productkb/policy-pricing/activation-network-issues.html
  2. https://helpx.Adobe.com/manage-account-membership/CC-reverts-to-trial.html

• Client VPN will not connect

  Hi all

  I have an ASA5508-x firewall on my scope. I want to connect from the internet using the VPN Client for admin purposes. I set it up and she asks and accept my password, but I get the error

  Group = VPN_CLIENT_ADMIN username = user.name, rejecting IP = X.X.X.X, IPSec tunnel: no entry for crypto for proxy card proxy remote 10.1.60.1/255.255.255.255/0/0 local 0.0.0.0/0.0.0.0/0/0 on the EXT_PUB_INT interface

  My config is

   ip local pool VPN_CLIENT_ADMIN 10.1.60.1-10.1.60.50 mask 255.255.255.0 object-group network VPN_CLIENTS description IP Range assigned to VPN Clients network-object 10.1.60.0 255.255.255.0 object-group network IND_LAN  description Internal LAN  network-object 192.168.1.0 255.255.255.0 access-list VPN_CLIENT_ADMIN extended permit ip object-group VPN_CLIENTS object-group IND_LAN nat (inside,EXT_PUB_INT) after-auto source static IND_LAN IND_LAN destination static VPN_CLIENTS VPN_CLIENTS no-proxy-arp group-policy VPN_CLIENT_ADMIN internal group-policy VPN_CLIENT_ADMIN attributes banner value Use of this connection is restricted to authorised users only. banner value Unauthorised or inappropriate use is prohibited and may be subject to administrative, criminal, banner value or civil penalties. This connection is monitored and logged. vpn-access-hours none vpn-simultaneous-logins 5 vpn-idle-timeout 30 vpn-session-timeout 180 vpn-filter value VPN_CLIENT_ADMIN vpn-tunnel-protocol ikev1 address-pools value VPN_CLIENT_ADMIN tunnel-group VPN_CLIENT_ADMIN type remote-access tunnel-group VPN_CLIENT_ADMIN general-attributes address-pool VPN_CLIENT_ADMIN authentication-server-group (EXT_PUB_INT) LOCAL default-group-policy VPN_CLIENT_ADMIN tunnel-group VPN_CLIENT_ADMIN ipsec-attributes ikev1 pre-shared-key *****

  I am running

   Cisco Adaptive Security Appliance Software Version 9.5(1) Device Manager Version 7.5(1)

  Any ideas why it might be failing?

  Thank you

  Hello

  Please share the output of sh run crypto map

  It seems that we have not a dynamic card configured we are cannot connect

  Thank you

  Shakti

• R8000 Open VPN drops Internet connection

  I have a router R8000 and sometimes when I go to connect by using the open VPN connection that it will show as connected but I don't have any internet access more. My connection log is below. The XXX is corresponding to my external IP address of the router.

  I have the service defined on the port UDP 12970 type. Firmware version: V1.0.3.4_1.1.2

  Journal will be in the next post, because there is a limit of 20,000 characters.

  In fact, I found a way around the problem. If you change the Protocol to TCP UDP everything works fine. Don't know what the problem is with UDP though.

• SSL - VPN can not connect - Windows 10

  Hello

  Our office has a SonicWall TZ105, with a more recent firmware, and now with Windows 10, we are unable to connect via SSL - VPN.  The user name and password are correct, and I can connect with the Android app.  But in Windows 10, I tried the MobileConnect App, the more recent mysonicwall NetExtender, used the terminal to create the VPN connection and just manually made a VPN connection and nothing works.

  The President of our company just got a new laptop and there 10 Windows, and I'm hitting a wall in the world, but need to get its connected to our office.

  Other VPN connections to other VPN servers work on this laptop, but not at our office.  He used to work with the same settings of router on Windows 7.

  Each different method of connection attempt is to give a different error.  The more strange to me, it's "the specified port is already open."  But there is no other connection to that port, and I am still able to connect using my phone.

  Any ideas?  Thanks in advance!

  I was able to solve the problem using the NetExtender 7.0.203, version downloaded from mysonicwall.com.  It was the only version (back to 5.0.?) that has been successfully can connect to our TZ105 with a laptop Win10 with all updates.

  I hope this helps someone else, I was pretty nearly pulling my hair out...

• Customer global VPN will not connect on the first attempt

  Global VPN Client version 4.9.4.0306.

  I connect to a variety of virtual private networks for clients whom I manage IT systems. When I connect to their virtual private networks via devices Sonicwall TZ in my home office, the first always uptight attempt connection, implementation service or Authenticating or IP acquisition. So I click on turn off, then immediately, click Activate, and it ends. This happens every time that I log in unless I log in no time (maybe a few minutes) after I close an open connection.

  I thought that it would be fair to my laptop; However, it has persisted through two or three versions of the GVPN customer and, more important still, this does not happen when I have my laptop in the office of a client with me - that from my desktop at home.

  So I already know that there must be something on my frontier DSL modem or a service. But it's not as if the customer VPN tells me "your modem has decided to abandon the Sonicwall response during authentication" or something like that.

  Are there measures of troubleshooting/diagnosis/tests of base I can try, or any configuration of particular gateway that could be suspicious. In my case, the gateway is my modem Frontier.

  Yes, it's a little different.

  Thank you for your participation!

  Chris

• iPad/iPhone VPN to ASA5510 connection

  I recently started getting reports of users of the iPad and iPhone that they can get is more the VPN on the SAA. User is iOS8. I don't have the AnyConnect to license activated on the SAA. I've upgraded to the ASA 8.2 (5) 57 that I installed a 3rd root certificate from Entrust. The previous version does not SHA - 2 support. Was - this chance end users were able to connect to the VPN from their mobile devices before the upgrade? If I have to activate the AnyConnect for Mobile license is it a license for each user or a license to cover all users. I have licensed AnyConnect Essentials with total number of Peer VPN for 250. During the trial of one of the iDevices ASDM logs do not indicate even an attempt to connect to the IP address of the device that I find it odd as well.

  A Mobile license must cover all

  http://www.Cisco.com/c/en/us/support/docs/security/Adaptive-Security-app...

  Kind regards

  Sandra

• 506th PIX and VPN client - multiple connections connections

  I have a PIX of the 506th (6.2) w/3DES license and 3.6.3 VPN client software. I'm only using group user name and password to authenticate. The first user login works fine. When the second user connects, the first is finished and the second works very well. The product turned on States I should be able to have 25 simultaneous connections or site to site or customer.

  Any help will be greatly appreciated, Kyle

  Are these two users on the same site, behind a device that makes PAT? If so, then this device is causing the problem, not the PIX. The device is unable to correctly translate the IPsec packets. Unfortunately nothing you can do about it on the PIX, although the next version of the software (6.3 to your calendar of March) will have NAT - T support (which the client currently supports). Once that support NAT - T both ends, they'll be able to say that there's a PAT instrument between the two and they will automatically encapsulate everything in the UDP packets, which your PAT instrument will be able to translate correctly.

• VPN client idle timeout (need to order)

  Hello Experts,

  I have the current configuration:

  Router Cisco 3700 and a version of the client vpn cisco 4.7

  I would like to know what is the command set up on the router so that my vpn clients may be inactive for 1 hour or more without having previously disconnected.

  Thank you very much

  Randall

  Hi Randall,.

  You can use the following command to increase the idle-timeout:

  cry dynamic-map 1

  all security association idle time<60-86400s>

  output

  * Please rate if this helped.

  -Kanishka

• Get VPN client to connect, but request timed out when ping

  Hi, I use the router Cisco 837 as my VPN server. I am connected using Cisco VPN Client Version 5. But when I ping the ip of the router, I have request timed out. Here is my configuration:

  Building configuration... Current configuration : 3704 bytes ! version 12.4 no service pad service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname michael ! boot-start-marker boot-end-marker ! memory-size iomem 5 no logging console enable secret 5 $1$pZLW$9RZ8afI8QdGRq0ssaEJVu0 ! aaa new-model ! ! aaa authentication login default local aaa authentication login sdm_vpn_xauth_ml_1 local aaa authorization exec default local aaa authorization network sdm_vpn_group_ml_1 local ! aaa session-id common ! resource policy ! ip subnet-zero no ip dhcp use vrf connected ip dhcp excluded-address 192.168.1.1 ! ip dhcp pool michael    network 192.168.1.0 255.255.255.0    default-router 192.168.1.1    dns-server 202.134.0.155 ! ip dhcp pool excluded-address    host 192.168.1.4 255.255.255.0    hardware-address 01c8.d719.957a.b9 ! ! ip cef ip name-server 202.134.0.155 ip name-server 203.130.193.74 vpdn enable ! ! ! ! username michael privilege 15 secret 5 $1$ZJQu$KDigCvYWKkzuzdYHBEY7f. username danny privilege 10 secret 5 $1$BDs.$Ez0u9wY7ywiBzVd1ECX0N/ ! ! ! crypto isakmp policy 1 encr 3des authentication pre-share group 2 crypto isakmp xauth timeout 15 ! crypto isakmp client configuration group michaelvpn key vpnpassword pool SDM_POOL_1 acl 199 netmask 255.255.255.0 ! ! crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac ! crypto dynamic-map SDM_DYNMAP_1 1 set transform-set ESP-3DES-SHA ! ! crypto map SDM_CMAP_1 client authentication list sdm_vpn_xauth_ml_1 crypto map SDM_CMAP_1 isakmp authorization list sdm_vpn_group_ml_1 crypto map SDM_CMAP_1 client configuration address respond crypto map SDM_CMAP_1 65535 ipsec-isakmp dynamic SDM_DYNMAP_1 ! ! ! interface Ethernet0 description $FW_INSIDE$ ip address 192.168.1.1 255.255.255.0 ip nat inside ip virtual-reassembly ip tcp adjust-mss 1452 hold-queue 100 out ! interface Ethernet2 no ip address shutdown hold-queue 100 out ! interface ATM0 no ip address no atm ilmi-keepalive dsl operating-mode auto pvc 0/35   pppoe-client dial-pool-number 1 ! ! interface FastEthernet1 duplex auto speed auto ! interface FastEthernet2 duplex auto speed auto ! interface FastEthernet3 duplex auto speed auto ! interface FastEthernet4 duplex auto speed auto ! interface Virtual-PPP1 no ip address ! interface Dialer1 description $FW_OUTSIDE$ mtu 1492 ip address negotiated ip nat outside ip virtual-reassembly encapsulation ppp dialer pool 1 ppp chap hostname ispusername ppp chap password 0 isppassword ppp pap sent-username ispusername password 0 isppassword crypto map SDM_CMAP_1 ! ip local pool SDM_POOL_1 192.168.2.1 192.168.2.5 ip classless ip route 0.0.0.0 0.0.0.0 Dialer1 ip http server no ip http secure-server ! ip nat inside source static udp 192.168.1.0 1723 interface Dialer1 1723 ip nat inside source static tcp 192.168.1.4 21 interface Dialer1 21 ip nat inside source route-map SDM_RMAP_1 interface Dialer1 overload ! access-list 1 remark SDM_ACL Category=16 access-list 1 permit 192.0.0.0 0.255.255.255 access-list 102 remark SDM_ACL Category=2 access-list 102 deny   ip 192.168.1.0 0.0.0.255 192.168.2.0 0.0.0.255 access-list 102 permit ip 192.168.1.0 0.0.0.255 any access-list 199 permit ip 192.168.1.0 0.0.0.255 192.168.2.0 0.0.0.255 route-map SDM_RMAP_1 permit 1 match ip address 102 ! ! control-plane ! banner motd ^C Authorized Access Only UNAUTHORIZED ACCESS TO THIS DEVICE IS PROHIBITED You must have explicit permission to access this device. All activities performed on this device are logged. Any violations of access policy will result in disciplinary action. ^C ! line con 0 no modem enable line aux 0 line vty 0 4 ! scheduler max-task-time 5000 end
  
  Thank you, anny help will be appreciated.
  			 
  Hi Michael,
  I have been through the newspapers, they are not conclusive and only detrmine that Phase 1 is coming. However according to this error message % SYS-2-BADSHARE: Bad refcount in pak_enqueue, ptr = 81B50AD8, count = 0 we are hiiting a bug on ios. The id of the bug is CSCsl24693 and the solution is to switch to 12.4 (11) XJ.
  Can you re-execute him debugs and send me the detailed results.
  Kind regards
  Aman
  		   

• RoboHelp HTML version 9 edition failed to connect to RoboHelp Server 9

  As an administrator for our RoboHelp Server (version 9), I created "Author" rights of access for a person.  This person is a technical writer who works remotely.  He tried to publish his Office RoboHelp HTML (version 9) to our RoboHelp Server software, but has encountered an error in publication. What is causing this error and what would be a solution to this problem?

  A screenshot and the text of the error is listed below:

  WebHelp Pro

  The publication has been cancelled.

  The connection has failed.  Please check the connection and post it again.

  Native error. Not allowed.

  BTW, in the setting of the screenshots, it is best to use the camera icon, you see in the toolbar when you write your answer.

  My guess is that some kind of configuration of the authorization was missed.

  It is also difficult to know where to start because the author is "remote." What is VPN? Or remote desktop or what?

  I'll start with the obvious.

  It could simply be that when the author generates the SSL Pro of WebHelp, the Edit Destination dialog box may be incomplete. I myself did fill the news shows this screenshot, I forgot to choose a box help or put in a wrong password. So, definitely check this first.

  

  Then, you or your administrator must check the user account, group and the area of the author is correctly configured.

  This screenshot shows that a group was created (in this case, called authors) and individual users have been assigned.

  

  Finally, the Group of the authors must be assigned to a region and publication rights .

  

  You can also watch this thread dealing with similar issues and solution.

  http://forums.Adobe.com/message/4162467#4162467

  After that, it might have something to do with the remote author permissions to access the destination of publication (the machine that RoboHelp Server) from a remote location and has nothing to do with the side of RoboHelp permissions!

  That's the best I can do where I sit. Let us know if solve you the problem.

  John Daigle

  Adobe Certified RoboHelp and Captivate instructor

  Evergreen, Colorado

  www.showmethedemo.com

• I'm unable to update to the new version, "refusing to proxy server connection.

  I am running version 3.6.3 right now and I was not able to do the latest updates updated, because once that I go through the download process and to launch Firefox I get the message "proxy server refuses connections please try again later, and I'm unable to access the internet unless I redo the 3.6.3 installation.» Anyone who has the magic answer would be great, because I have to go through this process every day when I get on my laptop...

  If you were using Firefox 3.6. 4 or higher, a new preference has been added to the preferences of the proxy connection settings in tools > Options > Advanced Options > > tab network - connection = settings = use system proxy settings

  If you do not select no proxy and restart Firefox your problem should be solved.