Same material, cannot vmotion. Stops at 13% with a general system error occurred: invalid argument.
I have four IBM (now Lenovo) x 3550 M4 (7914AC1) hosts that have been purchased by groups of two, several months apart. Those purchased at the same time can vmotion between them but they cannot vmotion with those bought later OR with one of our older infrastructure (Nehalem IBM level - x 3650 M3, M3 x 3550, etc.). The most recent M4 can talk to the fine old hosts. Can I migrate invited powered down.
VMware support was not able to give any help on this matter and have lost instead of my time (including do not contact me for weeks and also current exit without changing to another engineer; manager failed in this regard, too).
I pulled the material apart - I can say it's all the same material (looks the same, has the same numbers and RUF). The machines were configured the same.
Firmware isn't exactly the same thing on the material but is VERY close. I have one of each generation updated with the same Xpresspacks of IBM, and so except for the image diagnosis of pre-start, I think that they are the same. I'll check this again once then.
VMware drivers are the same. They were not. They are now. I got 5.5 latest drivers for everything that I can find a driver for (including cards CF - using the driver Qlogic native VMware NICS (igb); approx 10 GB (not being use IGB but fact still); the provider CIM, MegaRAID controller. I used VUM update their last 5.5 (standard license) with all the patches. vCenter is a 5.5 vCSA was last updated. I went into the BIOS settings side-by-side and ensured that everything is the same. I did the same thing with everything I could think of in vSphere (found about 5 differences, but nothing fixed).
Management is the network of vMotion. It's on the same VLAN as one of those guests are on (the clients are spread over 5 different VLAN). VMware support put in place a different vSwitch for vMotion with no luck.
The symptoms are the same regardless of their orientation (old to the new, new to the former) and don't care about the type of virtual machine (Windows 2008R2, CentOS 5.5, RHEL 6.7) or at the level of the material (VM 10 or 7 VM). It also fails if it is standard or high priority or if it is with the web client or the Windows client.
The place with the most characteristic symptom that doesn't show anywhere in googleland except to the pastebin is in the file /scratch/log/hostd.log of the host. The host that sends the guest throws a vmsvc.vm error VMotionCmdCb [1461010590046389] 'a': error - 6: invalid argument.
If anyone else has seen this (obviously someone because it is on pastebin) and understood, please enlighten me.
Thank you!
Jeff
These are the two hostd.log files (most recent, from the host first, then older receiver host).
-----------------------
From Server hostd.log:
-----------------------
2016 04-18 T 20: 16:29.927Z [37501 B 70 verbose "Default" opID = user F2241F42 - 000018 D 1-64-1 b = vpxuser] AdapterServer: target ='vim. VirtualMachine:2', method = "refreshStorageInfo".
2016 04-18 T 20: 16:29.956Z [37501 B 70 'Hbrsvc' verbose opID = F2241F42 - 000018 D 1-64-1 b user = vpxuser] Replicator: VmFileProviderCallback VM (id = 2).
2016 04-18 T 20: 16:29.972Z [37501 B 70 verbose opID "Default" = cb7f34c4 user = vpxuser] AdapterServer: target ='vim. PerformanceManager: ha-perfmgr ", method = 'GetPerfCounter'"
2016 04-18 T 20: 16:29.978Z [37280 B 70 'Local' verbose opID = cb7f34c4 user = vpxuser] Default resource used for "counter.vsanDomObj.writeThroughput.summary" planned for the module "perf."
2016 04-18 T 20: 16:29.992Z [37280 B 70 verbose opID "Default" = cb7f34c4 user = vpxuser] AdapterServer: target ='vim. HostSystem: ha-host ", method = 'retrieveInternalCapability'"
2016 04-18 T 20: 16:29.993Z [37280 B 70 verbose opID "Default" = cb7f34c4 user = vpxuser] AdapterServer: target ='vim. PerformanceManager: ha-perfmgr ", method = 'queryPerfCounterInt'"
2016 04-18 T 20: 16:30.002Z [37280 B 70 verbose opID "Default" = cb7f34c4 user = vpxuser] AdapterServer: target ='vim. LicenseManager: ha-license-manager ", method = 'GetLicenses'"
2016 04-18 T 20: 16:30.002Z [37280 B 70 verbose 'Vimsvc.ha - License-Manager' opID = cb7f34c4 user = vpxuser] load: existing file loading: /etc/vmware/license.cfg
2016 04-18 T 20: 16:30.014Z [37280 B 70 verbose opID "Default" = cb7f34c4 user = vpxuser] ha-license-manager: validate-> valid license found for "VMware ESX Server 5.0" (lastError = 0, desc.) IsValid:Yes)
2016 04-18 T 20: 16:30.172Z [35981 B 70 verbose opID "Default" = F2241F42 - 000018 D 1-64-a2-71 user = vpxuser] AdapterServer: target ='vim.host.VMotionManager:ha - vmotionmgr ", method ="prepareSourceEx"
2016 04-18 T 20: 16:30.172Z [37280 B 70 info 'Vcsvc.VMotion' opID = F2241F42 - 000018 D 1-64-a2-71 user = vpxuser] PrepareSourceEx [1461010590046389], VM = '2'
2016 04-18 T 20: 16:30.172Z [37280 B 70 info "Vcsvc.VMotionSrc (1461010590046389)" opID = F2241F42 - 000018 D 1-64-a2-71 user = vpxuser] VMotionEntry: migrateType = 1
2016 04-18 T 20: 16:30.172Z [37280 B 70 verbose opID ' Vcsvc.VMotionSrc (1461010590046389) "F2241F42 - 000018 D 1-64-a2-71 = user = vpxuser] JrnlCreate: created 1461010590.14
2016 04-18 T 20: 16:30.172Z [37280 B 70 "Vmsvc.vm:/vmfs/volumes/526aca09-9e531e90-b07b-e61f135547a7/guestvm.mydomain.edu/guestvm.mydomain.edu.vmx" info opID = F2241F42 - 000018 D 1-64-a2-71 user = vpxuser] Transition State (VM_STATE_ON-> VM_STATE_EMIGRATING)
2016 04-18 T 20: 16:30.172Z [info 37280 B 70 ' Vmsvc.vm:/vmfs/volumes/526aca09-9e531e90-b07b-e61f135547a7/guestvm.mydomain.edu/guestvm.mydomain.eduvmx' opID = F2241F42 - 000018 D 1-64-a2-71 user = vpxuser] VMotionPrepare (1461010590046389): sending "to" srcIp = 10.10.6.108 supporting = 10.10.6.73, type = 1, encrypted = false, remoteThumbprint = 28, 5 C: C3:9 C: 3E:BA:79:EA:B5:19:CC:A9:36:34:C1:10:48:46:F0:0E
2016 04-18 T 20: 16:30.172Z [info 37280 B 70 ' Vmsvc.vm:/vmfs/volumes/526aca09-9e531e90-b07b-e61f135547a7/guestvm.mydomain.edu/guestvm.mydomain.edu.vmx ' opID = F2241F42 - 000018 D 1-64-a2-71 user = vpxuser] VMotionPrepare: = srcLoggingIp
2016 04-18 T 20: 16:30.172Z [info 37280 B 70 ' Vmsvc.vm:/vmfs/volumes/526aca09-9e531e90-b07b-e61f135547a7/guestvm.mydomain.edu/guestvm.mydomain.edu.vmx ' opID = F2241F42 - 000018 D 1-64-a2-71 user = vpxuser] VMotionPrepare: = dstLoggingIp
2016 04-18 T 20: 16:30.172Z [info 37280 B 70 ' Vmsvc.vm:/vmfs/volumes/526aca09-9e531e90-b07b-e61f135547a7/guestvm.mydomain.edu/guestvm.mydomain.edu.vmx ' opID = F2241F42 - 000018 D 1-64-a2-71 user = vpxuser] VMotionPrepare: srcMgmtIp = 10.10.6.108
2016 04-18 T 20: 16:30.172Z [info 37280 B 70 ' Vmsvc.vm:/vmfs/volumes/526aca09-9e531e90-b07b-e61f135547a7/guestvm.mydomain.edu/guestvm.mydomain.edu.vmx ' opID = F2241F42 - 000018 D 1-64-a2-71 user = vpxuser] VMotionPrepare: dstMgmtIp = 2620:91:0:96:73
2016 04-18 T 20: 16:30.172Z [37280 B 70 "Vmsvc.vm:/vmfs/volumes/526aca09-9e531e90-b07b-e61f135547a7/guestvm.mydomain.edu/guestvm.mydomain.edu.vmx" info opID = F2241F42 - 000018 D 1-64-a2-71 user = vpxuser] VMotionPrepare: = dstVmDirPath / vmfs/volumes/526aca09-9e531e90-b07b-e61f135547a7 /guestvm.mydomain.edu/.
2016 04-18 T 20: 16:30.172Z [info 37280 B 70 ' Vmsvc.vm:/vmfs/volumes/526aca09-9e531e90-b07b-e61f135547a7/guestvm.mydomain.edu/guestvm.mydomain.edu.vmx ' opID = F2241F42 - 000018 D 1-64-a2-71 user = vpxuser] VMotionPrepare: dstVmFileName =guestvm.mydomain.edu.vmx
2016 04-18 T 20: 16:30.173Z [37280 B 70 "Vmsvc.vm:/vmfs/volumes/526aca09-9e531e90-b07b-e61f135547a7/guestvm.mydomain.edu/guestvm.mydomain.edu.vmx" info opID = F2241F42 - 000018 D 1-64-a2-71 user = vpxuser] SetVmdbVirtualDeviceChange: deviceChange # 0
SIOC: SIOC is not notified to start the injector
2016 04-18 T 20: 16:30.173Z [37280 B 70 verbose opID ' Vcsvc.VMotionSrc (1461010590046389) "F2241F42 - 000018 D 1-64-a2-71 = user = vpxuser] Migration changed state from NONE to BEGIN
2016 04-18 T 20: 16:30.173Z [37280 B 70 info 'Vcsvc.VMotion' opID = F2241F42 - 000018 D 1-64-a2-71 user = vpxuser] finished scheduling PrepareSourceEx [1461010590046389].
2016 04-18 T 20: 16:30.173Z [' info 36591 B 70 ' vm: / vmfs/volumes/526aca09-9e531e90-b07b-e61f135547a7 /guestvm.mydomain.edu/guestvm.mydomain.edu.vmx "] disconnect the current control.
2016 04-18 T 20: 16:30.173Z [FFA4FB70 verbose opID "Default" = F2241F42 - 000018 D 1-64-a2-71 user = vpxuser] AdapterServer: target ='vmodl.query.PropertyCollector:ha - property-collector ", method = 'createFilter'"
2016 04-18 T 20: 16:30.174Z [info 372C1B70 ' Vmsvc.vm:/vmfs/volumes/526aca09-9e531e90-b07b-e61f135547a7/guestvm.mydomain.edu/guestvm.mydomain.edu.vmx '] VMotionCmdCb [1461010590046389] 'a': error - 6: invalid argument
2016 04-18 T 20: 16:30.174Z [info 372C1B70 ' Vmsvc.vm:/vmfs/volumes/526aca09-9e531e90-b07b-e61f135547a7/guestvm.mydomain.edu/guestvm.mydomain.edu.vmx '] VMotionCmdCb [1461010590046389]: prepare the job completed with error vmodl.fault.SystemError
2016 04-18 T 20: 16:30.174Z [372C1B70 verbose 'Vmsvc.vm:/vmfs/volumes/526aca09-9e531e90-b07b-e61f135547a7/guestvm.mydomain.edu/guestvm.mydomain.edu.vmx"] VMotionCmdCb: shooting ResolveCb
2016 04-18 T 20: 16:30.174Z [372C1B70 info ' Vcsvc.VMotionSrc (1461010590046389) "] ResolveCb: VMX reports needsUnregister = false for migrateType MIGRATE_TYPE_VMOTION
2016 04-18 T 20: 16:30.174Z [372C1B70 info ' Vcsvc.VMotionSrc (1461010590046389) "] ResolveCb: failed with error: {(vmodl.fault.SystemError)
-> dynamicType = < unset >
-> faultCause = (vmodl. NULL in MethodFault),
-> reason = "Invalid Argument."
-> msg = ""
->}
2016 04-18 T 20: 16:30.174Z [verbose 372C1B70 "Vcsvc.VMotionSrc (1461010590046389)"] Migration changed State to BEGIN done
2016 04-18 T 20: 16:30.174Z [verbose 372C1B70 "Vcsvc.VMotionSrc (1461010590046389)"] called finished
2016 04-18 T 20: 16:30.174Z [372C1B70 "Vmsvc.vm:/vmfs/volumes/526aca09-9e531e90-b07b-e61f135547a7/guestvm.mydomain.edu/guestvm.mydomain.edu.vmx" info] State of Transition (VM_STATE_EMIGRATING-> VM_STATE_ON)
2016 04-18 T 20: 16:30.174Z [37280 B 70 'Hostsvc' verbose] change of State received for VM ' 2'
2016 04-18 T 20: 16:30.174Z [37280 B 70 'Guestsvc.GuestFileTransferImpl' info] entered VmPowerStateListener
2016 04-18 T 20: 16:30.174Z [37280 B 70 'Guestsvc.GuestFileTransferImpl' info] successful VmPowerStateListener
2016 04-18 T 20: 16:30.174Z [37280 B 70 'Hbrsvc' info] Replicator: powerstate change VM: 2 old: 1 new: 1
2016 04-18 T 20: 16:30.174Z ['Hostsvc' 372C1B70 info] decremented SIOC injector Flag2
2016 04-18 T 20: 16:30.174Z [372C1B70 "Vmsvc.vm:/vmfs/volumes/526aca09-9e531e90-b07b-e61f135547a7/guestvm.mydomain.edu/guestvm.mydomain.edu.vmx" info] VMotion finished cleaning
2016 04-18 T 20: 16:30.174Z [verbose 372C1B70 "Vcsvc.VMotionSrc (1461010590046389)"] JrnlEnd: writes active = 0
2016 04-18 T 20: 16:30.174Z [verbose 372C1B70 "Vcsvc.VMotionSrc (1461010590046389)"] JrnlEnd: finished journal
2016 04-18 T 20: 16:30.175Z [verbose 372C1B70 "Vcsvc.VMotionSrc (1461010590046389)"] /var/lib/vmware/hostd/journal/1461010590.14 [JrnlFilePersistenceProvider::DeleteJournal] removal.
2016 04-18 T 20: 16:30.175Z [verbose 372C1B70 "Vcsvc.VMotionSrc (1461010590046389)"] JrnlDelete: deleted journal
2016 04-18 T 20: 16:30.175Z [37280 B 70 'Hbrsvc' verbose] Replicator: Remove only group no entry for VM (id = 2)
2016 04-18 T 20: 16:30.180Z [37501 B 70 verbose opID "Default" = F2241F42 - 000018 D 1-64-a2-71 user = vpxuser] AdapterServer: target='vmodl.query.PropertyCollector.Filter:session[574b3c38-6a6b-214e-4bf3-428b10abded9]52760c3e-4722-159c-5c3a-df6eb23ddbbc ", method = 'destroy'
2016 04-18 T 20: 16:30.201Z [372C1B70 verbose opID "Default" = 44d5f9ee user = vpxuser] AdapterServer: target ='vim. PerformanceManager: ha-perfmgr ", method = 'GetPerfCounter'"
2016 04-18 T 20: 16:30.207Z [372C1B70 verbose 'Local' opID = 44d5f9ee user = vpxuser] Default resource used for "counter.vsanDomObj.writeThroughput.summary" planned for the module "perf."
2016 04-18 T 20: 16:30.223Z [37501 B 70 verbose opID "Default" = 44d5f9ee user = vpxuser] AdapterServer: target ='vim. HostSystem: ha-host ", method = 'retrieveInternalCapability'"
2016 04-18 T 20: 16:30.224Z [372C1B70 verbose opID "Default" = 44d5f9ee user = vpxuser] AdapterServer: target ='vim. PerformanceManager: ha-perfmgr ", method = 'queryPerfCounterInt'"
2016 04-18 T 20: 16:31.162Z [35981 B 70 verbose 'SoapAdapter"] responded to the request of the State of service
2016 04-18 T 20: 16:31.314Z [35981 B 70 verbose opID 'Default' F2241F42 - 000018 D 1-64-a2-b7 = user = vpxuser] AdapterServer: target ='vim.host.VMotionManager:ha - vmotionmgr ", method ="completeSource"
2016 04-18 T 20: 16:31.314Z [37501 B 70 info 'Vcsvc.VMotion' opID = F2241F42 - 000018 D 1-64-a2-b7 user = vpxuser] CompleteSource [1461010590046389]
2016 04-18 T 20: 16:31.320Z [35981 B 70 verbose opID "Default" = 8590ebdf user = vpxuser] AdapterServer: target ='vim. PerformanceManager: ha-perfmgr ", method = 'GetPerfCounter'"
2016 04-18 T 20: 16:31.326Z [35981 B 70 'Local' verbose opID = 8590ebdf user = vpxuser] Default resource used for "counter.vsanDomObj.writeThroughput.summary" planned for the module "perf."
2016 04-18 T 20: 16:31.340Z [35981 B 70 verbose opID "Default" = 8590ebdf user = vpxuser] AdapterServer: target ='vim. HostSystem: ha-host ", method = 'retrieveInternalCapability'"
2016 04-18 T 20: 16:31.342Z [37501 B 70 verbose opID "Default" = 8590ebdf user = vpxuser] AdapterServer: target ='vim. PerformanceManager: ha-perfmgr ", method = 'queryPerfCounterInt'"
2016 04-18 T 20: 16:31.356Z [35981 B 70 verbose opID "Default" = 8590ebdf user = vpxuser] AdapterServer: target ='vim. LicenseManager: ha-license-manager ", method = 'GetLicenses'"
2016 04-18 T 20: 16:31.356Z [35981 B 70 verbose 'Vimsvc.ha - License-Manager' opID = 8590ebdf user = vpxuser] load: existing file loading: /etc/vmware/license.cfg
2016 04-18 T 20: 16:31.371Z [35981 B 70 verbose opID "Default" = 8590ebdf user = vpxuser] ha-license-manager: validate-> valid license found for "VMware ESX Server 5.0" (lastError = 0, desc.) IsValid:Yes)
-----------------------
Hostd.log of the reception host:
-----------------------
2016 04-18 T 20: 16:29.798Z [FFD35B70 'Hostsvc.DvsManager' verbose] called PersistAllDvsInfo
2016 04-18 T 20: 16:30.245Z [29940 B 70 verbose opID "Default" = ac976ee5 user = vpxuser] AdapterServer: target ='vim. PerformanceManager: ha-perfmgr ", method = 'GetPerfCounter'"
2016 04-18 T 20: 16:30.251Z [29940 B 70 'Local' verbose opID = ac976ee5 user = vpxuser] Default resource used for "counter.vsanDomObj.writeThroughput.summary" planned for the module "perf."
2016 04-18 T 20: 16:30.265Z [29940 B 70 verbose opID "Default" = ac976ee5 user = vpxuser] AdapterServer: target ='vim. HostSystem: ha-host ", method = 'retrieveInternalCapability'"
2016 04-18 T 20: 16:30.267Z [29940 B 70 verbose opID "Default" = ac976ee5 user = vpxuser] AdapterServer: target ='vim. PerformanceManager: ha-perfmgr ", method = 'queryPerfCounterInt'"
2016 04-18 T 20: 16:31.412Z [2BAC2B70 verbose opID "Default" = F2241F42 - 000018 D 1-64-a2-e5 user = vpxuser] AdapterServer: target ='vim.host.VMotionManager:ha - vmotionmgr ", method ="completeDestination"
2016 04-18 T 20: 16:31.412Z [2BAC2B70 info 'Vcsvc.VMotion' opID = F2241F42 - 000018 D 1-64-a2-e5 user = vpxuser] CompleteDestination [1461010590046389]
2016 04-18 T 20: 16:31.412Z [2BAC2B70 WARNING opID "Vcsvc.VMotion" = F2241F42 - 000018 D 1-64-a2-e5 user = vpxuser] CompleteDestination: card not found
2016 04-18 T 20: 16:31.417Z [29940 B 70 verbose opID "Default" = fa72f2f7 user = vpxuser] AdapterServer: target ='vim. PerformanceManager: ha-perfmgr ", method = 'GetPerfCounter'"
2016 04-18 T 20: 16:31.424Z [29940 B 70 'Local' verbose opID = fa72f2f7 user = vpxuser] Default resource used for "counter.vsanDomObj.writeThroughput.summary" planned for the module "perf."
2016 04-18 T 20: 16:31.439Z [FFD35B70 verbose opID "Default" = fa72f2f7 user = vpxuser] AdapterServer: target ='vim. HostSystem: ha-host ", method = 'retrieveInternalCapability'"
2016 04-18 T 20: 16:31.441Z [29940 B 70 verbose opID "Default" = fa72f2f7 user = vpxuser] AdapterServer: target ='vim. PerformanceManager: ha-perfmgr ", method = 'queryPerfCounterInt'"
Using IPv6 on new hosts? If so, try disabling:
2016 04-18 T 20: 16:30.172Z [37280 B 70 info 'Vmsvc.vm:/vmfs/volumes/526aca09-9e531e90-b07b-e61f135547a7/guestvm.mydomain.edu/guestvm.mydomain.eduvmx' opID = F2241F42 - 000018 D 1-64-a2-71 user = vpxuser] VMotionPrepare (1461010590046389): sending "to" srcIp = 10.10.6.108 supporting = 10.10.6.73, type = 1, encrypted = false, remoteThumbprint = 28, 5 C: C3:9 C: 3E:BA:79:EA:B5:19:CC:A9:36:34:C1:10:48:46:F0:0E
2016 04-18 T 20: 16:30.172Z [37280 B 70 info 'Vmsvc.vm:/vmfs/volumes/526aca09-9e531e90-b07b-e61f135547a7/guestvm.mydomain.edu/guestvm.mydomain.edu.vmx' opID = F2241F42 - 000018 D 1-64-a2-71 user = vpxuser] VMotionPrepare: = srcLoggingIp
2016 04-18 T 20: 16:30.172Z [37280 B 70 info 'Vmsvc.vm:/vmfs/volumes/526aca09-9e531e90-b07b-e61f135547a7/guestvm.mydomain.edu/guestvm.mydomain.edu.vmx' opID = F2241F42 - 000018 D 1-64-a2-71 user = vpxuser] VMotionPrepare: = dstLoggingIp
2016 04-18 T 20: 16:30.172Z [37280 B 70 info 'Vmsvc.vm:/vmfs/volumes/526aca09-9e531e90-b07b-e61f135547a7/guestvm.mydomain.edu/guestvm.mydomain.edu.vmx' opID = F2241F42 - 000018 D 1-64-a2-71 user = vpxuser] VMotionPrepare: srcMgmtIp = 10.10.6.108
2016 04-18 T 20: 16:30.172Z [37280 B 70 info 'Vmsvc.vm:/vmfs/volumes/526aca09-9e531e90-b07b-e61f135547a7/guestvm.mydomain.edu/guestvm.mydomain.edu.vmx' opID = F2241F42 - 000018 D 1-64-a2-71 user = vpxuser] VMotionPrepare: dstMgmtIp = 2620:91:0:96:73
Tags: VMware
Similar Questions
-
Use an existing drive - failed with the General system error
Hello
I have a 5.0 esx host. as soon as I created a virtual machine and installed an operating system.
Now, I want to have another exact copy of this virtual machine.
what I've done is therefore:
- copied hard and flat-vmdk vm1 files in another data store.
- in the Wizard "Select a disk" has created a new vm2 and chose to use the existing virtual drive (chose the path where I copied the vmdk files).
- When I try to turn on the vm2, it fails with "does not illuminate: General error has occurred."
What Miss me in the configuration.
Please note that I have so not vcenter server cannot use cloning option.
Thank you.
You will find may be easier to use the functionality to export the OVF template and deploy OVF model in the vSphere Client. Export the virtual computer off and when you deploy the same VM you can rename and choose the destination data store. The configuration will be supported and then you can customize just the required guest OS.
-
I cannot associate my signature to the creative cloud, an error occurs when the opening of the first, he is asking me to renew the subscription, what I do?
Hello
Please see CC help | 'Renew your membership' window appears when you launch an application Cloud Creative
Kind regards
Sheena
-
Cannot perform updates of Windows with 641 and 80070641 error codes
Original title: update problems
Get 641 and 80070641 errors every time I try to download updates. How to solve this problem?
Hi Bob,
Please follow the links:
Method 1:
I suggest to ignore the title and follow the steps as indicated in the article.
0x80000FFFF error code when you download updates on a computer running Windows Vista by using Windows Update or Microsoft Update
http://support.Microsoft.com/kb/946414
Warning: Important This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up the registry, click on the number below to view the article in the Microsoft Knowledge Base:
http://Windows.Microsoft.com/en-us/Windows-Vista/back-up-the-registry
Method 2:
Scan your computer by using the Microsoft Safety Scanner by clicking Download now, because this might have caused by viruses:
http://www.microsoftsafetyscanner.com/
Note: The data files that are infected must be cleaned only by removing the file completely, which means that there is a risk of data loss.
I hope this helps.
-
The drive stops at 1% with the platform-specific error 2338
Hello
I'm P2V a Windows 2003 server in my vCenter environment 5.1.
Using Converter Standalone version 5.1.0
All ports is open I firewalls, but still I get this error:
FAILED: An error occurred during conversion:
'Platform-specific error 2338'
I am attaching a logfile here, so if anyone can help to understand what causes the error, I understand that :)
When you select a host in a DRS cluster automated, it's the vCenter server who makes the decision what ESX host in the cluster to use. If it's a manual DRS or non - DRS cluster, you can select the specific host. The obvious difference of the user, is that in the latter case there is an extra drop-down box for the selection of the host.
In fact, it's some sort of bug in user experience, because this difference in behavior is not clear. The guide mentions on 49, but we know not to be cut.
Kind regards
Plamen
-
Hello
I'm setting up a clone on and 5U8 RHEL environment. When I run on the dbTier adcfgclone.pl, she went out with an error at 0%. Excerpts from the journals are as follows:
****************************************************
Profile Phase jump
Jump apply Phase
Complete RunAutoConfig...
StackTrace:
java.lang.Exception: RC-00128: error reading from file oraInst.loc
Asked by oracle.apps.ad.clone.util.OracleHomeCloner
at oracle.apps.ad.clone.util.OracleHomeCloner.getGlobalInventoryLocation(OracleHomeCloner.java:540)
at oracle.apps.ad.clone.ApplyDBTechStack.executeOUICLI(ApplyDBTechStack.java:1596)
to oracle.apps.ad.clone.ApplyDBTechStack. < init > (ApplyDBTechStack.java:462)
to oracle.apps.ad.clone.ApplyDBTier. < init > (ApplyDBTier.java:156)
at sun.reflect.NativeConstructorAccessorImpl.newInstance0 (Native Method)
at sun.reflect.NativeConstructorAccessorImpl.newInstance (unknown Source)
at sun.reflect.DelegatingConstructorAccessorImpl.newInstance (unknown Source)
the impossible (unknown Source)
at oracle.apps.ad.clone.util.CloneProcessor.run(CloneProcessor.java:68)
at java.lang.Thread.run (unknown Source)
You are looking for help, please guide
Thank you
I applied the Patch 9171650
-
Problem with HTML; Java script error occurred.
Hello
I was wondering if someone could help me put code in InDesign, I get an "encountered Javascript error". I tried two versions, old and new from google maps. It does not seem to make a difference.
" < iframe src =" https://www.google.com/maps/embed?pb=! 1m18!1m12!1m3!1d3385.2463441033283!2d115.85631100000 002!3d-31.954213000000003!2m3!1f0!2f0!3f0!3m2!1i1024!2i768!4f13.1!3m3!1m2!1s0x2a32bad5b744 7749% 3A0xe5fe8e1ce7fcb54e! 1% 2F140 2s + St + George + terrace! 5e0! 3 m 2! 1sen! 2sau! 4v1396304372112 "width ="800"height ="380"frameborder ="0"style =" border: 0 "> < / iframe > "
Appreciated
Moved to DPS because that's the only possible reason to use it.
Yes, it's a known issue. My personal solution is to use Bing Maps.
-
System error fatal 0x000012f Stop
Original title; Unrecoverable system error
I booted up my P Bell o/s Win Vista with vista recovery disc I got from Neosmart. Everything seemed to be simple sail and in the last minute that I get this blue screen with - check {fatal system error} known DLL 0x000012f failed to stop. system process finished in unexpected ways with the State of 0xc000012f (0x89d91690 0 x 000600000000). the system has been shut down. Please help...
Thank you
Hello
1. have you tried to recover Windows using a previous issue recovery disk?
2. which version of Windows Vista is installed on the computer?
3 have you tried to start the computer in safe mode?
4 did you a recent software or changes to the material on the computer?
Incompatible system files can also cause this error. I suggest you to check if the version installed on the computer and the recovery disc are the same.
My PC running the 32-bit version or 64-bit Windows?
http://Windows.Microsoft.com/en-us/Windows7/find-out-32-or-64-bit
I also suggest you go through the Microsoft Help article and check.
Pick up the pieces after a computer crash
http://Windows.Microsoft.com/en-us/Windows-Vista/picking-up-the-pieces-after-a-computer-crash
How to fix BlueScreen (STOP) errors that cause Windows Vista to shut down or restart unexpectedly
http://support.Microsoft.com/kb/958233
You can also check:
What are the system recovery options in Windows Vista?
Hope this helps and keep us posted.
-
Net 51 with a view system error
I have two boxes of Windows XP that I login as administrator account. I was able to synchronize files, map network drives and can do a tracert to reach one of them.However, when I perform a net view on, I get the following error
51 system error has occurred.
Windows cannot find the network path. Make sure the network path is correct and the destination computer is not busy or turned off the coast. If Windows still can't find the network path, contact your network administrator.
How to make this command work?
Hello
· Your computer is on a domain network?
Follow the steps in troubleshooting this article and check if that helps:
You cannot access shared files and folders or browse computers in the workgroup with Windows XP
http://support.Microsoft.com/kb/318030
See also this article that resembles the same error.
Error when you try to access shared resources on a computer that is running Windows 2000 or Windows Server 2003: "53 system error has occurred" or "51 system error has occurred."
-
I have several computers on a home network with WiFi and Ethernet access to a NAS network.
Using a batch file, card readers network at startup, etc.A for (I have 4) computers fails to map the network drive. All other computers work fine with the same batch file.Specifically, when the following command has been executed in the batch file:NET use * /d /yThe computer responded with:50 system error has occurred.The request is not supported.When the batch continues running and map network drives, each command mapping «net use z:...» ' produces the following:53 system error has occurred.The network path was not found.This particular computer in question is a laptop and all other software and functionality seems to work very well.It looks like a problem with Windows, but after some research, I found that many variations in Windows can produce the same above error codes.Help!Hi Roger,
Have you been able to solve the problem?
System Error Codes are very broad. Each of them can occur in one of hundreds of locations in the system. As a result, the descriptions of these codes cannot be very precise.
Please visit the following link to learn more about the system error 50:
System (0 to 499) error codes
http://msdn.Microsoft.com/en-us/library/ms681382(v=vs.85).aspxPlease let us know the status of the issue.
-
Compaq Mini CQ10 CNU00872CY: password check failure fatal system error stopped CNU00872CY
have the same problem on my hp mini.
password check failure fatal system error stopped CNU00872CY
Please helpme to slove this problemPlease enter = e9l11ux7ei
Kind regards
KNRK
I work for HP
-
Choose any server to synchronize the time with, it says, "an error occurred while Windows timed (insert.server.here) with," can someone please tell me why this is, or particularly how to solve this problem? I am trying to connect to NetFlix with Windows Media Center, and as you can probably guess, I'll have no chance. He told me, INVALID TIME SETTINGS. Your computer's clock is set for an hour and invalid date or is not correctly adjusted for daylight saving time. Update the settings of the clock, then try again. Even when I set the time manually it will not work. I just don't understand. Help, please!
Hello
How to fix synchronization of time Internet - add your own time server
http://www.edbott.com/weblog/?p=1779Dealing with Windows Vista time sync problems
http://www.howtogeek.com/HOWTO/Windows-Vista/dealing-with-Windows-Vista-time-sync-problems/Synchronize your clock with time servers Internet from the Vista command prompt
http://www.howtogeek.com/HOWTO/Windows-Vista/sync-your-clock-with-Internet-time-servers-from-the-Vista-command-prompt/Time synchronization on Windows XP and Vista with Internet
http://www.techexams.NET/blogs/jdmurray/synchronizing-the-time-on-Windows-XP-and-Vista-with-the-Internet/I hope this helps.
Rob - bicycle - Mark Twain said it is good. -
6 of Lightroom cannot read my Canon 5 d Mark III photo files, the import message I received: the following files were not imported because they could not be read. I use the same camera that I used Lightroom 5 with the same cards Compact flash. The files are: DK5A0243. CR2
Lightroom 6 trying to copy pictures to a different directory than what is Lightroom 5. That's why you have the problem.
You can change the directory where you are teaching LR 6 to place photos, or change the permissions on this directory to read & write.
-
How can I stop my computer with a blue screen coming up and crashing
Hello
my computer keeps crahing with a blue screan befor, I ran anti spy wear and its projection up to nothing. When it reboots it says. from what I can tell, it's the same thing all the time.
help please
Signature of the problem:
Problem event name: BlueScreen
The system version: 6.0.6001.2.1.0.768.3
Locale ID: 3081
More information about the problem:
BCCode: 50
BCP1: 9131EB99
BCP2: 00000001
BCP3: 886F7C45
BCP4: 00000000
OS version: 6_0_6001
Service Pack: 1_0
Product: 768_1
Files helping to describe the problem:
C:\Windows\Minidump\Mini080812-03.dmp
C:\Users\ricky g\AppData\Local\Temp\WER-440422-0.sysdata.xml
C:\Users\ricky g\AppData\Local\Temp\WER204C.tmp.version.txt
Read our privacy statement:
http://go.Microsoft.com/fwlink/?LinkId=50163&clcid=0x0409
Hello
Pick up the pieces after a computer breakdown - see what to do if Windows won't start correctly
http://Windows.Microsoft.com/en-us/Windows-Vista/picking-up-the-pieces-after-a-computer-crashTo BlueScreen troubleshooting methods using BlueScreenView and MyEventViewer
See my answers, if this thread - top 3 responses (+ 1 other).We can analyze the minidumps if you make them available at the SkyDrive or other
file sharing sites (such as MediaFire). If you have problems downloading the minidumps
Copy it to the desktop or Documents folder and download them from there.ZIP or download the content of the C:\Windows\minidump
Use SkyDrive to upload collected files
http://social.technet.Microsoft.com/forums/en-us/w7itproui/thread/4fc10639-02dB-4665-993a-08d865088d65-------------------------------------------------------------------------------------------------------------
BCCode: 50 0 x 00000050
References to Vista also apply to Windows 7.
Have you recently added any hardware? Have you updated any drivers just before these
has started? (Check control panel - updates of Windows to see if all drivers have been updated
all the time this started) guilty likely hand are video driver, other drivers,.
memory and antivirus/antispyware/security products could be at fault, but also in car
questions.Use the troubleshooter below and refer to the following message for pilots and memory
When you get these sections and then back to the resolution of the problems according to the needs.BCCode: 50 0 x 00000050
Cause
The BCCode 50 usually occurs after the installation of the defective material or in case
failure of the hardware installed (usually associated with a faulty RAM, either main memory,
Cache L2 RAM or video RAM memory).Another common cause is a defective system service installation.
Antivirus software can also trigger this error, as can a corrupted NTFS volume.
Solve the problem
Solve a defective hardware problem: If the material has been added to the system recently,
Remove to see if the error recurs. If existing hardware has failed, remove or replace
the defective component. You must run the diagnostics of material provided by the manufacturer of the system.
For more information about these procedures, see the manual of your computer.Fix a defective system service: Disable the service and confirm that this
resolves the error. If so, contact the manufacturer of the service on a possible system
Update. If the error occurs during the system startup, restart your computer, and press F8 to
character mode menu that displays the choice of operating system. As a result
Windows Advanced Options, select last good known Configuration option menu.
This option is most effective when a pilot or a service is added at a time.Solve a problem of antivirus software: Disable the program and confirm that this fixes
the error. If this is the case, contact the manufacturer of the program about a possible update.Fix a corrupted NTFS volume: Run Chkdsk /f /r to detect and repair disk
errors. You must reboot the system before the start of the analysis of disk on a system partition. If
the hard drive is SCSI, check for problems between the SCSI controller and the disk.Finally, check the system log in Event Viewer for additional error messages that might help
identify the device or driver that generated the error. Disable the cache in memory of the BIOS
could also resolve it.
BCCode: 50 0 x 00000050<-- read="" this="">-->
* 1095.html? order = votes http://www.faultwire.com/solutions-fatal_error/page-fault-in-NONPAGED-Area-0x00000050--------------------------------------------------------------------------
Look in the Event Viewer to see if something is reported on those.
http://www.computerperformance.co.UK/Vista/vista_event_viewer.htmMyEventViewer - free - a simple alternative in the standard event viewer
Windows. TIP - Options - Advanced filter allows you to see a time rather
of the entire file.
http://www.NirSoft.NET/utils/my_event_viewer.htmlHere are a few ways to possibly fix the blue screen issue. If you could give the blue
Screen info that would help. Such as ITC and 4 others entered at the bottom left.
And other information such as codes STOP error and info such as IRQL_NOT_LESS_OR_EQUAL
or PAGE_FAULT_IN_NONPAGED_AREA and similar messages.As examples:
BCCode: 116
BCP1: 87BC9510
BCP2: 8C013D80
BCP3: 00000000
BCP4: 00000002or in this format:
Stop: 0 x 00000000 (oxoooooooo oxoooooooo oxoooooooo oxooooooooo)
Tcpip.sys - address blocking 0 x 0 00000000 000000000 DateStamp 0 x 000000000It is an excellent tool for displaying the blue screen error information
BlueScreenView scans all your minidump files created during ' blue screen of the.
http://www.NirSoft.NET/utils/blue_screen_view.html
death ' crashes and displays information about all accidents of a table.
FreeBlueScreens many are caused by drivers of old or damaged, in particular the video drivers
However, there are other causes.You can do mode if necessary safe or the Vista DVD command prompt or
Options recovery if your system is installed by the manufacturer.This tells you how to access the System Recovery Options and/or a Vista DVD
http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspxYou can try a system restore to a point before the problem started when one exists.
How to make a Vista system restore
http://www.Vistax64.com/tutorials/76905-System-Restore-how.html-------------------------------------------------------------------------
Start - type this into the search-> find COMMAND to top box and RIGHT CLICK-
RUN AS ADMINEnter this at the command prompt - sfc/scannow
How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe)
program generates in Windows Vista cbs.log
http://support.Microsoft.com/kb/928228The log can give you the answer if there is a corrupted driver. (Does not work
tell all possible driver issues).Also run CheckDisk, so we cannot exclude as much as possible of the corruption.
How to run the check disk at startup in Vista
http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html-------------------------------------------------------------------------
Often drivers up-to-date will help, usually video, sound, network card (NIC), WiFi, part 3
keyboard and mouse, as well as of other major device drivers.Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htmHow to install a device driver in Vista Device Manager
http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.htmlHow to disable automatic driver Installation in Windows Vista - drivers
http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx-------------------------------------------------------------------------
How to fix BlueScreen (STOP) errors that cause Windows Vista to shut down or restart
quit unexpectedly
http://support.Microsoft.com/kb/958233Troubleshooting, STOP error blue screen Vista
http://www.chicagotech.NET/Vista/vistabluescreen.htmUnderstanding and decoding BSOD (blue screen of death) Messages
http://www.Taranfx.com/blog/?p=692Windows - troubleshooting blue screen errors
http://KB.wisc.edu/page.php?id=7033-------------------------------------------------------------------------
In some cases, it may be necessary.
The Options or Vista recovery disk Startup Repair
How to do a startup repair
http://www.Vistax64.com/tutorials/91467-startup-repair.htmlThis tells you how to access the System Recovery Options and/or a Vista DVD
http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspxI hope this helps.
Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="">-><- mark="" twain="" said="" it="">->
-
I am trying to start my Dell Inspiron 1525, but get the following blue screen message "STOP: c000021a {fatal system error} the initial session of the process or system process ended unexpectedly with status 0 x 000000001 (0xc0000034 0x0010038c).» The system was stopped.
I tried to boot mode without fail & startup repair but nothing helps, always the message, any help would be really appreciated as all my College work is stored on the laptop.What about OttoWindows vista Home basicHello
Check with Dell Support, their online documentation, diagnosis and ask in the forums about known issues.
Dell support
http://support.Dell.com/Dell support drivers - product manual & warranty Info (left side) - and much more
http://support.Dell.com/support/index.aspx?c=us&l=en&s=DHSDell forums
http://en.community.Dell.com/forums/=========
STOP: 0XC000021A
Can be a difficult problem to solve, and you indeed need a technical help in a real store of the computer
(not the leeks and the glances at a BestBuy or other BigBox stores) or system manufacturer support.Cause
This error occurs when a subsystem of mode user, such as WinLogon or the Client Server Run-Time Subsystem (CSRSS), irremediably compromised and security can not be guaranteed. In response, the operating system goes into kernel mode. Microsoft Windows cannot run without WinLogon or CSRSS. Therefore, it is one of the rare cases where the failure of a user mode service can stop the system.
Incompatible system files can also cause this error. This can happen if you restored your hard disk from a backup. Some backup programs may skip restoring system files which they determine are in use.
Solve the problemRun the kernel debugger is not useful in this situation because the error occurred in a user mode process.
Resolve an error in the user-mode device driver or system, third-party application service: Because the bug 0xC000021A control occurs in a user mode process, the most common culprits are third-party applications. If the error occurred after the installation of the new or updated device driver or service system, third-party applications, the new software should be removed or disabled. Contact the manufacturer of the software on a possible update.
If the error occurs during the system startup, restart your computer, and then press F8 to character-based menu that displays the choice of operating system. In the Windows Advanced Options menu that results, select the last known good Configuration option. This option is most effective when a pilot or a service is added at a time. If the error is not resolved, try to manually remove the offending software. If the system partition is formatted with the (FAT) file allocation table, use a MS-DOS boot disk to access the hard disk of the computer. If the system partition is formatted with the NTFS file system, you may be able to use Safe Mode to rename or remove the defective software. If the defective software is used as part of the start-up procedure of the system Safe Mode, you must start the computer by using the Recovery Console to access the file. If a room newly installed if material is suspected, remove it to see if that fixes the problem.
Try running the emergency recovery disk (ERD) and allow the system to repair any errors that it detects.
Solve a problem of file system do not match: If you have recently restored your hard disk from a backup, check if there is an updated version of the backup/restore program available from the manufacturer. Make sure that the latest Windows Service Pack is installed.
STOP: 0XC000021A<-- read="" this="">-->
* 1314.html http://www.faultwire.com/solutions-fatal_error/Status-System-Process-terminated-0xC000021A------------------------------------------------------------------------
Look in the Event Viewer to see if something is reported on those.
http://www.computerperformance.co.UK/Vista/vista_event_viewer.htmMyEventViewer - free - a simple alternative in the standard Windows Event Viewer.
TIP - Options - Advanced filter allows you to see a period of time instead of the entire file.
http://www.NirSoft.NET/utils/my_event_viewer.html-------------------------------------------------------------------------
It's my generic bluescreen convenience store - you can try Mode safe mode as suggested in article
above - repeatedly press F8 that you start. Disks of Vista are probably necessary - if you do not have to try
repair, you can borrow a friends because they are not protected against copying. You can also buy the physical
discs of the machine system good cheap that you already own windows (you will need to reinstall
If necessary). You can also repair disks on another computer.Here are a few ways to possibly fix the blue screen issue. If you could give the blue screen
info that would help. Such as ITC and 4 others entered at the bottom left. And all others
error information such as codes of STOP and info like IRQL_NOT_LESS_OR_EQUAL or PAGE_FAULT_IN_NONPAGED_AREA and similar messages.As examples:
BCCode: 116
BCP1: 87BC9510
BCP2: 8C013D80
BCP3: 00000000
BCP4: 00000002or in this format:
Stop: 0 x 00000000 (oxoooooooo oxoooooooo oxoooooooo oxooooooooo)
Tcpip.sys - address blocking 0 x 0 00000000 000000000 DateStamp 0 x 000000000It is an excellent tool for displaying the blue screen error information
BlueScreenView scans all your minidump files created during "blue screen of death," collisions
Displays information on all the "crash" of a table - free
http://www.NirSoft.NET/utils/blue_screen_view.htmlBlueScreens many are caused by old or damaged, in particular the video drivers drivers however
There are other causes.You can do mode if necessary safe or the Vista DVD command prompt or
Options recovery if your system is installed by the manufacturer.How to start on the System Recovery Options in Windows 7
http://www.SevenForums.com/tutorials/668-system-recovery-options.htmlYou can try a system restore to a point before the problem started when one exists.
How to do a system restore in Windows 7
http://www.SevenForums.com/tutorials/700-system-restore.html-------------------------------------------------------------------------
Start - type this in the search box-> find COMMAND at the top and RIGHT CLICK – RUN AS ADMIN
Enter this at the command prompt - sfc/scannow
How to fix the system files of Windows 7 with the System File Checker
http://www.SevenForums.com/tutorials/1538-SFC-SCANNOW-Command-System-File-Checker.htmlHow to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
generates cbs.log Windows Vista (and Windows 7)
http://support.Microsoft.com/kb/928228The log can give you the answer if there is a corrupted driver. (Says not all possible
driver problems).Also run CheckDisk, so we cannot exclude as much as possible of the corruption.
How to run the check disk at startup in Windows 7
http://www.SevenForums.com/tutorials/433-disk-check.html-------------------------------------------------------------------------
Often drivers up-to-date will help, usually video, sound, network card (NIC), WiFi, part 3
keyboard and mouse, as well as of other major device drivers.Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htmInstallation and update of drivers under Windows 7 (updated drivers manually using the methods above
It is preferable to ensure that the latest drivers from the manufacturer of system and device manufacturers are located)
http://www.SevenForums.com/tutorials/43216-installing-updating-drivers-7-a.htmlHow to disable automatic driver Installation in Windows Vista - drivers
http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx-------------------------------------------------------------------------
How to fix BlueScreen (STOP) errors that cause Windows Vista to shut down or restart
quit unexpectedly
http://support.Microsoft.com/kb/958233Troubleshooting Vista Blue Screen, error of JUDGMENT (and Windows 7)
http://www.chicagotech.NET/Vista/vistabluescreen.htmUnderstanding and decoding BSOD (blue screen of death) Messages
http://www.Taranfx.com/blog/?p=692Windows - troubleshooting blue screen errors
http://KB.wisc.edu/page.php?id=7033-------------------------------------------------------------------------
In some cases, it may be necessary.
Startup Options recovery or Windows 7 disk repair
How to run a startup repair in Windows 7
http://www.SevenForums.com/tutorials/681-startup-repair.htmlHow to start on the System Recovery Options in Windows 7
http://www.SevenForums.com/tutorials/668-system-recovery-options.htmlHow to create a Windows 7 system repair disc
http://www.SevenForums.com/tutorials/2083-system-repair-disc-create.htmlI hope this helps.
Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="" -="" mark="" twain="" said="" it="">->
Maybe you are looking for
-
For the USB Hi-Speed and Licensing policy GPIB controller
Hello I wanted to confirm understanding licensing NI VISA. If I use the GPIB controller OR to the USB Hi-Speed, is NEITHER VISA license are included? 488.2 NOR pilot is that CD is included along so I guess its license. In accordance with the licensi
-
I need to reconfigure a printer LaserJet 2055dn network. However, I can't know how to do a cold reboot. The sequences ' press on and press and hold the power on ' do not seem to apply to the 2055dn and there is not a reset option in the menus. Any
-
MMDRIVER &#62; IMF XP
PILOT OF HIS MISTAKE MMDRIVER. IMF IS NOT IN THE OPERATING SYSTEM. Edit by G225: Am I on Windows for hardware and driver.
-
Hello I am trying to download a driver for a laserjet 5550dn printer. I go as far as the selection of the printer on the driver download page, then click on it and then I like that this page does not exist. I'm in Ireland, so I wonder which makes a d
-
Salve, knew a servre PowerEdge 2950 (tag 74MPW2J) con Controller PERC instalalti 6 brain sono da 146GByte. Di fabbrica sono configurati in RAID 5. Currently he system can not boot it.Due di questi (he 2 nd it 4) LEDs at fault. SE price 2 brain nuovi