Sansa View not recharge, but the battery becomes hot, no blue ring

Similar Questions

• (plugged in, load) but the battery is not charging

  Hello!

  I have a problem with my hp laptop Pavilion dv6 - 2190ev.

  The laptop cannot start if the charger is connected only (and the battery). It will only start if the battery is on. Also, the led and the laptop displays: (plugged in, load) but the battery won't charge!

  The battery and charger are ok, because I tried on another laptop and work there!

  So, the problem seems to be on the laptop. I also update the BIOS and the problem persists.

  Can someone help me solve this problem?

  Looks like you did a few good troubleshooting at this point.  One thing which is ofter overlooked in these questions is the motherboard.  Here is an article by HP, battery not power Notebook or hold a Charge.

  Please take a look.  There are suggestions for troubleshooting for the power supply, motherboard and battery, as well as links to other useful information. I'm sorry this isn't a simple solution, but you could just find very useful information in the article.

  Good luck with it,

• My laptop is plugged in, but the battery is not charging

  My system is win7 Ultimate, 32-bit operating system. My laptop is Toshiba Satellite - C600 - 02L, processor: Intel (r) Pentium (R) CPU, P600 1.87 GHz, 1.87 GHz... I bought it about a year and eight months ago.

  I noticed that the battery light is off. I checked the battery meter icon & he said the PC was plugged, but the battery was not in charge. In the Device Manager window, I found that a device was not working properly. The details of this device are:

  Device type: drivers Non Plug-and-Play

  Service name: MpKsl45a6e13d

  This device is not present, is not working properly or is not all its drivers installed. (Code 24).

  I don't know if this has nothing to do with the problem, but if so, what is the solution to this problem? Please help me solve this problem.

  Thank you.

  Hi Ronnie,.

  Thank you for your attention to this issue. Pls find below info from the battery.

  Battery: Battery information

  Rated capacity	48600
  Full last Charge	30272

  Concerning

  Hi Mustafa

  This information shows that your battery has 62% of the original capacity left. Even if it's a little weak, it is not at a critical point where the battery should be the cause of all the problems. The typical Li-ion battery will last for 1 to 3 years.

  I would recommend that you go to Toshiba Support forums and check to see if there is a utility to check the status of the material of the AC/charge circuit on this laptop. Here are a few links for your convenience.

  Toshiba support - home page:

  http://www.CSD.Toshiba.com/cgi-bin/TAIS/support/JSP/home.jsp

  Toshiba Support Forums:

  http://forums.Toshiba.com/

  Computer troubleshooting - Toshiba Forums: http://forums.toshiba.com/t5/Computer-Troubleshooting/ct-p/cat_troubleshoot

  Tell us what you find.

  Concerning

• Satellite A100 PSAA9C does not work without the battery inside

  I'm having a strange problem with a laptop Satellite A100 (PSAA9C-SK900E).

  The machine will not work without the battery in it. If the power supply is connected in the machine and the wall, it will power without the battery installed. If I install the battery, let it load completely (battery LED goes from orange to blue and the plug LED is blue) then start the machine it will work for a period of time (more than an hour depending on what I'm doing) then suddenly turns off.

  If I restart the machine, it will work for a very short period (sometimes only for a few minutes) just before going off.

  If I do this a couple times, the machine will be not even by post before turning off.
  If I let the machine to recharge, it runs for a while and then do the same thing after using it for a while.
  If the battery is pooched, which is fine with me. How to operate with only the power supply of the machine?

  As I type this I'm suspecting that the adapter cannot be taken out the required voltage/amperage. (adapter is not still hot when charging, are my other laptops) Any suggestions would be greatly appreciated.

  Thank you.

  Hello

  If I understand your assignment, the laptop does not power up without the battery
  But it will light if the battery is connected.

  The question is; Is the power led on if the AC adapter is plugged?
  If this isn't the case, then it means that the power adapter is faulty and so the laptop cannot be turned on by using only the AC adapter.

  I think you should test a new adapter. Maybe it helps!

• Battery plugged in but no load and battery life which is at 0%, but the battery is 89-90% charged.

  I have a laptop gateway that I bought last year.  It runs Windows Vista Premium (64-bit), and recently it has been send me load/battery indication problems.  The battery becomes a burden, but the battery monitor does not indicate correctly.  I watched it one day and it loaded up to 89-90% and then the battery monitor indicated 0% and not charging.  When I restart the laptop the charge indicates correctly around 89-90% and will show correctly when it is plugged in.  Once he reached 89-90% charge once again it comes back to life 0% battery and plugged in and not charging.  I tried the battery re - learn and when it reaches the level of 89% it stops and shows a surge of battery, but if you restart the pc it will state the cost of 89% and act normal.   I tried the procedure that I saw on this site earlier with the functioning of the battery all the way down and let the pc "die" on its own, but that still does not work.  Is there a problem with the software in the package of windows vista power control?  I saw at least another person having the same problem but have seen no response or resolution for this.  It is not the connection motherboard problem because the thing is load and works normally except when, if you try to load up once he reached that magic level, it indicates a 0% charge and plugged in and not charging.  I have signed up for a profile on this site and have been typing this message with remaining 0% battery Xantrex battery life reading.

  Question resides in the BIOS. I MD26 series laptop Gateway and has been facing the same problem.

  Download the latest BIOS for you series laptop, update your BIOS and you are done. I found the BIOS of my laptop to this place

  http://support.gateway.com/support/drivers/GetFile.asp?ID=24427&DSCR=gateway%20MD24%20and%20MD26%20BIOS%20Version%209A10h%20For%20Windows%20Vista&UID=290186182

  Hope that solves your problem.

  PS: Please download the BIOS that is related to your computer laptop model/series only. I am not responsible for any damage to your motherboard

  -Patricia

  I am what I am...

• C50-A-19 t satellite does not start with the battery mounted

  OK, first post here.

  I see similar questions coming, but as they are never QUITE the same, I am that posing in a new thread.

  I left my Satellite from one day to the next (do not remember if I had put off, or he simply had 'gone to sleep', but it has been connected to the grid).

  When I got to reboot, I got a power light on, but screen blank (black). After reading a few similar complaints on the internet (via another laptop!), I tried to remove the battery and power from the grid.
  This worked well (I write him in this state right now).

  But whenever I put the battery and try again, it will fail in the same way.
  I tried this company "press and hold power for 30 seconds" without success (but I'm not 100% sure of the EXACT procedure actions sequence).

  I have a few questions:

  (1) I take the laptop away from my office - is there a problem with everything just works like this (i.e. of the grid, with no battery inserted) indefinitely?

  (2) in any case, I want to solve the problem.
  If the battery has run COMPLETELY flat, and that the laptop can not it lights but also operate normally?

  Alternatively, is probably that the battery has not experienced a catastrophic failure and simply needs to replace?
  If so, I'll just buy a. BUT...

  What I don't want to do, is to pay for a costly spare battery, to find that it was actually another factor at the origin of the problem, and I'm back to square one and out of Pocket!

  Any advice would be welcome.

  Thank you

  Mike

  Hello

  According to your assignment, in most cases, you use the laptop connected to the power adapter but no battery. Is this correct?

  First we need to know that if the AC adapter is plugged in, the laptop should work correctly with - and without inserting the battery.
  If you unplug the AC adapter, the laptop should automatically switch to battery power. In this case, it is important that the battery is pretty cool power to provide the power for the laptop.
  In case the battery is empty, the laptop will not light.

  I recommend to insert the battery plug the power adapter and charge the battery for a longer period of time.

  You should also check if the battery is recognized by the Windows system and the battery charge indicator (battery in the taskbar icon) shows the State of battery charge.

  In case the battery is fully charged and the laptop does not work using the battery power only, you should test the new battery.
  If new battery does not solve the problem, s for laptop hardware needs an audit.

• AC adapter does not work if the battery is not removed on my Satellite?

  A few days as my Satellite does not use electricity from the adapter: he wants to only use the battery (so after a few hours, it stops).

  Connect and disconnect the power supply when the notebook is on or before restarting, it doesn't change anything (if the battery is always in its place). The power adapter, cable spines,... seems in good conditions and I don't think they have problems because when I remove the battery and restart the laptop, the Satellite finally understands that he must use the power supply and not the battery. Then I can put the battery back in its place and load it... But if I unplug the AC adapter, the circus re - start.

  Is power off somewhere? Is there a place where you can choose: "always use the battery and not the power?

  I don't think so, it's a motherboard problem?

  Hello

  It is not easy to say why it happens. For me, this looks like an electronic malfunction of power supply.
  But it's only my suggestion to be 100% sure that some diagnostic tests are necessary.
  But the battery is ok and AC adapter works as well as you suggested.
  What you can do is to check your BIOS version and compare it with the BIOS that is available on the page. Is there a newer version, so you can try to update.
  Note: Be careful! Bad BIOS and update wrong procedure can damage the laptop.

  But if you use the latest BIOS, so I think it must be a hardware malfunction. In this case, the only way to find the bug is to ask the AEP from Toshiba in your country for help.

• Laptop will not start without the battery attached

  Hello

  I have a Hp pavilion dv6700 series (dv6840el) and just, it will not start without the battery attached.

  If I plug in the AC adapter, I get some computer activity (fan, noise of the dvd player and HD drive spins) for about 5 seconds, then shuts down.

  Once I plug the battery (which is dying, who need a replacement), the laptop starts fine.

  So my question is: what is a motherboard or a problem with the AC adapter?

  The AC adapter looks ok, however. But if I am considering buying a spare battery, I assure you that I have a new adapter as well.

  Thanks in advance.

  Hello

  Visit this link

  http://h10025.www1.HP.com/ewfrf/WC/documentSubCategory?tmp_rule=61317&tmp_task=solveCategory&CC=US&DLC=en&lang=en&LC=en&Product=5081068&Query=dv7-6052ea&Tool=

  Good Luk

• I just bought my hp pc Pavilion g series, but many times not dΘmarre; the screen remains black or blue and must strive to market several times. What is going on?

  When I turn off my pc and that you want to turn it back on, it does not work and the screen remains black or blue, sometimes but nothing else and does not

  starts up, until I have try several times in pushing and disable the power button and suddenly starts working again. The pc is almost brand new (2 weeks)

  What is going on?  Thank you very much

  Hello

  I suggest you do the repair of the system startup and check if that helps resolve the issue.

  Check the link for more information on repair system below.

  Startup Repair

  http://Windows.Microsoft.com/en-us/Windows7/products/features/Startup-Repair

  You can also check the event viewer for more information on the error message.

  Open event viewer

  http://Windows.Microsoft.com/en-us/Windows7/open-Event-Viewer

  See also:

  Resolve stop (blue screen) errors
  http://Windows.Microsoft.com/en-us/Windows7/resolving-stop-blue-screen-errors-in-Windows-7

• Brand new laptop dies completely stopped for 2 days, but the battery lasts 5 hours if the accused

  Hi guys, my brand new Acer E 15 dies completely if I did not put on for 2 days, but the battery lasts 5 hours so I load it.

  If you stop the way you do that, when you start it you see the Acer screen at startup until it starts to load windows? Go to Options to food and on the left, click on choose what the key power and closing the lid is set to make.

  If it is in hibernation, chane button close and cover for sleep.

  Hibernation can cause big problems.

• View not strong in the photoshop "print format" cc on pc

  View not strong in the "print size", but ok to any other magnification. Photoshop on PC cc

  You have to realize what you watching a smarting down image is not your pixels of images.  Your screen most likely also has a low resolution the you must print you print different pixels there are more pixels, and they will be a higher resolution than the screen pixels. You need to do a test print to see how well sharpened, the image printed on the print size.  View all print's size display am image the size of the printing will be.  If you have set your preferences Photoshop display to the screen resolution resolution has. If you have several screens and they have a different resolution that you must have the image on the screen that matches the resolution of the screen, you set in your Photoshop preferences for the display resolution. If you do not set the correct resolution that post you a Photoshop will scale your image to a different size than the print size.

  

• When I use my clipping on an image mask, fills the form I use the whole layer instead of just being a small shape Panel and then I put my picture on the shape layer, a clipping mask, but the form becomes clear with just a slight edge. The photo behind

  When I use my clipping on an image mask, fills the form I use the whole layer instead of just being a small shape Panel and then I put my picture on the shape layer, a clipping mask, but the form becomes clear with just a slight edge. The photo behind it does not move. I did this project of class before and it worked fine so I'm not sure if I have something started or... Any thoughts?

  I thought about it. That's all just stupid on my part and a bit of frustration because photoshop is my sworn enemy of then adobe added in. Thanks tho!

• RH9: graphics are not displayed, but the fact of the anchored frame

  TCS3/FM10/RH9

  I'm a link FM books to my HR project.  With the help of FrameSLT, conditionalized my graphics (contained in an anchored frame) on FM so that they are not displayed.  It works very well on FM: there is no image and no image is anchored.

  However, in the draft HR charts are displayed with sharps; they appear also with sharps in the preview.  It's the way that it used to be in RH7. In FlashHelp, the graphics do not appear but the anchored frame is left behind, so I have a large white space where the graphic should be.

  I thought that there was a way that you don't have graphics in the project in the first place.  View the graphics in the project really slows down the update and generate processes. Why is HR still collect them if the graphic and anchored framework do not appear in the book of FM?

  Thanks in advance.

  It is about the other 'branch' Settings Conversion settings. The field is called 'Apply FrameMaker building conditional Expression' - check a blog by Matt Sullivan on Roundpeg on its use (http://blogs.roundpeg.com/2010/06/tcs-tips-for-conditional-text/) post

• V14 said that my droid2global is not compatible, but the beta installs fine, how is the official download installs?

  V14 said that my droid2global is not compatible, but the beta installs fine, how is the official download installs?

  I can see and download it now from the game of Google. crocadileut can you check again?

• Im getting the message 1% available (pluged, do not load) on the battery indicator

  Im getting the message 1% available (pluged, do not load) on the battery indicator

  Hi MICHAELRIVERA,

  ·         Who is the manufacturer of the laptop?

  ·         What operating system do you use?

  If your laptop does not charge:

  a. This may be caused by a faulty adapter (the part that you plug into the wall socket)

  (b) a component on the motherboard defective charger.

  Try the following.

  I suggest checking the connections, connect it properly, or contact the manufacturer. If you have a spare power adapter only to login and check. (Of the same brand and model)

  a. Click Start and type device in the search for field, and then select Device Manager.

  b. expand the batteries category.

  c. under the batteries category, right-click in the list of Microsoft ACPI compatible with battery control method and choose uninstall.

  WARNING: Do not remove the Microsoft AC adapter driver or any other compatible ACPI driver.

  d. on the Device Manager, select Action, and then search for the hardware changes.