Satellite A100-570 not start - error PXE

Similar Questions

• Satellite C650 does not start - error PXE - M0F

  Just bought a Satellite C650, get it home and my son decided to stop the whole upward as he ran.

  Now, we get the error below:

  Check the connection of the cable!
  PXE - M0F: Exit Intel PXE ROM
  No boot device - insert boot disk and press any key.

  We received no drives, nor a manual with adequate instructions and can't find anything on the web for help.
  Toshiba closes for the day.

  Hoping that this forum could give me an idea.

  Hello

  PXE error is displayed because the laptop has attempted to boot from LAN.
  Why it does not start from the HARD drive but LAN switches?
  I think the HARD drive is defect.
  Perhaps its also not recognized in BIOS.

  Switch on and press F2. This allows you to access the BIOS where you could check if the HARD drive is recognized. I guess it must be mentioned on the first page.
  If it s not there, then it means that the HARD drive is dead and must be replaced.

  I assume that the warranty is still valid; Therefore, you should get in touch with Toshiba ASP in your country for replacement.

• Satellite A100 will not start

  Hello

  I have a Toshiba Satellite A100-151, which does not start.

  A batery 11 times blink when I press the a/c power and nothing happens.
  Before that, I pressed too many keys f1 - f12 because it has stopped responding and a blue screen (memory error in the kernel) appeared.

  I tried:
  out/HDD, memory slot, battery and tried also reset with the AC button pressed without the battery.
  Thanks in advance for any helpful advice.

  Best regards

  As you know on this virtual path is not easy to say what the problem is here, but after reading your ad, I think there must be a problem with electronic control gear. It is placed on the motherboard.

  Problem is that work around is quite limited and I can see what you have already tried all the logical steps to check if computer laptop will be able to start on a path.

  I'm afraid it is worth noting that you can do except to communicate with the service of Toshiba and ask help from m.

• Satellite A100: Does not start a recovery DVDs

  Hi guys.
  First timer here.
  I have read some of the Q & A on reboot problems the A100 since the recovery DVDs.
  It seems I have the same problems as keith.

  I want to start all over again the OS and my laptop does not start from the DVD.
  Tried the standard f12 boot from cd option. tried her "hold C on the boot option.
  Both options end with no joy.

  The screen that says "loading ramdisk image", loads the machine breaks, asks me to wait, then every time the same thing.
  The screen goes black, flashes very quickly and white and then loads from the hard disk as normal.

  Now try to hold my frustration and do something radical.
  I know that in the Q & A previous, the subject is considered as replied...
  other options?

  My following thoughts are to delete/uninstall almost every thing and try and force the thing to boot from the DVD.
  have also copied the dvd and tried to boot from the copy, always with no joy.

  Are there any other suggestions?

  Is it possible to put a partition in the existing drive and start the recovery dvd in there, then delete the junk of the original section of the drive, and then delete the partition?

  is it possible to close all essential processes and format the HARD drive?

  is it possible to reset the HARD drive somehow?

  see you soon,
  Martin

  Hello Martin

  To be honest, it's pretty strange question. There is one thing I am interesting for:
  Is - this first time, you try to use a recovery media for the installation of the OS?

  If possible, try to get the Microsoft CD/DVD facilities to see if the same thing will happen.

  In any case, I will try to give you answers to your questions.
  > Is it possible to put a partition in the existing drive and to start the recovery dvd in there, then delete the junk of the original section of the drive, and then delete the partition?
  It will not work. On the recovery of the media it is recovery image and this image must be installed correctly. You cannot "recover DVD in there. Not question

  > is it possible to close all essential processes and format the HARD drive?
  I would like to know what you understand under the 'essential processes?

  > Is it possible to reset the HARD drive somehow?
  You can't do this somehow. If you want to 'reset' HARD drive, you must delete the existing partition or delete any OS installation. After having done that, you need to install new OS. All this will be done at the beginning of the recovery procedure.

  I really don't understand what's wrong there. Please answer to my first question, and we will continue this discussion. ;)

• Satellite A100 does not start - no action

  Hello

  I have a Toshiba Satellite A100, which does nothing. He went flat when he was asleep, and a few minutes later I plugged it and when I press the power button / nothing happens. I do not show that the battery recharges in illuminating the charging light. The power button does not illuminate.

  If I hold the power button for a long period of time, a few lights.
  The caps lock light. Light under F10 and F11 and wireless internet light keeps coming back even if it is disabled.
  Battery light comes on a few times, but it is wider than on.

  My thoughts are that power don't is not computer (I think than lights that come on are those who come usually on after you press the power button) I'll try and the hand to get on another charger to try but snacks that don't work there at - it suggestions?

  DESPERATE isn't my computer!
  CJ15

  Hmm can be a motherboard problem.

  Try reinstalling the memory and battery and see how it goes. If not, send it to an ASP for a quote.

• Satellite A100 does not start after the BIOS update

  Hello

  I downloaded the update to the bios toshiba A100 PSAA8 on the toshiba site and applied using the procedure of updating the bios from windows XP MSE. Restart after the start of the update stopped at the toshiba start screen.

  At startup the screen by pressing ESC watch text mode. The message indicated it confirms the update of the bios version. POST messages are:

  _________________________
  Genuine Intel CPU
  No TPM or TPM has problem
  1015 M system RAM passed

  Press to enter in SETUP
  _________________________

  Pressing F2 just clears the last message in line and then no change is found.

  The laptop comes with windows XP media center edition. I don't know why the TPM secure is enabled. It is possible that toshiba is available with the module of TPM enabled in bios updates that logbook. If this is the case, they must clearly identified as 'not applicable' upgrade for machines that are not relevant.

  I found similar messages around the forum without convincing answer.

  Is it possible to fix this without sending? Even if it turns out to be affordable, it make much sense to pay for the problems caused by toshiba.

  Hello

  Please don t blame someone for you mistakes ;)
  As far as I know that only a few sets of laptops come with TPM.
  If you want to do an update of the BIOS on the models at TPM, you will need to contact the ASP!

  Looks like you used a bad BIOS or bad BIOS update procedure.

  The Toshiba page a BISO update the documentation that describes how to upgrade the BIOS on each series laptop!
  You will find on the page of the Toshiba driver compatible BIOS and information over a large number of details!

  > Is it possible to fix this without sending
  Don t think so, and therefore, you will need to contact the Asp help!

  Good luck

• Satellite A100 does not start after the wrong Bios Update

  Yesterday, I upgraded my BIOS of 1.90 to 2.20 for VISTA... now, apparently, I downloaded the BIOS bad a100 to my A100 (PAAS...)

  Now the computer turn on (no display) then a few seconds later stops offshore and turns on again (without interruption), I am under warranty (and the computer is in the store) but I was wondering what to do if Toshiba is not honor the warranty?

  Thank you very much for your help!

  Hello

  I'm sorry to say, but it seems that you don't have the choice.
  You can ask him authorized partner in your country for the help that I know, BIOS update errors are not covered by a warranty and you will have to pay a small fee for fixing.

  In the worst cases, the motherboard must be replaced:(mais peut-être avez_vous une évasion chanceuse et seulement la puce ROM doit être flashée à nouveau)

• Satellite A100-570 slow downs the wide connection band

  I have a laptop Satellite A100-570. I bought this in July antiques.

  Just open the laptop, not even connect to the internet it manages reduce my speed on broadband.
  I know this because I'm doing a test of speed before and after the opening of the laptop using my PC.

  Computer laptop & PC are not yet in the same room!
  The wireless network connection is disabled, disabled 1394 connection and only LAN OK.
  (I use a BT Homehub, connected to my PC).

  My question is: how a laptop computer that is not on the internet brings to BB speeds.
  the laptop is o.k. otherwise.

  Any help appreciated.

  To be honest, the whole story is a little understandable and strange for me.
  Your laptop is connected to the router with a LAN cable or what?

  Sorry but I don't quite understand you. What is the speed with and without a cell phone?

  By the way: did you clean install of the OS before you start using this laptop?

• Satellite A100-570: need Driver for ATI Xpress 200 M graphics card

  Hello

  Could someone tell me where I can find the driver for my advice on video ATI card in Vista Edition Home Premium - 32 bit?

  is the name of the device: RADEON XPRESS 200 M Series (Microsoft Corporation - WDDM)
  Hardware ID is:
  PCI\VEN_1002 & DEV_5A62 & SUBSYS_FF101179 & REV_00
  PCI\VEN_1002 & DEV_5A62 & SUBSYS_FF101179
  PCI\VEN_1002 & DEV_5A62 & CC_030000
  PCI\VEN_1002 & DEV_5A62 & CC_0300

  INF section is:
  ati2mtag_RC410M

  Currently, only the ATI V7.14.10.8333 from Microsoft update driver can be used.
  It is using inf section:
  'RADEON XPRESS 200 M Series (Microsoft Corporation - WDDM)' = ati2mtag_RC410MB, PCI\VEN_1002 & DEV_5A62 & SUBSYS_FF031179

  I tried to download the '7-4_vista32_dd_ccc_enu_44985' of ATI driver, it does not recognize the video card. I check the INF file, it does not contain the inf section: ati2mtag_RC410MB. To install the ATI card manager does not recognize the video card and shows: no corresponding material found.

  my laptop is Toshiba A100-570. I also checked the Web from Toshiba site and tried the 'display-vista-8311003206112' driver, not worked not too.
  He said the installation of the driver failed. but no other info showed.

  so I hope that there is something updated from 7.4 to Vista driver capable of recognizing my video card.

  A big thank you to you.

  Hello

  It s very strange. Usually, the graphics driver ATI Toshiba for Vista should work!
  Satellite A100-570 belongs to the series of PSAA2.
  If you always choose this series on the download page of Toshiba if you want to use the drivers of Tosh!

  I checked the download page and it seems that this package contains the software of the chipset ATI UMA and the display driver.
  Maybe something was wrong during the installation process

  The last possibility might be the manual installation of the graphics driver.
  You can download this package and then you could install the driver through the Device Manager.
  You must manually assign to the source of the driver!

  It's worth a try

• Satellite A110 - does not start

  Satellite A110 does not start on power, but the HD load no start fan display running, but in a few seconds it stops.

  Help, please

  Hi jinskywalker,

  No display?
  No beeping?
  Nothing?

  In this case, you should read this article:
  [What steps must be followed if your Toshiba laptop does not start? | http://forums.computers.toshiba-europe.com/forums/ann.jspa?annID=21]

• Satellite C650 does not start with android phone on

  Hello

  I have a smallproblem. My Satellite C650 does not start when my android phone is plugged into the USB port. It sticks to the Toshiba start screen. I checked the boot order and the hard drive is the first on the list, so it isn't that. Any advice will be welcome.

  Thank you very much
  Ian

  Cool. Thanks for the comments.

• Satellite P300 does not start immediately

  Hello

  My Satellite P300 does not start immediately. I have to press the button start ca. 20 or 30 times.

  No results?

  Hello

  I have the Satellite Pro P300 in front of me. I use it almost 4 weeks now and I press the Start button, very gently and keep it down to the second or two and laptop starts fine everytime I want to start it.

  Do not press the button quickly several times but slowly and keep it down for a second or two.

• Satellite A100 - will not charge the battery

  Hello

  I have ned to help. My Satellite A100 will not charge the battery. He works the power adaptor for the led indicates charging status, battery shows 1% of loading tatus information, but none does change - no loading any time. When disconnected everything just stops off like normal desktop.

  I've already put battery in and out, made upgrades to the antivir software, makes Toshiba controls, tests, but what ever he did did not any change. If there is no way for restoration of battery how to check what the problem is I have no second battery or AC I can always buy new batttery but I don't know if the old one is broken and weather new would work properly?

  Best regards
  pawelg

  Hi pawelg,

  I agree with the user above. The battery can be charged only up to 500 times, and after that, it must be replaced. I think it's the case now, I mean that everything works correctly on the AC adapter so I think that the battery must be the reason for this.

  By the way: you can buy a new battery to an authorized service provider. ;)

• Vista: The device can not start (error Code 10) for a USB CDC device which works fine in XP

  I have a USB device 2.0 DCC which works very well under all of our Windows XP machines, but not based on Vista.  The device uses the usbser.sys driver and emulation of the virtual Comm Port.

  The text of the listing shows the same information on Xp and Vista, except under vista it shows no open pipes.  Shows Device Manager: device can not start (error Code 10).

  Using Vista I can't connect to the vista of CDC through concentrators or device to any other device wireless hub except for a Dlink Wireless hub, which has a layer of software between the CDC device and the PC.  With Xp, it all works very well on more than one PC, with Vista, there are questions.  I use the INF manufacturer provided for Vista, still no results.

  Any ideas on this would be greatly appreciated.

  Hi NuWaveDC,

  Thank you for taking the time to post on the Microsoft answers Forums.

  Please see the following article for an explanation of this error code 10.

  Explanation of error codes generated by Device Manager

  http://support.Microsoft.com/kb/310123

  Follow the steps listed for the error Code 10 see if this helps solve your problem or not.

  Please post back to let us know if this information was useful or not, so that we can help you if need be.

  Robyn
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• BITS can not start (error 80246008), tried to solve it, received error 1079, please help.

  Hello

  I tried to update my windows service, but the BITS can not start (error 80246008). I tried to solve it using the suggested steps, however, got an error 1079 (account specified for this service is different from the account specified for other services running in the same process). I use Windows Vista Home premium version 6.0. Third-party antivirus software, I don't have online protection of Rogers. For the record, I'm not a technical person at all. Any help will be appreciated. Thanks in advance!

  I tried to solve it using the steps suggested,

  It's what you tried, if not, please do it might help

  See if anything here helps.

  Error 1079: the account specified for this service is different from the account specified for other services running in the same process

  If you receive this error message, follow these steps:

  1. Click Start, click Run, type services.mscand click OK

  2. double-click on Background Intelligent Transfer Service.

  3. click on the tab to open a session.

  4. click Local System account and then click OK.

  5. right click on Background Intelligent Transfer Service and then click Start.

  0 x 80246008 WU_E_DM_FAILTOCONNECTTOBITS A download manager operation failed

  because the download manager could not connect the smart Background

  Transfer Service (BITS).

  http://support.Microsoft.com/?kbid=910337>

  You receive an error message when you try to download updates from the

  Windows Update Web site or the Microsoft Update Web site, or when you

  try to start the Background Intelligent Transfer Service 0 x 80246008

  http://support.Microsoft.com/kb/916251>

  An update is available to resolve a Service outage of Intelligent Transfer (BITS) background on a Windows Vista-based computer

  http://support.Microsoft.com/kb/940520

  13:06:42 UTC 08/26/11