Satellite A100-692: upgrade of the disk and issue stop Wlan

Similar Questions

• Satellite A100-033: I disabled the touchpad and now Fn + F9 won't allow

  I have a Toshiba Satellite A100-033 running Vista Home Basic. I use especially the laptop as a desktop replacement, and I do not like use the touchpad I disabled it, and instead, I use an external mouse via a USB port.

  I don't know if I disabled the touch pad by pressing Fn + F9 or by any other means (if it was by some other means that I forgot what it was). Recently, I wanted to re-enable the touchpad so that I could use the laptop outside the home. However, I found that by pressing Fn and F9 don't re - not allow the touchpad and I now can't use the touch pad at all.

  If I go into the properties of the mouse (in Control Panel), that tells me that my synaptics pointing device is enabled. If I go into Device Manager and look at 'mouse', I thought that my touchpad works properly.

  All this makes me suspect that the problem is not a hardware failure, but I changed a few settings, so that my touchpad is permanently disabled until I change the setting back to its original state.

  Help!

  Hello

  One of the solutions would be a system restore you could try to set the operating system to the point of time at the beginning. Perhaps that would help reactivate the touchpad.

  Conversely, you can try to reinstall the drivers for the Touchpad firstly I would recommend removing it from the Device Manager and then after restarting, you can try reinstalling the drivers downloaded!

  I would appreciate any comments from you

  Good bye

• Satellite A100-906: Question on the processor and HARD drive temperature

  Hey guys,.

  I want to ask u for the level of normal temperature of this laptop? I want to know the temperature of the CPU (1,2) and the temperature of the HARD drive, because I think that my laptop is overheating and it is a problem for me :/ (my temperature is now around 50 for the 2 hearts and nearly 40 for hard disk) Is this ok or? Ty ;)

  Hello

  Believe me, the 50 degrees C for the CPU and C 40 degrees for the disk HARD is a normal temperature! It's rare!
  On my laptop the CPU temperature increases up to 60 degrees C if no application works.

  But be aware that the temperature varies.
  If you run different applications on the laptop, the performance of the processor will be increased and the temperature rises.
  That is a fact.

  There is nothing wrong GUY ;)

• Satellite A100 - 692 PSAA9E: what is the max memory

  Can someone tell me how I can put in my book "A100-692 PSAA9E" memory?

  On the Internet there are pages which provide that 4 GB is the maximum amount of memory, whereas the manual says that 2 GB is max amount (the manual seems to be made for a group of individual booklets and also indicates
  my laptop should have a GForce but there a GFX ATI card).

  If 4 GB is the maximum amount, can I go with the memory following constellation? :

  2GB Stick Port 1
  512 MB key Port 2

  Also can I use Ram DDR2 - 667 Mhz instead of 533 Mhz Ram and or a mixture thereof?

  Concerning

  R4DIUM

  This chipset is the Satellite A100-692 supports?
  If it s a Mobile Intel 945 Express Chipset PM then it would support the 4 GB of RAM

  Here the details on the Intel page;
  [Intel 945 PM Chipset Express | http://www.intel.com/products/notebook/chipsets/945pm/945pm-overview.htm]

  But the fact is that there are different laptop A100 with different hardware specifications and so there is different information about the possible RAM Upgrade.

  However, I think that you will not be able to use the full 4 GB of RAM due to Win 32 bit limitations. The 32-bit OS can use max 3.2 GB

  Best regards

• Satellite 2140CDS: message: "insert the disk and press a key".

  Hello

  I got this laptop but the necessary update. I tried to put a master drive from my other laptop to update and it came with 'error' and now when I turned it back on it does nothing about it, totally blank and rpet "insert the disk and press a key".

  I've got everything I can think but still can not do anything.

  Please can someone help?

  Hello

  What do you mean with master drive? Do you mean the Toshiba Recovery CD or what?

  It seems that the laptop can not find a source of seed and so this message appears on the screen!

  If you use a FDD drive please check if the disk has been removed.

  You must simply insert your Toshiba Recovery CD and boot from the CD/DVD drive. That's all.

  PS: Check if the HARD drive isn't too bad, as if the internal HARD drive is malfunctioning you will not be able to reinstall the OS from the CD

• Satellite A100 - will not charge the battery

  Hello

  I have ned to help. My Satellite A100 will not charge the battery. He works the power adaptor for the led indicates charging status, battery shows 1% of loading tatus information, but none does change - no loading any time. When disconnected everything just stops off like normal desktop.

  I've already put battery in and out, made upgrades to the antivir software, makes Toshiba controls, tests, but what ever he did did not any change. If there is no way for restoration of battery how to check what the problem is I have no second battery or AC I can always buy new batttery but I don't know if the old one is broken and weather new would work properly?

  Best regards
  pawelg

  Hi pawelg,

  I agree with the user above. The battery can be charged only up to 500 times, and after that, it must be replaced. I think it's the case now, I mean that everything works correctly on the AC adapter so I think that the battery must be the reason for this.

  By the way: you can buy a new battery to an authorized service provider. ;)

• Re: Satellite A100 - RAM upgrade

  I'm looking at upgrading the Ram PC following Toshiba laptop: TOSHIBA Satellite A100 PSAA0C-LE400E

  The RAM I can upgrade is as follows:
  Memory slots / Max: 2 slots of RAM - bottom of the unit (available to the user), busy one with 512 MB DDR2 PC2-4200; can be filled with 128 MB, 256 MB, 512 MB, or 1 GB DDR2 (2048 MB = 1024 x 1 + 1024 MB x 1 MB Max)

  Memory: 512 MB PC2 - 4200 DDR2
  Running under windows 7 32 bit

  My Question is that I found Ram named series SQ G.SKILL DDR2 533 MHz (PC2-4200) 2GB SODIMM Memory (F2-4200CL4S-2GBSQ)
  Where can I put in 4 GB of ram instead of 2 GB max as shown above.

  I would say that if it fits it and works it should be able to use up to 3 GB of it with a 32-bit operating system but someone tried?

  Hey,.

  If the so-called specifications that you can use 1 GB in each slot and a maximum capacity of 2 GB RAM, why do you buy 4 GB of RAM?
  In addition on a 32-bit operating system you can use only up to 3.2 GB

  In your case, I would like to purchase 2 modules of RAM with 1 GB of capacity, and it works.

  I can recommend the modules of RAM Kingston, because they are quality products and never had a problem with them.

• Satellite A100-692: after an error of installation of Windows XP Prof blue

  Hello

  I bought a new satellite A100-692 with Windows XP Home OEM as an operating system.
  But when I tried to access the internet using the local area network and a Proxy Server, it does not work.

  I tried everything I knew and even ask some Forums to get a response, but nothing help.
  Then I think it can work when I install Windows XP Prof instead of the OEM Version. Because all Clients in our network work fine with it.

  But when I run the Installer (booting from CD) I get a blue screen with the message that there is a problem with the PCI (pci.sys) driver (after loading all the drivers).

  Can someone tell what I need to do so that I can install another OS?

  Thank you

  PS: Excuse me if my English is not very good ;)

  Hello

  First of all, the blue screen error message may appear due to hardware failure or serious malfunction of software.
  In your case I guess that it s a software issue because on the version OEM pre-installed, everything worked properly.

  In addition I checked the site s driver and it seems that there are drivers for 3 different notebooks to A100. In this case, you should be sure that you use the correct drivers.
  As far as I checked this laptop your A100-692 has PSAA9E number.

  But have you created a CD of drivers & tools before formatting the HARD drive? This option you will find in the assistance of Toshiba.

  However, you can download the drivers from the Toshiba site and here it is very important that these drivers will be installed in the right order!
  The chipset utility must be installed in a first time after all installations of service packs.
  The common modules are also important.

• Satellite A100-692 - how to reduce graphic memory?

  Hello!
  I'm looking for information how to reduce graphic memory. I have Satellite A100-692, PSAA9E-09900QGR and install 1024Mo RAM but 512 MB is dedicated to graphics memory. Because of this I have 512 MB of RAM in real-time only.
  I would change it. Should be spend of only 256 MB memory graphics. I checked the BIOS (ver. 2.00) and graphic drivers and anywhere is option for memory graphic change.

  Please help how do.

  Hello

  You described your situation, but this seems very strange.
  As far as I know, the laptop uses a 128 MB ATI MOBILITY RADEON X 1400 graphics card and this isn't a memory sheared graphics card!
  This card uses own 128 MB and must share main memory!

  I put t know why you suggested that you have only 512 MB.
  How did you test it?

• I'm upgrading of hard disks and need to reinstall my windows 7 Home premium

  I'm upgrading of hard disks and need to reinstall my windows 7 Home premium, however the laptop I bought did not include an installation disc, which I was aware of, and now I'm not sure if the recovery disc will do what I need to do, ideas?

  You should have the ability to create a recovery disk. Otherwise, you will need to use the following method to move it to a new hard drive:

  How to pass Windows 7 on a bigger hard drive: Notebooks.com

• I CS5.5 Master Collection and you want to transfer to a new laptop.  The CS5.5 was an update for CS3 Design standard and I have all the disks and serial numbers.  I just uninstall both programs a laptop and install them on the other?

  I CS5.5 Master Collection and you want to transfer to a new laptop.  The CS5.5 was an update for CS3 Design standard and I have all the disks and serial numbers.  I just uninstall both programs a laptop and install them on the other?

  You can do it, but you don't have to install cs3 in order to install your upgrade of cs5.5.

  You can launch the installation of cs5.5 and you will be asked your cs5.5 serial number.  Setup will ask you then select the product (in a drop-down list) calling.  Select cs3 and you will be prompted for the serial number for cs3.

  Enter the correct number at the right time and to proceed with the installation.

  If you no longer need these programs on your old laptop, disable (help > deactivate) before uninstalling so that you can keep your two activations.

• Satellite T130-17F - upgrade to the Mini-PCI Wireless card

  Card WiFi in Satellite T130-17F doesn't support the 802. 11A / 5 GHz. I would like to replace it with one that is supported. Is this possible? If so, are there any documents that show how do?

  Thanks in advance, Igor Bukanov

  Hi mate

  Usually the laptop supports WLan miniPCI module. This means that usually the other WLan miniPCI cards should work, but I read also here in the forum that it is not always the case and sometimes other WLan miniPCI card would not me recognized correctly.

  But why you try n t a simple solution like a USB WLan stick?
  It is the simpler and in my opinion the best solution for you.
  You will not need to disassemble the laptop. This means that there is no risk of damage and the warranty

  That's why I recommend you try this solution.

• I was using my MacBook today and it crashed and the dock turned silv, I restarted the mac and it was always the same, then I loaded the disk utility and checked the disk and it says disk is fine. It flashes inconsistently gray and the dock turned

  I was using my MacBook today and it crashed and the dock turned silver, I restarted the mac and it was always the same, then I loaded the disk utility and checked the disk and it says disk is fine. It flashes inconsistently gray and the dock has transformed money! I tried to restore Mac OS and then also the same!
  OS El Capitan

  This can help:

  Reboot safe mode (it is a slow process):

  -stop of the mac

  -Start up the mac in shift, press and hold until you see appear it to progress bar, so you can let go

  -When everything started, connect

  -Once connected, stop the mac once again, nothing else is necessary.

  -restart normally.

  Lex

  PS: This clears all system caches.

• I'm having a problem reinstalling Windows XP. After formatting the disk and create partitions, it will not complete the installation.

  Problem reinstalling Windows XP

  I'm having a problem reinstalling Windows XP.  After formatting the disk and create partitions, it will not complete the installation.  He goes back and reinstall Windows again.  I go through the installation of 39 minutes, the computer restarts to complete and it loops back and start the installation again. Why it does this and what I can do to move beyond this?

  Go into the BIOS and make sure that you your hard drive is not set to off, and that is the first priority boot CD and your second HD.

  Don't push when it restarts anything just to let him do what he does and report back if anything I'm sorry I have no idea.

• The video file can be published to the specified location. Check that the publishing location is still available, that there is enough free space on the disk, and then republish the movie again.

  It happened once before, but it somehow went away after I restarted my laptop. I restarted my laptop, this time, but it has not worked.

  ~*~

  OK, so I just finished put a video together. It consists of a Hypercam 2 record (which means it's a .avi file), a PNG image, text and a song (which is a WMA file).

  ~*~

  I save the file, and then click Publish Movie. Everything goes well until the last step where the video is actually published. The window made a break for a while before you receive the following message;

  ~*~

  "Cannot complete the movie publish .

  The video file cannot be published to the specified location. "Check that the publishing location is still available, that there is enough free space on the disk and then republish the movie again."

  ~*~

  I know there are a lot of free space on the drive on my laptop (it's an Inspiron 1520), and that there is nothing wrong with any of my files. I tried to change places without result. It simply doesn't get it. It would be a great help to me if someone could tell me what is the problem :)

  ~*~

  Thank you very much

  Len

  Microsoft Windows Movie Maker is not to let me publish my movies

  Hello

  I suggest you try the steps mentioned in the link given below.

  Error message when you try to publish a movie using Windows Movie Maker in Windows Vista: "cannot complete publish movie.

  http://support.Microsoft.com/kb/930435

  Additional information:

  Solve problems with publishing a movie to your computer

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-problems-with-publishing-a-movie-to-your-computer