Satellite A200-1CR: Vista Ultimate - cannot use BT

Similar Questions

• Satellite A200-13O: Vista Ultimate to basic installation help

  I need assistance to the full installation of Windows Vista Edition in my A200-13O.
  My current operating system is Windows Vista Basic and I want to upgrade to Windows Vista Ultimate.
  Based on the download section of driver I need the following drivers must be installed.

  1 Windows Vista RTM
  2 native Intel ICH7M Chipset utility
  3 945GM Intel display driver
  or
  3 nVIDIA Display Driver G72MV-A3/NB7P-GS
  Realtek Audio driver ALC861D 4
  5 Realtek 8101E 10/100 / Driver LAN Gigabit 8111
  6 Synaptics Touch Pad Driver (with LuxPad)
  7 ALPS Touch Pad Driver
  8 card reader TI Multiple digital media
  9 TOSHIBA software modem
  10 Golan Intel Wireless LAN Driver
  11 Kedron Intel Wireless LAN Driver
  12 Atheros Wireless LAN Driver
  Camera Chicony 13 software
  14 Bluetooth Stack for Windows by Toshiba
  15 Bluetooth monitor
  16 TOSHIBA Value Added Package
  17 TOSHIBA Flash Cards Support utility
  TOSHIBA 18 hardware configuration utility
  19 TOSHIBA supervisor password
  20 TOSHIBA SD Memory utilities
  21 TOSHIBA ConfigFree
  22 TOSHIBA Assist
  TOSHIBA Speech System 23
  24 TOSHIBA Extended tiles for Mobility Center Windows V1.01
  TOSHIBA Fingerprint Utility V5.6.0.3221 25

  I have already downloaded most of them, but I can't find some like [2] utility Intel ICH7M Chipset, driver of Kedron Intel wireless LAN [11], [23] TOSHIBA Speech System. Also some drivers are not installed properly.

  Can you please help me.

  Chipset driver you can get on the Intel Web site
  www.Intel.com
  But I think that the pilot could also be in the display driver because it s the same chip.

  The WLAN driver I found on the Toshiba site so download and install it.

  The speech system could be integrated into the audio driver.
  But download and install all the drivers and the system will work.

• Satellite A200: After Vista Ultimate upgrade Chicony webcam does not work

  Hello

  I hope someone can help me. For 3 weeks, I have buy the Toshiba A200 with Windows Vista Home Premium and very good built-in Webcam function. I have no problem.

  Yesterday I did an upgrade to Windows Vista Edition full and now the Webcam does not work.
  Every time when I want to launch the following software message come «Please activate the webcam»

  In the it´s control panel that wrote this function of Doesna´t of hardware because the software isn't fair. But I have the right software. I have try the original software on me the hard drive and, of course, I do a download from Toshiba and I try this.
  But I still got the same message.

  Please help me.

  Hello

  I m not an A200 owner and, therefore, I can not say much about this webcam tool, but to my eyes the Chicony webcam software should work with Windows Vista Ultimate Edition, because this version is almost the same as Windows Vista Home Premium. The ultimate version supports more features like Home Premium, but the software is running and must be compatible with both versions of Vista.

  How did you install Vista Ultimate? You perform a new installation of the OS, or you upgrade only the Home Premium-> Ultimate?

  Anyway, currently version 1.0 of the Chicony camera software is available on the Toshiba page.
  You may need to wait until the new update has been published.

  By the way: also check these threads;
  http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?threadID=23587&MessageID=87055
  http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?threadID=24161&MessageID=88732

  Good bye

• Integrated ACPI controller Satellite A200-1CR

  Hello

  Recently I reinstalled my laptop Satellite A200-1CR vista and installed Windows XP, after a certain time a notification message began to appear stating that "new hardware found".

  Something to do with "ACPI Embedded Contoroller. Update the BIOS has not fixed this problem. So please help me sprt outside concern.

  Thanks in advance!

  Vugar

  Hello

  at first you need to go to this site and make sure if you have downloaded and installed ALL! drivers listed on this site for YOUR model:

  http://EU.computers.Toshiba-Europe.com/cgi-bin/ToshibaCSG/download_drivers_bios.jsp?service=EU

  To find out which model you choose, just look on the label of money bit on the bottom of your machine. There's the model number!

  Otherwise, go here and check this link to support Toshiba for more information:

  http://support.toshiba-tro.de/KB0/TSB7501W20006R01.htm

  See you soon

• Satellite A200-1CR: can I install Vista using my Vista DVD installations?

  Hello

  I would like to get some answers to my questions...

  I have the satellite A200-1CR (PSAE0) and I want to install vista on my own... not with the recovery DVD but I have some serious questions...

  (1) may I have problems during the installation... (Drivers SATA, etc.), problems of BIOS or Toshiba has no restrictions?

  (2) what problem if I erase the secret (winre) partition and what is its purpose?

  (3) if I do a clean install with my DVD with my vista... If I want in a future close that I can use the recovery DVDs I got it or not?

  (4) to the drivers section for my laptop for each part has 5,6,7 or 8 drivers for win vista... which is good, or it's all the same?

  (5) in general, what do you propose? Are there reasons why not to do my format? I did a large number of formats in desktop, but never in the notebooks.

  Sorry if you tired with my questions and sometimes my bad English...
  Thank you in advance...

  Why not.

  As to the question;

  (1) possibly the Vista operating system does not recognize the HARD drive during the installation of the OS. In this case you must install storage Intel Matrix (Robson package) Manager first! It of a driver SATA and can be found on the Toshiba or Intel driver page.

  (2) Windows recovery environment (WinRE) is placed on the hidden partition and it of necessary to restore a damaged operating system.
  The Vista operating system automatically creates the hidden partition and Windows re installing the OS.

  (3) Yes, you can use the Toshiba Recovery CD. But it erases the entire HARD drive always.

  (4) take a newer version

  (5) generally I put t see any reasons to get in shape. The preinstalled Vista operating system has been configured and all the tools of Toshiba, drivers and additional software should work very well.
  I don't recommend a new format if the operating system is working well.

  Good bye

• Cannot use the webcam with chat programs - Satellite A200-AH7 Vista

  Satellite A200-AH7/Vista Home Premim/Chicony USB 2.0 built in webcam

  I can't understand how get the audio works with built in chicony webcam when in a chat program or any program for that matter. I can record audio and reading later, but this isn't what I want to do. It's probably just something stupid that miss me... but any help would sure be appreciated... I tried with Windows Live and Yahoo messenger, and so far all I can do is wave to people LOL. I was never able to get it to work... any ideas?

  Today I bought a Logitech Quickcam for notebooks in case the problem is with the construction in camera. I don't want to install it unless absolutely necessary and think I would need to uninstall the Chicony to make it work... someone can point me in the right direction?

  I just want to be able to talk to my grandchildren...

  Thanks in advance,
  Sue

  Hello

  He is a Canadian for Toshiba laptop model.
  Please see the Toshiba Canada Web site to get the right webcam software:

  http://209.167.114.38/support/TechSupport/ln_TechSupport.asp

  First remove the old webcam software. Reboot the laptop. Clean the registry and the system using the CCleaner (it of free). Reboot the laptop again one and then install the new software of webcam!

  Welcome them

• How to change Vista Basic to Windows XP Home SP2 on Satellite A200-1CR edition?

  Hello

  Since a few days, I bought a Toshiba Satellite A200-1CR. I am very satisfied with the laptop, although I do not work for Vista Home Basic Edition, because it is not to support the programs of the sum, so I change my operating system from Vista Home Basic to Windows XP SP2 home edition.

  If I prefer to reformat the laptop and install Windows XP service pack 2 (32-bit or 64-bit, not sure yet).
  However I do not know if I have to do something special for him, because it's my first laptop I have and I haven't had that one time a laptop with drivers on a CD. Now I m operating system, I think I need a driver s disc switching.

  If I changed vista to XP is there any software support?
  Vista for XP service pack2 change possible or not?
  Someone help me. If changing the operating system where I can get the driver software?

  Hello

  Yes, you can install Windows XP SP2.

  There are two things you need to be aware of:

  (1) you need a SATA of F6 driver on a floppy disk when installing XP. Otherwise XP does not detect the SATA HDD. Search for "SATA" of this section, it is already been covered several times.

  (2) after installing XP, you should download and install the XP A200 drivers from the Toshiba Europe Support/Drivers site

• Satellite A200-1CR - cannot find my BIOS

  Hello

  I have a Satellite A200-1CR (part number: PSAE0E-02G00YAR) and I can not find my BIOS. I need to make a crysis recovery disk as I interbted the update of the BIOS. Any help to find the file please?

  And observations about crysis recovery thing is more than welcome :D

  Thanks in advance everyone

  Hi iq860,

  Official website of Toshiba, you can download the latest version of the BIOS, but you can find it here:
  http://EU.computers.Toshiba-Europe.com > support & downloads > download drivers

  Satellite A200 is a little more if you can find it in * Archives *:
  * Archive * > Satellite > Satellite a series > Satellite A200

  I hope that helps! :)

• Question about shortcuts FN on a Satellite A200-1CR

  HY
  I have a problem... or that's what I think it is... I bought a new TOSHIBA Satellite A200-1CR with Vista Home Basic preinstalled and I upgraded to Vista Business. The problem is in what regards the use of the FN key with additional shortcuts... With the help of these shortcuts is tricky because I don't really know how they work... Under Windows, after starting at the top of the screen, I have a few buttons (exactly the FN shortcuts) that I can use by keeping the mouse over and they slide down, but the problem is that after these buttons appear to the use of the FN keyboard hotkeys is disabeled... or kind, because I can use FN + F9 , FN + F10 shortcut FN + F11. Please help me and tell me if this is normal... and if not tell me how can I fix. Thank you!

  Hello
  Oh, that's normal, Don t worry. You can disable the buttons and then a little work with the FN keys.
  Just remove that bar on the top of the autostart and he won´t bother you more.

  Welcome them

• Satellite A200-1CR: how to change the language of the OS of the Russia into English

  I am a student sri-Lanka, Russia.
  I bought a toshiba satellite A200-1CR Russia laptop computer, but it came with windows vista basic Russian.
  So I can't understand anything and the dealer said that they cannot change the language to English.

  So, how can I get the English vista and drivers.
  Please answer me to my private email address.
  (Toshiba satellite A200-1CR

  [email protected]

  If you want to install the English operating system, you must get OS DVD facilities on English. All the drivers, tools and utilities for your laptop, you can find on Toshiba page under http://eu.computers.toshiba-europe.com/cgi-bin/ToshibaCSG/download_drivers_bios.jsp for assistance

  All that s!

• Satellite A200-1CR - black screen and no boot

  Model:
  Toshiba Satellite A200-1CR

  Question:
  By pressing the power button to power on the computer for a full boot, the power LED lights up but still black screen (not even of lighting). The logo led 'Satellite' in the lower left corner of the chassis remains off while the HARD drive has made a unique quick snap; DVD activity led (the device) always remains on even without any CD inserted, by pressing the eject button do nothing (status bar is locked) and no sounds of activity.
  No logo screen of boot (show stays), not of beeps dark and wide, no DVD or HARD disk activity, keyboard seems does not (all combinations that should light up an led, capslock, numlock, etc, does nothing), the fan works.

  I have already (without success) tried:
  -Unlock the tray, insert the rescue CD and power on
  -Remove the main battery and power on with AC adapter only
  -Insert a bootable USB stick/external HARD drive

  The computer worked as expected the day before and there has not been any kind of shock. Described is the situation I faced when I turned on the next time (only 24 hours later).

  What could be wrong?
  Thank you.

  > By pressing the power button to power on the computer for a full boot, the power led turns on but screen stays black

  Well, looks like hardware problem; Maybe the memory problem or something serious with the mother or the CPU. It of really difficult to say what could cause this.
  You can try to check the RAM modules.
  Trying to start using a maybe only module, it is useful in the case otherwise I fear, you will need assistance from technicians Toshiba ASP m

• Satellite A200-1CR does not recognize the module of RAM 2 GB

  Hello

  I have a problem with the extension of the RAM.
  I have the Satellite A200-1CR with 2 x 512 MB of RAM.

  Now, I bought 1 x 2 GB RAM (DDR2 PC2-5300 (667 MHz); PA3513S-1M2G) but the BIOS and Windows recognizes only 1 GB.
  When I add 1x512mo to the second slot, the system recognizes 1.5 GB of RAM.
  Where is the problem?

  What should I do to make it see 2 GB?

  Paula

  Hello

  I think the answer is very simple.
  Satellite A200-1CR can be upgraded up to 2 GB of RAM.
  This means that you can use max 1 GB of RAM in one slot
  You used 2 GB of RAM and this module does not seem to be compatible
  In my opinion if you want to use 2 GB of RAM then you can buy 2 x 1 GB RAM modules

  Welcome them

• Satellite A200 - 1CR PSAE0E DVD disc does not apper in workstation

  I am the owner of the computer laptop above Satellite A200-1CR PSAE0E-02G00YA
  RAND, I have problems with my DVD - RW DRIVE.

  I can't see under my computer.
  I am running Windows Vista and need a driver updated that I can't find anywhere.

  Please help as soon as possible... Thank you

  Hello

  Try this short workaround:
  -Go to Device Manager and remove right CD / / DVD drive from the list of devices
  -Start the registry and delete the Upperfilters and Lowerfilters completely from the following registry key values: HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Contro l\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}
  -restart the laptop

  Now after the laptop has rebooted, the OS should reinstall the STRANGE and the STRANGE should appear in my computer.

  Welcome them
  Jack

• Technical need info on satellite A200-1CR

  Hello!

  I have a laptop Satellite A200-1CR. I can't find any technical info on the toshiba homepage.
  I registered my laptop, when I click on properties of my notbook, become after messsage:
  "I'm sorry, but this product is not available in your region."

  I can't find it in the A200 list too. (over 15 models without my 1CR)
  My problem is that I don't know the settings of my laptop. I didn't ' know how can I upgrade without this info. For example, chipset, cpu, max FSB socket, etc.
  Can someone help me?

  Don't work on my laptop or not product online Information Service.
  Any suggestion?

  Thank you very much!

  I find a Toshiba brochure that provides many useful information on your laptop:
  http://EU.computers.Toshiba-Europe.com/contents/Toshiba_teg/EU/others/brochures/April07/en-DB_NB_ProductGuide_Apr07_low.PDF

  In addition, you might find a lot of useful information in the manual of the user which is preinstalled on your laptop. Should check out!

  A tip;
  You want to find information on your hardware specifications, try to install a tool like Everest home for hardware diagnosis.

• 1IZ satellite A200 with Vista crashes every day without no reason

  Hello guys,.

  I have a Satellite A200 with Vista Home Premium installed. In the past months, the BONE is suspended every day, I was not able to detect the reason. nothing is having replied to the questionnaire, not even Ctrl-Alt-Delete, the only solution is to stop from the power switch.
  I do not found something wrong in the system log, so I do not know what to do. Toshiba PC diagnostic shows everithing OK.

  What can I do? Perhaps a cooling problem? A guide for cleaning?

  Thank you.

  Hello

  So to be honest, it's hard to say what are the really causes your system to hang. Possible reasons:

  HIV 1-infected
  2 problem of file system Os including drivers, programms...
  3 had to be clean
  hardware problem 4

  I recommend:

  1 search for viruses
  2 reinstall the drivers (especially as a vga and chipset drivers). Check installed programs
  3 use compressed air jet to blow off the dust from the cooling module.

  If this does not help, do a fresh install of the operating system. Then we will see what to do

  Welcome them