Satellite A210 PSAEGE - need to control the driver XP for bus

Similar Questions

• Satellite A210-1BQ - need Dual Mode Pad Driver for Win 7

  Hello

  I have a Satellite A210-1BQ and installed Windows 7 above.
  But niw, my work doesn´t of the Dual Mode button.
  The work of drivers for Windows Vista don t.

  So is there a special driver for Windows 7?
  I m now works with a MS Wireless Mobile Mouse 6000. This mouse replaces the driver for the Touchpad?
  I tried FN + F9 and I uninstalled all of the mouse on the laptop driver, but it won´t work.

  Hello

  I assume you are using Win7 32 bit version, right?
  Did you clean Win7 installation or you have upgraded Vista to Win7?

  Generally speaking if you can't find the version Win7 Vista driver should work.
  Which we tested, ALPS, Synaptics, or both?

  If you use an external mouse and use a specific driver for it. do not crush the touchpad.

• Need drivers XP for Satellite A210 PSAEG

  I bought a laptop on the model of Satellite A210 (PSAEG).
  But I don't want to use Windows Vista. But I can't find the XP drivers for this model... How can I find them

  Hey Buddy,

  to find a few XP drivers, you can check the driver Toshiba download website. Here´s the link to the site where you can find and get the drivers:

  http://EU.computers.Toshiba-Europe.com/cgi-bin/ToshibaCSG/download_drivers_bios.jsp

  Welcome and good weekend

• Satellite A210-171: need XP display driver

  Hello

  I bought Equium A210 with Microsoft Windows Vista... I some how manage to get drivers Wireless LAN for XP but I don't know where to find the display drivers please someone tell me...

  Thanks a lot, I really need to do so much work and its just crashes me...

  Thank you

  Well, I checked Toshiba European page and there is not a lot of drivers XP for Equium A210.
  But don t you worry man. I think that you are not lost ;)

  As far as I know, that this device supports ATI Radeon X 1200 graphics card.

  Some units of the Satellite A210 series were equipped with the same graphic card.
  So please check the Satellite A210 series (there are different so go through A210 all singles series) and try some graphics drivers ATI posted on the European driver Toshiba page.

  These drivers must run.

• Satellite A210 restore failed (error: run the Chkdsk utility)

  I have a Toshiba Satellite A210... When I tried to reform. There, an error came (about 47% in the 'process'); blablablabla... This file is corrupt, run Chkdsk utility...
  Help please?
  Then. Should I try call Toshiba or send it?

  Help me please, anyone? :))

  It's not easy to say what the problem is.

  On the Toshiba website, I founded a updated firmware for drives optical drives in Satellite A210.
  Then, look at the Toshiba site and try this update of the firmware if you have such a unit.

  The next step if you have no success with the update of the firmware, you should try a Microsoft installation disc.
  In addition, it could also be a problem with the HARD drive.
  You can do a test drive with Drive Fitness Test.

• Do not know how to install the driver LAN for Satellite A100-787

  The driver LAN for Satellite A100-787 is delivered with no configuration file and windows hardware installation does not recognize.

  I don't know how to install it... Any help?

  Hello

  I guess you are trying to install the driver LAN WXP because Vista LAN driver is not available. Am I wrong?

  In any case:
  -Create a new folder on your desktop
  -extract all downloaded files here
  -Open Device Manager and right-click on device unknown you want to install
  -choose Properties
  -find the Install driver button
  -Click on it and go to the new folder created
  -Follow the on-screen menu

  I hope that you can install to ti the pilot FTAs.

  Good bye

• A60: Need to download the driver for powersaver

  Hi there I have recently upgraded to windows xp pro, I have a toshiba A60 and I need to download the driver for powersaver. Is someone can please tell me why this is not possible, as at the end of the installation it says fatal error.
  Any help will be much appreciated.

  Hello

  Have you downloaded the latest version of the power utility of Eve from Toshiba download sites?
  Please see this site:
  http://EU.computers.Toshiba-Europe.com/cgi-bin/ToshibaCSG/download_drivers_bios.jsp

  Good bye

• I need to change the drive to a new drive letter, but XP will not let me because he thinks that the letter is in use.

  Quick question: I need to change the drive to a new drive letter, but XP will not let me because he thinks that the letter is in use, when it is not.

  The question for a long time: I've updated two disks in my computer from 1 TB to 2 TB. They were e and K:. The KC: drive is used as a backup of data on E: drive.

  I copied all the data on the old drive E: to the new, but when I put the new drive in place of the old, XP wouldn't let me assign the E: drive letter. It is ironic that several times, I see the warning that if you change a drive letter, some programs may not work - so of course that Microsoft is aware of this problem - however, it is annoying when you NEED to change a drive letter to OPERATE programs, but Windows won't let you. Sometimes, trying to protect users from doing stupid things prevents them from making things work...

  Anyway, after some research, I discovered that if I put the drive E: OLD and "remove" the drive of her letter, then the letter E: becomes available again. It did not work, and my computer is now partially satisfied with his new E: drive. However, the same trick with the new drive K: does NOT work.

  I removed the letter 'k': the old K: drive, but when I install a new one, it won't let me change it. It happens to be stuck at 'l': it's no use to me because backup programs are ready to use the K:\ path.

  There is that no "K:" drive in my computer and I deleted the letter k: the old disk. How do I FORCE XP to designate the new drive K: so that my backup program can work again?

  Thank you.

  Did you try to start your computer in Mode without fail (repeatedly, key to tap the F8 as your computer starts) and then try to re-assignment of drive letters?
  I think that some programs on your machine may be playing with your drive letters.  Boot safe mode will allow Windows to operate with a minimum of processes that are running and you should be able to change drive letters in these conditions.

  HTH,
  JW

• You need to set the drive letter to the USB Ports front before any device has been inserted - that won't change when the device is connected. I have Windows XP Professional with Visual Studio 6 installed

  You need to set the drive letter to the USB Ports front before any device has been inserted - that won't change when the device is connected. I have Windows XP Professional with Visual Studio 6 installed. Thanks for your help

  diana73,

  First of all, make sure that you're connected Administrators account to do.

  How to change a drive letter to change an existing drive letter on a drive, on a partition, or a volume, follow these steps:

  1. Sign in as an administrator or as a member of the Administrators group.
  2. Click Start , click run and type compmgmt.msc .
  3. In the left pane, and then click disk management .
  4. Right click on the drive, the partition, the logical drive or volume that you want to assign a drive letter to and then click change drive letter and paths .
  5. Click change .
  6. Click assign the following drive letter if it is not already selected, click the drive letter that you want to use, and then click OK .
  7. Click Yes when you are prompted to confirm the drive letter change.

  The letter of the drive, partition, or volume that you specified is changed, and the new drive letter is displayed in the appropriate drive, partition, or volume in the disk management tool.

  Good luck! Please rate me upward if you find my post helpful. Thank you!

• 5530 Evvy replaced printer - need to replace the driver and software?

  Hello

  Recently, I had to feel my 5530 all-in-One printer replaced while it was still under warranty. The replacement came with new driver software and everything, but since it is the same model that I decided not to install it and use the existing driver installed on computers instead. (Replacement not be come with directions for uninstall, said by the way.)

  The new printer is connected to the wireless network (using touch screen) and is recognized by computers on the network, but I can't get anything to print, since the existing driver HP software does not seem to 'find' the printer. Do I still need to uninstall the driver and reinstall? And what about the other programs installed with HP printer?

  The computers are all Windows 7 64 bit.  I'm not very technical, so it makes me a little nervous.

  Thanks for any help you can give.

  Running the diagnostics to http://www.hp.com/go/tools can help solve the problem.

• PHANTON Drive; When I try to open the my computer Explorer window is white and I get a message that I need to format the drive F.

  Hello

  I have a laptop running Windows 7 Home Premium 64-bit.  The HARD drive is configured to have a small partition for reserved system, Partition C for the system and the Partiton E for my files.  D drive is the DVD ROM Drive.

  Very occasionally when I try to open the my computer Explorer window is white and I get a message that I need to format the drive F.  I did not have a permanent Drive F and when this happened had no other connected devices.

  Drive F is often used, as are other drive letters, by various devices from time to time, such as external hard drives, Flash, my TomTom SatNav players, camera, readers of cards etc.

  Can someone explain why this happens and if I can do something to stop what is happening in the future?

  Eric

  Some Dell computers hard drives are extremely sensitive, if your computer is DELL' consider the technical service. Because if you run recovery, you have a headache.

• Laptop HP 15-r033TX: did not find the driver wifi for my laptop to windows 7 64 bit

  Hello

  I need help. I did find the driver wifi for my laptop for windows 7 64 bit. Can you send me a useful link.

  Thank you

  Hello:

  Here is the link to the wireless card driver you need...

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-131223-1 & CC = US & DLC = in & LC = on & JumpID = reg_r1002_usen_c-001_title_r0005

  You will also need the bluetooth driver...

  http://h20566.www2.HP.com/hpsc/SWD/public/detail?swItemId=ob_130390_1

• need to know which driver download for dell 1525, or windows vista basic

  need to know which driver download for dell 1525, or windows vista basic

  Dell Inspiron 1525 drivers: http://support.dell.com/support/downloads/driverslist.aspx?c=us&l=en&s=gen&ServiceTag=&SystemID=INS_PNT_PM_1525&os=WLH&osl=en&catid=&impid=

  Choose your operating system from the drop-down list.

  J W Stuart: http://www.pagestart.com

• I've uninstalled and reinstalled the drive several times with the same result, my problem is when I download the drive icons for my browsers and above all my desktop icons change adobe logo, so when I click on them Adobe tries to open them.

  I've uninstalled and reinstalled the drive several times with the same result, my problem is when I download the drive icons for my browsers and changing most of my the desktop icons for the adobe logo, so when I click on them Adobe tries to open them, of course, he does not format because it's not an adobe application , so I tried to restore the computer to an earlier date and it wont let me as long as Adobe reader is installed, so I need to uninstall and now I have nothing to open files and downloads of Adobe, someone had this problem and if so, did you get it resolved? Thank you Tommy...

  This may help: Application, file icons change in Acrobat/Reader icon

• How to install the driver jdbc for sql server 2005 in sql developer 4.0?

  
  Hallo all

  I need to access the tables in a MS SQL Server 2005 database.

  The JDBC driver is possible.

  How to install this driver?

  Thanks a lot for your messages.

  Hello

  It's the documentation-

  Database: third-party JDBC Drivers

  The component drivers JDBC third party specifies drivers to use for connections to the third-party databases (non-Oracle), such as IBM DB2, MySQL, Microsoft SQL Server or Sybase Adaptive Server. (You don't need to add a driver for connections to Microsoft Access databases.) To add a driver, click Add an entry and select the path for the driver:

  For Microsoft SQL Server or Sybase Adaptive Server: jtds - 1.2.jar, which is included in the download of jtds - 1.2 - dist.zip

  To find a specific third-party driver, visit the appropriate site (for example, http://www.mysql.com for MySQL Connector/J JDBC driver for MySQL, http://jtds.sourceforge.net/ for the for Microsoft SQL Server and Sybase Adaptive Server jTDS driver, or search for Teradata JDBC driver to http://www.teradata.com/ ). For MySQL, use the driver in MySQL 5.0 not 5.1 or a later version with the version of SQL Developer 1.5.

  You must specify a third-party driver or install a driver using the check for updates feature before you can create a connection to a database to third parties of the associated type. (See the tabs to create connections to the databases of third parties in the Create/Edit/Select database connection dialog box).

  Alternative:

  As an alternative to the use of this preference, you can click Help, and then search for the updates install the for Microsoft SQL Server JTDS JDBC driver and the driver of JDBE of MySQL as extensions.

  Kind regards

  Mike