Satellite A215-S4757 blue screen & startup failure after HARD drive partitioning

Similar Questions

• Satellite A500-1GH blue screen when copying to usb drive.

  Hello everyone

  I'm new to this forum and I need your help.

  I have a new toshiba Satellite A500-1gh with windows 7 ultimate 64-bit.
  It works perfectly, but I have problems when im trying to copy to my/on my portable usb drive.

  He copy some data and then blue screen of death.
  I tried to check my RAM with memtest, but it restarts my pc once he starts the first tests.

  Can someone help me?

  Hello

  Is it only happens using USB drive?
  Have you tried other disks USB, key USB flash or other USB devices?

  > I tried to check my RAM with memtest, but it restarts my pc once he starts the first tests.
  Hmm... It's strange...
  The problem of memory could be responsible for BSOD, but if this BSOD appears only using USB drive then I would recommend testing other external USB HDD.

  You should also try to update the driver from chipset since the chipset USB ports driver controls

• Blue screen error CANNOT ACCESS HARD DRIVE SPACE

  I'm trying to install windows xp after removing windows 8 of my computer and creat new partition using the boot disk windows 98se, fdisk, but the installation during windows startup I get in trouble when get a blue error message screen telling
  "YOUR COMPUTER'S STARTUP PROGRAM CANNOT ACCESS THE DISK THAT CONTAINS THE PARTITION FREE SPACE, YOU CHOOSE. CANNOT INSTALL WINDOWS XP ON THIS HARD DRIVE. »
  Image of the screen available message if necessary. There is no error due to this error code.
  Please help me to solve the problem, and I'll be really thankful to you.
  Kind regards
  Kay

  First of all, you need not use a setup of Windows 98 to work partition disk before installing Windows XP, Setup of Windows XP has the tools to do this job.

  Windows XP Setup cannot see the hard drive as it doesn't have drivers for the SATA controller on board.  To install Windows XP you must go into the BIOS and put the hard drive in IDE mode you will need to integrate the SATA drivers in the XP installation CD, or you need to feed them to the Windows XP Installer with a floppy using the F6 method drive.

  Your new PC does support Windows XP, it has Windows XP drivers available for it?  If this isn't the case, you will have a lot of crying by train to get there.

  John

• Get blue screen errors. My hard drive died?

  Original title: hard drive crash?

  Finally, my hard drive failed? A few months ago, I had a virus so I had to back up my entire hard drive on my Toshiba laptop. After I did this whenever I started it, I had to press F12 to load device of your choice. Then he said something on the hard drive failure 4, stuff like this press F1 to continue. I usually do and it runs slow but the other day I went through the process, and he came to load Windows XP then blue screened with c:0000218 (a registry file failure). I've tried safe mode, safe mode with command prompt last good known configuration and start normall. I always get blue screen and sends me in a boot loop. I tried also to insert the OS and restore CD that has not been loaded. Went through the process above.

  Finally, my hard drive failed? A few months ago, I had a virus so I had to back up my entire hard drive on my Toshiba laptop. After I did this whenever I started it, I had to press F12 to load device of your choice. Then he said something on the hard drive failure 4, stuff like this press F1 to continue. I usually do and it runs slow but the other day I went through the process, and he came to load Windows XP then blue screened with c:0000218 (a registry file failure). I've tried safe mode, safe mode with command prompt last good known configuration and start normall. I always get blue screen and sends me in a boot loop. I tried also to insert the OS and restore CD that has not been loaded. Went through the process above.

  What do you have with regard to the virus out of your backup drive?

  How - to what support - did you back up your drive?

  Is a version of Norton antivirus or security program installed?

  When you use F12 to select boot device, what device were chosen to boot from?

  The message you have seen 'SMART failure provided on disk hard 4' followed by an identification of the drive?  What disk drive has been identified?

  What happened when you tried to use the CD "OS and recovery?  Please report any error completely, without paraphrasing.

  See the following tips from frequent poster Jose Ibarra:

  For those who STOP: c0000218 error, a chkdsk /r usually will fix you right up and then you will start normally once again, then it will be broken again with the same problem until you run chkdsk /r once again, so you have to work, do what you have to do when you get started - uninstall Norton completely and correctly.

  After the chkdsk/r, you will still be able to boot mode safe but as Norton components not load safe mode and rush through the file system when loading.  Then you can go on the WWW of Norton of the site and use their instructions to get rid of the beast to uninstall...

  [https://www-secure.symantec.com/norton-support/jsp/help-solutions.jsp?lg=english&ct=united+states&docid=20080710133834EN&product=home&version=1&pvid=f-home]

  Here are some instructions in order to at least run the Recovery Console:

  If you have no XP bootable media (or aren't sure you have) create a bootable XP Recovery CD of Console and do not forget.

  This is not the same as recovery disks that might have come with the acquisition of the system store.

  You can make a bootable Recovery Console CD by downloading an ISO file and burn it to a CD.

  The ISO bootable image file you need to download is called:

  xp_rec_con. ISO

  Download the ISO from here:

  http://www.mediafire.com/?ueyyzfymmig

  Use a new CD and this simple and free program to burn your ISO file and create your bootable CD:

  http://www.ImgBurn.com/

  Here are some instructions for ImgBurn:

  http://Forum.ImgBurn.com/index.php?showtopic=61

  It would be a good idea to test your bootable CD on a computer running.

  You may need to adjust the computer BIOS settings to use the CD-ROM drive as the first device to boot instead of the hard drive.  These adjustments are made before Windows tries to load.  If you miss it, you will need to restart the system again.

  When you start on the CD, follow the instructions:

  Press any key to boot from CD...

  Installing Windows... going to pronounce.

  Press 'R' to enter the Recovery Console.

  Select the installation that you want to access (usually 1: C:\WINDOWS)

  You may be asked to enter the password (usually empty).

  You should be in the folder C:\WINDOWS.  It's the same as the

  C:\Windows folder that you see in Solution Explorer.

  The Recovery Console allows base as file commands: copy, rename, replace, delete, chkdsk, fixboot, fixmbr, cd, etc.

  For a list of the commands in the Recovery Console, type help at the prompt of commands or read on here XP Recovery Console:

  http://www.Microsoft.com/resources/documentation/Windows/XP/all/proddocs/en-us/recovery_console_cmds.mspx?mfr=true

  A good idea before you start things must first verify the integrity of your file system by using the chkdsk command.

  In the command prompt window, run the chkdsk command on the drive where Windows is installed to try to fix any problems on the afflicted player.

  Running chkdsk is fine, even if he finds no problem.  It won't hurt anything to run it.

  Assuming your boot drive is C, run the following command:

  CHKDSK C: /r

  Let chkdsk finish to correct the problems, he could find.

  It may take a long time for chkdsk complete or they seem to be "stuck".  Be patient.  If the HARD drive led blinks always, chkdsk is something.  Keep an eye on the amount of the percentage to be sure that it is still making progress.  It may even seem to go back sometime.

  You must run chkdsk/r again until it finds no error to correct.

  Remove the CD, and then type "exit" to exit the RC and restart the computer.

  You have not to set the BIOS to boot the disk HARD since the CD won't be.

• Satellite M70 - after HARD drive partitioned, the OS does not start

  Hello

  Good then this is a real doozy, and I hope that someone will help.

  I started to fix my satellite m70 girlfriends using the disc of recovery etc, everything went fantastic, the HARD disk has been erased and Windows + all software has been reinstalled.

  Then I thought it would be a good idea to use partition magic to partition the hard drive, so I chose the main hard drive and cut 10GB of it to put in place a new partition.

  I rebooted, and then after Windows restarted again completed.

  NOW, it does not charge, it says no operating system, so I tried to start with the recovery disk and all over again...

  If I click on continue (to start the recovery process), however it is said now that the "Error #1828", free space is too small.

  I'm really angry that this has happened and I just want to start over again.

  Can someone help me with this?
  I can't access the Bios either (not sure if that might help), because I don't know the password (must be a fault im not aware of).

  Help, please.

  Thank you
  SG

  I think that this is the reason why you used a tool to change the size of the partition. At best, this should be done before you install Windows and 10 GB is a little too small for Windows. You must use at least 15-20 GB for the first partition where the BONE is placed.

  To resolve this problem, you must delete all existing partitions before using the recovery disk. Therefore, you can use a Windows XP disk or something else. Just boot from it and delete all partitions. Then the recovery disk should work.
  Check it!

• Inspiron 6000 - won't start Windows - Blue Screen of Death - the hard drive is Toast! Help me!

  I have a Dell Inspiron 6000 2-1/2 years, with XP Media Center.  Last night at the start, he went to the Blue Screen of Death.  I tried to restart about 10 times, each time by selecting a variety such as 'use last known good Configuration, Safe Mode, Etc.' nothing works.  Get to the point where the windows flag is waving in the wind (may be waving goodbye?) and then hangs at Blue Screen of Death.

  To make matters worse, this is the only hard drive, I have not saved for a few months and I can't seem to find my recovery/boot drive... I swear to you that I made a copy when you are prompted 2-1/2 years ago?

  in any case, I started press F12 and got to the dell diagnostic interface.  I ran the tests in the Section of the blue screen, and almost all categories of hard drives contained errors.  I tried Googling some of them and almost all of the shots indicate disk hard death is imminent.

  So, anyone have any ideas how I can:

  1 retrieve the data

  2. get Windows transferred to another hard drive (without having to buy a whole new copy)

  Any help is appreciated deeply... only 3 weeks until final and just lost a huge amount of assignments for my grad. school...

  Thank you

  Aaron

  
  

• Bootcamp option disappeared after hard drive partitioning

  Mr. lonely

  I followed your steps to retrieve the bootcamp startup option if by mistake I partitioned my hard drive on mac.

  Here are the screenshots

  1 do you want to keep this new partition?

  2 Please download Fdisk TPG - https://sourceforge.net/projects/gptfdisk/ - and install it. After the return when you installed.

• ThinkVantage Button takes me to the system recovery after HARD drive partition

  Hello

  I recently bought a W520 with 4 GB of RAM.

  I bought 3 branches of more than 4 GB each, installed and everything was fine. Also, I shrunk the C: drive and created a new disk (D:\) from space, that I rescued after the reduction of the volume.

  When I start the laptop and you want to enter the BIOS setup by pressing the blue ThinkVantage button, she won't go to the BIOS Setup. Rather, it passes through the system recovery options.

  What gives? How can I go to the BIOS Setup?

  Thank you in advance.

  Continuously when the system starts, press F1.

• Satellite Pro 6100: blue screen after overheating problem

  My laptop overheats a year ago and since then I can only use it for about an hour at a time. First sign, it's going to blue screen, it's the hard drive starts clicking and about 5 minutes later, he dies.
  Let it cool down for a few hours, then it is well again. It is not the disc hard as I tested it in another laptop.

  Any ideas?
  I desperately need to work again, it has been the best laptop I've ever owned, and I hate the idea of having to buy a new one with a touchpad.

  Hello

  Generally, the laptop overheats because the cooling module may not work correctly.
  I guess that the blue screen appears because of the overheating.
  In this case, I would recommend checking the cooling fans. Fans cannot work properly because of the dust and debris.
  The use of the vacuum cleaner is the best way to clean the fans.
  But be careful.

  In addition, the square around the laptop must be free. It is important that fans can take a breath.

• Satellite Pro A60: Blue screen - ATI2DVAG display driver. DLL in endless loop

  Hello
  Laptop is a Toshiba Satellite Pro A60 with ATI Mobility Radeon 7000 IGP video card, running Windows XP Professional and SP 2.
  During the start in most cases systems hang up with blue screen.

  I installed the latest drivers from http://uk.computers.toshiba-europe.com/cgi-bin/ToshibaCSG/download_drivers_bios.jsp?service=UK (Version dated 6.14.10.6430 Date 09/03/2004) but the problem continues. After second - last third - it reboot now works.
  The blue screen says (translated from German):
  "Component that probably caused the problem: ati2dvag.dll; the device driver is in an infinite loop; Subsequently the unit does not work, or the device driver is not program the equipment in the right way. STOP 0X000000EA. A dump was created.

  Please HELP - THANKS in advance!
  Best regards
  Frank

  Hello

  I studied a bit on the Toshiba site and found this interesting paper Toshiba on the error message Satellite A60 and blue screen on startup.
  http://support.toshiba-tro.de/KB0/TSB5300X7000MR01.htm

  This document describes how to upgrade the BIOS. The update of the BIOS should help solve this problem. Take a peek inside.
  Please post if you have solved the problem

• Safari gave me a blue screen of death, calling the Microsoft blue screen of death after installing Adobe flash player. The van is responsible for me to a Microsoft third-party technical support I did not trust anyone at - he had a problem with Adobe flash

  Safari gave a blue screen of death after downloading Adobe flash player do not have access to in-house. Big sign telling me that my computer from Microsoft was blocked and to call this number that was, according to the individual, I spoke, a third party provider working for. Microsof. Everyone knows this. I do not trust them especially when they declared they wanted to log into my calculation. Is there one resolution other than OS X Recovery?

  There are hundreds of these sites to scam out there. Nothing has been installed on your Mac, or even downloaded to. The goal of each of them should Miller get so much money that you're ready to spit. Good thing you cut them and not give them access to your Mac.

  The usual simple solution is Force Quit Safari. Hold down the SHIFT key, and then restart it. The SHIFT key tells Safari don't not to load the previous sites.

• Re: Satellite A665-11Z - blue screen problems and stop abrupt

  Hello

  I'm having these problems recently. but I do not know why, or what is the cause!

  Sometimes, I have a sudden shut down, even if the battery is charging.

  also, I get the blue screen issue! & After restarting the laptop, I get this:

  It's in Arabic xD... I hope someone will understand!... the title says that windows recovered in one abrupt stop down! : P

  
  
  

  I don't know much about computers, so I hope that somwone could troubleshoot >.<>

  Thank you: 3

  Hello

  Unfortunately I do not understand what is written on these messages, but for better understanding, you should provide more info on this strange issue.

  Since when you noticed this behavior?
  Can this be related to installing some software, install updates or any other similar action?
  Does this happen when you do specific things on your laptop (open some software, some game)?

  Have you tried to do something about it?

• Satellite L550D - 10G - blue screen daily

  Hi all

  My 4 weeks new L550D - 10G everyday's a blue screen crash! After the crash, I got this information:
  BCCode: d1
  BCP1: 0000000006D9A318
  BCP2: 000000000000000B
  BCP3: 0000000000000001
  BCeP4: FFFFFA60028299ED

  Anyone has any idea what this means? I have Vista Home Premium 64 bit on my L550D.

  Thanks for the reply.

  Hello

  Firstly it is difficult to say why you're getting a blue screen every day. In most cases these bluescreens correspond to the drivers or hardware.
  If you have updated some drivers and what programs you have exactly? Maybe one of these cause this problem

  In addition, it would be interesting to know what BSOD stop code you get exactly, for example 0 x 000000123.
  For most of the stop codes, you can find help on Microsoft Knowledge Base.

• Qosmio F20 blue screen of death after stop

  Hello

  I get the blue screen of death after a stop on my laptop Qosmio F20.

  The error is IRQ_NOT_LESS_OR_EQUAL.

  I guess that's somehow connected to the tv tuner card.

  I tried to restore the system - not good. After the restoration for some time, it was OK. But then again appeared BSOD.

  Sometimes, it also appears when I connect USB hard drives or even when I insert the DVD disc.
  And for shure every time I stop to laptop.

  Anyone have any ideas?

  Hello

  This is my personal opinion;
  I think it's a memory problem!

  Why, because it of very difficult to reproduce this error message and it looks like this BSOD happens without the use of hardware or special software

  I have gogoled for this error message and I had a lot of success!
  I read in various forums on this issue, and especially a fault memory has been one reason why the BSOD appeared.

  But someone suggested to disabled the pagefile... Probably, you should check out these tips:
  http://joelmama.com/2006/10/16/Windows-XP-BSOD-error-IRQ_NOT_LESS_OR_EQUAL/

  Good luck

• Satellite A215-S4757 SD card reader does not work correctly

  Hello world

  I have a Toshiba Satellite A215-S4757. I recently had a duo memory stuck in the SD card slot and got out. Now when I insert a card into the laptop shows no signs of reading. I don't know if it is damaged or simply not work (but in Device Manager, it says its fine.) If any of you can help with the problem would be great. Thank you for your time.

  Hello

  If you have inserted a memory stick duo, but how you removed? A point would be to remove the card reader in the device and reinstall it.

  Another chance if you don't have a chance, you must send your machine to a local authorized service partner that should make a hardwarecheckup on your machine. You might find that the nearest using this link:

  http://EU.computers.Toshiba-Europe.com/cgi-bin/ToshibaCSG/generic_content.jsp?service=EU&ID=ASP_SUPPORT

  Give some information about your success.
  Welcome them