Satellite L40 - 17 M - new HARD drive installed, Vista does not work
Hi guys
I installed a new drive hard 500 GB compatible and using the original toshiba product recovery disc, tried to install windows vista
He partitioned the drive and got insofar as the message "starting windows for the first time", and after a minute or two, I got this message...
"Windows Setup cannot configure windows to run on this computer's hard drive.
I tried 3 times with the same result
I am pressuming the recovery disc will perform a new installation on a blank hard drive, advice or suggestions would be greatly appreciated in fact as I have searched high and low on the internet for answers and have had little luck
So using the disk Microsoft Vista has solved your problem?
Tags: Toshiba
Similar Questions
-
Windows XP Home Edition on a HP Pavilion zv5405us notebook PC
Without a cd operation, he begins by saying-
Intel UNDI, PXE - 2.0 (build 082)
Copyright...
For Realtek RTL8139 (X) /8130/ 810 X PCI Fast ethernet controller v2.13 (020326)
PXE - E61: Media test page, check the cable
PXE - MOF: Exit PXE ROM.
And when I boot from the CD of the operating system it is to the point where I choose to install or repair.
So, if I click on one of those who he says...
Setup did not find hard drives installed on your computer.
Setup cannot continue.
I tried replacing the hard drive, but it was always the same thing, so I put the old one back in.
I need to find a way to fix it.
Can anyone help?
Assuming that your laptop was manufactured after 2003, you can try the HP drive diagnostic tool, but it seems that if you have a more serious hardware problem: cable/connector from the hard drive is faulty or the on the motherboard disk controller has failed.
You can see also solve the Start Up and No Boot problems checklist but that probably tells you nothing that you have not already tried.
See also Overview of how the problems when a computer is not Boot or Start Up properly
-
Qosmio G20-108: RAID->; new HARD drive replacement - he does not want to mirror
I have a laptop G20-108. The raid was quite happilly mirroring then Hdd2 failed. I removed the disk dirve and replaced by a new one [seagate 100 GB sata 150], but he does not want to mirror?
The stuff of aide said she should recognize a new hard drive with a context menu? I do not have it, but when you click on the console's hard drive icons both say that they are what they should be, but they are both "affected"? Nine should be disconnected not online? should we not say reconstruction?
I tried pressing the raid button turn off but it wouldn't let me!Help how to leave the raid console know it is a new drive and should rebuild Hdd1?
Hello
For the use of toshiba (stripping or Mirroring) RAID, you must have two identical drives. Your G20-108 model comes with 120 GB (60 + 60), two hard drives. If you bought a 100 GB hard drive, certainly it will not work.Try this, and you will have no problems:
Make sure that the disks are identical; You can use two different brands, if they are the same size and speed, but it's a BAD IDEA, just get two new hard drives, same brand and size and you make life simple.Francisco
-
installed a new hard drive install vista and full custom
I bought a new hard drive for my laptop and I tried several times to re - install windows vista, I have not yet defined a partition, but I don't think that should affect the initial installation. I can get windows installed the first reboot and after it goes to a screen installation complete and remains on for about 20 minutes, after that I get a black screen with a cursor. I'm clueless as to what is the question.
Hello
You can't push Dell by providing Microsoft DVD
but you can ask
all they do is provide you with a way to reinstall vista, they have done
HP is one that you hear about with replacements parts not OEM
This is Dells use this DVD
________________________________________________
or borrow a microsoft vista dvd. not a HP, Acer recovery disk etc
Make sure that you borrow the correct 32-bit or 64-bit microsoft dvd to your computer
they contain all versions of vista
This is the product key that determines which version of vista is installed
http://www.theeldergeek.com/Vista/vista_clean_installation.html
________________________________________
and try the Dell support forums
There have your same problem
-
had to install the new hard drive, windows key does not
My hard drive died in my Inspiron 660. I ordered a new hard drive and a recovery Dell USB key. A recovery key for Windows 8 pro based on my recommended by Dell service tag. I installed the new drive and used the recovery key to install Windows 8 pro. I then used a third-party tool to get the product key from the BIOS. The product key does not work. I wonder if the product key on the BIOS isn't for Windows 8, Windows 8 pro. If so, the wrong recovery key recommended by Dell.
What should I do to activate Windows successfully?
Secondly, on my old drive hard, I had upgraded to Windows 10 while he was a free upgrade. How to bring back the free update?
Windows 8, Windows 8.1 and Windows 10 TH1 and TH2 had problems installing specific edition. Your key can be a simple language edition or one with Bing edition and therefore rejected by the installation of the edition of bad media.
Windows 10 TH2 and later all the windows 8.x and 7 OEM keys are treated as Windows 10 keys. Edition installation specific issues have been fixed with Windows 10 RS1. The file .iso Windows 10 RS1 image is covering several editions. It contains all OEM editions and will automatically collect a key Windows 8/8.1/10 UEFI BIOS OEM System Locked Preinstallation and automatically installs the correct edition of Windows 10:
http://dellwindowsreinstallationguide.com/download-Windows-10-OEM-and-retail-ISO/
-
Added raw lun mapped as a new hard drive, but VM does not see it.
ESX 4.0 with two Windows Server 2008 virtual computer running.
Created with SAN volumes and put at the disposal of the ESX host.
I went in with my client vSphere virtual machine settings and added a new hard drive > mapped raw lun, stored with VM, physical and everything seems to set up correctly after hitting good. I also increased the size of the other two disks on this virtual machine. I rebooted the VM and connected to the server to find that he does not see the new drive, or he does not see the new size increases for other readers. I rebooted the host and yet, nothing new.
What have I done wrong? Why these changes are not recognized by the virtual machine?
After the increase in the size of disk or adding new disks, you must go the the VM Windows disk management and resize or format/partition/boot disks.
André
-
Tecra A9: HARD drive write Cache does not work
Hello!
When I try to activate your hard drive write cache, it does not work:
I can check the box and press OK, but when I go back to the dialog box the box is unchecked.
The event log shows a warning: "the driver disabled the write on the device \Device\Harddisk0\DR0 cache.This slows down my laptop. I don't want to work without the write cache.
What can I do?Greetings,
ChristianHello
did restart you your machine after checking the box? Usually, you must first reboot the system when certain changes.
On the other side, you know this microsoft article? You should read:http://support.Microsoft.com/kb/332023
This could probably explain why windows leaves the box unchecked...
Welcome them
-
Pavillion 2132tx g6: Ralink wifi driver installed but does not work in my hp Pavilion g6
My wi fi connection worked properly. But when I reinstall the ralink wifi driver, then the driver is installed but does not appear any wireless device. In Device Manager, it says sign exclaimation. How can I solve this problem?
Hi Raj1813,
Uninstall the driver that you installed, download & install 1 of these drivers in place: Intel Wireless drivers for Microsoft Windows 7, Ralink 802.11 b/g/n WiFi Adapter
AFTER THE INSTALLATION OF ANY KIND OF DRIVERS, RESTART YOUR COMPUTER FOR DRIVERS TO WORK ON YOUR COMPUTER.
Yours faithfully,
Ryan
-
New HARD drive installed Vista 32 bit, but need drivers for Satellite Pro A300-1MC
"Because my recovery disks that I made 3 years ago does not, I just installed Vista 32 bit and then on the Toshiba site, where I have downloaded all the drivers available for my laptop (a Satellite Pro A300-1MC) on a USB key (that I don't have a driver to connect to broadband on my laptop) and when I tried to open on my laptop a message comes up saying" Please insert the last disk of all selfextracting and click OK to continue. "
So what I do now?
Thank youSounds like you have enabled autoplay
Whenever you insert the memory key USB flash it will try and read the contents of the files on it.
You can disable this by holding SHIFT when you insert the USB key.
This should disable the AutoPlay option.
Then you can go to MY computer in order to access the USB key.Note: pilots are zipped so you will need to decompress the content first, I installed a 3rd third party tool called WinRAR to unpack the packages unique.
-
New hard drive installed Vista Ultimate, now I can not install my printer - why?
Computer Dell laptop hard drive replaced (warranty) with Vista Ultimate, I installed Office 2007 Professional disc 1 fine, windows update is fine, but I cannot complete the installation for my Kodak printer disc. Has been given the Internet to install via the internet address - link doesn't work either - drive flashing green bar "installation preparation" then nothing? Link Web shows 'Preparing to install' with a full bar green - then stuck there. A few minutes later, he disappears. Never installed. Do not open the drive or cross the bar - never open the Green window to install. Support Kodak decided that I was missing the .net on pre-installed OS HDD framework files. Enough of 3.45 and 4. Is this correct? Do I need previous versions, or something else is the cause. How can I check to see that all the files are correct and understand WHY I can not INSTALL MY PRINTER?
Until the hard disk, memory & the keyboard have been replaced by the Dell tech, I had installed and printed on this Kodak printer for 9-12 months. Suggestions welcome.
Hi LSMama,
(1) you get an error message?
(2) what is the model number of your printer?
There could be several causes for this problem, try the following steps:
Step 1: Run the troubleshooter printer available in the link below and then check
Solve printer problems
http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-printer-problems
Step 2: Clean boot the computer and then try to install the printer
Follow step 1 in the link below,
How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7Important: n ' forget not to put the computer to a normal startup follow step 7 in the link.
Thank you, and in what concerns:
Ajay K
Microsoft Answers Support Engineer
*************************************************************************** -
After replacing my hard drive, Windows Vista does not accept my product key.
product key for Windows Vista
I recently had my hard drive replaced, windows asks now windows vista activation key product but will not accept the key on the label? Ive tried everything but can't accept and follow my last day.
The product Id in the registry is not that of a my label and the pc will not accept either
The laptop came pre installed with vista home premium,
What happens when my time expires and how can they only activate?
Sidwright,
I don't advise borrowing software is not legal.
http://www.Microsoft.com/piracy/MPA.aspx
Try this instead and explain your situation to a live person.
1 / click on the Start button.
2 / in the Search box type: slui.exe 4 and press enter.
3 / in the find window available for activation phone number, select the nearest location where you lie in the location box. You can click the arrow to the right of the location box to expand your choice of venues.
4 / once you have selected your location, click Next.
5 / If the user account control box, click continue or, if you are not the administrator, type in the username and password for permission to continue.
6 / the window Activate Windows now will appear indicating the phone number you are dealing with a series of installation identification numbers.
7 / now compose the activation number is displayed on the screen. The phone number is free of charge (telephone), unless otherwise stated.
8 / you understand that, initially, the line of Activation is Automatic, so you will be asked to enter the numbers displayed on your screen using your telephone keypad.
9 / once the numbers entered via the keypad of your phone, the automated service will issue you with another set of numbers that you Type in the dialog box that is displayed on your computer screen.
10 / now you must follow the instructions issued by the automated service to activate your copy.
11 / if, after going through this process, the activation service informs you that the product cannot be activated and then DO NOT slam the phone down in rage. Rather STAY ON THE LINE and your call will be transferred to an Activation of the device, in other words, someone real who will help you to activate your copy of Windows Vista.
12 / I am aware that these steps can be a pain, but nine times out of ten, Activation is automatic and can be accomplished quite easily on the internet. This is the reason why the service is automated. It is true that sometimes the automatism cannot stop, and when this happens, you are put through to someone who can help you.
-
my hard drive does not, makes the noise, and I don't see in my computer...
a disk is locked using bitlocker... I go to repair hard disk...but I'm afraid that my data in the bitlocker drive safe? No one can access without password?and what happens if the hdd is irreparable? I will come back my data?its working fine now I have clean the power cable from the HARD drive... now my drive HARD works very well... I thank all for answer now, I know the work of the bit locker
-
Pre-installed Vista does not work on my laptop
Hello
I have a new Toshiba laptop with pre-installed Vista Home Premium. It works just completely.
My daughter bought it for me from PC World in the United Kingdom and I live in Guernsey.
All the options of what I do now, as right now I have a laptop unusable.I'm partially blind and need a computer to function well.
Hi Denise
Have you tried to use the Toshiba Recovery CD and reinstall the entire operating system?
You should do this.On this way you might know if it s a hardware or software problem
If the laptop will not properly work after reinstalling the operating system from the recovery CD Toshiba then it could probably be a hardware problem.
If hardware laptop s malfunctioning it s necessary to contact the service provider authorized in your country. Technicians could check all components of the laptop and can locate the fault.
Good luck Denise
-
Tecra A8 - HARD drive Protection service does not work under Vista
Hello
After Vista installation professional in my Service for the Protection of the drive HARD A8 - 185 has stopped working, I need to update the software HDD P.S. Shock Sensor but can not find anywhere.Someone knows how to fix this? Help me please :( Thank you.
Please do not post twice! And you follow the first thread
https://Forum.Toshiba.EU/showthread.php?20349 -
Satellite P100-197: Geforce GO 7600 driver update - games does not work
Hello
Y at - it a update for the graphics card that goes with my satellite p100 - 197? I had a lot of problem with most of the games. They do not initiate.
Hello
If you check this topic http://forums.computers.toshiba-europe.com/forums/thread.jspa?threadID=17091 you will see that Shane has problem with World of Warcraft.
Sorry I have to ask you once again: you have a problem with the games launch or installation?
Maybe you are looking for
-
Hello I have a problem with my iPhone running iOS 10.0.1. New keyboard clicking is barely audible in comparison to his previous in iOS 9. I have all my volume settings set up, everything else is hard, but keyboard clicks are still too quiet. Thank yo
-
When I reinstall the old version, it works fine, but when I update it to the latest version it will stop working, that nothing happens when I click it
-
My experience with Satellite U300 after zapping Vista
Hi all New to the forum but I would like to share my re-love of my laptop computer with you all. First of all, I'm a big fan of Toshiba. My wife has one and after several bad experiences with cheap laptop, I decided to splash out on a Qosmio, a few y
-
New music/playlists appearing is not on the Apple music
This has happened for the last month or two... my Itunes and Iphone 5s are both updated. I used to be able to create playlists of music on iTunes and short while later he would automatically show on Apple music on my phone. Same thing with the music
-
I get error 7 when you try to run the Open Handle LabVIEW HTTP. LabVIEW HTTP functions are supported by Linux of LabVIEW RT? the screws are locked, I don't see how they are implemented.