Satellite M30 starts without activity LCD and HARD drive

The laptop LCD screen is blacked out to color and off suddenly while working normally.
Now when I turn on the switch it starts but not display anything on the LCD screen and the hard drive activity indicator is also off.

I went to the external display, but it did not work also. What is the problem?

Hey Buddy,

Looks like a hardware malfunction if t, you can start your laptop and an external monitor doesn't show a picture too :(

You must contact an authorized service provider. Guys can diagnose your laptop and fix it. Best to help you and here you can find one:
http://EU.computers.Toshiba-Europe.com > support & downloads > find an authorized service provider

Good luck! :)

Tags: Toshiba

Similar Questions

  • Upgrade to a Satellite 1805-514 with a CPU and HARD drive

    Hello

    Several years ago I bought the laptop mentioned above. Unfortunately, the laptop no longer starts because of a damaged hard drive.
    Now I'm looking for a replacement. My dealer offered me several hard disks with a capacity of 40 GB to 80 GB. 1805-514 does support large hard drives?

    In addition my dealer gave me a 1, 13ghz Pentium 3 mobile. Does make sense to replace a processor 1 Ghz Celeron with a 1, 13 Ghz P3?

    Thanks in advance and sorry for my bad English

    Samson74

    Hello

    In my opinion, it makes no sense to upgrade the processor 1 GHz to 1.13 GHz to form
    The difference between these two processors is not high and you have no sensation of the increase in the performance of the laptop.

    I put t know compatible hard drives for Satellite 1805 but for Satellite 1800. But these two units are very similar.
    As far as I know, you can use the 10 GB, 15 GB, 20 GB and 30 GB.
    I think that the BIOS will not recognize the larger HARD drive.

  • Satellite A50: Question about type RAM and HARD drive

    Anyone out there who would try to open their laptop Toshiba Satellite A50, what type of RAM and hard disk of brand you all have inside?
    All the portable toshiba comes with Toshiba RAM and hard drive?

    Hello

    As far as I know the Satellite A50 uses DDR PC2700 modules. These modules must be compatible:
    PC2700 256 MB (PA3311U - 1 M 25)
    PC2700 512 MB (PA3312U - 1 M 51)
    1024MO PC2700 (PA3313U-1M1G)

    There are different models of Satellite A50, but I think that there should be a drive HARD IDE(ATA-6) 60 GB 4200 RPM with 8 MB buffer size.

    Here is all the information I found.

  • Satellite T110-121 - Question about disk and hard drive recovery

    Hello

    I started to use my nice new Satellite T110-12. How can I create a recovery disc?

    Why is there that a common message on the vibration has been detected, HDD head has been moved to a safe position? Is there something wrong? I would return it before the week is up?

    Please answer, thanks a lot a lot!

    Hi LindaMon,

    > How to create a recovery disk?
    What about reading your user manual?
    You need a 8 GB USB key for the creation of a support recovery and preinstalled Toshiba Recovery Disk Creator.

    > head drive has been moved to a safe position?
    Yes, that's normal and everything is ok with your laptop. Your HARD drive will be protected by HDD/SSD Alert utility which is a nice feature of Toshiba to avoid accidents of the head and can improve the lives of the internal HARD disk.
    But yoou can disable these notifications if you want. ;)

  • Satellite Pro L450 - 17K - expandability RAM and HARD drive

    Can someone help me find out what the actual amount of system ram memory can be installed using windows 7 64 bit? As far as I can tell it is 4 GB or more? What is "more"?

    What of the hard disk, what is the maximum size that I am able to install and for which type such as sata etc.

    According to specification notebok your ant Satellite Prohas Mobile Intel GL40 Express Chipset it can handle with 4 GB RAM max.
    Unfortunately there is no specific info on the upgrade of the HARD drive, but it is SATA HDD, which means up to 400 or even 500 GB should not be a problem.

    I advise you to buy a 300 GB HARD drive and I think it will be more tan enough to upgrade the HARD drive.
    What do you think?

  • Cursor flashing at the start of the system and hard drive not working do not on the other computer

    Original title: I need help with my Hardrive

    Recently I had problems with a hard disk of computers. So I'm going to give guys the full story, I fell on this computer, it's actually my mums computer and it had a blue screen at startup error. I'm sorry, but I don't remember that the error was called on the top of my head, basiclly I quikly searched online and alll they say should use fixboot. So I did and the computer booted Windows XP very well. So the next day, when I was starting the machine (just to let you know, it would be the first start since I used fixboot, other than the right after that, I don't know if it would make a difference).

    In any case, while trying to start, there was just a slider, or as underscore that retain just flashing in top left corner. I thought that maybe I should reinstall windows on another partition so my files would be safe. I did it, the installation program had no problem with it, but when I booted up I got the same line of flashing underscore / cursor in the upper left corner.

    I thought that maybe I should back up the hard drive using my other computer so I tried to plug in the hardrive in my work computer and the hardrive started to heat up and as if it worked but any hardrive was getting into my computer, I refreshed it, started the computer upward once again, nothing.

    So my question is what is the problem with this hardrive and how I save? I'm ready to do anything, use the live CD, using another computer. I have precious moments of family on the hardrive.

    Thank you guys

    Hi Joemost,

    As you have important data on the hard drive. We recommend that you contact the vendor of hard drive to diagnose hard drive or visit the nearest tech store to save your data.

    There are chances that the boot files are missing on the computer and also you could have not connected the hard drive as a slave when you connected to the other computer. Once you have saved the data, you can repair the existing windows and check if it starts successfully.

    Try these steps to repair install Windows XP:
    a. start the computer using the XP CD. You may need to change the boot order in the BIOS OF THE system for the CD starts before the hard drive.
    b. on the "Welcome" screen, press ENTER to start the installation of Windows.
    c. accept the license agreement and Windows will search for existing installations of Windows.
    d. Select the XP installation you want to repair in the list, press R to start the repair.
    e. the installation program copies the necessary files to the hard disk and restart.  Do not press any key to boot from CD when the message appears. Setup will continue as if it were a clean install, but your applications and settings are preserved.
    f. when the installation is complete, check if Windows starts correctly.

    Visit our Microsoft answers feedback Forum and let us know what you think.

  • Satellite L555 - 10M - deleted Partition D and HARD drive recovery

    Hi all

    I deleted my D partition on my laptop also drive HARD recovery. Now my Question is how to retrieve an Image on this Partition? I have a recovery CD and I can start it but it s only a picture for Windows 7 32 bit.
    If I boot from CD then a warning appears, who asked if I have already created an Image. If I click Next, then it will format my C Partition.

    Can someone tell me how I can create a new Image without C format?

    Thank you very much

    Hi hardpoekel,

    Why you deleted the D partition if you didn't create the Toshiba Recovery disk? Sorry, I put t understand.

    I think the point is that drive recovery of what you have now only contains an image of Windows 7 32 bit. AFAIK on Satellite L555 - 10 M is Windows 7 64 bit preinstalled and create a recovery for this OS disc, to use the Toshiba Recovery Disk Creator. But now it of too late because you deleted the files on this disc.

    I think that going back to Windows 7 64-bit, you can order a Toshiba Recovery disk:
    https://backupmedia.Toshiba.EU/landing.aspx

    You can use the recovery disk from current 32 bit without any problems, but it will only restore 32-bit version instead 64-bit.

  • I just bought an iphone 6 s second part and I got home put my SIM in there turn it on you try to start the activation process and he says that the phone is lock icloud, I tried calling get him etc. but he gave me the wrong information help please 91026128

    I just bought an iphone 6 s second part and I got home put my SIM in there turn it on you try to start the activation process and he says that the phone is lock icloud, I tried calling get him etc. but he gave me the wrong information and I called apple, they said that its nothing they can do without evidence of perchise im broke I spent all my money on the phone, does anyone know any software free or something me please txt to 9102612856

    @Santonio99

    You probably bought an iPhone stolen 6. Mine was stolen in Barcelona in Spain on June 10 by a pick-pocket. Fortunately, there is absolutely nothing you can do to make an iPhone locked to the activation of the work.  You have a paper weight.

  • Satellite C660 - compatibility between motherboard and hard drive internal

    Hi, I have a problem with the compatibility between the internal (1 terabyte) hard drive and installing windows 7 pro.
    I broke my old internal hard drive (320 GB) and I bought the new hd (1 tb), but during the installation it says that w7 cannot be installed on this new hard drive.

    Can my pc motherboard (serial number: 3B071014k) support the new hard drive (serial number: wd10jpvx)?
    and if the answer is 'yes', how can I make it work?

    First of all the question has nothing to do with the motherboard and HARD drive compatibility.
    If the HARD drive is visible in the BIOS (first page), the HARD drive is supported by the BIOS and HARD disk controller.
    In the case where the drive HARD isn't recognized, you will need to replace this HARD drive with another. I guess the smaller size of the 2.5 SATA HDD THAT would be taken in charge (500 GB)

    However, in case the HARD disk is visible in the BIOS, you should be able to install Windows 7.
    Before starting the installation, you must format the HARD drive and should create the system partition.
    For this procedure, I recommend to use some tools such as partitions for example: GParted
    GParted is a freeware Linux tool.
    You can create a bootable USB key in order to start the device using GParted:
    http://gparted.sourceforge.NET/LiveCD.php

    Then, you should be able to format the HARD disk and create partitions.

  • Satellite L70-A-139 - guaranteed zero when removing the cover for the RAM and HARD drive

    Hi all

    I have a Satellite L70-A-139 youcef.
    And at the back of the laptop, there is a cover that is fixed with a screw.

    Wil I void the warranty when I unscrew and take a look?
    I want to upgrade my HDD to SSD.
    The motherboard supports Sata III: D.

    Thank you!

    No, the mandate must still be valid.
    There is a removable cover at the bottom of the unit as shown here:
    [Toshiba Satellite C70 / C75 / C70D / C75D / L70 / L70t / S70 / HARD S70t drive replacement procedure | http://aps2.toshiba-tro.de/kb0/CRU3703HG0000R01.htm]

    Then you should be able to upgrade the RAM and HARD drive.
    I think this info should be mentioned in the user manual too.

  • A1103 new Ram and HARD drive will not start

    Hello.

    I have a Mac mini A1103. When I got there the folder flashing with question mark. I got a macbook earlier where this problem was solved by installing a new hard drive. so I ordered a new 160 GB IDE 2.5 "5400 RPM and 1 GB Corsair Valueselect DDR1 333 MHz hoping that this will help me get the mini running and preforming a little better with 512 MB of Ram.

    When I boot the mini after swapping ram and hard drive I always see the same flashing folder. I can reset the NVRAM Boot, enter diskmode target? (I think) and the Boot Manager.

    When I enter the Boot Manager I can see the following screen

    a few times I get to this screen for Open Firmware screen where I can use certain commands such as vram-reset reset-all rebot and so, but sometimes I'm just stuck on this screen.

    Anyone have any suggestions on what is wrong and what I can try next? I do not have the boot original dvd but I have a usb bootable with IOS 10.6 and a dvd with IOS 10.6 (not original) but I can't get botting from any of the devices.

    A Mac Mini A1103 has a G4 Power PC processor and cannot be greater than 10.5.8. Superior OSX versions require an Intel processor.

    In this statement "a usb bootable with IOS 10.6 and a dvd with IOS 10.6 (not original)" I think you mean OSX, not of iOS. You must obtain a copy of the original installation disc which was 10.3 or 10.4 or disk to upgrade to 10.4 or 10.5 full retail. Coverall A1103 all three 2005 models of the Mac Mini G4.

    You cannot use a grey disc unless it was delivered with your specific Mac.  Native gray disc with Macs and can not e used on the other model of disc.

    You can probably call Apple and order a copy of the original disks

  • Re: Can I repair the operating system without resetting the whole HARD drive?

    I have a Toshiba Satellite M50, I ran an antivirus in safe mode scan today and must have accidentally deleted a file system because now I can not connect.
    The computer will start but when I try to log in it connect, flash back, my office to the floor once and then connect again.
    I can repair the operating system without resetting the entire hard drive and lose all my files?

    And if not, is there someway to initiate a prompt BACK because I don't that the file is still in the recycling bin, and I might be able to restore it.

    Hello Bambi

    Repair option with the recovery DVD (image recovery) is not available. Using recovery DVDs, you can install OS and have once again the factory settings.
    As far as I know at the BACK level, you can start using BACK discus. You can create bootable CDs.

    You can start your computer in Mode safe?

  • Satellite A210-171 - maximum capacity of a hard drive?

    What is the max HDD capacity satellite a210-171 may take?

    Hi turboiwan,

    As much I know satellite A210-171 has already interface SATA HARD drive so that you can install each HARD drive with this interface because the standard SATA are without capacity limits. This means that hard drives of 500 GB or more may work.

    For example, I upgraded my laptop with 500 GB Western Digital drive HARD and this worked great.

  • Satellite 1410 714 extremely slow after replacing HARD drive

    Hello

    I have a Satellite 1410-714 which has had a hard drive failure. I replaced the drive, but now the computer is extremely slow. Windows has been reinstalled, it was really slow too much and now it takes minutes for windows to start.

    I suspect that something might have broken on the motherboard and the hard disk. I checked mobo replacement parts, but have not found anything for-714, so a 1410 mobo compatible? This model has a processor celeron 1.8.

    Thanks for help.

    Hannu

    Hello

    I can t think the motherboard is broken after replacing HARD drive.
    I suggest updating the BIOS first. Maybe your old BIOS have a few problems with the most recent HARD drive.
    Please check site driver Toshiba for the latest version of BIOS.

    Have you used any anties Virus applications?

  • Responsible for Vista and works fine for about 2 days now, I get the product in use key try AnotherOne coming soon. I have old MB and HARD drive if that can help prove that I only want to use the key on a single machine.

    As noted, my motherboard has failed.  IDE only AGP CPU core.  Not much use trying to find anotherof those.  Replaced the motherboard with a newer version.  It has SATA, multi core processor, etc.  Processor and HARD drive had to be replaced.

    My Vista home premium 32 bit running on my machine for years.  I loaded it on the upgrade with no problems.  Went to windows update and SP1 and then SP2 and all other windows updates suggest and worked very well, for a few days.

    Now, I get a message that the product key is already used and need to buy AnotherOne coming soon.

    I didn't really want to do.

    Ray

    Diagnostic report (1.9.0027.0):
    -----------------------------------------
    Validation of Windows data-->
    Validation status: genuine
    Validation code: 0
    Code of Validation caching online: 0x0
    Windows product key: *-* - R3PWW - Q9F83-MPGXJ
    Windows product key hash: V0k0X5Bh6bySPjhN3xP0FNlEfXY =
    Windows product ID: 89578-OEM-7359704-12357
    Windows Product ID Type: 3
    Windows license Type: OEM System Builder
    The Windows OS version: 6.0.6002.2.00010300.2.0.003
    ID: {694FC5E9-29B3-4912-BE59-B80F163CD007} (3)
    Admin: Yes
    TestCab: 0x0
    LegitcheckControl ActiveX: Registered, 1.9.42.0
    Signed by: Microsoft
    Product name: Windows Vista (TM) Home Premium
    Architecture: 0x00000000
    Build lab: 6002.vistasp2_gdr.111025 - 0338
    TTS error:
    Validation of diagnosis:
    Resolution state: n/a

    Given Vista WgaER-->
    ThreatID (s): n/a, hr = 0 x 80070002
    Version: N/a, hr = 0 x 80070002

    Windows XP Notifications data-->
    Cached result: n/a, hr = 0 x 80070002
    File: No.
    Version: N/a, hr = 0 x 80070002
    WgaTray.exe signed by: n/a, hr = 0 x 80070002
    WgaLogon.dll signed by: n/a, hr = 0 x 80070002

    OGA Notifications data-->
    Cached result: n/a, hr = 0 x 80070002
    Version: N/a, hr = 0 x 80070002
    OGAExec.exe signed by: n/a, hr = 0 x 80070002
    OGAAddin.dll signed by: n/a, hr = 0 x 80070002

    OGA data-->
    Office status: 109 n/a
    OGA Version: N/a, 0 x 80070002
    Signed by: n/a, hr = 0 x 80070002
    Office Diagnostics: 025D1FF3-364-80041010_025D1FF3-229-80041010_025D1FF3-230-1_025D1FF3-517-80040154_025D1FF3-237-80040154_025D1FF3-238-2_025D1FF3-244-80070002_025D1FF3-258-3

    Data browser-->
    Proxy settings: N/A
    User Agent: Mozilla/4.0 (compatible; MSIE 8.0; Win32)
    Default browser: C:\Program may Explorer\iexplore.exe
    Download signed ActiveX controls: fast
    Download unsigned ActiveX controls: disabled
    Run ActiveX controls and plug-ins: allowed
    Initialize and script ActiveX controls not marked as safe: disabled
    Allow the Internet Explorer Webbrowser control scripts: disabled
    Active scripting: allowed
    Recognized ActiveX controls safe for scripting: allowed

    Analysis of file data-->

    Other data-->
    Office details: {694FC5E9-29B3-4912-BE59-B80F163CD007}1.9.0027.06.0.6002.2.00010300.2.0.003x 32*-*-*-*-MPGXJ89578-OEM-7359704-123573S-1-5-21-4094595745-936093891-605987175Gigabyte Technology Co., Ltd.. GA-990FXA-UD3 Award Software International, Inc.. F5 20111013000000.000000 + 000F1303507018400FC04090409Time(GMT-05:00) Standard is03109

    Content Spsys.log: 0 x 80070002

    License data-->
    The software licensing service version: 6.0.6002.18005
    Name: Windows Vista, HomePremium edition
    Description: operating system Windows - Vista, channel OEM_COA_NSLP
    Activation ID: f3acdd3c-119a-4932-a3d7-0b6f33a1dca9
    ID of the application: 55c92734-d682-4d71-983e-d6ec3f16059f
    Extended PID: 89578-00146-597-012357-02-1033-6002.0000-1272012
    Installation ID: 008920048280820090098534504852850165622866742580089774
    Processor certificate URL: http://go.microsoft.com/fwlink/?LinkID=43473
    Machine certificate URL: http://go.microsoft.com/fwlink/?LinkID=43474
    Use license URL: http://go.microsoft.com/fwlink/?LinkID=43476
    Product key certificate URL: http://go.microsoft.com/fwlink/?LinkID=43475
    Partial product key: MPGXJ
    License status: initial grace period
    Time remaining: 36240 minute (s) on (25 day (s))

    Windows Activation Technologies-->
    N/A

    --> HWID data
    Current HWID of Hash: OgAAAAEABgABAAEAAQACAAAAAgABAAEA6GHA7Qx13N/cFZRlVPIQM4gsPm + 8 t/L0Yj1Q1KyJrFYgIQ is

    Activation 1.0 data OEM-->
    N/A

    Activation 2.0 data OEM-->
    BIOS valid for OA 2.0: Yes, but no SLIC table
    Windows marker version: N/A
    OEMID and OEMTableID consistent: n/a
    BIOS information:
    ACPI Table name OEMID value OEMTableID value
    APIC GBT GBTUACPI
    FACP GBT GBTUACPI
    HPET GBT GBTUACPI
    MCFG GBT GBTUACPI
    MSDM GBT GBTUACPI
    CARPET GBT
    TAMG GBT GBT B0
    CARPET GBT
    SSDT AMD POWERNOW

    OEM copies are not transferable between different motherboards.  The license is linked to the mobo mounted.  You are allowed to reagent a mobo replacement of the same make and model, but not an 'upgrade '.  However, you can try to activate by phone.  An agent can help you.

    Activate by phone.  http://TechNet.Microsoft.com/en-us/library/cc736912 (WS.10) .aspx

    Or click Start and type ' slui.exe 4.

Maybe you are looking for

  • How to increase the time-out value for more than 15 seconds?

    Find a web page expires at 15 seconds. I want to set the timeout for a longer period of time. I don't find a place to do this in the Options. When I go to full pages, I want to continue to try more rather than keep hitting the Try Again button.

  • Infra red connection

    Dear Sir, when I try to use my infrared connection with Nokia as modem, I can compose for 3 or 4 minutes, after that a message appears on the taskbar as infrared interrupted and the connection is cut off, I have to start over again and again, please

  • Satellite 1700-200 does not start

    HELLO, I RECENTLY GOT AN ERROR ON MY LAPTOP SATELLITE 1700-200. THE ERROR IS THAT THE MACHINE DOES NOT START IN WINDOWS MILLENNIUM EDITION. IT STOPS RIGHT ON THE SCREEN START AND STAY THERE. I HAVE LEFT IT ALL NIGHT AND CAME BACK TO HIM ON THE SAME S

  • How to configure my live (hotmail) account on my phone?

    I'm a complete amateur when it comes to this kind of stuff. I have an account live [email protected] and am trying to set up on my phone so I can get emails coming through. But I do it every time it fails to connect. I use the settings it provides

  • Cannot install updates (error Code: 80070424)

    I can not download updates, gives me error 80070424