Satellite P10 and so-DIMM DDR400 problem

Similar Questions

• Satellite P10-304 - update Windows 7 problem

  I have a Satellite P10 304 to 2003 which has Windows XP, but I need to update for obvious reasons. I bought a copy of Windows 7 (32 bit) and installed without any installation problem, however I can't update Windows.

  I reinstalled, deleted the hard drive and reinstalled again. Tried the stop and start the Windows Update utility.
  Downloaded the stand-alone Windows Update.

  Updated the BIOS to V2.0 and downloaded the Toshiba Service Station application (who says no update is necessary).
  All this without success.

  My hopes were raised when I saw that the Station Service for Windows 7 32 bit software was available for the P10 304 but I am now at a loss.

  Anyone know if this laptop can be upgraded to Windows 7 and how to get updates of work?

  Help is welcome.

  Peter

  I'm sure that installation of Windows 7 update problems are not specific to Toshiba problems even if you use the Toshiba laptop.

  From my point of few, you should check the Microsoft support pages to find the solution.
  For example this:
  http://Windows.Microsoft.com/en-us/w...#1TC=Windows-7

  Just a tip: I had some problems in the past to install updates because of the antirust software. He locked the installation of some essential updates and after you disable temporal, updates could be installed...
  Missing Service Packs might concern the single installation of patches.

• Satellite P10 and the graphics card driver updates

  Hello

  I'm a newbie on this forum, but let's get to the point. I have Toshiba Satellite PSP10E (PIV 2.8HT 800 Mhz, 1 GB of system memory bus speed and UNFORTUNATELY a GF 5600go...).
  My (not only) problem is that Toshiba use engineering video BIOS version and it does not have the latest drivers for the geforce series. The most up-to-date driver that really works is the last of the series 5xxx... so you can see that none of the newer games can be run with a performance on this map... because older drivers don't use really not (available at directx9.0) 2.0 pixel shader. It would not be a problem if Toshiba would give an update not only BIOS system, but also the bios video (new system BIOS contains the same old video bios.

  I really had to settle for playing games that are 2 years old? First of all pay a lot of money for a witch of the computer has enough power to run some new but don't care support Toshiba for this...

  I was the proud owner of a Toshiba laptop, but I'm not! If I had to choose again, I decide to buy computer Toshiba...
  My Question: is that Toshiba will do something with this problem? Someone knows how to help? Thanks for any help (I have not found such a problem in this forum, sorry if it has been the front sign) and sorry for my English (hope that's understandable)
  My video Bios is: v4.31.20.56.A6

  [Edited by: admin]

  Hello

  We know that you can not install the drivers downloaded from the download page of GF because of the restriction of material. It's not only the Toshiba models, but also on other producers of portable and if you visit the download page of graphics cards, it is always recommended to download drivers designed by the manufacturers of portable.

  I think that nobody can explain why it's because I'm sure you know the reason. The performance of the graphics card will always be a topic of discussion and you will always want to have maximum performance for games with laptop, although performance may not be the same as on the desktop where you have the possibility to change the graphics card and install the latest drivers.

  Because of this, I think that it is really unnecessary to some turbulence here. Believe me, you can buy what you want, but after two or three years you will be always satisfied with something.

  In any case, good luck and enjoy life!

• Satellite A100 and USB audio device problem

  I bought "toneport ux2 line6" and it does not work with my computer laptop (dual core 1, 73GHz, 1 GB ram, Windows Vista).

  The problem is when I listen to music through this device, it looks I would look scratched CD, from time to time that there is a short interruption. The same thing happens when I'm with gearbox (software that allow you to play the electric guitar using audio device). I checked everything, including change Windows XP OS.

  I have the latest drivers for the port of your (compatible vista), I downloaded 3.5 mechanism, only toneport is connected to my computer, I have disabled all installations flashing in vista, power management is scheduled for high performance. I disable the sound card. I checked my cell phone with line6 monkey and it says everything is ok. I checked the audio device on my friend's Office, and it works well.

  I desperately need help.

  Hello Marcin

  In my opinion, you must be sure your laptop running fine and according to your assignment I do not here no problem.

  So in your case you have problem with some additional equipment or third party software. Am I wrong? If there is a problem I see no reason to seek the solution with Toshiba. You should contact the manufacturers of all the devices and software that you use. They should have enough experience with own products and they should offer good support in troubleshooting.

• Satellite P10 and Netgear USB dongle use

  Hello

  NETGEAR insist it is a Toshiba system problem...

  Whenever I try to inslall wg111v2 cherif I get... Failed to install... "RegDBCreateKeyEx failed", and/or... "cannot read the control on the Netgear server file.

  I don't have this problem with my other non-Toshiba Office.

  HM, looks like some related software question, but it s easy for netgear say you it s a problem with toshiba. It is like moving around customers as on a chessboard. :(

  But okay, now you´re here and we all will try to help you. You say you don t get the problem on your machines 'NON-TOSHIBA.

  So, I would say that you should first try to recover your machine with the recovery media, and then try to install the USB dongle. If it really works then it was just a problem of software and it s resolved but if not then come back and we'll see the next today.

  Good bye

• Satellite A205 and 4 GB RAM problem

  Well today I got a new stick of Ram DDR2 2 GB, bringing my total Ram to 4 GB. However, my computer recognizes 3 (3070 MB) to be exact. I am running Windows 7 64 bit. I'm guessing that the issue has to do with * remapping memory in the Bios is enabled * however I do not have this option. I tried to download the latest version of the Bios off toshiba.com, version 5.20, well, it won't work, I tried to do it through Windows, as well as on a CD, I get the error messages.

  So I was wondering should I get the BIOS also? If yes where? My Bios is Phoenix TrustedCore.

  > However my computer does recognize that the 3 (3070 MB) to be exact.
  In the BIOS settings or directed by operating system preinstalled?
  > I am running Windows 7 64 bit. I'm guessing
  Can you please check this and remember what version of the OS is preinstalled on your system?
  > I should get the BIOS also? If yes where?
  Do not play with such things. Use BIOS Toshiba support only page.

• Satellite P10: Discharge battery problem

  Hi all. I just bought a P10 and I have a problem with the battery discharges while remaining on the current after being fully charged.

  Basically when the battery discharge the machine stops and cannot be restarted successfully until about 1/2 hour of charging.

  Surely if the machine is on the battery supply should be go to the opereation of the machine? Virtually all other laptops are not disturbed by the battery then on the sector.

  Is there a utility that disables this problem because there is nothing in the bios that is available to select. (BTW, I HAVE ISNTALLED LATEST VERSION OF THE BIOS).
  I also blew the hole thing with compressed air just in case there was a problem of overheating.

  Am Running XP Pro 512 MB DDR333Mhz 30Gig HDD 2.6 GHz P4

  All this makes me very frustrated and am really starting to regret to have bought the laptop.
  I've been a professional for 10 years now and have never experienced such a problem.

  Any help, advice, links or the fixes would be greatly appreciated so thank you very much in advance.

  Hello

  It s very strange.
  As far as I know the Toshiba power saver control power and cooling procedures.
  If the AC adapter is plugged in, the energy saver uses a profile of full power.
  If the laptop works with battery energy saver must use another profile with different parameters. You should check what profile is used and the settings for this profile.
  Check the CPU and cooling module parameters.

  But if this doesn't help then it could be something wrong with the hardware. But it's not easy to say what the problem is. In this case, you must contact the after-sales Service of Toshiba partner. It can start diagnostic tests.

• Driver WLAN for Satellite P10-540

  Hi friends...? use a satellite p10 540... the problem is any wireless lan driver? cannot install it from cd and the toshiba site... when? try to download it, there is a failure... it says that:

  drver was not updated!
  ? NF file is invalid or incorrect
  ? sntallation failed

  Press the keys to cont? naked...

  That's all folks... Please help me to install the wireless lan driver...
  my email address is [email protected]

  Thanks in advance

  Hello

  If your device comes preinstalled with recovery CD you n t need any update of the driver. Wireless card in Device Manager and reboot the device. After reboot, wireless card should be detected and installed automatically.

  What kind of problem you have with the wireless card?

• Satellite P10 - after installing XP, the SD card reader does not exist

  I formatted my Satellite P10 and complete nine with XP SP1 installed. Since that time the integrated SD card reader no longer exists in the system (when I insert an SD card it doesn't work). Is this a problem with a driver or what can be the problem?

  Before formatting, it's normal. Pleas explain easily. I'm not a professional user.

  Hello

  What drive did you use to reinstall Windows XP? If you use the Toshiba recovery disc are all drivers and pre-installed tools because the disc contains a picture of the factory settings.

  In your case, I would try to install the latest driver for the European driver of Toshiba download page card reader. Maybe it's just a driver problem you s wrote:
  http://EU.computers.Toshiba-Europe.com > support & downloads > download drivers

  I m wondering that you only use the SP1 for XP. SP2 or SP3 new contains a lot of important security updates. I recommend you to update your XP version.

  Welcome them

• Satellite P10: The drive will not burn DVD

  Hope someone can help me,

  I have a Toshiba Satellite P10 and have just received some photos software, burning
  But my drive will not burn DVD, I try with discs DVD - RW which must work my laptop.
  What is happening is when it comes of the burn on the part of the disk of the process he starts, but it fails.

  I tried to burn it with Nero, but even if I burn OK on any CD discs with this software it will not work on DVD discs. It's really annoying because when the burning process it fails so that it makes the DVD - RW disc seem curupt and then my drive has problems mounting the disc to try a deletion once more.

  I have the Nero log file failed
  Done if it's any help to anyone.

  A big thank you Michael.

  Hello

  What about different DVD media? Have you tested the media DVD-R or DVD + R common?
  Have you tried different brands of DVD?
  I can't give you a properly answer why the drive can't burn your DVD - RW, but to my knowledge not every media is supported by the player.
  So I think you should check different DVDs.

• Satellite U500 and fan CPU issue on Ubuntu 9.04

  Hello world

  I just got my Satellite U500 and I had a problem with Linux.
  After grub starts the operating system, my cpu fan turns off and it never turn on more.
  Sometimes when the CPU's heat it just lit for 2 seconds...

  I tried to add "acpi = off" on the line of linux. in /boot/grub/menu.lst
  The fan does not spin.

  Can you guys help me?

  same problem here

  on ubuntu and archlinux fan turn off when linux starts, it is very dangerous for the unit because the fan never turn on

  on archlinux, I can't try acpi_osi = 'Windows 2006' in the grub menu, I don't know if it can help you

  This is the only problem with the U500, it is perfect under windows.

• Satellite P10 TV OUT button does not

  Can someone help me, I recently rebuilt my laptop Satellite P10 and now noticed the TV OUT button on the side right does not work. The OS is XP PRO

  I can use the F5 key, but who want to get this dedicated button works, someone at - it ideas

  See you soon

  Dave

  Hi David,

  When you have rebuilt your laptop you re-install the operating system and all the utilities Toshiba? I think that the button that you are talking about is controlled by the Toshiba EasyKey utility.

  HTH

• Satellite P10 554: what does "removable devices" on average of start menu?

  Hello

  My DVD burner does not work, so I have no chance to install Windows XP from the recovery disks. I tried to boot from external DVD writer, but the device is not recognized. Similarly a bootable USB key.

  That means Toshiba with "removable devices"? Or I made a mistake?

  Thanks for your replies.

  Best regards
  Frank

  As far as I know Satellite P10 and P20 have removable optical drive. You can remove the CD/DVD drive and put it inside the floppy drive and use it as first boot device.

• Satellite P10-304: the problem writing and erasing CD - RW discs

  Some need help pls. I own a Toshiba satellite P10-304 with a combo player SD-R2412 installed. When I try to burn a new CD - RW, it does ok, but wouldn't allow no other written on the same CD in another session. The written CD - RW is then recognized as a CD-ROM. In addition, it is not possible to erase the cd - rw usinig this player. When I take the cd written for my laptop office of deletion, as it's done with success and my toshiba can then burn again. Any ideas on what to do?

  Additional information: laptop computer came bundled with "drag n dro cd" but I had to install Roxio and even tried the cd writing software provided with windows XP are done everything to nothing. I checked the 'advanced system info-error log' and the report there is 'the device, \Device\CdRom0, has a bad block'; I don't know what that means.

  Cheers.

  Nthunderbolt

  Hello

  In my opinion, it's probably caused by software. In my opinion, you should remove all burning software and verify all burning functions with windows option. After deleting some software, it can happen that, in the registry editor it is a lot of waste that will not be removed completely.

  In any case, delete all the burning software, and you can also try to remove the device from Device Manager DVD. Restart the laptop and DVD should be detected and installed correctly. Try using the option of engraving of Windows and if there is still problem writing once again please.

• Satellite P10 371 WiFi problem

  I recently bought a Satellite P10 371, to use on business when away from home and I am a newcomer in the world of networks

  The problem is that I do not get an internet connection. When I start the Configfree physician connectivity, it shows an orange alert triangle between Lan Wireless mini-PCI card and the wireless access point and a status of the cut-off line.

  The Wireless Lan mini PCI card is enabled but WAP disabled.

  While I have no point of access (router) set up in the House, I had to travel to try to get a connection.

  The wireless network settings are for windows set up my wireless network.

  It says under available networks and the box is empty.

  Can someone tell me where I'm wrong? any help on this would be appreciated.

  This does not mean that the box is empty.

  If very simple as possible to configure a router for access to

  Download "invisible" for your machine.

  If you don t have its security requirements.