Satellite P850 - right USB ports stopped working

I have a new P850 Satellite, after a short period, that the two right usb ports stopped working, I had only a wireless mouse connected to them at the time. Is there a reset for these ports, I tried to uninstall and reinstall, no change.

Anyone has any ideas.

> I tried to uninstall and reinstall, no change.
What have you tried to uninstall or reinstall?

Tags: Toshiba

Similar Questions

  • USB ports stopped working unexpectedly

    Hi, I am currently on "Toshiba Satellite C655"run"Windows 7 Home Premium". It's a laptop of 2009 model (2 GB). Last night (24/02/14) my USB Ports stopped working, they have been and continue to read anything every time I have to plug my devices. I usually only connect a cooling block and a USB mouse to the computer. They worked perfectly until I disconnected the. When I reconnect them, they work momentarily, and then I hear the beep sounds when you eject a device. I tried to connect several flashdrives, a printer, and one I tried the following hotfixes:

    Note: The order of numbering has nothing to do with the order, I tried to apply each patch unless specified elsewhere. This computer had Windows 7 Home Premium REINSTALLED at some point. Just for your information. This message was made when there are others with the same problem is due to the fact that no solution not specified by Microsoft Technical Support or the Microsoft community were effective.

    1) System Restore to the last known point, where they worked (and still). (Point restoration @ 15/02/24)

    2) Windows Update

    3) turn off the computer, disconnect the battery and the power supply and holding 'On' button for 10seconds.

    (Note: whenever I turn on the computer now they work only for a moment, usually from 60 to 180 seconds.)

    (4) Start > research ' Device Manager '> "De Bus USB controllers" Expand and turn off and restart the computer. They are re - activate automatically but my problem persists.

    (5) download and run "Microsoft FixIt.WinUSB... ", on the 1st, I had a problem with devices not updated. But I actually watch updates by using Windows Update and ""searching for hardware changes "" on USB Bus controllers "." I then did a 'System Restore' and now Microsoft FixIt found no problem but the USB Ports don't always work.

    (6) will ' services.msc"and change the Startup Type of Manual to Automatic for Windows install and restart Windows."

    7) regedit

    8) sfc/scannow

    I am really lost with this problem now. My laptop works and worked perfectly fine until this problem occurred. I have fixed minor problems with computers before, but this is a bad joke for me now. If someone could please help me with this problem I would appreciate it a lot. Thank you very much.

    Thank you for your help, but I discovered something funny on my computer. My cooling package (product name: Laptop Cooling Pad NSB;) HYCF-6181-2 model number) is to disable my USB ports when I plug. If I leave it unplugged and restart my computer, my USB mouse is still working on a port. Also tried using my USB and other devices. The problem is my block of cooling that strangely disables my USB ports, whenever I plug. Thank you very much for your quick response, fortunately the answer might help me in the future. For now, I have solved my problem.

  • USB ports stop working after windows 7 updates (April 12, 2011)

    After application of the 12 updates successfully (KB890830, KB2508272, KB2506223, KB250212, KB2508429, KB2507618, KB2509553, KB2503658, KB2506014, KB2491683, KB2511455 and KB2446710), my USB ports stopped working after restart. I get this description of Device Manager: Windows cannot verify the digital signature for the drivers required for this device. A recent hardware or software change might be installed a file that is signed incorrectly or damaged, or maybe it's a malicious software from an unknown source. (Code 52)

    I restored the functionality of USB ports by doing a system restore before installing updates.

    What should I do? Ignore ALL updates future windows 7, which leaves the system vulnerable? Help is appreciated thanks.

    I solved this.

    Device-USB controllers-online standard uninstall online Manager pci improved to (do it twice) usb host controller, and then the scanner hardware change and let the win7 to reinstall the drivers.
    Updates were corrupted somehow the drivers, you need to fix manually.
  • All USB ports stopped working Windows 7

    Windows 7 Pro. All USB ports stopped working.  When I plug a usb card, windows makes the sound as it connects and the card gets power (light).  I see the map appear in disk drives in Device Manager.  The player does not display in windows Explorer or disk management.  In Device Manager, it has an exclamation point and says that the device cannot start.

    Strangely, I have a USB keyboard and mouse and they work very well.

    It's just the USB drives and chips and SD cards that are not displayed.

    I have:

    Reinstalled the drivers USB MB

    Flashed the BIOS with the latest version

    Tried to install the older USB drivers

    Tried to let windows find the driver.

    Still does not

    None of this has helped.  I ended up formatting the HD and reinstall windows from dvd.

    This revealed that my USB multicard reader was bad.  When I unplugged the problem disappeared.

  • SQosmio G50 - 10 H - one of the usb ports stopped working

    Hello forum,.

    I have a BOUNCING problem with usb ports on my qosmio g50-10 h.
    There are two ports on the right side of the machine and I have 2 self-powered 7 centers of port (usb 2) attached to these.

    Every now and then to stop it from ports and of course all the parts a unregcognised, not found.
    I get error messages saying unregognised device or usb device stopped working or windows stopped device etc.

    Unplug the hub and repluging it ususally actually come back to life.

    any ideas?

    Stafford

    Hello

    Have you tried to connect devices directly to the USB port?
    Try this and see if the USB device is disconnected, as you mentioned that using the external USB hub.

    Generally speaking, it is difficult to say what might cause this
    You could try updating the chipset driver.
    Of course, you should also check the USB port settings, and power management options for economy.

    In device manager-> USB root & hub-> properties you could disable for unique energy saving USB ports.
    This also on Win 7 power management.

  • Satellite 1900-303 USB port not working - USB hub?

    Hello. Deploy a Satellite 1900-303 with two USB ports. One of the ports stopped working. I guess it's permanently broken. Just browse the site, it seems that the easient of thing to do would be to get a Port Replicator - one of them:

    http://UK.computers.Toshiba-Europe.com/cgi-bin/ToshibaCSG/JSP/individualOptions.do?service=UK&selCategory=4697&o ldCategory = 4697 & OPTION_ID = 95631 & toshibaShop = true & t ab = 1 #1

    I wanted to know is it just to sink my remaining a USB port, so that I get 4 USB ports (and all others)? What USB speed I would get?

    Thank you!

    Rich

    Hello

    As far as I know the unit supports USB 1.1
    So I guess if you are using a USB hub external, USB ports work with USB 1.1 properties.
    Maximum data transfer should be 12 Mbps

  • Satellite L850 - USB Port stopped working

    Hello guys,.

    first sorry for my bad English, im from Germany.

    My new clearly L850 satellite has had some problems with sound-Port USB.
    I think it's the Usb3.0 Port on the left.
    While I'm workin with an external keyboard, the USB Port has stopped working and cannot identify the keyboard.
    All other devices that I put there, are out of order, but when I put an external hard Powerdevice with separate data for laptop, that he is there something ist connectet, but can't identify it.

    I have try all troubleshooting close it, like install new drivers, disable ports and restart and any kind of it.

    So maybe you have another tip for me?
    Or do I have to bring my laptop to the store for warranty?
    A Windows 8 64 bit on it, maybe it will help.

    Best regards, neothic

    Have you tried reinstalling the driver USB 3.0? Please try and check the functionality. If this will not help I recommend you do the ultimate test: back up all your data and reinstall Win8 using recovery media. Test it with clean OS preinstalled and factory settings.

    In the worst cases, you should contact the nearest Toshiba service provider and ask for help.

  • Satellite A200 - USB Ports stopped working

    Hallo, I am DESPERATE for help, please.

    I have a Toshiba laptop Satellite A200 series with 32-bit Windows.

    My USB ports give me major problems.

    I use a USB Internet Modem on multiple computers and it works fine on all computers, including Toshiba.

    A month earlier, Internet USB would suddenly and constantly disconnect itself from the Internet, when I use it in the USB one. When I use USB port two, he recorded no more. The port does not have the device.

    Two USB ports work well when used by other USB products.

    I had always used Internet USB into the USB port, with a cooling for my laptop fan, USB 2 port. Now, when I insert the cooling fan, USB Internet disconnects and will not register, at least I have remove fan, remove and reinsert the USB Internet.

    I did the following:

    1. start an anti-virus
    2 uninstall, re-install and update all the drivers for the USB, chipset famlies, Internet Modem ports, EVERYTHING.
    3. I checked with my Internet provider, the problem lies in my PC, not them.

    I don't know what to do, I'm tired.

    Help, please!

    Now, when I insert the cooling fan, USB Internet disconnects and will not register, at least I have remove fan, remove and reinsert the USB Internet.

    I think that it is a problem of USB power.

    The USB 2.0 port provides 500mA, and in some cases more than USB ports can be connected to the same power supply to the motherboard.
    In case the USB device connected (in your case fan) would need more than 500 ma, it could be that other USB devices do not work correctly.
    I recommend you go to Device Manager and select the properties of USB controller.

    The last "Power Management" tab contains the option to turn off the device to save power.
    This option should NOT be checked. It should be disabled.

    Check it out.

  • USB PORTS STOPPED WORKING

    My USB ports for Entertainment of HP Pavilion laptop dv7-2277 cl stopped working.  I tried to update to Windows, since before system restore and still no luck.  the port on the left side of the laptop shown peripheral unknown whenever I plug anything in there and nothing does.  the two ports on the side right are nothing at all.  The indicated device MGR I use the current drivers, but he doesn't know what I use in the car.  I tried 3 different mouse and ACC Player.  This seemed to happed after that March 11, 2014 Windows update or after plugging in headphones NXG technology to charge the battery.  NXG assures me that they are not the problem and their agenda only charges the battery of the power from the USB port.  Ports due light ACC Player or headphones indicating the power is in them.  I'm stuck and have no idea what else to do.  Please help if possible.  Thank you for reading and taking the time to listen.

    My computer is now fixed and I'm superised that nobody else on this forum had the same problem.

    Microsoft just send a new update for USB mouse and if ports pointers fixed my question on all my USB.

    HAPPY CAMPER!

    See you soon!

  • My USB ports stopped working

    My USB ports just stopped working all of a sudden. For this reason, I can't print, download images, load my i - pod, etc.. What can I do to fix this and get my ports working again?

    Hello

    Check the configuration/settings (BIOS/CMOS) often F2 when you start - make sure that USB is enabled.

    If a PC and if necessary the embedded USB can be disabled and a USB card can be used only
    is not expensive. For a laptop, using a real computer shop (no leeks and glances at a Best Buy
    or other stores) or system manufacturer support.

    ------------------

    Follow these steps to remove corruption and missing/damaged file system repair or replacement.

    Run DiskCleanup - start - all programs - Accessories - System Tools - Disk Cleanup

    Start - type in the search box - find command top - RIGHT CLICK – RUN AS ADMIN

    sfc/scannow

    How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
    generates in Windows Vista cbs.log
    http://support.Microsoft.com/kb/928228

    Then, run checkdisk - schedule it to run at next boot, then apply OK your way out, then restart.

    How to run the check disk at startup in Vista
    http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

    -----------------------------------------------

    Then lets refresh the USB stack

    Control the click Control Panel - Device Manager - no matter where in the box of white/white - then the VIEW - see the
    Devices disabled - look around (with the exception of USB controllers) for your devices (can have
    zero or more than one) and top - right click UNINSTALL.

    Control Panel - right CLICK on EVERYTHING - Serial USB controllers - Device Manager and UNINSTALL
    all except the category itself - REBOOT - it refreshes the drive and battery USB

    This KB shows XP how to and the method of Vista is identical
    http://support.Microsoft.com/kb/310575

    This is a utility to help you, but do 1 above.

    USBDeview is a small utility that lists all USB devices currently connected to your computer, thus
    as all USB devices that you previously used. Run Options and check the 1st three choices to see to it there
    Is there.

    http://www.NirSoft.NET/utils/usb_devices_view.html

    You must remove all instances of the devices and restart.

    ----------------------------------------------

    If necessary try these two:

    Tips for solving problems of USB devices - and a Mr Fixit
    http://windowshelp.Microsoft.com/Windows/en-us/help/c39bd203-f729-47a4-8351-83291e13c8a81033.mspx#EGB

    Hardware devices not detected or not working - Mr. Fixit
    http://support.Microsoft.com/GP/hardware_device_problems

    ==========================================

    If you have tried ALL the foregoing Installation of upgrade/repair in Place could help. This allows you to keep
    programs and data backups however redundant are always a good idea. (It is less likely to help
    If you have not tried all the above methods as the same parameters and conditions exist).

    You can use another DVD that aren't copy protected but you you need to own
    Product key. It must be the same version 32 or 64 BIT Vista OEM. Also the system
    machine to usually sell the cheap disk since you already own Windows. Don't forget to make a
    good backup or 3 (security in redundancy).

    On-site upgrade
    http://vistasupport.MVPs.org/repair_a_vista_installation_using_the_upgrade_option_of_the_vista_dvd.htm

    This tells you how to access the System Recovery Options and/or a Vista DVD
    http://Windows.Microsoft.com/en-us/Windows-Vista/what-happened-to-the-recovery-console

    How to perform a repair for Vista Installation
    http://www.Vistax64.com/tutorials/88236-repair-install-Vista.html

    I hope this helps.

  • Windows Vista - why my usb ports stopped working, and how do I fix them?

    My 3 usb ports worked very well, but a few days ago they just stop working.  I updated the drivers even though my drivers were already later.  I even tried to update the drivers.  Nothing seems to work.  Can you help me?

    Hi WillisPop,

    ·         Since when are you facing this problem?

    ·         You did it last changes before the show?

    Use Device Manager to disable and re-enable all the USB controllers

    This allows controllers to recover the port USB of his condition does not respond. USB controllers represent the USB ports in Device Manager.

    To disable and re-enable the USB controllers, follow these steps:

    1. click on Start, type Device Manager in the start search box and press ENTER.

    2. expand Universal Serial Bus controllers.

    Note: you may scroll through the list to find this point.

    3. right click on the first USB controller under Bus USB controllersand then click Uninstall to remove it.

    4. repeat the above steps for each controller USB is listed under Bus USB controllers.

    5 restart the computer. After the computer starts, Windows will automatically check for changes on the hardware and reinstall all USB controllers that you uninstalled.

    6. check the USB device to see if it works.

    You can also check out the article below for more information:

    Tips for solving problems of USB devices

    http://Windows.Microsoft.com/en-in/Windows-Vista/tips-for-solving-problems-with-USB-devices

  • Two of my USB ports stopped working (wired mouse and iPhone do not respond). What should I do?

    I have a laptop Toshiba Windows 7 which has two USB ports, which both have stopped work or respond. They were both working an hour ago and I made no changes to the computer. I have a wired mouse connected to one of the USB ports and my iPhone plugged in with a USB cable. The mouse is not responding and my iPhone is not being detected or charged. What should I do?

    Hello

    1. do you think that no matter what error code in Device Manager?

    2. you are trying to connect other USB devices to the USB port and check if it is detected?

    3. have you rebooted the system to see if they start working?

    Method 1:

    Follow the link below, run the fix it tool and check if it helps.

    Hardware devices do not work or are not detected in Windows

    http://support.Microsoft.com/mats/hardware_device_problems/en-us

    Method 2: Remove and reinstall all USB controllers

    To remove and reinstall all USB controllers, follow these steps:

    1. click on Start, type Device Manager in the start search box, and then press ENTER.

    2. in Device Manager, click the Hardware tab,

    3. expand Bus USB controllers.

    4 right-click every device under the Bus USB controllers node and then click Uninstall to remove them one at a time.

    5. restart the computer, and then reinstall the USB controllers.

    6. connect the removable USB storage device and perform a test to ensure that the problem is solved.

    Let us know if it helps.

  • Satellite M30-106: USB Ports not working not

    Hello.

    I have a problem with my Satellite M30-106. One day, the system froze (Windows XP with SP2) during the passage of the machine off. I was forced to keep the button "power" for a while in order to close the system. However, since all 3 USB ports do not work.

    The system does not recognize the "" them. I can't see in Device Manager. I tried to reinstall the system, but it did not help.

    Can someone help me, pelase =)

    Hello

    It looks like a hardware problem. At whatever it is connected to the USB ports at the time? Could you check the USB ports visually and see if they are damaged or wobbly. It is a bit of a long shot, but you may have a short circuit decision and which could disable the USB.
    If the motherboard is damaged then outside fixing/replace your only option would be a PCMCIA USB card, they are not expensive.

    Best regards
    Swarvek

  • all 3 USB ports stopped working - MX30

    As a result, none of the 3 USB ports on my old MX30 work of 2 months. I unchecked the option in the hardware Manager of devices for energy saving, nothing helps. First of all, only the mouse stopped and I thought the mouse was to blame, but all of a sudden the machine does not recognize the USB memory key more.
    Any advice would be very welcome, because I can't work!

    Respond to my ad. I've updated the drivers for the USB host controller and BIOS and USB ports running again.

  • Re: Satellite P850 - 12 X completely stopped working

    I can't give info much more than that, but my computer has just stopped working.

    I had owned the PC for less 2 hours, but while I was installing some programs the computer will just empty. It seems to be quite dead.

    It fails to turn on, the light indicating it is connected is not yet lit.

    I have no idea what could be wrong or what caused it to stop just but it is rather relative. The only thing I can say is he was running rather hot, I never expected to get so hot, but I assumed it was normal given the processor, it is running.

    An hour after initially breaks I tried to turn it on again, but nothing helped. Does anyone have and suggestions/recommendations for my next course of action?

    Post edited by: aclarke91

    Change P850-12Z P850-12 x

    You are right. Ask for the replacement of the laptop. I hope that you will get a new.

Maybe you are looking for

  • service delivery in Ukraine

    Hello. Anyone know how to get support in Ukraine? My iPhone 4 is locked and I have no other (Russian or Polish phone # to get the call to a public support)

  • TP8 - Win10 Build 10586 - Flight Mode 'problem '.

    Since having upgrade 10586 build Win10 professional, I meet the following phenomenon: After the start of the system, the 'flight' Mode - button lights up blue, although the flight mode is not enabled, see photo. Everyone had the same experience with

  • Should I save even if I do not need my personal files?

    Basically, the title says it all. When formatting the hard disk, is a return to the top a must , even if I have personal files, I have anymore?

  • Problem with IRQ Ethernet q150

    I'm trying to use an IdeaCenter Q150-40813AU with Linux (Centos 5.5) However, I have an IRQ error at startup which generates the temporarily unavailable "SIOCSIFFLAGS resources" message when you try to load the network driver. I tried the Plug n Play

  • Pavillion P077tx: Compatible drivers Windows 10

    I am currently using windows 10 and windows oem 8.1 drivers do not work properly here. When hp will provide compatible drivers for windows 10. I have tired downgrading to windows 8.1 only because drivers incompatible