Satellite Pro M10 cannot start properly - AC LED flashing orange

Similar Questions

• Satellite Pro M10: Cannot get a resolution of 1680 x 1050 px

  Hello

  Recently I have bougth a screen Dell 2005FPW with a native resolution of 1680 x 1050.
  With the standarddrivers of the geforce4 420 go in my satellite pro m10, I can't get this resolution (max 1280 x 1024).
  How can I solve this problem and work to the full capacity of my screen?

  Hello Jorré

  Sorry, but I don't see any problem. The fact is that there is a restriction of the graphics card and if the max resolution is 1280 x 1024 you cannot set upward for external LCD.

  Maybe you can try with something like this http://eshop.macsales.com/item/Viewsonic/VTBOOK/

  Good bye

• Satellite Pro M200 - cannot start Windows

  I have a Satellite Pro M200 PSMC4A, did an update Windows, requsted to restart, then the black screen as follows:
  Windows could not start. A recent hardware or software change might be the cause. Equip the installtion disk and restart. Problem 1: having no disk - lost I think. Lost file is \Boot\BCD.

  Tried different legal remedies without success. Disk Windows XP used to reinstall but now says cannot see all hard drives!
  All of the suggestions.

  Hello

  You can access the advanced boot menu? If so, you should try to start in charge more than the last known good configuration.
  If this is not the only option is to reinstall Windows I think. Therefore, you can take a Microsoft or Toshiba drive. If you don t have the Toshiba disk recovery, contact the service provider authorized in your country.

  I think that the recognized HARD wasn t disc because you need SATA drivers. Did you check that?

• Satellite Pro A120 cannot start when the printer is connected

  Hi I have a brand new Toshiba Satellite Pro A120 but I'm having a very strange problem.

  I installed my printer - Epson Stylus Photo R300, but now the laptop will not start if the printer is on. When I turn it on the Toshiba screen comes ok, then the Windows XP screen comes with the black background when the blue bar to cross to load Windows but its all disappear and the laptop just hangs and will not!

  However, if you turn the printer off and turn the laptop it starts up fine!

  Its really the printer which is the cause as its only when I turned it on.

  It's never caused this problem with my old PC using Windows XP too.

  Any help with a resolution would be greatly appreicated.

  Thank you

  Adam.

  How to disconnect the printer during the boot process? ;)

• Satellite Pro C650 - cannot start Windows more

  I have a Toshiba Satellite Pro C650 11Z model under Windows 7 Home Premium. I'm not very savvy computer. I can use my computer to perform tasks and use the software, but I m not very got when it comes to computer and tinkering under the hood, somehow.

  I was using the laptop yesterday evening to watch a You Tube playlist and was downloading a PDF 29MB file in the background. I have done this kind of thing before and never encountered any problems.

  When the download finished (I use Google Chrome) I clicked the button at the bottom left of the screen to open the download. You Tube then frozen.

  I could see the little green circle spinning around like loading upward download, but nothing was happening. Then Google Chrome no longer according to the bar at the top of the window.

  I tried CTRL + ALT + DEL, but the workload Manager wouldn t. The only thing I could do was turn off the laptop and running again, as it had frozen him completely. When I turned on it again, I had the Windows error recovery menu as shown in the following image.

  http://www.TechJaws.com/wp-content/uploads/2010/03/Win7-error-recovery.PNG

  The problem is that none of these options does nothing. If you choose the recommended option (for example Startup Repair) it comes up with the gray bar saying Windows loads the files and then will just a black screen. By selecting Start Windows normally gets you to the swirling colorful circles that make up the logo Windows and he said: start Windows but still once, it does nothing but just stick to that.

  A friend told me that a BIOS reset * may help. However, I don't know how to get the BIOS on the laptop. He called Insyde H20 installed and I don't see the option to access the BIOS.

  Someone at - it ideas as to what could have wrong and how can I fix? I don't have a recovery disc as my laptop was bought for me by a charity. The warranty has expired now so that I can contact t their support line.

  To be honest I don't think BIOS has nothing to do with it. Start your laptop and press F8 several times to display the advanced startup options. You will find the option to start the operating system in safe mode.
  If please test and let us know what happen when you try to do.

• Satellite Pro 6100 cannot start - message PXE - E61 and PXE - MOF

  My dad just bought me a satellite pro 6100 for United off ebay and when I turn it on the toshiba screen comes up, followed by: PXE - E61 and PXE - MOF. as I am a total blank computer I have not a clue what to do! any ideas...? :)

  Hello Naomi

  Don t worry, it sounds not very badly. I think that you will solve this problem by changing some settings in the BIOS. ;)

  To my knowledge, this message appears when the LAN option has been fixed at the beginning of the boot order. So solve this problem to get into the BIOS (ESC and F1) and then change the order of Boot CD Drive drive HARD etc...
  Please set the LAN at the end.

• Satellite A30 PSA30E cannot start properly - PXE - E61: Media Test Failure

  Hope someone can point me in the right direction.
  I decided to use the recovery cd to format my laptop and do a clean install, because it became very slow.
  It takes an age to start etc.

  I followed the instructions on the leaflet that was packaged with the CD and everything seems to work very well.
  The files seem to be loading but after abuot 7-8 minutes (about 15% in the process) is an error page came with the following.

  "For Realtek RTL8139 (X) /8138/ 810 X PCI.
  PXE - E61: Media Test Failure, check cable
  "PXE - MOF: PXE Rom of output.

  I noticed that the power supply has been very hot and the bottom of the computer was also very hot so perhaps thought that the power supply is maybe defective. I had an another same PSU so tried again with this.

  Same problem again!
  Do you think that the hard drive is faulty? I haven't noticed any problems before, except for the slow response generally.

  I would be grateful for any useful comment.

  Hello

  This message usually if the laptop cannot find a bootable device and finally tires to boot from LAN.
  But if the boot to LAN is not possible then the message PXE - E61: Media Test Failure, check cable would appear on the screen.

  Generally, this will happen if the HARD drive is not accessible (dead or defective) or the laptop cannot boot from the disc.

  I think that you should first check if it would be possible to solve this problem by using a new HARD drive.

  Goodbye & good luck

• Satellite Pro A200 - cannot start with new RAM

  I have two of these laptops, both purchased at the same time.
  I upgraded to 320 GB hard drive and tried to move the RAM to 4 GB as the spec States can be made.

  I used the recommended type of RAM, but the computer does not start with two RAM modules inserted. If I remove one of them, the laptop boots! I thought that I update the BIOS but found the only version available on the download web site is the same as I.

  Does anyone have an idea what could be wrong?

  What RAM you bought? I think that the modules are not compatible or your chipset does not support the 4 GB.
  Check it with CPU - Z!

  You could test the RAM with Memtest86 ([www.memtest86.com]).

  I doubt that a BIOS update will solve the problem. A more recent BIOS does not change the decision-making ability and/or supported RAM.

• Satellite Pro M10: Cannot install SD-C2612 - device IDE hdc unknown

  Hello.

  My CD/DVD-Rom device (toshiba SD-C2612) stopped working - it was still registered as a player, but would not read disks - so I got a replacement and not at all settled.

  I also noticed that in device - under IDE ATA/ATAPI controllers Manager - there is an "unknown device" which is called "hdc" (hard disk controller?) who doesn't have a driver installed and can not find new drivers when I update. I disabled the device and who have stopped the old cd/dvd rom recognized and when I reboot it reinstalls the hdc, but it's still the record as an unknown device.

  Any ideas?

  Thanks in advance

  Hello

  It seems that you have purchased an internal drive is not compatible.
  It should know that the drive as master/slave or c - salt settings are fix and it of not possible to change it as on external drives by switching the jumper.

  That is why it s always a good idea to ask the laptop manufacture support for a good disks before you buy a.
  I found in my user manual for the list of compatible drives for my laptop. Maybe it s the same list in you user manual.
  There you should find the readers supported.

• Satellite Pro M10 - infrared does not work properly

  Hello

  I have a Satellite Pro M10 and my infrared does not work. I downloaded the zip file with the drivers from this site. Then, I uninstalled and reinstalled, but it always happens in the Device Manager under "unknown - SMC IrCC - Fast Port infrared (IR Module: HP). (with an exclamation point). When I look at the properties it says under device status:

  This device does not work properly because Windows cannot load the drivers required for this device. (Code 31)

  Click Troubleshoot to start the troubleshooter for this device.

  However, under Driver Details is said:
  C:\windows\system32\DRIVERS\smcirda.sys

  I extracted the zip file in my home directory of c:\downloads\infrared.
  whatever I do, it does not now. It worked when I bought it, but I have too many things on the system for a new installation. Which brings me to another question. Is it possible to re - install windows without losing all your data, etc.? I did it with other systems (95,98) Windows. But it seems that the Toshiba recovery disc means any wiping.

  Thanks in advance for any help.
  Chris

  Hello

  If your HARD disk contains two partitions and you have saved the data on a second you can reinstall the operating system on the first partition using recovery DVDs.

• Satellite Pro M10 - starting problems

  Hello

  I have a Satellite Pro M10, only 2 years old, but has big problems at the start line.

  The message that appears when you turn on it is:

  'Intel(r) Boot Agent FE v4.1.09
  Copyright (C) 1997-2002, Intel Corporation
  PXE - E61: Media test failure, check cable of
  PXE - MOF: Exit Intel Boot Agent.
  Insert system disk in drive.
  Press any key when ready... »

  Now, I talked to a few people and they all say I need a new drive hard etc., but I don't see how replace you it as it looks like it is built in instead of something that can be drawn.

  Also I don't have a system disk, and the guy who provided it has decided not to return my emails?

  Can anyone help please?

  Chris

  Hi Chris,

  It is possible that this notebook you trying to boot from the CD rather than the hard drive. Check in your BIOS settings to make sure that the boot order is correctly specified as HD first. I would not recopmmend change the hard disk at this stage, since it would mean having to restore your system from a recent backup (if you have a) or re-installing the CD recovery.

  HTH

• Satellite Pro M10 will not start again and comes up with the error message

  My laptop Toshiba Satellite Pro M10 will not start again and comes up with the error message "load error" when I press the power button.
  The arised problem after installation of the 'symantec system works' and try to restart windows XP Professional to make the installed executable program.

  What can I do to get the notbook again reboot?

  Hello

  Seems that there are problems with the files of GoBack.

  Try to boot in safe mode and remove the Norton System works from your laptop ;)
  If this does not help, you will need to recover the laptop with the recovery CD Toshiba delivered!

  Also I recommend to visit the Symantec support site and to check the solutions to the problem with the Norton System Works programs

  Good luck

• Satellite Pro M10 PS630E does not start after upgrading CPU

  I tried to install a new processor for my Toshiba Satellite Pro M10-PS630E.
  He initially has a 1500, I tried to put a 1766.

  I follow the maintenance manual, later the computer change is not star upward.
  When I connet to power it show that the luminous power of orange/amber color and make 5 flashes, then 3 and then restart blinking.

  My question is "is it posible to do a reset of the bios parametrers" or "reset the CMOS?
  Is it possible to get it working again.

  Hello

  The flashing light means that it has detected a hardware problem on the motherboard!
  Perhaps you have used a wrong CPU and is not compatible.

  Perhaps the BIOS does not support this processor and therefore this flashing error code appears.

  What say you can't update the BIOS! First of all, that's not possible since only focused on the victory of BIOS is available for download. You must run the Windows operating system to update the BIOS.
  Secondly the update of the BIOS won't help you with this problem!

  You must use a CPU that is fully compatible!

  Welcome them

• Re: Satellite Pro M10 - strange Boot problem

  Hello.

  My Satellite Pro M10 has developed a strange problem. It will power with its installed hard drive.

  The yellow light beside of the plug symbol starts flashing. When there is no hard drive not connected, or another hard drive from another trendy laptop it starts fine?

  Please help, thanks in advance,

  Destro

  I don't know how to help you. HARD drive changes and everything will be ok.

  Is - this original hard drive that you got with your laptop?

• Satellite Pro M10 displays the characters currupt at startup

  I have a Toshiba Satellite Pro M10 that collapsed. When the system boots, the Toshiba logo seems to have a few points here and there. When displaying messages on the screen during startup, the characters seem corropted. For example, the message "Insert system disk", I and T of the insertion of the word seems to be half upper ASCII characters. The system S is the "less than or equal to sign." and the k of the scratch disk is {.} I already did the following:

  -tried to start with one of my two memory card and I tried the two memory cards.
  -swapped my memory card.
  -reloaded windows and Linux

  I have dropped it once but worked OK for a month after I dropped it. I deleted the operating system, but now seems to have problems to load a CD operatig system (CD works OK). Anyone have an idea what is wrong?

  Thank you
  Peter Loo

  Hello

  You suggested that the cell phone dropped twice.
  Well, you can try to connect the external monitor to the laptop to see if it s a screen failure or malfunction of the graphics card.

  You have problems with the installation of the OS? Maybe there's something wrong with the disk and the HARD disk. But maybe only loses connection is responsible for the problems. Check the pins.

  It is possible that the screen and other devices was damage due to falling down.