Satellite Pro A200 - cannot start with new RAM

Similar Questions

• Satellite Pro A200 - black screen with a blinking cursor

  Hello

  I'm new to the forum and have a big problem.
  So, any help is welcome and appreciated.

  My Satellite Pro A200 turns black after the BIOS screen and a black screen with a blinking cursor.
  Also just as the screen goes black a beep can be heard which shows windows boot.

  I can access the toshiba Setup screen but not the installation of security mode.

  Kind regards

  Hello

  Please go into the BIOS settings and check if the HARD drive is listed there.
  The blinking cursor is a typical sign of a malfunction of the HARD drive.
  Eventually the HARD drive is dead and you need to replace it and reinstall the operating system.

  Good luck

• Satellite Pro A200 - cannot install Windows 7 cause lack CD/DVD driver

  Hello, I have a Satellite Pro A200, PSAE4E-046018N5 and I am trying to install Windows 7 but I can't go to step one because it is not found a driver:
  A message box saying: required A driver of currency for the CD/DVD drive is missing. If you have a driver on floppy disk, CD, DVD, or USB flash drive, please insert it now.
  -What to do?

  CD-ROM is a HL - DT - ST DVDRAM GSA - T20N ATA, the actual driver have version 6.0.6002.18005 (date: 2006-06-21)

  Best regards
  /Peter

  Hi Peter,.

  Try you to an upgrade from Vista to Windows 7 at the moment? If Yes, please try a new and clean Windows 7 installation. It work?

  Another question: your CD/DVD drive works properly or it appears with a yellow exclamation point in Device Manager?
  In your case, I would try to remove the drive from Device Manager, then restart the laptop. After that the drive will be recognized automatically.

• Satellite Pro A200 cannot connect to the wireless network

  Hello

  I have a Satellite Pro A200 and Tuesday night I was able to connect to a wireless network. I received an update, rebooted and now it doesn t seem to work.

  I can see the wireless networks available via the Toshiba Radar but cannot connect to my usual wireless network.
  Also, the wireless network icon disappeared from my system tray and if I go to Control Panel/network connections, I can't even view available networks because there is no option to do so.

  Any ideas?
  the FN/F8 will work?
  Help! Please, I beg you!

  Have you tried using System Restore and restore the operating system on time earlier?
  Maybe this will remove the update installed, and you can again use the WLAN.

  Check it out.

• Satellite Pro A200 cannot install the driver of storage on an unattended installation

  Hello

  I created an image of XP RIS for a Toshiba Satellite Pro A200 and have downloaded the correct drivers for this laptop.

  I scoured internet solutions on how to configure the .sif file and where to install this driver on the image that he won't seek the intall the storage driver so that it can not find the Sata HD to install the image.

  Everyone knows that before and if so please could you point me in the right direction I've been struggling with this for a few days now!

  Thank you

  Hello

  You must include the SATA drivers.
  The SATA drivers are part of the Intel Matrix Storage Manager, which can be downloaded from the Intel and Toshiba page page.

  Here's a nice instruction how to do this:

  + How to integrate a SATA AHCI driver into a Windows XP Setup CD.
  http://APS2.toshiba-tro.de/KB0/TSB85017Z0000R01.htm

• Satellite L450D - 13P cannot start with the new HARD drive

  Hello

  IME novice steve and real computers.
  Two years ago I have toshiba purchest mine 2 is the toshiba satellite L450D - 13p runing windows7! And my partners is the toshiba satellite pro 7 also runing windows!

  The problem is that my hard drive is scrap, so I purchest a new 500 gb HDD, instaled it put in the disk I got with him and nothing?
  Hope any 1 here can help me

  Thanks a lot steve!

  In general you can swap the HARD drive or update it with more a (ability), but the installation of recovery should work. It is important to use compatible HARD drive for certain system.
  I did several times in the past. No problem at all.

  After HDD change the value of the BIOS default settings and start recovery installation using created the recovery disc.

  Start your laptop and when you see Toshiba welcome screen pres F12 repeatedly to enter the boot menu.
  When the menu is displayed on the screen, put the recovery DVD in the optical disc drive.
  In the menu choose you CD/DVD and press ENTER.
  Installation of recovery should start.

  Please do so and send feedback.

• Satellite Pro A120 cannot start when the printer is connected

  Hi I have a brand new Toshiba Satellite Pro A120 but I'm having a very strange problem.

  I installed my printer - Epson Stylus Photo R300, but now the laptop will not start if the printer is on. When I turn it on the Toshiba screen comes ok, then the Windows XP screen comes with the black background when the blue bar to cross to load Windows but its all disappear and the laptop just hangs and will not!

  However, if you turn the printer off and turn the laptop it starts up fine!

  Its really the printer which is the cause as its only when I turned it on.

  It's never caused this problem with my old PC using Windows XP too.

  Any help with a resolution would be greatly appreicated.

  Thank you

  Adam.

  How to disconnect the printer during the boot process? ;)

• Portege Z930 cannot start with installed RAM module

  My laptop Toshiba Portege Z930-108 has stopped booting with any module of RAM installed in the support.

  If I remove RAM module, laptop computer starts and works fine, but if I install any module of RAM (4 GB 1600 original or a new 4 1600 CL9 or 1600 8 CL11) the computer cannot start.

  The screen stays black and power led flashing two green and two orange and a few seconds later, 3G indicator also on blue.

  This is the only problem I have with this computer, but it's strange.

  I updated the BIOS to the latest version and the problem is not resolved.

  I tried to reset the hardware (http://aps2.toshiba-tro.de/kb0/TSB3B03J90000R01.htm), also I tried to reset the equipment with power button 30 seconds without battery but button without success.

  Any idea on this problem of strage?

  Kind regards
  Lito.

  I guess you used bad RAM or not fully compatible modules.
  It's the only plausible explanation.

  I recommend you to order the RAM modules recommended by Toshiba that are:

  4 GB DDR3 - 1600 PA5037U-1M4G

  2 GB DDR3 - 1600 PA5037U-1M2G

• Satellite Pro M200 - cannot start Windows

  I have a Satellite Pro M200 PSMC4A, did an update Windows, requsted to restart, then the black screen as follows:
  Windows could not start. A recent hardware or software change might be the cause. Equip the installtion disk and restart. Problem 1: having no disk - lost I think. Lost file is \Boot\BCD.

  Tried different legal remedies without success. Disk Windows XP used to reinstall but now says cannot see all hard drives!
  All of the suggestions.

  Hello

  You can access the advanced boot menu? If so, you should try to start in charge more than the last known good configuration.
  If this is not the only option is to reinstall Windows I think. Therefore, you can take a Microsoft or Toshiba drive. If you don t have the Toshiba disk recovery, contact the service provider authorized in your country.

  I think that the recognized HARD wasn t disc because you need SATA drivers. Did you check that?

• Satellite Pro M10 cannot start properly - AC LED flashing orange

  Hello

  I have a weird problem that I can't solve.

  (1) when my Satellite Pro M10 the plugged AC adapter and the battery, the AC led is green and battery led is orange.
  (2) when I try to turn it on, several times it not light and the dissepear of leds for 1 or 2 seconds and my AC led flashes orange. Sometimes it lights up as it should be.
  _________
  When this problem occurs, it will take a lot of time before it turns normally. I searched the internet for a solution, but I couldn't find one.

  I already removed the battery and try to turn it on, but it does not solve the problem. Or when I remove the AC adapter and try to start it on the battery itself.

  I also removed the two of them and you press the button power on for 60 seconds. After that, it will sometimes start with mains or battery adapter.

  My bios is updated to the latest version. (I've done this when he started only five minutes ago, but the problem is not resolved). I also believe that when the m10 is enabled and when I close it, it crashes also.

  Do anyone know how to solve the poblem? Thanks in advance.

  Hello

  These problems are very rare and shouldn't t happen if hardware or software is ok.
  Power LED blinking orange means there could be a hardware malfunction.
  It is a code flashing microphone and a technician can be read.
  This code must be translated into the hexadecimal digit.

  But for ordinary users it s not able to know what it means. In my opinion a power electronic malfunctions and must be verified by an ASP.

• Satellite Pro C650 - cannot start Windows more

  I have a Toshiba Satellite Pro C650 11Z model under Windows 7 Home Premium. I'm not very savvy computer. I can use my computer to perform tasks and use the software, but I m not very got when it comes to computer and tinkering under the hood, somehow.

  I was using the laptop yesterday evening to watch a You Tube playlist and was downloading a PDF 29MB file in the background. I have done this kind of thing before and never encountered any problems.

  When the download finished (I use Google Chrome) I clicked the button at the bottom left of the screen to open the download. You Tube then frozen.

  I could see the little green circle spinning around like loading upward download, but nothing was happening. Then Google Chrome no longer according to the bar at the top of the window.

  I tried CTRL + ALT + DEL, but the workload Manager wouldn t. The only thing I could do was turn off the laptop and running again, as it had frozen him completely. When I turned on it again, I had the Windows error recovery menu as shown in the following image.

  http://www.TechJaws.com/wp-content/uploads/2010/03/Win7-error-recovery.PNG

  The problem is that none of these options does nothing. If you choose the recommended option (for example Startup Repair) it comes up with the gray bar saying Windows loads the files and then will just a black screen. By selecting Start Windows normally gets you to the swirling colorful circles that make up the logo Windows and he said: start Windows but still once, it does nothing but just stick to that.

  A friend told me that a BIOS reset * may help. However, I don't know how to get the BIOS on the laptop. He called Insyde H20 installed and I don't see the option to access the BIOS.

  Someone at - it ideas as to what could have wrong and how can I fix? I don't have a recovery disc as my laptop was bought for me by a charity. The warranty has expired now so that I can contact t their support line.

  To be honest I don't think BIOS has nothing to do with it. Start your laptop and press F8 several times to display the advanced startup options. You will find the option to start the operating system in safe mode.
  If please test and let us know what happen when you try to do.

• After WXP installation Satellite Pro A200 cannot connect to Wi - Fi

  I installed Windows XP Home edition on my friend's laptop computer because she has lost the drive and now we can not connect to its wi - fi connection.
  The laptop does not recognize it and it is not listed in the menu of the device. I have updated with 2 WOOD and tried the drivers on this site but nothing

  Any help would be great

  Satellite Pro is exactly (A200-xxx)?
  Obviously you has not installed the right driver WLAN if the wireless network adapter is not listed and recognized correctly in Device Manager.

• Satellite Pro M40 sometimes starts with white screen

  Hello!

  I'm pulling out my hair with this problem.

  For no definable reason that according to me, my laptop will start with a blank screen.
  Not all the time, but, seemlingly, whenever it feels like I need extra help stress on my plate.
  For the most part, with perseverance (starting with or without battery, with or without the adapter, with or without pci with or without mouse usb network card and any combination of these elements), it ends by lights correctly, but sometimes Nothing that I won't get it to start and show me a screen.

  My M40 is 4 months old.
  Since it's purchase sent to Toshiba for repair twice for this problem, when I have exhausted myself trying to coax it into life. Whenever he was sent by saying either the problem has been fixed, or that he had no problem found/all systems ok / "it works very well for us, after testing all week."

  This week [edit: it was Wednesday], I sent it to me, and Yes, I checked the trunk upwards and gave a sigh of relief that there is an image on the screen.
  I wrote a letter to this topic a day or two later (that day he first gave me a screen white, but on closing down and restart, it was fine).
  Today, however, not a week later, I have a white screen again.

  I am reluctant to send for repair again, due to the stress involved and the time it takes and the technicians speaking it works for them.

  If anyone can help, or was faced with a similar problem, please respond.

  Oh, and the solution does not lie with the keys FN + F5, because I tried several times... unless there is a way to 'special' to build on them, I'm not in the running for!

  [Edit]: several hours later, as a demonstration of her bored this problem is, my screen is once more working.

  I went on once again, at the time and no joy. Then, after switching OFF, count to ten and the restart, eureka.

  I'll update with news as it happens. If there are all the necessary specific details about "switching on the environment", just let me know.

  Post edited by: jazziefox

  Hello

  Thank you for your update.
  It's a very strange question, and it would be very helpful if you can put yourself more observational.

• Satellite Pro M30: Question on the new RAM

  Hello!
  I'm going to upgrade memory RAM.
  Is this ok, buy 2 x SO - DDR PC2700 0512 MB Kingston [KVR333X64SC25-512] or 2 x SO - DIMM DDR 512 (pc-2700) Transcend?

  Thank you.

  Hello

  Satellite Pro M30 supports these modules;
  PC2700 256 MB (PA3311U - 1 M 25)
  PC2700 512 MB (PA3312U - 1 M 51)
  1024MO PC2700 (PA3313U-1M1G)

  PA3312U - 1 M 51: RAM SODIMM 512 MB DDR 333 MHz/PC2700

  You must use the Toshiba recommended memory modules and you have don t use all modules of no name.

• Satellite Pro 6100 cannot start - message PXE - E61 and PXE - MOF

  My dad just bought me a satellite pro 6100 for United off ebay and when I turn it on the toshiba screen comes up, followed by: PXE - E61 and PXE - MOF. as I am a total blank computer I have not a clue what to do! any ideas...? :)

  Hello Naomi

  Don t worry, it sounds not very badly. I think that you will solve this problem by changing some settings in the BIOS. ;)

  To my knowledge, this message appears when the LAN option has been fixed at the beginning of the boot order. So solve this problem to get into the BIOS (ESC and F1) and then change the order of Boot CD Drive drive HARD etc...
  Please set the LAN at the end.