Scrolling on the touchpad does not. U410 with Windows 8.

Similar Questions

• Tecra M3 - touchpad does not work with Windows 7

  I have a Tecra M3 I've updgraded to Windows 7. The touchpad does not work.
  The Web of Toshiba site has a Windows 7 drivers for this model. I tried install the driver of the touchpad and PVAT from the A11 model but still cannot make it work.

  Can anyone help? The audio is not working either.

  This old Tecra is not supported for Vista, so it can be difficult to find the correct drivers.
  I can see Tecra M4 is supported for 32-bit Vista, so use this with Win7 32-bit Vista driver in the hope that this will work.

  Audio driver? Let Win7 look good pilot. By the way: your Tecra has AnalogDevices AD1981B audio chip inside. Try to find the right driver Googling autour.

• the joystick does not work with windows 8

  Hello

  I have a problem using the joystick; When I used it with windows 7 it works, but when I tried to use it with windows 8, even if it is detected in windows, it does not work with any of my VIs(labview_2012).is there an issue with labview, or there is a solution to solve this.

  Thank you

  

  I wrote this VI in order to study how to integrate a Joystick into my LabVIEW code (I called the "Joystick Sampler" VI).  It has two parts - the lowest fact function, "Query Input Devices", an array of devices, their names and the number of Axes, buttons and POV "hat", in a table called "Joystick Info".  Look at this attention first, in pay to the array Index that seems to match your gamepad, when plug you it into a USB port.

  The upper code can enjoy (one of the) Joystick (s) at the rate of 10 Hz, which allows you to test the buttons, axes, etc..  Note that the primary function of "Initialize the Joystick" takes a parameter (default = 0) which corresponds to the Index of Joystick, you have discovered by looking at the table Info Joystick (see previous paragraph) - If your joystick, for example, seems to be at Index = 4, thread has '4' in the function Initialize Joystick.

  BS

• The printer does not work with windows 7

  Just bought a Samsung R480 today and discovered that my existing printer is not compatible with it. The Setup disk only works with Windows XP and Vista. Samsung R480 running Windows 7 at the moment.  I was also considering changing my desktop computer for Windows 7 as well.

  So my question is, is it possible to request an another HP installation cd that is compatible with Windows 7? Or I have to buy a new printer that is compatible with Windows 7?

  Thank you!

  The link below should show the selection of OS for the drivers of J4680c. just click on what version of Windows 7 you have (32-bit or 64-bit), then download it the driver full of features.

  Pilot J4680C

• Functionality of scrolling on the touchpad does not work... help!

  I have an Inspiron 1525, just the other day that the functionality of the touchpad scroll has stopped working.  I tried to look in the control panel to find an option to turn "scroll" back on, I found nothing.  I am running Windows Vista. Any suggestions on how to turn "scroll" back on?

  Hello

  Try the system restore before you did it again at:

  How to make a Vista system restore
  http://www.Vistax64.com/tutorials/76905-System-Restore-how.html
  -------------------------------------------------------

  If necessary:

  Control Panel - mouse - look for the TouchPad settings - mine is on the settings of the device and your own tab
  may be different (it is NOT the Scrollings tab which is for the mouse). On some, you can activate
  and disable scrolling and/or define the size of the area and the sensitivity of the touchpad.

  Some will have a TouchPad progam/control icon in the Notification area near the clock - low
  right.

  Check with the manufacturer of system support, documentation in line, or forums as there probably
  are shortcut keys that enable and disable the touchpad functions.

  ==========================================

  If necessary: (make sure that you have restarted at least once, if the above did not work)

  Panel of configuration manager devices - mouse and pointing devices - Double click on the touchpad - the driver tab-
  Click on update driver (it comes may not do anything like MS is far behind the drivers of certification), now right CLICK
  on the TouchPad and UNINSTALL.

  Then go to the USB and UNINSTALL ALL controllers except the category itself (all in). RESET

  This will refresh the driver for the TouchPad and battery USB.

  Here is the similar procedure under XP, Vista is the same, except that we need to clear the specific device if present.
  http://support.Microsoft.com/kb/310575

  Then go to the system manufacturer's website and get the latest touchpad drivers.

  Download - SAVE - go to where you put it-click on - RUN AS ADMIN.

  Dell support
  http://support.Dell.com/

  Dell support drivers - product manual & warranty Info (left side) - and much more
  http://support.Dell.com/support/index.aspx?c=us&l=en&s=DHS

  Dell forums
  http://en.community.Dell.com/forums/

  I hope this helps.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• Pavilion G6 2338sl: hardware button to turn off the touchpad does not work on Windows 10

  Hello

  I have a Pavilion G6 mobile 2338sl. When I was on Windows 8.1 the touchpad worked a lot, so I've updated for Windows 10. Windows updated my drivrs to last, provided also by Synaptics (19.0.19.1). HP says the moment is upgrade from Windows to provide the driver for this laptop, as you can see on the driver support page. The touchpad works, the parameters can be set (gestures etc.), the touchpad turns off when another mouse is connected (it's ok).

  The problem is that if I use the touchpad and I want to turn off the button, it does not work and the computer reacts like a click. So I returned to the old driver and button works. But Windows Update continusly updated the driver (I disabled the option in the advanced settings, but it still update) and I come to every time.

  So I tried to reinstall Wndows freshly (not update Windows 8.1) and with the old driver works, but when she updates to 19.0.19.1, the button to turn off the work stoppage.

  I looked on the interent and someone tips to set minimum detection of palm. I tried but it still not working.

  I hope someone can help me

  Concerning

  Hello

  If you find that the old Synaptics driver works Ok, install it and then use the utility on the following link to prevent Windows 10 to automatically update again.

  https://support.Microsoft.com/en-GB/KB/3073930

  Kind regards

  DP - K

• My scanner on the MF4370dn does not work with Windows 8 or 8.1.

  I have a Canon MF4370dn which the scanner part has not worked since I was a computer with 8 windows and will not work at all since I downloaded windows 8.1 right.

  I rebooted tools scanner, tried the Presto! PageManager supplied with the oomputer. I downloaded the latest drivers for the scanner on the site.

  He has worked with Windows 7 fine, but this computer is no longer functional and I often use my scanner.

  Any ideas?

  Solved my problem by redownloading and installing (x 64) Windows 8 pilots and Toolbox software. Thanks anyway.

• Scrolling on the touchpad does not work after update. All advice?

  Hello I have a problem with my touchpad. After upgrade yesterday I can't scroll with it and I can not change the resolution. All advice?

  I have win8

  OK found:

  SVP1321L1EBI

• Did not know that the program does not work with Windows Vista Edition Home Premium

  I am currently using Windows Vista Home premium with a 64-bit operating system and I'm unable to download my product purchase Adobe photoshop elements 14. Any help would be great.

  If you are unable to upgrade your operating system or your computer, and then return the software for a refund.

  Return, cancel or change an Adobe order

• Satellite X 200-219 - the touchpad does not work as it should

  Hi all

  I recently bought a 2nd hand Toshiba Satellite x 200-219. Had some problems with it that I have overcome now, except one... The touchpad does not work as it should. I think that the cable has been damaged at some point.

  So I'm wondering if I should use the same ribbon cable to connect the keyboard to the motherboard or can I get one of a different model of PC Toshiba laptop?

  I tried searching on the net for advice but have resulted in nothing so thought I would try the forums.

  Any help you can give will be greatly appreciated.

  Thanks in advance,

  Lee

  I think you can use the items to the satellite X 205 series since this seems to be the same series as X 200:
  Found some related parts the touchpad:
  Satellite X 205 / X 200 touchpad Board with cable: reference number: K000047950
  Satellite part number for the TOUCH PAD FFC X 205 / X 200: K000047980

  But why you n t come into contact with a Toshiba authorized service provider in your country and order the part necessary and compatible?

• Satellite C850D-11 q - keyboard and the Touchpad does not

  The laptop is a little more than a year and worked ok until recently.

  Symptoms were the keyboard and the touchpad does not not on page 8 of windows logon. Pressing power to put the laptop into sleep and pressing still often got their work.

  He progressed to the keyboard and the touchpad works do not randomly points while the use of the laptop.

  Finally cleared the HARD drive and restored windows 8 alone, the laptop still BSOD quite frequently - refuses to install the updates required for 8.1 and the keyboard and mouse often do not work even in BIOS Setup page. I reinstalled the RAM and HARD drive.

  Short of ideas, the keyboard and the touchpad work and so I guess that their connections are correct - but often they just stop.

  Any ideas appreciated?

  Thank you

  Hello

  > Finally cleared the HARD drive and restored windows 8 only
  I hope that you created before Toshiba recovery disks you have formatted the system.
  Did you?

  The recovery disks will allow you to reset the laptop to factory settings; on the same State as at the first day of the purchase.

  > First symptoms were the keyboard and the touchpad does not not on page 8 of windows logon. Pressing power to put the laptop into sleep and pressing still often got their work.
  Well, usually the keyboard problems are not problems system or software as the keyboard driver is part of the system and an additional installation of some drivers is not really essential and necessary.
  That is why in most of the cases the keyboard problems could be the causes of physical problems.

  However, after using the recovery disc and the parameters of the laptop back to factory State, both parties (keyboard and touchpad) should work perfectly.

  > the BSOD laptop still quite frequently - refuses to install the updates required for 8.1
  BSOD doesn't look very good. As mentioned above; parameters of the laptop back to factory settings should solve all the problems in the system. In the case where the BSOD appears even if the power has been turned back to factory State, a hardware problem could be the reason for this.

  I had also some problems with the update 8.1 Win. The system to win 8 could not find the Win 8.1.
  But the reason for this was simply. I had to install all updates to Win 8 and had to update the State system before trying to update to the next level following 8.1 Win

  So, what can I say: I will try to put the laptop initial configuration using the recovery disk.
  Then I would try to get automatic updates (a few reboots were essential too). After that, I would check the functionality of the keyboard and the touchpad. In the case where them parts would not work, I would contact the service to check if the two pieces.

• Windows 8 - horizontal scroll on the mouse does not

  Hello, everyone,

  I have a system running 64-bit Windows 8. My Gigabyte M6980 mouse has a wheel tilt with a capacity to reach not only up and down but also left and right. However, the inclination of the wheel does not record in my Win8 machine.

  I plugged the mouse on a Vista laptop where initially the system has not yet recognized the mouse at all (the cursor is not mobile). After going to the Manager of devices and update the driver for the "unknown device" which was M6980, it became a "HID-compatible mouse. I could then move the cursor AND use the horizontal scrolling. On a Windows 7 computer, the mouse was recognized immediately and I could use horizontal scrolling very well.

  I tried to copy mouclass.sys of my laptop Vista and mouhid.sys to C:/Windows/System32/drivers on my machine Windows 8, but then the mouse could not be recognized at all the original files should be restored. The same thing happened when I copied the same files from a Windows 7 machine.

  Gigabyte support response is that the mouse does not officially support Windows 8 and all the features are not guaranteed. There are no drivers available for the device and the only software that comes with it is motor Ghost of Gigabyte for remapping keys. But given that horizontal scrolling works in Windows 7 without any additional software, I suspect driver Windows 8 HID is involved, although I could well be wrong. I couldn't Google solutions. Any help would be appreciated.

  See you soon,.
  Jesse

  Hi ShiuabKhan,

  Thanks for a quick reply. Windows 8 is now picking up the thin horizontal scrolling messages. I tried to randomly check the software option Gigabyte 'disable horizontal scrolling' and apply changes and then uncheck the new, and, curiously, it started working. However, I install the latest version of the software from Gigabyte (which just happened to be released February 1) in compatibility mode to be on the safe side.

  Although the system is now picking up messages from horizontal scrolling of the mouse, my Battlefield 3 game won't recognize them, but is not a Windows problem, so I'll find an answer elsewhere.

  Thank you much for the help!

  See you soon,.
  Jesse

• FN + F3 disable the Touchpad does not work. Dell XPS L702X

  Hello, I am new to this forum.

  The function FN + F3 that disable the Touchpad does not work, my laptop Dell XPS 17 (L702X)

  I googled my problem and the only thing I found was this: http://en.community.dell.com/support-forums/laptop/f/3518/t/19454265.aspx

  I think that my problems with the touchpad started when I plugged a mouse into the USB port. It didn't work (it worked well before), and in material-sound-mouse control panel, the system asked me to uninstall a driver or other. I do not remember, but later the mouse worked.

  After this weird thing with the mouse, I noticed that the touchpad was malfunctioning. While I write, the cursor moves without touching the touchpad, it is annoying because it makes me write bad because he is moving in the middle of writing, as I write so it's a mess.

  The second oddity, the Fn + F3 does not disable the touchpad, the orange light come on (the led on the top of the touchpad), but the cursor can be moved in any case, with or without a connected mouse.

  I checked for driver updates, perform an audit of the system, checked for viruses, spywares and I don't know what I could do. I don't know if the problem with the mouse had nothing to do with the function Fn + F3 problem.

  I have not formatted or re installed windows 7, never.

  In Device Manager I have this:

  -mouse and other pointing devices:-Compatible PS/2 mouse

  Help, please. Thank you.

  DOH! Problem between Chair and keyboard...

  C:\dell\drivers\R289237

  Run the executable file of Synaptics.

  Download of extracts only the program on your disk. You must manually install the driver for the Synaptics touchpad with its own executable.

  FN + F3 now disables =)

• lovely better does not work with windows vista home Premium what another program removes LSO and HOW to prevent the trackers?

  Question
  better privacy does not work with windows vista home Premium that another program removes LSO and HOW to prevent the trackers? Edit
  Details

  In current versions of Flash you can also do this via the control panel.

  • Control Panel > Flash Player, click on remove and erase data

• HP 250 g3: hp 250 g3 does not start with windows 8 ir says the GPT partition style

  HP 250 g3 does not start with windows 8, it is said GPT partition style and custom boot that I have fomarted the hard drive... Please help

  Thnx man always the same thing, but I deleted all partitions and then I was able to start...