SD card prob

Similar Questions

• Sound card prob

  Hello guys

  it, s been a sense I used my laptop since the death of my audio card due to problems of unknow

  somehow I was wounering if none know what kind a sound will be support/compitable with my m system so I can replace or if hp sell

  Please I need help I'm ahead enough with the pc but I can't solv this problem and it came to my attention that I need to replace

  so if you please

  entire map its compitable

  What type of pci express only my knees has {if all avaiable}

  What kind of express card {I know that he is one, but I don't know what kind}

  help will be very appreciated all ago thanks in advance

  my pc Info

  HP Pavilion dv6815nr

  Windows Vista Home premium 32-bit

  Processor AMD Turion (TM) 64 X 2 Mobile Technology TL-60 2000 Mhz, 2 Lossnay, 2 logical processors

  2gig ram

  In the notebooks, the sound chip is build-in with the motherboard, there is no slot pci for sound.

  Are you sure that the sound chip broke? Not a driver problem?

  If so, the only option to buy a USB sound card and use external speakers.

• Power edge T410 - ERROR 1 [MS]

  Hi all

  I have a problem with a computer model "Power edge T410.

  We noticed an intense and continuous cooling fan activity.

  The small appears:

  <>

  System Board ambient temp: temperature of the system, warning event card probe. >>

  Does that mean exactly? What we can do to fix it?

  Thanks in advance

  Concerning

  Buongiorno,

  MI manda copia dei registrati newspapers?

  Dal server administrator: clicchi knew System sulla sinistra, poi su newspapers nella cornice Central, quindi su export logs

  MI servirebbe anche di sapere quali siano the temperature register:

  System-->--> temperatures main system chassis

  Speaking saluti

  Manual

• Yet Cs4 breaks down I'm starting a new project and gives me an error message [..-.. \sre\AME Prober.cpp - 258 preset] I chose nvidia 880 M graphics card and I tried to go to the old dr

  I asked a question here before and got a response, so I'm back. Yet Cs4 breaks down I'm starting a new project and gives me an error message [..-.. \sre\AME Prober.cpp - 258 preset] I chose nvidia 880 M graphics card and I tried to go to the older driver

  I couldn't on the forum last night! And today too busy...

  I think that a reinstallation is the only solution for the preset errors prober TEA that has been reported. Activation etc problems can be problems, if you have a subscription to the CC, try all the options to sign out/in on the cloud first Office.

• Prob with the network card driver after installing vmware tools

  Hello

  I have 3 ESX 3.5 Update 3 and a VC 2.5 update 4.  I've updated an ESX for release 3.5.0 153875. I've also updated the customer vlmware on each virtual machine on the esx server. When I restart the machine virtual (Linux Redhat 5.2 or Windows 2 K) or Windows2003, I cannot ping the vm for +-5 minutes from my pc, but it works if I do a ping to a virtual machine in the same vswitch. If I disable/enable the network device, I can ping directly.

  If I remove the vmware-tools I can ping directly after a reboot...

  Thank you for your help

  Very strange.  Try to use a different type of NETWORK adapter, enhanced vmxnet and see if you see the same behavior.  There may be a bug with the latest version, and if the problem persists, you can open a SR with vmware.

  -KjB

  VMware vExpert

• HP P6 - 2107c: sound card keep settings for recording level.

  Sound level for the line or microphone will remain unresolved.  It keeps jumping back to cut and zero.  Settings for probe or reading will hold.  I tried to uninstall the driver and reinstall it but this is the same condition applies.  Volume for the microphone or line will run for a few seconds or a few minutes and then comes back to a State of mute.

  Any ideas on how to resolve this short of installing its own card.  I use the IDT located on the motherboard.

  Thank you for the additional information.

  Given that you have uninstalled and reinstalled the driver, it may be necessary to do a full System Recovery using the recovery discs that you made when you purchased the computer.  Once a computer has been used for several years, it is not uncommon that the glitches to occur.  I do a system restore at least once a year.  I love the way that the computer runs after ended.  If you decide to do, you need to back up your personal data before recovery.

  Please click on the button + Thumbs up if I helped you and click on accept as Solution If your problem is resolved.

• Problem of graphics card on Portege series

  Hello!

  I had a real problem.
  I played DOOM95 on the book and after a while the book crashed, winXP crashed.
  Since that time, I have strange problems with the VGA card.
  If I install the drivers from Trident XP4 I get grafik problems in Solution Explorer and I can't starty any programm based 3d.
  By exempel 3dmark or Guild Wars.

  If I use WinXP driver standart. I have no probs but also no 3D support.
  I have managed to set up the book without Cd-rom with a RIS with a WinXP SP2 server.
  Same problem again.
  I hope someone has a sultion for this problem

  Sorry for the English.

  Greatings from Austria

  Hello

  Have you installed the latest version of DirectX software? As I remember the version 9.0 c is the most recent.

  After installing DirectX, start this tool by using the command: dxdiag
  Here, you must enable features such as Direct 3D and DirectDraw acceleration.

  I hope that this little instruction will help you

  Good bye

• H8 - 1280t - QC461AV #ABA: desktop HP - computer does not start after the installation (Windows 10) video card

  So, I just bought a new video card an XFX R9-390 and a new HX1200i POWER supply corsair (overkill ik ) that I put on a card mother IPIWB-PB for my 3 years old HP PC, and the new stupid video card is not working. the PC just does not start, I see is a black screen. My monitor is an HP 2311gt and I can't use my computer with the old video card no probs, BUT whenever I have to install the new card does not detect my monitor just and I only see a blank screen. I HAVE NO IDEA HOW I'M DOING. Help, please

  PS. I have RMA the new power supply and the video card and they got to check and send back to me, so I know that the two pieces of equipment are working very well AND of course I am currently using my PC with the old video card

  Wiraqocha, here is the link to start safe for HPs with Win 10 and instructions to enter the BIOS. It may be useful:

  HP PC - secure boot (Windows 10)

• Qosmio G30 - nVidia graphics card failure

  Hello

  as the title says my graphics card went kaput on Qosmio G30, who is 14 months old.

  I read in some places that could be the problem with the generation of nvidia graphics cards.
  Does anyone have any info on this subject because I have just quoted entre.6 and 1.8 k for what fixed it.
  This graphics card is separate from the motherboard or this prob will result in a new motherboard. If anyone has any info I would be very grateful, thank you, thomas

  PS for some reason that I could not connect with my username (yetchh) original so had to create a new account, have no idea why?

  Post edited by: yetchhh

  Hi Thomas

  That s a pity :(
  Especially the GPU (graphics chip) is attached to the motherboard. He welded s and replacement is not easy.

  There are several Lepidoptera, I called the ASP in my country because I needed some info on replacing the CPU on my old laptop and the guy said that the replacement of the CPU or GPU is not easy and is not possible.

  Well, what to say I think you should contact the authorized service provider in your country for replacement of equipment.

  But I wonder why you come in on costs?
  The laptop is about 14 months. If you have registered your laptop on the Toshiba page, you should get a 2 year warranty which should focus on the laptop.

  So all pieces of equipment should be replaced for free.

• Can I use a probe with my NI4461 to measure the 100vpp(permanent)?

  Hello

  I use a NI4461 card with 2 inputs and 2 outputs. I have a signal generator with a signal of 125 Hz 100vpp(permanent) I want to characterize using labview (FFT, amplitude, etc.).

  The limits of entry on the NI4461 being +/-42 .4V, I was hoping to use a X 10 probe, which is similar to a scope.

  However I find this works do not correctly in the mitigation of the probe doesn't seem to be a constant 10 x. Although my reach (with a second probe) reads 100vpp(permanent), my NI4461 detect 82Vpp.

  Am I missing something? Are there alternatives to read > 42.4 v reports on the 4461 with a probe?

  I checked and exchanged probes and they both work find on the scope, but not on the 4461. Is there a special probe that has a match of good impedance for the 4461 you can recommend?

  Thank you

  Thanks for the suggestion.

  I actually build an out two very large resistance voltage divider which seems to work fine.

  The circuit is simple, two resistors in series connected to the ground at the same time on my main unit. By attaching the son of sense of tension on a single resistance I can divide the voltage in two (two resistors have the same index). I calibrated the system and it seems to work.

  Thank you for your suggestions.

• Probe FBUS node

  Is it possible to continuously send sensor nodes to the field device and monitor the response of the probe to check if a package is missed?

  I want to program the NOR-FBUS configurator to send PNs programmatically.

  1 NOR-FBUS interface device always use master link and LAS.

  2. battery (firmware) of the interface card OR-FBUS (PCI/PCMCIA-FBUS/USB-8486) is responsible for the shipment of the promissory notes. The stack is running on the device interface. It can not be controlled external. In fact, there is no need to send by programming interface card PNs. NOR-FBUS will send PNs automatically and permanently as long as Manager of Communications is running. You don't need to run the Configurator.

  3 communications Manager or the Configurator cannot monitor the FF data at the level of the Protocol packets. Configurator is a tool to configure without feature followed by data packets. To do this, you must use the OR-FBUS Monitor software. Monitor is a capture tool data package to the level of the Protocol and analysis.

• Equipped with mobile broadband with Lenovo B560 / SIM card / no reaction if pushed SIM card

  Dear Forum

  I have byued "nine" one lenovo B560 - quiet price specifications.

  But now I'm trying to connect to internet with my SIM mobile broadband WebClient and do not find a way to do it!

  The laptop is equipped with a SIM-Card-Slot-In card and throug this Slot I can see some golden conectors.

  But if I turn on wireless with [Fn] + [F5] I can't see the WLAN on/off switch card.

  Even the installation of 5 ReadyComm has not resolved my probs.

  My mobile is Win7 home premium with the typical standard configuration, no change.

  Is there something that I did not?

  I appreciate any help, thanks in advance!

  Greetings - sand

  Hello mate,

  It's not because you have a card reader sim you have a modem installed inside.

  If your laptop is wwan ready, it comes with the sim card reader and installed antenna, and that's all.

  If you don't see the wwan modem in the Fn + F5 menu it is probably because you do not have a modem.

  Take a look here to see if you have a wwan modem or not: http://consumersupport.lenovo.com/us/en/configuration/configuration.html

• IMAQ Grab Acquire.vi error when you use an external trigger on a card NI PCIe-1433 (sync problem?)

  According to my recent post on getting up and running with the NI PCIe-1433 camera link card, I ran into a bit of a snag.

  When you use the internal trigger on the camera, everything works 100%. I can view all the data from the camera in MAX as well as in the labview project. However, whenever I have set the mode switch is where things start to fall apart.

  What I have confirmed:

  -Camera is switching between inside and outside triggering.

  -NI PCIe-1433 camera link card is set up properly. While in external mode, I can trigger the camera by using a function generator and check the wire to the MAX. Everything works fine.

  When the unit is in external mode, the function Acquire.vi enter IMAQ - my mistake VI. The error is:

  Code :-1074397150

  The possible reasons for a timeout.

  Now, I have it set up so that a mistake here will not end the LabVIEW file. Sometimes, data of interest makes however (about every 10 seconds-ish). So what seems to be the case, it's that this external trigger signal is not in the lineup when the clamp is attempted. Is it possible to synchronize these? May reference the trigger signal external sort in my LabVIEW project so that the clamp is performed only when that trigger impulses?

  So I solved my problem. He was in time. The external trigger that I used for the device was simply too slow. I was initially using a trigger from 2 Hz to be able to view the values changing on LabVIEW probes. But it was enough to get enough data to move above the camera cable to assemble a picture and kept it in time. Travel up to 9 kHz solved the problem. No adjustment to the camera settings or LabVIEW code was necessary.

• Exposure / white - black voltage settings on the PCI-1410 acquisition card

  Hello

  I use a PCI-1410 acquisition card and have written acquisition software in Visual Basic .NET.

  In measurment studio there is a button that automatically sets the tensions black and white, based on the tensions of entry on the channel.

  I want this impliment into my VB.NET code.  I am aware of the 'CWIMAQ. BlackReferenceVolt "and"CWIMAQ. " WhiteReferenceVolt' properietes, BUT is there something that will automatically adjust the tensions?  I ask because I don't have background no function that will probe to find what is the maximum and minimum voltage that is nessasary to dynamically set the tensions.

  Thank you

  Jonathan

  Through the research forum.  If the solution below to create the IMAQVision control.  IM assuming that the reason why it wasn't available is because I do not have the license of installed vision

  Dim IMAQVision As New NationalInstruments.CWIMAQControls.AxCWIMAQVision
  IMAQVision.CreateControl)

• HP Pavilion ZD8000 wireless card replacement

  Hi all, there

  I have a bad wireless card and bought a new one using the HP number #392591-001. It is said it is expected to work in my computer, but I install and said material is not configured right and is not working.

  Here can someone help me find a driver that works or I'm SOL on that. I looked everywhere I know how to find a driver and on the HP website, there is no driver for it.

  Thank you very much.

  OH and my computer will start but will not just set up the wireless card. I think the driver for it is missing. I install the original map and it shows in my devices list just inoperable. I can connect via the Ethernet that no prob and my bluetooth work ok.

  Ciao

  Hey once again Paul,

  OK, so here's the deal. I finally got a response from the boys that I bought and it's the pilot, they sent me. It may just be the same thing on you sent me that I don't know.

  http://www.jhetech.com/eBay/Download/Driver%20For%20BCM94318%20Laptop%20Wireless.exe

  What I did then was to use the manual config when hardware Setup detects new hardware, I pointed directly in the driver instead of searching for him and low and here is it started working. Yay for that.

  I have honestly no idea of what happened, but worked so I guess it's good for me. Thanks a lot for your help and I don't know the driver you sent me would have worked if I'd done it before. I really appreciate the help very much. I also don't know why it didn't find the driver from the start since is is a replacement of hp.

  OH, well you are very useful and hope you have a great day and happy Christmas to you...

  Gene