Search for service console
Hello
I recently installed ESX v3.5 on a server that had 4 network cards, during the installation, I just plugged the LAN cable on a random NETWORK map and the selected installation than NIC for the Service Console which was NIC3.
After installation I discovered in the ESX he had used this NETWORK card and ip 192.168.1.19 for example management console. after boot ESX, it displays the screen saying that you connect to http:
192.168.1.19 for the web client.
And in the ESX I want to do, is change the Console NIC of Service ESX to another nic for example. use the vmnic0 and IP 192.168.1.20 rather than the vmnic3 and IP 192.168.1.19 his currently uses.
So I used the "esxcfg" command to remove the vswif0 and then create a new swtich and qualify the service console IP 192.168.1.20 only there and then I run the esxcfg-vswif - l and esxcfg-vswitch - l to check and it seems to look ok.
But then in the ESX when I press on the Atl + F1/F11 to toggle the screen ESX, it still seems to show the "connect to http:
192.168.1.19 for web client"rather that I have configured the new IP 192.168.1.20 is possible to change this screen to display the correct information as well or have I left out something.
I have successfully downloaded the vi client and can connect by using the IP 192.168.1.20 but the ESX still shows the old IP ' to connect to http:
192.168.1.19 for web client"so I'm not if I missed something.
Also when the Service Console switch configuration is really possible to use a NETWORK adapter rather than the vmnic0, because apparently there is no parameters in the command line "esxcfg?
esxcfg-vswif - a COnsole vswif0 Service\-i x.x.x.x - x.x.x.x where x.x.x.x b n (I can't remmeber if it's the correct syntax).
Thank you very much
If it goes back a.19, so your hostname / IP has not been updated in all the places that I mentioned earlier. Make sure that these files that I referenced contain the correct host name or IP address.
-KjB
VMware vExpert
Tags: VMware
Similar Questions
-
What is the cause of the message "Waiting for Service ' Console CVD activity
I have two related questions.
basis, I just started centralizing 200 computers ish, all except 2 appears fine, 2 questions, one below and another with VSS errors. This message is just for the question "in waiting for the Service.
- What is the cause of the message "Waiting for Service ' Console CVD activity and is there anywhere that documents these meanings of status.
- No idea where I should start troubleshooting the message "Waiting for Service ' I get to the computer below.
I have a computer with this status which comes to have installed the client and will not be to centralize. Other computers seem to work properly (centralized).
The computer is to ping requests, but appears as disconnected in the console.
I deleted the CVD and restarted the centralization CVD using a different policy on a different volume without change.
Journal of the history of CVD below
Description of the Type of weather
31/01/2014-08:52:32 AUDIT_EVENT assign device, device: PC30866 (1995), cardiovascular disease: 11614, political CVD: don't Default - every 4hrs - no drive D (1.1)
02/05/2014-13:53:58 politics AUDIT_EVENT assign CVD, CVD: PC30866 (11614), CVD policy: Migration Post-quotidien (1.0)
31/01/2014 General Office EVENT 20:44:46 service error
31/01/2014 General Office service EVENT 17:39:04 error
31/01/2014 14:44:34 EVENT has not finished downloading, internal error, exception attached
31/01/2014 General error from the EVENT 13:05:15 service office
31/01/2014-12:30:37 TRANSACTION_START PC30866 - centralize endpoint
the transaction log has an inscription mentioning a failure (not sure if it is the server or PC related) disc.
Diseases cardiovascular diseases cardiovascular name Type State layer size (MB) data transferred (MB) branch reflector savings start time end time transfer (MB)
Of the endpoint PC30866 centralize 11614 reading disc failed 169648 1531 0 31/01/2014 12:30:37 05 d 04:16:52
The next event is in the application event log and the Mirage event log for the failed computer. (there were not all other errors in the paper since the deployment of mirage customer and there is no errors in the system event log)
Event type: error
Event source: VMware Horizon Mirage customer
Event category: no
Event ID: 0
Date: 31/01/2014
Time: 20:44:46
User: n/a
Computer: PC30866
Description:
Error general service office
Unexpected exception taken (sender Name:Wanova.Desktop.Service.exe
There is no policy context.
, the object exception System.OutOfMemoryException: Exception of type 'System.OutOfMemoryException' was thrown.
System.Collections.Generic.List to ' 1.set_Capacity (Int32 value)
System.Collections.Generic.List to ' 1.EnsureCapacity (Int32 min)
to System.Collections.Generic.List' 1. Add (T item)
at Wanova.Net.DataTransfer.TransferStreams.SignatureResponseStream.ProcessChunk (ChunkInfo chunkInfo)
at Wanova.Net.DataTransfer.TransferStreams.ChunkInfoDecodingStream.BeginWrite (Byte [] buffer, TransferStreamWriteCallback onWriteComplete)
at Wanova.Net.DataTransfer.DataHandler.ExecuteDataStreamTask (DataHandlerExecutionTask task, MarkCompletionCallback markCompletionCallback)
at Wanova.Net.DataTransfer.DataHandler.ExecuteTask (IExecutionTask task, MarkCompletionCallback markCompletionCallback)
Wanova.Net.DataTransfer.ExecutionController.QueueListener (Group IExecutionTask)
to Wanova.Common.ThreadUtils.ParamaterizedWorkItem'1.Run (object fakeParam)
at System.Threading.QueueUserWorkItemCallback.WaitCallback_Context (Object state)
at System.Threading.ExecutionContext.Run (ExecutionContext executionContext, ContextCallback callback, Object state, Boolean ignoreSyncCtx)
at System.Threading.QueueUserWorkItemCallback.System.Threading.IThreadPoolWorkItem.ExecuteWorkItem)
at System.Threading.ThreadPoolWorkQueue.Dispatch)
at System.Threading._ThreadPoolWaitCallback.PerformWaitCallback (), ends at True)For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp.
It turns out that this computer seems to have hard drive errors, so not a matter of mirage.
-
another name for service console
What is another name for service console?
can someone let me know the right answer...
Thanks in advance
Rajesh reddy
COS? (Console operating system)
It is based of RHEL
-
Hi guys.
Ive been through the strengthening of the security/best practice document and working my way through it.
I understand that its best practices to isolate the service console using a vlan separate but the problem I have with this is things like NTP and DNS does not work as the console will be completely isolated. I have only one Layer2 switch and im wondering what is the best way for acheving this is. Perhaps something like an Hytrust appliance?
Any suggestions, tales of wisdom tor welcome
Thank you
I have to disagree with this statement since Andre, that we have found that when you run a scanner security on the management network (port), and especially against the VMotion network (port), you can stop the services, disable VMotion and so, by default, disabling of DRS.
I used HyTrust and found valuable by adding an extra layer of security.
FYI HyTrust works to implement authentication 2 factor for ESX and vCenter as part of the management functions of the access of the HyTrust Appliance for their next version 1.1. This is for the connections of management vCenter both direct-to-host using Virtual Infrastructure Client or ssh. They are currently seeking to implement for RSA SecureID, smart card, RADIUS and kerberos.
b
-
Determine good network card PCI bus for Service Console?
Are the bus PCI in hexadecimal or decimal?
I ask because I put the Service Console on the bad NIC (0b.00.00) and I want to know which is the NIC low to move it to.
I have the following:
Card internal Broadcom: 03.00.00 and 05.00.00 - I want these to become vmic0 and vmnic1
Map external Intel: 0b.00.00 and 0b.00.0 - I want these to become vmic3 and vmnic4
Am I right that 03.00.00 is the bus PCI NIC plus small number?
Once I know that, I'll add this 03.00.00 vmnic to the current SC vSwitch reassign SC him then remove the other vmNIC to it.
In addition, how is it possible to re - assign vmnic numbers to different network adapters?
Say vmnic0 is on the NIC 0b.00.00 and I really want to vmnic0 on 03.00.00, how do I do? -command and syntax?
Thank you, Tom
Yes, 03:00 is the smallest address PCI - 05:00's next, b 0:00: #'s next - his numbered in hexadecimal - you can reinstall ESX and select the correct network adapter or you can check out here how to renumber - http://vmware-land.com/Vmware_Tips.html#Net4
If you find this or any other answer useful please consider awarding points marking the answer correct or useful
-
I need help
If you see no Service or search on your device, or cannot connect to a cellular network or cellular data, follow these steps:
- Restart your iPhone or iPad.
- Looking for a carrier settings update.
- Remove the SIM card and put it again. If the SIM card is damaged, or does not fit in the drawer of the SIM card, contact your carrier.
- Reset your network settings. Tap Settings > general > reset > reset network settings. This also resets the Wi - Fi networks and passwords, cell parameters and VPN and APN settings you used before.
- If you have another device, see if you can connect your business with her network to this place.
- Contact your operator for:
- Make sure your account is active and in good and due form.
- Make sure that there are no failures in your area.
- Verify that your device is not blocked to receive cellular services and is set up with the right data plan.
- Update your iPhone or iPad to the latest version of iOS.
If you still cannot connect to a cellular network and have confirmed with your carrier is not a problem with your account, or your network, try to restore your device.
If you cannot connect to a cellular network or cellular data - Apple Support
-
Service Console network requirements
Hello
I searched the internet, forums and documents best practices vSphere but couldn't find which are the characteristics of network for the Service Console speed. My management network will be a complete isolated physical switch. I won't use it vMotione etc so it will only be used for H.A. and basic (pulsation of hypervisors, vCenter server connection) operations.
For this, a network of 100 Mb/s should be fine. But if I want to copy a virtual machine offline data to another store, it will pass through the management network? If Yes, then I should get a 1 GB switch.
Thank you!
It is advisable to have gigabit ethernet adapter for service console
copy of the data of the esx datastore Management Office and between the data store will be done by the network of mgmt
concerning
Maniac
-
iPhone 4 continues the search for carrier
Recently, I set my iPhone 4. And the iPhone keeps searching for service or signal or what they called it. I tried just like update my carrier setting, reset the network settings, turn on and outside airplane mode and even restore the phone. The most funny thing is always successfully can I activate my phone without going through signals. It certainly isn't because of the sim card because it works for my 5s. Any help?
The 4 and the 5 s using different size SIM cards physically. You cannot use the nano-SIM of a 5 by 4, which uses a micro-SIM card.
Also, what did you recently to "fix" your iPhone 4?
-
How to access the ESX service console
Hi all.
I'm a TV engineer trying to solve a problem of network with our equipment. I'm not a network engineer.
I'm trying to follow the VMWareKB: "Troubleshooting connection problems network using the Protocol ARP (Address Resolution)" I'm just trying to check the ARP table exists on our ESX Server and has some entries.
KB said running 'arp - a' for a list of the ARP table.
To do this, I need to open a service console. I have now read articles 3 or 4 on the use of the Service Console but I am still unable to open it to run the command. I do not understand what I am doing wrong, I am incredibly stupid or miss me something completely.
An article said, press 'Alt F1"exactly where I am doing this? A virtual machine is connected to the ESX? An article said "to VIM summary screen' I tried logging on the virtual machine and point a web browser on the server, I get a screen of welcome of ESX with link"Connecting to Web Access", when I click on it I get"Internet Explorer Can t Open The Web page.
I had a look at VIM, I can see the details of the Vswitch network on the configuration page, including the IP address of the console service. Can't see how to open a service console. VIM of pointing at the address for service console is unable to do anything.
I just need to know how to open the Service console and check the tables of ARP based on the KB.
Please dumb down of your responses to me!
The fundamental problem is about some units of electric distribution that we use to power the equipment in the racks. They have a network connection which we track using Virtual Machines to the report of a third person of monitoring and control software. The virtual machines are running alarm software driver used to report to the third party. The virtual machine is on a blade server.
We have a problem where a unit of the IML has been replaced but configured with incorrect default gateway address. In the hours to do so, the monitoring and control software lost connection to ILM and one by one, all units of the IML began to send the ARP requests - "who has 10.172.248.254'.
Finally, the MDU constantly send ARP requests and the MDU have lost connectivity to the virtual computer. If we open the VM machine, follow up and a MUD, the ping command ping fails, if we put a laptop in place an ILM and ping the machine VM, the ping works fine.
If power us off/on the ILM voltage they are good, but we are a 24/7 operation and power cycling the MDU is considered risky.
We have had this problem before and the only solution was to rebuild the virtual machine and assign all MDU to a new network address.
All switches ILM is connected (foundry Falstron GS) have been verified by the support of our network guys and we are told are all good. The blade server hosts about 20 VM and they work just fine from other systems SNMP traffic monitoring.
If anyone has any ideas I'm all ears.
Hello
As stated, the console is the administration interface that you can use directly on the hardware. It is not a VM (as such) that connect you with the standard management GUI. You can SSH in the network or you can be "physically connected" as you say (I would use HP SIM or the ILO to connect directly to the blade). Once you have that screen upward, press 'Alt + F1' and you connect. Then you should be able to follow the KB to check the ARP table.
See you soon,.
-
Address IP of the Service console &; Esx server name
Hello
How to get the address Ip of the service console & the name of the ESX Server in the data center based on the cluster?
Property 'Networkinfo"of the esx server does not give advice for Service console Ip address to me.
Thanks in advance for the answer.
Try it like this
foreach($cluster in Get-Cluster){ Get-VMHost -Location $cluster | ` Select @{N="Cluster";E={$cluster.Name}}, @{N="Host";E={$_.Name}}, @{N="Console IP";E={[string]::Join(',',((Get-VMHostNetwork -VMHost $_).ConsoleNic | %{$_.IP}))}} }
-
Search for content in pdf files stopped working after the migration of Windows 2008 Indexing Service
Hello
We have designed a search custom as an aspx page that uses the Indexing Service to search for content in a set a which coexist document types (doc, pdf, xls, etc.)
We moved to a Windows Server 2003 Indexing Service to Windows 2008 and since the Indexing Service has stopped the search pdf files. The search returns only another type of pdf files.
On the new server where the Indexing Service, I installed Adobe PDF iFilter 11 for 64-bit platform, I think it's the plugin the Indexing Service uses to find the content of pdf files.
Does anyone got the Search Indexing Service content in PDFs on Windows 2008 server?
Thank you
Mihaela
Hello
Post your question in the TechNet Server Forums, as your question kindly is beyond the scope of these Forums.
http://social.technet.Microsoft.com/forums/WindowsServer/en-us/home?category=WindowsServer
See you soon.
-
HP has a URL to search for a printer authorized service center?
I have a HP2840 requiring just a little cleaning maintence work - nothing is broken. Two cases I contacted don't help out because I'm not a "business".
HP has a URL to search for a printer authorized service center?
Hello
Please click the link below to find the service center.
-
My printer does not print. I rebooted the printer, but I still can't get it to work. When I go to search for a printer in windows, it tells the domain services active directory is not available.
Hello
1. is the computer connected to the domain?
2 did you change on your computer?
3. What is the brand and model of the printer number?
4. is this a network or connected via USB printer
Method 1:
I suggest you follow the link and check.
Printer in Windows problems
http://Windows.Microsoft.com/en-us/Windows/help/printer-problems-in-Windows
Method 2:
I also suggest you to follow the link and check.
Solve printer problems
http://Windows.Microsoft.com/en-AU/Windows-Vista/troubleshoot-printer-problems
-
Update of the modules for security issues ESX service console
Today, I was asked a question on the vervsion of OpenSSH used on the service console for our environment vSphere 4.0. Apparently, there is a vulnerability in OpenSSH 5.6/7 with a certificate which has been corrected in version 5.8. My response to the security team has been we are the 4.3.p2 and as a result, this issue does not concern us. So the following questions then becomes why you are not in the latest version?
I'm curious to know if someone has already discussed with VMware on these types of security issues where the components used by RHEL, like OpenSSH, are vulnerable. What was their response to attempts to update this kind of things? I guess some of the answers would not be supported, you'll break, if you patch it's no guarantee your fix will not get downgraded, etc..
I'm looking for is a solid answer that explains why we do not have that kind of stuff to ESX, only when VMware provides the fix. I could contact the support, but I thought her first check and see what others have met.
Thank you
Hello.
I think that all the reasons you mentioned (not supported, you're going to break, if you patch it's no guarantee your fix will not get downgraded, etc.) are pretty much true. The ESX 4.1 Patch Management Guide stated in the FAQ section:
When a rpm on my ESX host has an equivalent Linux, can I use the Linux RPM to upgrade my system?
N ° VMware recommends that you update your host ESX 4.1 with RPM provided by VMware.An answer I could use would be to take a step back to look at the bigger picture. Is a SSH, which should be secluded/protected to some extent in a first time, have a vulnerability more risky than having an ESX host unstable/not supported with X number of VMS running on it.
Good luck!
-
separate the vlan for the service console and vkernel
Hi all
I need to restructure my environment uat and dev, keeping both under vcenter even. I run the machine with 4 NICs (currently using 2 each for sc + vk & vm port with eather channel gp). The reason behind this is that we have stored separately (using nfs) in uat and dev segment to be used by the servers (virtual and physical) in the respective segment. I'll take 2 clusters as uat and dev. wanted to help the same regardeing
- wanted to know if I can get my service console and vmkernel running on VLANs separate as shown below
- UAT cluster
- SC - 10.10.11.x
- VK - 10.10.12.x
- dev cluster
- SC - 10.10.11.x
- VK - 10.10.50.x
- UAT cluster
kindly let me know for further information on above, any other suggestion on above will be useful
Yes your SC and VMkernel networks running on different VLANS will work - it is a best practice.
- wanted to know if I can get my service console and vmkernel running on VLANs separate as shown below
Maybe you are looking for
-
Recovery with Satellite C850-B718 problem
My Satellite C850-B718 fell on some issues. I got it with my recovery disks. The recovery was supposed to be successful. When I restarted the laptop, it still asks me to recover. What should I do?
-
Satellite R630-141 - connect wireless 5 GHz and channel 44
I just bought a new Netgear N600 Wireless Dual Band Gigabit Router model WDR3700. In theory I can connect either 2.4 GHz or 5 GHz normal connection. I can connect correctly at 2.4 Ghz, but my Satellite can't seem to see the show of 5 Ghz. I put all s
-
HP pavilion dv6-6155tx entertainment notebook pc dolby home theater is removed
I have the pc hp pavilion dv6-6155tx laptop. My home dolby cinema is removed. How can I get it back?
-
HP Slimline s3507c: SSD in HP Slimline s3507c mounting
Hello Anyone know what type of mounting brackets, I need to buy to put a SSD 2.5 "in a HP Slimeline s3507c? The SSD is 2.5 "and the drive Bay hard 3.5" pull-out. If you visit this webpage, http://support.hp.com/us-en/document/c01050020and scroll down
-
Wireless Laser Mouse 5000 Windows 7 64-bit installation challenge
Wireless Laser Mouse 5000 Windows 7 64-bit installation challenge continues to get customer assistance contact support when you try to load the software to control the mouse buttons and the speed of response. Suggestions?