Server cerificate PKI in the network script: EEM DMVPN

Similar Questions

• Reoprts itdrep server already exists in the network

  Hello
  
  I have two AIX machines with different host names and server application independent of 10 gr 2 installed on both machines. I created a new report server with the name "ITDREP" on both machines (same name on both machines).
  Now when I try from the report server on the Computer1 it starts but after that if I try to start the report server on computer2 it fails with the error "Reoprts itdrep server already exists in the network.
  
  If I want to have a server of reoprt with the same name on both machines, what should I do?
  
  
  Concerning
  Ankit

  As you can see, the port = "14021' for the multicast network.
  If you specify on the second server port = "14022" then you can use the same name reportserver on both servers.
  Only downside is that you can send requests to report from the first server (to the help of run_report_object rwservlet, rwclient or forms) to the reportsserver on the second, but this isn't a problem if you have set up 2 servers identical for purposes of distribution of the load or high availability.

• After the Server 5.1.5 upgrade network user cannot connect by most workstations

  Hi all

  Intro

  I upgraded one of my client of 10.6.8 Xserve server at El Capitan / app 5.1.5 server.

  The server is configured with the network homefolders and mobile homefolders. We also use PCS. The 10.6.8 configuration has worked perfectly and still doesn't work. But now it is time to move on.

  The upgrade process from was relatively smooth. I had to configure the interface network again, then check DNS (front / back) and I also had to re - install the SharePoint, including network sharepoint (via AFP) houses.

  Problem:

  Then, I started to test the connection as users of the network on client computers. I found that it was not possible to connect from most client computers.

  After entering the login credentials was refused immediately. As is the case when entering the incorrect credentials.

  On client computers, nothing has changed.

  Client computers running Yosemite 10.10.5 and some are running 10.6.8

  As soon as I reboot the Xserve 10.6.8 original that's all is back to normal.

  What does not work:

  Those who connect has worked well:

  • Mobile sync (on Unassigned Computers)

  • Log is as user network at home (on Unassigned Computers)

  • PCS worked fine. New settings have been made correctly. On all computers.

  • Automatically install some actions has worked well on all computers. It is a local administrator on the client computers. When connecting to the account, the network shares are mounted using PCS.

  • Resolution of the DNS of all client computers

  • DHCP works OK

  • Client computers running 10.6.8 seem to be not affected.

  At one point one of the workstations involved that did not work, started working.

  What I tried and not solve the problem:

  • Renew DHCP client

  • Removed liaison OD and put in place again

  • Trashed records managed preferences (these have been re-created correctly)

  Ideas on possible causes:

  The most logical causes of this behavior might be:

  (1) client computer cannot find the master OD.

  (2) the powers of negotiation fails.

  Since the Division of the OPPOSITION binding work, works PCS etc., the client computer is the master of the OD.

  The latter seems the cause more lickely. Ticketviewer does not show tickets. Ticketviewer by using the credentials of a user of OD manually requesting a TGT works very well.

  All advice is appreciated.

  Kind regards

  Nico

  Hi Nico,

  Maybe the problem is related to the AFP. Have you tried disabling AFP in Systempreferences and delete all shares. After this restart AFP and try to add shares again. Have a look at the access privileges. It is urgent to remove and re-add the userfolders on the server share.

  Good luck

  Peter.

• BMR in WINRE will not restore the backup to the network drive.

  We are currently in the testing phase of DPM 2007 deployment for Windows Server 2008 backup.

  DPM backup on Windows Storage Server 2008 correctly on the network attached to the DPM server drive.

  The Windows Storage Server 2008 I shot the current hard drive that was working properly (500GB) the computer and replaced by a 1 to.

  I started the machine with WSS2008 drive, in the CMD prompt, I enter the following command:

  1) x:\ > start /w wpeinit
  2) x:\ > wbadmin get versions - backuptarget: \\SANDSHREW\serverbackup$
  3) x:\ > wbadmin start sysrecovery-version:11/03/2012-18:04 - backuptarget: \\SANDSHREW\ServerBackup$ - recreatedisks

  I should mention that when I run 2 and 3 he asks me the login for the server sandshrew.

  The error I get on 3 is:

  The Meadow (System ASR) recovery automated system restore operation failed.
  The parameter is incorrect.

  I played with this for days now, any help would be greatly appreciated :)

  Thanks a bunch,

  Geoff

  Hello

  Thanks for posting your question in the Microsoft Community.

  The question you posted would be better suited in the TechNet Forums. I would recommend posting your query in the TechNet Forums. You can follow the link to your question:

  Windows IT Pro Forum 2008:

  http://social.technet.Microsoft.com/forums/en/windowsserver2008r2general/threads

  Kind regards.

• Windows 2K 3 is removed from the network, every hour, sixth of its previous disconnection

  Hi all

  I have a problem here in a production environment. We use the combination W2K3 SP2 and SQL 2008. It is the server gets disconnected from the network, every hour, sixth of its previous logout. SQL resources are working well, but the server itself becomes not accessible. When I mean the server by its IP address or name DNS etc.

  While closely watching the issue, we found that even the RDP connection to it expires exactly at the same time. It's just an interruption of 10-30 seconds, and after him, everything is normal. Only clue is, it happens exactly every sixth hour. We also found his happens for all servers in the VIRTUAL local area network at the same time.

  Sixth hour that I mean, is the model... for example it happes to 09:15 then it will happen about 15:16 and then 21:17, then new tomorrow 03:18, 09:19, 15:20, 21:21 etc. If this isn't exactly every six hours, it every hour, sixth of its previous logout. The calendar is always in motion.

  Note:

  DHCP is not enabled on the server. Its configured to use a static ip address. The server is based. No DHCP server in the environment.
  Client DHCP is running on the machine to register DNS for the DNS server. No windows firewall is turned on.

  So its more like a configuration problem which is something set up to do something every time sixth from his previous instance.

  Please let me know if you think anything.

  Thank you
  Damien

  Hello

  We have a separate Department of Microsoft who work with servers. Thanks for posting your query in the link below:

  http://social.technet.Microsoft.com/forums/en-us/winserverfiles/threads

  Thank you

• need for server 2008r2 Pavilion p7-1000 network card driver of (tried win7 drivers N.G.)?

  Hello

  I'm trying to install the server 2008r2 on the HP Pavilion p7-1000, has four cores amd 64 bit cpu, 8 GB ram, 1 TB hard drive.   For some reason I can't seem to locate the drivers for the NIC realtek.  Of course, I'm pressed and trying to accomplish something in a single day.  And many other things at the same time.  I never thought that this Server 2008 would have a problem with a common network card.

  Someone has a direct link to a kind of driver that works with this?  I tried to go to the realtek, and perhaps I simply downloaded the wrong software.  But what I 'As' on their part, did not work.  I tried a "auto-install" program, but also what I THOUGHT it was the real Server 2008 drivers for the network card.

  Thanks for advice and guidance

  Hello:

  Have you tried this one directly from Realtek site?  a 3rd on the list... According to this record in the series, they have 8105E card.

  http://www.Realtek.com.tw/downloads/downloadsView.aspx?langid=1&PNid=14&PFID=7&level=5&Conn=4&DownTypeID=3&GETDOWN=false

  Paul

• Configure vCenter as orchestrator 4 everything configured correctly, but the network. Failed to save config

  I'm going through my first vCenter Orchestrator configuration. I started following configuration directives in order. I logged in the vCenter Orchestrator Web Configuration utility. One of the first things to do is set the network on the server. I entered the network tab and click on the drop-down list to select the IP address of the host. This is where even 127.0.0.1. I chose the IP address of servers and it fills correctly in the DNS name with the full domain name field. Now it is supposed to be an Apply Now button that comes silence... but it doesn't.

  I left all the port settings on this page to the default value. I can click on the tab SSL and am able to import the certificate from the server vCenter without problem. All other aspects of the configuration has been completed (LDAP, database, server certificate, license) but I can not save the configuration of the network and bind to the network adapter. So I'm stuck. It is the last part of the initial configuration that will not end. Any help would be great.

  The Apply Now button has been available on any necessary location during installation.

  It's a virtual machine with Server 2003 Enterprise R2 SP2, SQL 2005, 2 GB RAM and 1vCPU

  Nothing else installed on this server

  vCenter Orchestrator Build 4.0.0.4240 a vSphere vCenter server connection

  I saw once in my configuration when I am struck by the console configuration page and the resolution of the console has been set to 640 x 480.  In this case, apply the button was hidden.  In my view, that we do guarantee that this higher such as 1024 x 768 resolutions.

  Could you confirm that this is not the case (you use the browser in a context of low resolution?

  Thank you

  SIA

• helps the network planning

  Hi all

  I'm new to Vmware and I'm still in the process of documentation, but I'm trying to accomplish a vmware infrastructure network.

  I have the following equipment:

  Dell Equallogic PS6000XV reference - SAN - 4 network cards

  2 x Powerconnect 6224 24 GBE, managed switch ports

  1 x PowerEdge 1950 1U Quad Core Xeon with 4 GB of RAM - Vcenter

  3 x 2U PowerEdge 2950 2 x Xeon Quad Core with 64 GB of RAM - 2 x quad NIC - + 2 for ESX

  VMware Enterprise Edition (acceleration of medium kit)

  On this basis, I intend to use 3 VLAN on the physical switches, as follows:

  pSwitch - vlan goal - vSwitch

  VLAN 1 - production network (SMV) - vSwitch0

  VLAN 2 - iSCSI and vMotion traffic - vSwitch1

  VLAN 3 - vCenter and ESX management - vSwitch2

  In the idea of having a redundant network, both switches will rising fiber optic, and I decided using the following distribution of NIC

  SAN - will have 2 NICs connected to each switch

  ESX - 2 NIC - vlan3 - SC and embedded network management

  -2 network - vlan2 - iSCSI and vMotion network cards

  -2 network - vlan1 - production network (VMs) cards (I know I can use more than 2 cards network here)

  Please correct me if I'm doing something wrong.

  Also, I guess the vCenter system must have 2 network cards, vlan3 connected to one, to manage the ESX host and another, connected to the vlan1, in the production network, having a public IP address where I can connect remotely. Is this good?

  Thank you.

  Hello

  As suggested earlier, it is better to make a DMZ back to back to place your guests & vCenter behind him, after that you can activate TCP 3389 RDP of your production to vCenter server that is behind the firewall.

  I did the same excactly of installation:

  • 4 guests, double each with 20 GB of ram, 6 natachasery, 2 GHz Dual-Process 3.0 & unique FC HBA Ports.

  • • 2 natachasery for SC, vMotion & vCenter

    • 2 natachasery for Production

    • 2 natachasery of DMZ

  • I created a VLAN Trunk on my Clustred pSwitches and devote vmnic0 & vmnic1-> vSwitch0 and I activated the physical labelling on the ports.

  • • vmnic0 connected to pSwitch1 & vmnic1 connected to pSwitch2

    • on vSwitch0, I created 3 exchanges

    • • Service Conole

      • vMotion

      • vCenter

  • After connecting guests to the SAN, I created 2 VMs, 1 for vCenter and 1 as a MS ISA Firewall, both mapped to vCenter exchanges

  • • I assigned vNIC MS ISA Firewall 2, 1 of vCenter and a Production PortGroup, so I can get proper routing and Natting to join two networks via required limited ports controlled by MS ISA Firewall, now assuming that you know how to set up a back to back firewall

    • I welcomed only RDP to vCenter Server ESX network production.

  • To get rid of DNS and other issue of stuff, I configured the server vCenter Server as a DNS server for all of the network which is at the origin of the production. So the ESX host can get name resolution.

  This Setup works perfectly without any problems, but I think I would suggest, is not to use the virtual Firewall why? because you will need to open another port for your server to backup if it is put in your production network, NTP server, ect ect. As soon as the load on your network of ESX, you will see the virtual firewall eats a lot of CPU and memory resources. That's why I intend to change this firewall with a Firewall physical, to acquire the resources for something else.

  Do not build your Setup program and subsequently change your archticture network, once you change your configuration, you will need to disconnect your hosts on the network that translates = towards the bottom of your VMS losing services.

  Best regards

  Hussain Al Sayed

  If you find this information useful, please give points to "correct" or "useful".

• Problem SQLDEVELOPER the network adapter could not establish the connection

  Hello I have a strange problem with SQL Developer (2.1.63) under Linux (Debian-testing-squeez/sid) version of the version: java java "1.6.0_16.
  Java (TM) SE Runtime Environment (build 1.6.0_16 - b01)
  Java hotspot Server VM (build 14, 2 - b01, mixed mode)
  
  Java is a debian .deb (sun-java6-jre, sun-java6-jdk).
  Whenever I try to connect to a database running on the remote server, I got error the network adapter could not establish the connection.
  (connection to base and also tnsnames connection)
  Sqlplus on the same machine works very well with the same connection settings, I also try the same SQLDEVELOPER version in the windows box and I had no problem with the connection.
  
  what I tried:
  1. in the course of running tcpdump eth0 dst db01x-i on the client and I don't got no network traffic going out of the box
  2.i have also tried tcpdump - neither eth0 host 192.168.3.9 and port 1521 on the server database to be sure, but also no traffic
  3. put the database server in/etc/hosts nothing change
  4. change the level of logging of the SQLDEVELOPER, but no significant errors
  5 different versions of the jdbc (ojdbc5.jar, ojdbc6.jar) connector
  
  I'd appreciate any help in this topic.
  BR and thx Thomas

  This problem is probably with java networks interacting with a new parameter to the default kernel in Debian. Among the bugs identified on this is here - [http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=560056]
  Two things to try, from various bug reports, are
  (1) "echo 0 >/proc/sys/net/ipv6/bindv6only ' and make this change permanent if it works
  (2) edit {sqldeveloper home}/sqldeveloper/bin/sqldeveloper.conf and add the line}
  "AddVMOption - Djava .net .preferIPv4Stack = true '.

  Jean Paul

• Script to add a domain user to the local Administrators group raises the error "the network path is not found."

  I have a Windows Server 2008 R2 domain and a Windows XP Pro workstation that has been attached to the domain and then disconnected. I am trying to create a VBS script to add a domain user to the local Administrators group.

  I log on my computer as a local administrator and run the following script:

  Dim oNetwork: Set oNetwork = WScript.CreateObject ("WScript.Network")
  StrPC Dim: strPC = oNetwork.ComputerName
  Dim OGroup: Set oGroup = GetObject ("WinNT: / /" & strPC & "/ directors")
  Dim OUser: Set oUser = GetObject ("WinNT://domainname/username")
  oGroup.Add (oUser.ADsPath)

  This script returns the error "the network path is not found."

  However, I am able to go into control panel > user accounts > enter the user name and the domain name > click Next... > choose the administrators of the 'other' group and the user name will be added to the local Admin group.

  The same script runs without error if it is launched after logon on the workstation with a domain administrator account.

  How can I get my script runs without error, when you are logged into the workstation as a local administrator?

  Best regards, Andy

  The code that I used came from here. If the syntax of the Add method is passed to oUser.ADsPAth to "WinNT: / /" & domainname & "/" & username, the script works correctly.

  Therefore, the modified script:

  Dim oNetwork: Set oNetwork = WScript.CreateObject ("WScript.Network")
  StrPC Dim: strPC = oNetwork.ComputerName
  Dim OGroup: Set oGroup = GetObject ("WinNT: / /" & strPC & "/ directors")
  Dim strUser: strUser = "WinNT://domainname/username."
  oGroup.Add strUser

  Thanks to Qasim Zaidi to show the code of work here.

  Best regards, Andy

• Pavilion p7 - 1227c needs the network drivers that work with Windows 2008 server R2

  I bought this new Pavilion P7 - 1227C at Costco so that I can install Windows Server 2008 r2 with Hyper-V role

  I managed to install Windows 2008 server but unable to t the wireless or ethernet to work.  I tried to use the driver 64 bit Windows 7 without success.

  I think return Costco if I can't get the network driver that will work with Windows 2008 Server R2

  Thanks, in advance.

  Tour37

  Hi Paul,.

  Thanks for the link, I was able to download AR816X_V.0.14.15_WHQL.

  The driver works for Windows 2008 Server R2.  I just need to find the drivers for the wireless card.

  Best regards

  Round 37

• What are the network requirements for the remote server of the Panel?

  What are the network requirements for the remote server of the Panel?

  I tried for awhile now to set up a Control Board.  I can connect to my remote panel of computers from other computers on my local network but nowhere else.

  Whenever I use web publishing tool gives me a URL in this format: Http://Computer-Name.Corporate-Name.local:8086 / VI - nom.html apparently it means I have a local DNS server and this URL is meaningless to the public.

  When I try to connect with the Operate > Connect to... remote control, I get this error message:

  "Connection to Server remote panel...".
  "Connection refused by the server remote control specified: make sure that the LabVIEW Web server is enabled on the specified server.

  I got the same error when I tried to host a remote panel from my laptop at home, on my Wi - Fi.  Is there some network settings or firewall I'm not seting?  Would it be my server or the router or the private network?

  My goal is to be able to host remote panels of my laptop while I'm on the international scene, creating using 4 G internet mobile.  Is it still feasible?

  As he Turners on my router had to be put in place so that my Port is in the rage of transfer.  Also I had to disable DHCP.  Without that you cannot host behind a router.

  These are the instructions I put fallow:http://digital.ni.com/public.nsf/allkb/B1E9A3D78BAED949862573AD0065D4D2

• TCP on PC server with the network interface has 2

  If I need to create a TCP on PC server with the network interface has 2 with a different IP address, for example 192... and 172... and the IP address of the client side is 192..., is there something I need to take care.

  Any suggestion, thank you.

  No, by default the server listens on all interfaces.

• Keep the network discovery settings after you restart the Server R2 Standard 2012

  Hi all

  I'm having the following problem. After you restart the server from the network discovery will go off. Therefore, I do not see the server, this can cause problems in the future, so I need to know how to keep on even after network discovery settings server restart.

  Thanks for the help!

  Hi, manual,.

  I suggest you post your query in the following forums to improve assistance in this regard.

  https://social.technet.Microsoft.com/forums/WindowsServer/en-us/home

  Thank you.

• How to restore the network icons and properties on Windows server 2008

  Original title: network properties

  What is the best way to restore the network icons and properties on Windows server 2008.  The properties of network share folder is empty and the internet icon is missing as well.

  Hi Mitch,

  I suggest that you post the application on Microsoft TechNet forum because we have experts working on these issues. You can check the link to post the same query on TechNet:

  http://social.technet.Microsoft.com/forums/WindowsServer/en-us/home

  Please do not hesitate to contact us if you have other questions related to Windows.