set the duration for the nor 6501 to control relay

Hi all

I made great progress thanks to your help. Now, I know how to control the relay using NI 6501.

Furthermore, I try to put in place a period of time (after two hours) and leave-6501 OR turn on the relay.

What kind of example I can refer to?

When pressure data are weak to 1mtorr, then turn on the relay is another control.

If there are some I can refer to similar examples, it will be useful for me to programming

Thank you

Tags: NI Software

Similar Questions

Set the value of cluster control in secondary school

Hello

Is there a way to set the value of control from one cluster to a high school?

I enclose my screw in LV8.0

Charly

If you have a reference to the VI being put into secondary (which there or it is not in the secondary, right?) you can use it to get a reference to the façade of the VI. This in turn will allow you to read an array of references to all the controls and indicators on the front of the Secondary VI. Cross this table by looking at the text property of the label: for each reference in the table until you find the one for the control of the cluster.

Now, use the specific function to more class to convert reference generic control of the pole to a cluster reference. You can use it to get an array of all the controls within the cluster. Now, go through this table by looking at the text property of the label: for each reference in the table until you find the one for control quevous want to set and you are there...

Mike...

How to set the type default XControl 'control '?

Hi all

LabVIEW 2009 + DSC

How can I configure the type default XControl be 'control '? For example when I drag and drop the Xcontrol VI project is always kind of indicator, and I want it to be a control. Of course I can change it manually after a fall, but when there are many XControls that takes time.

BR, Jim

In the façade VI you can get the "change management event" uses the following code to be an "indicator only.

The same code can be used in the init State.

Tone

How to set the delay between 2 controls

I do two tests.

I want to run first test

After 5 sec run 2nd test. How to do this?

I play small preloader in that mouth of time 5 sec?

Code:

//OS Version Test

osVer.text = Capabilities.os;
osResult();
function osResult():void
{
          if (osVer.text == "Windows XP" || osVer.text == "Windows 7" || osVer.text == "Windows Vista" || osVer.text == "Mac OS X.Y.Z")
          {
  Pass1.visible = true;
  Fail1.visible = false;
          }
          else
          {
  Pass1.visible = false;
  Fail1.visible = true;
          }
}


// Screen Resolution Test

screenRes.text = (String(Capabilities.screenResolutionX))+ " x " +(String(Capabilities.screenResolutionY));
screenResResult();
function screenResResult():void
{
          if (Capabilities.screenResolutionX >= 1024 && Capabilities.screenResolutionY >= 756)
          {
  Pass2.visible = true;
  Fail2.visible = false;
          }
          else
          {
  Pass2.visible = false;
  Fail2.visible = true;
          }
}

It is deprecated but still used and it is easier than a timer:

import flash.utils.setTimeout;

NOTE: do NOT put in brackets at the end of the function name.

setTimeout (screenResResult, 5000); Run screenResResult() after 5 000 milliseconds (5 seconds).

Text caption disappears after 3 seconds, even if by default is set to keep for the duration of the slide.

On each slide, I have a different title in the upper right. I noticed that they disappeared after a few seconds, I went into preferences and set the default value for the text caption, image, etc. to stay for the duration of the slide. But when I go to test it, they disappear after three seconds still.
I'm doing something wrong?
Thank you
Arthur

... and if you do not override the style of titles, using the small arrow curved in the upper right of the accordion of Timing will allow you to propagate the change of one legend to all others with the same style.

When I set the duration for a timelapse, how can I add breaks is not fluid. for example, it removes frames per second. THX

Casey Neistat made in some of its opening timelapses.
I don't know how to set the time at 500% etc. that reveals a 'speed up' fluid video, but I have this where 'he' so every second or chopped both frames are removed
Here is an example, I think: Cadet Vlogger - YouTube World (12 seconds in)
Thank you

Try to add the posterize time effect after you have accelerated the clip.

See you soon,.

Jeff

iMovie 10.1.1 set the duration of the clip of stills

Haven't tried Google or none this result. It seems that Apple continues to change it from one version to the other. I use iMovie on Mac OS - X 10.11.3 10.1.1. I'm taking about 380 still images and create a stop-motion video. I want each image to play for about 0.1 seconds. When I imported the image he set the duration of the 10 seconds for each clip. I thought it would be easy to change after the fact. May not know how! Thanks for any help.

In turn should I use different software for this task?

Select all your still images in the timeline and click the information above the observer (little "i" in a circle). Enter the length desired in the "Time" box and press return. The shortest time setting seem to be 0.2 seconds.

Geoff.

CAN´t set the duration of an appointment in the iCloud between Outlook 2013 calendar

Hello, I have can´t set the duration of an appointment in the iCloud calendar between Outlook 2013, when I want to set the time, it just made me put ¨am¨, I can´t create it after midday (¨pm¨).

Hope someone of you can help me.

THX

Hey Bernaragon,

I understand that you are having problems with the creation of a calendar to your iCloud account in Outlook. Let's see if we can get smooth it.

For most of the problems with iCloud for Windows can be solved in two steps of troubleshooting. The first being to toggle synchronization of calendar and then put it back in the iCloud for Windows app. The second being would ensure that the Add on Outlook to iCloud is turned on. Take a look at the article below for more details on how to do these steps.

Get help using Outlook with iCloud for Windows
https://support.Apple.com/en-us/HT204571

Let me know helps fifths.

Take it easy

Set the scale of thermocouple at table for a channel in the task

I create a task that contains 9 measures voltage and 10 by thermocouple programmatically. All the thermocouples are of Type T. I just want to read one of the thermocouples up to the limit of 30 k. NOR for the Type T is 73 K.

I understand that the lira below their limit thermocouples OR is to change the scale type to table using a property DAQmx Channel node. However, because I take different types of measures, I need to isolate the channel particularly thermocouple. If I move the entire task to the node property DAQmx channel and try to set the scale of the type of thermocouple to table, I get an error because the voltage channels do not support this property. I can't understand how to get individually on channels of the task. I don't want to separate the measures into two tasks, because then I have to do to synchronize the clocks of additional programming.

I have more than one idea: use a DAQmx create task VI at the beginning. Do a global virtual channel to MAX for the thermocouple that I want to change the type of ladder for. Place a constant for this virtual channel and run through the DAQmx Channel property. Use the task of creating DAQmx to create a task containing this global virtual channel. Pass this task to a bunch of DAQmx create Virtual Channel screws to add other measures to the task.

This makes a lot of the scalability of my program and seems to be the wrong shape in general. Looks like there should be an easier way to do it. Any ideas? Thank you!

Hello

Try to use the property node of channel Active channels (ActiveChans) that is by specifying the string "isolated" as its input, and then adding the (HAVE. Themcpl.ScaleType) in developing the property node even by setting its entry. The property node Active channels specifies a list of virtual to change channels or virtual channel. Virtual channels are in a specific job. NOR-DAQmx configure all channels in the task if you do not set this property

Best regards

M Ali

Technical sales engineer

National Instruments

How to correct for IQ rates which are not supported by the NOR-2920?

Hi all;

I use Labview 11 and the NOR-2920 (Ettus Radio) to build a FSK receiver, I the Modulation toolkit.

My carrier is 169 MHz, my flow is 256Kbits/sec, my tour of frequency is around 89. 5 kHz, I choose a 16, my symbols FSK samples/symbol is 2 (0-1).

My receiver is close to work, however, I am getting an extra of 5 bits in my 408 bits frame data.

My sync bits are all the tail and the front end of my frame data which has also a meter 16-bit images on the front of the frame, which runs from 0 to 65535 without losing data.

I think that the extra bits are the result of rate IQ I try to set to 4096K based on 256 K * 16 = 4096 K

The radio seems to default to 4,166667 M for the rate of IQ.

The ratio of 408bits /415bits = 4096/4166 coincidence or not?

Is there a way around this problem in the configuration of the NOR-2920 or how I manage the sampling and recovery of data.

Any guidance would be greatly appreciated.

Don3of4

All interested for:

The answer is Labview a an I / Q resample module.

Connection between the extraction of radio and the demodulation modules, set the sampling frequency entry real want = rate * of the data samples / symbol.

Work so far, don't know what is happening when other tolerances overclocking begin to influence the data, but for now his work. Also don't know why this is not incorporated into the receiver or the fetch modules for sampling rate that you actually need from the beginning but I'm still learning.

Don3of4

I'm doing slideshows to music with an opening, I would switch to LR, but you cannot set the duration of each slide (in my case the score) based on listening to the music. (In the opening by clicking on the "stopwatch" and pressing enter at each change of

I'm doing slideshows to music with an opening, I would switch to LR, but you cannot set the duration of each slide (in my case the score) based on listening to the music. (In the opening by clicking on the "stopwatch" and pressing enter at each change of image). Adobe staff question: can I expect to find this option in a future release?

Hi Pcaubi,

There is no such updates for the same from now.

I suggest you to please put in a feature request to: Photoshop community customer family

Kind regards

Tanuj

Set the type of array on the duration... Get the error...

My requirement is
I try to set the table on the duration type. that is ortf_in_table_tbl {noformat} ({noformat} i).field_position_rec.ortf_segment_field_name to the code below.

But when I'm running code below and get below error:

DECLARE
   CURSOR field_position_cur (p_table_name VARCHAR2)
   IS
      SELECT xosf.field_name, xosf.starting_position, xosf.field_length
        FROM record_types xort, record_segments xors, segment_fields xosf
       WHERE xort.record_type_id = xors.record_type_id
         AND xors.record_segment_id = xosf.record_segment_id
         AND xosf.table_name = p_table_name;

   CURSOR raw_data_cur
   IS
      SELECT *
        FROM raw_data;

   TYPE raw_data_typ IS TABLE OF raw_data_cur%ROWTYPE
      INDEX BY BINARY_INTEGER;

   TYPE table_typ IS TABLE OF emp%ROWTYPE
      INDEX BY BINARY_INTEGER;

   table_tbl      table_typ;
   raw_data_tbl   raw_data_typ;
BEGIN
   OPEN raw_data_cur;

   LOOP
      FETCH raw_data_cur
      BULK COLLECT INTO raw_data_tbl;

      EXIT WHEN raw_data_tbl.COUNT = 0;

      FOR i IN raw_data_tbl.FIRST .. raw_data_tbl.LAST
      LOOP
         FOR field_position_rec IN field_position_cur ('EMP')
         LOOP
            table_tbl (i).field_position_rec.field_name :=
               SUBSTR (raw_data_tbl (i).raw_line_text,
                       field_position_rec.starting_position,
                       field_position_rec.field_length
                      );
            DBMS_OUTPUT.put_line
                    (   'table_tbl (i).field_position_rec.field_name '
                     || table_tbl (i).field_position_rec.field_name
                    );
         END LOOP;
      END LOOP;
   END LOOP;

   CLOSE raw_data_cur;

FORALL i IN table_tbl.FIRST .. table_tbl.LAST
      INSERT INTO emp 
           VALUES (table_tbl (i)
                  );
   COMMIT;

EXCEPTION
   WHEN OTHERS
   THEN
      DBMS_OUTPUT.put_line ('OTHERS ' || SQLERRM);
END;


**ORA-06550: line 61, column 52:**
**PLS-00302: component 'FIELD_POSITION_REC' must be declared**
**ORA-06550: line 54, column 13:**
**PL/SQL: Statement ignored**

Here field_position_cur gives me the name of column for the table EMP (i.e. field_position_rec.field_name) and field_position_cur give start and length to calculate the value of the column
i.e.

 SUBSTR (raw_data_tbl (i).raw_line_text,
                       field_position_rec.starting_position,
                       field_position_rec.field_length
                      )

But it gives me error. We're on the 10g database.

Please suggest the solution for it.

Published by: BluShadow on January 12, 2012 08:21
addition of {noformat}

{noformat} and other tags to make it readable.  Please read {message:id=9360002} and learn to do this yourself.

Yes. Really recommend do you the suggested and especially medium provided the code and dynamic linking and loose curls.

How can I set the password for iPad 2 Air to something else than "immediately"?

I have three iPad, iPad 2, iPad 2 Air and tha iPad Pro.

My iPad 2 Air gives me the option to "set the password immediately".

the other two iPads give options, for example, 15 minutes, 1 hour, etc.

All three iPads running the latest IOS.

is this a glitch with my iPad 2 Air or are they all like that?

Why the 'immediately' is the only option? It looks like the other options are missing.

Thank you.

Try the help in this support article > using a password with your iPhone, iPad or iPod touch - Apple Support

set the password for the 'parameters' on iphone 5

Y at - it app to set a password for the "parameters" on an iphone 5? My son continues to change some of the parameters,

N ° define a word password on the phone and don't let not your son play with him.

Set the font size for the menu items and content of the label tab?

Old eyes, small fonts.

I can manage the fonts/zoom for the content of the site. SITE OF FONTS ARE NOT THE PROBLEM.

Y at - there a way to set the font of the browser settings in: config to control the fonts in the BROWSER MENU ITEMS (view file Edition... etc) and TAB TITLE (TEXT) CONTENT?

PS - Keep us ordinary mat canned. A simple 'no' or 'Yes' with simple details of relevant about: config entries, would be nice. GREAT access to the most COMPREHENSIVE list possible would be on: configuration settings

You keep it as the 'EASY' button, I take it? Ever have something like this for Thunderbird, now I feel a little stupid for not connecting the dots. Thank you.

PS - just in case... Got a list of about: config options?

set the duration for the nor 6501 to control relay

Similar Questions

Maybe you are looking for