setting disable announcement of the ring 'verizon wireless '?

Similar Questions

• I can't find instructions on setting up or using the keyboard Microsoft Wireless Comfort 1. 0a.

  I can't find instructions on setting up or using the keyboard Microsoft Wireless Comfort 1. 0a.  I GOOGLED it but the only reference I find tells me to go to the download page on the Microsoft Web site for this product.  I went to this site and the only thing it is limited warranty info and Product Guide.  I downloaded the Product Guide, but it only covers the basic information like it do not immerse in water, do not take part and the various regulations of the FCC about the product.  There is no info in this guide on how to configure or use the keyboard AT ALL.  Guidance on how to use this product is probably somewhere?

  The dongle is not plug it into the keyboard, it plugs into the USB port on the computer.  Wireless keyboards is not related to them - think of that.  :-)

  If you are missing parts to the keyboard, I would just buy a new one.  You can buy wired keyboards for as little as $4 these days, wireless are a little more expensive of course.  Personally, I find the wireless keyboards to be a pain because the batteries always come out in one in-opportune times.  YMMV

  Good luck.

• Iphone4s with Skype will not take the call, it's as if the ringing type is set to zero, it gives a busy year.

  The iPhone running Skype, will not take a call, it's like the ring time is set to zero, it takes callers I would but gives the caller a busy year, any help please, thank you Ken

  I had the same problem - fixed it:

  https://support.Skype.com/en/FAQ/FA10981/how-do-i-delete-my-shared-XML-file

  Make sure that you log out of Skype on your iPhone and PC. After you delete the file, restart Skype on your computer and connect to recreate the file. The journal of Skype on your computer and in to Skype on your iPhone.

• Connection to the internet using a Verizon Wireless router

  I have a Compaq Presario CQ60-210US running Vista 32-bit Service pk2 with an Atheros AR5007 802 Wireless card. 11b / g. I have problems to connect to the internet through a router with WPA-2 Verizon Wireless. I can connect to the wireless router, but it will not connect to the internet through it. I am able to connect wirelessly through other routers wireless without any problem. All solutions?

  Problem was with the wireless card Atheros who need an updated driver. Found a newer driver on a Czechoslovak website. Downloaded and intalled and solved the problem.

• Re-establish the connection to the router from Verizon Wireless

  I use IE6 on a portable Toshiiba with Windows XP. Our internet connection is via a Verizon Wireless router. Today, I can't run (Firefox or IE, by the way) - it does not detect the router. I am still able to connect to this router and internet through my MacBook Pro. How do I reconnect?

  Thank you.

  Hello

  1. What is the model of the router?

  2. you get any error message?

  3. don't you make changes to the computer before the show?

  Please follow the steps below.

  Method 1:

  Follow the steps from the link below.

  http://support.Microsoft.com/kb/870702

  Method 2:

  Follow the steps from the link below.

  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

  Method 3:

  Follow the steps from the links below.

  http://www22.Verizon.com/support/residential/Internet/fiosinternet/networking/setup/vzmi424/120519.htm#

  http://www22.Verizon.com/support/residential/Internet/fiosinternet/networking/setup/vzmi424/120527.htm

  See also the below mentioned link.

  http://www.Microsoft.com/athome/organization/wirelesssetup.aspx

• WIFI disabled on windows vista and cannot wireless connect to the net

  WIFI disabled on windows vista and cannot wireless connect to the net, but bluetooth wireless Wi - Fi and fine switch is activated. Have a problem with ISATAP #5 who is incapable of solving that can be bound.

  All of a sudden I lost my internet connection wireless and I am unable to return.  May be because recent windows update.  Error messages on the wireless assistant say WLAN offshore or disabled.  I have tried every fix.

  In device Manager (under network adapters) shows also that MS ISATAP disabled with "Windows cannot load driver (Code 31).  When I try to update the driver, "Best driver already installed" appears.

  Is there a way to FIX?

  http://support.Microsoft.com/kb/932520

  Read the above re ignore this error message.

  Go to the website of the manufacturer of your computer/laptop > drivers and downloads Section > key in your model number > look for the latest Vista drivers > download/install them.

  See you soon.

  Mick Murphy - Microsoft partner

• I'm having the problem of local connection on my Dell PC with Vista. ISP is Verizon FIOS. FiOS representative told me to disable Ipv6 and the problem stops. Is this correct?

  I'm having the problem of local connection on my Dell PC with Vista. ISP is Verizon FIOS. FiOS representative told me to disable Ipv6 and the problem stops. Is this correct?

  original title: local area connection problem

  Hello

  1. What is the exact problem you are facing with local connection?

  2. how many computers have you plugged into the network?

  Please provide the information of network event logs to help you best.

  Click on the link below.

  http://Windows.Microsoft.com/en-us/Windows-Vista/using-Windows-Network-Diagnostics-event-logs-to-solve-network-problems

  In the meantime, run the troubleshooter mentioned in the link below.

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-network-connection-problems

• Driver is not intended for this platform (install the latest driver for Verizon Wireless WAN (UNDP))

  Hello

  My Verizon Wireless WAN has worked on my T500 (2081CT 0, 4 GB of RAM, Windows Vista Business 64) since I received it last September. This morning it stopped working. Said that the card has not been activated. Ask Verizon and Lenovo have been pretty useless - each blamed the other, I so put on my own.

  -I uninstalled the driver for the Qualcomm HS USB card integrated, downloaded the latest version of the driver (transferred via CDROM since I can't connect to this laptop to the network where I work) and tried to install it. The HS-USB card is now displayed in the devices as "Unknown device" Manager (under 'other devices'), and his device status is:

  "The drivers for this device are not installed. (Code 28)

  Driver is not intended for this platform.

  To reinstall the drivers for this device, click on reinstall the driver. »

  Huh?

  Of course, reinstall driver does not work, the first problem is that he can't find online because I don't have internet connection without the card.  This driver has been installed from the following link:

  http://www-307.IBM.com/PC/support/site.WSS/document.do?lndocid=MIGR-69999

  Seems to me that it should work on this machine. What I am doing wrong?

  -Some additional background: I've had several accidents recently, including at least two yesterday with blue screens. Easy to believe something has become corrupted, that's why I tried to uninstall and reinstall the driver.

  Help!

  Thank you very much.

  Solution was to uninstall the 'unknown device', search for new hardware and follow the promts by selecting all default values.

• Classic BlackBerry Verizon Wireless with the new classic of B.

  I am a Verizon Wireless customer for more than 25 years. Also, I'm a Blackberry user for the same time.  I've been dying to get new Balckberry classic, however, told me that Verizon does not her due to a type of different network transmission or something like that. This, it is not compatible with their network.

  I'm very, very sorry to hear that. My question is, ' you'll never make a b. classic that will be compatible with Verizon's network.  If so, when will it be available?

  Please notify earlier.

  Thank you.

  R. Ravelo

  Hi @sandybaby57! Welcome to the community of BlackBerry Support Forums!

  Please see this article and bookmark if you want: UPDATE: where to buy classic BlackBerry: price and availability

  See you soon!

• Make the disabled according to the layer type setting.

  Is it possible to make a person in charge of the disabled setting on the type of layer, to which it is applied?  For example, if I apply the plug-in to a TextLayer can I disable some params, but allow them if I apply the same plug-in to a layer of the Image?

  In the software development kit, I have read, this PF_PUI_DISABLED "disables (grays on) the setting, usually in response to PF_Cmd_USER_CHANGED_PARAM ' but how I would disable the parameter immediately by checking the type of layer.  I was thinking of using javacript to detect the type of layer, but it is perhaps too general.  Is it possible to:

  1 programatically triggering the PF_Cmd_USER_CHANGED_PARAM

  2 detect the layer type with the software development kit instead of using the call a javascript since the plugin code?

  Thank you for your time and help!

  Best,
  Arie

  first of all, I want to dedicate this song to all of you who came back:

  http://www.YouTube.com/watch?v=ZBR2G-iI3-I

  or, better yet, my favorite blanket:

  http://www.YouTube.com/watch?v=10C68Gzd5GM

  in any case:

  AEGP_LayerH layerH;

  ERR (suites. PFInterfaceSuite1()-> AEGP_GetEffectLayer (in_data-> effect_ref & layerH)); get the reference to the layer

  AEGP_ObjectType layerType = NULL;

  ERR (suites. LayerSuite5()-> AEGP_GetLayerObjectType (layerH & layerType));

  That's all.

  the layer type is one of:

  Enum {}

  AEGP_ObjectType_NONE = - 1,

  AEGP_ObjectType_AV, / * includes all types of layer of pre - AE 5.0 (audio or video, including adjustment layers) * /.

  AEGP_ObjectType_LIGHT,

  AEGP_ObjectType_CAMERA,

  AEGP_ObjectType_TEXT,

  AEGP_ObjectType_VECTOR,

  AEGP_ObjectType_NUM_TYPES

  };

  typedef A_long AEGP_ObjectType;

  TADA!

  :-)

• turn off the ringer only on hp 640 fax

  How can I disable only the ringer and not all the sounds on the HP 640 FAX?

  Hi rmkram,

  I understand that you do not want to disable only the ringer on the fax. I'll try my best to help you with this.

  In the series HP 640 Fax User Guide on page 22, he explains how to adjust the volume.

  Adjust the volume
  You can set the volume level for the ringing and the speaker.
  Ring volume
  .. When the fax is in ready mode to adjust the volume of the ringer, press on...
  Whenever you press the button, it will increase or decrease the volume.
  NOTE: The volume of 0 indicates that the machine does not ring when a call is received.

  I hope that this information help, please let me know how it goes.

  Thank you

• disconnecting from the ad hoc wireless network

  I have problems with the ad-hoc wireless network connection. Internet connection is not necessary, I want to just connect two laptops vista to play Civilization4. We had two laptops connected properly for a few days and enjoyed the game. But now the connection does not appear to work properly.

  Two portable computers connect to each other and then after a short perion one of them disconnects with a message saying "in waiting for other users to connect."

  It's the same no matter what either portable sets up the connection.

  We tried to establish new connections of two laptops and welcomed the connections between each of them also, the problem is the same.

  We have tried to disable the firewall without success

  There are other parameters that we should look at?

  Hi Bm_mad,

  This problem may occur if the enable IEEE 802. 1 X authentication for this network check box is selected. If this box is checked, but there is no server to authenticate the connection is interrupted. If you turn on the wireless network connection, it disconnects again after a short period.

  To resolve this issue, use one or more of the following methods in the order in which they are provided. After you complete each method, verify that the problem is resolved. If a method does not resolve the problem, continue to the next method.

  Method 1: Disable IEEE 802 authentication. 1 X

  To disable authentication IEEE 802. 1 X, follow these steps:

  1. Click Start, click run, type ncpa.cpland click OK.
  2. Right click on your wireless network connection and then click Properties.
  3. Click the wireless networks tab.
  4. Under preferred networks, click your wireless network, and then click Properties.
  5. Click the authentication tab, click to clear the enable IEEE 802. 1 X authentication for this network check box, and then click OK twice.

  Method 2: Remove and re-create the wireless network connection

  To remove and re-create the wireless network connection, follow these steps:

  1. Click Start, click run, type ncpa.cpland click OK.
  2. Right click on your wireless network connection and then click Properties.
  3. Click the wireless networks tab.
  4. Under preferred networks, click your wireless network, and then click Remove.
  5. Click view wireless networks.
  6. Under management of the network, click Refresh network list.
  7. Under choose a wireless network, click the wireless network to which you want to connect, and then click connect.

  Method 3: Solve the USB wireless network adapters

  If you have an adapter (USB) wireless universal serial bus, you may experience problems that are related to the limitations of USB. If you have several USB devices, the USB network adapter can share, bandwidth, power or both to a level that it causes, you experience the symptoms described in the Symptoms"" section. To resolve this issue, try the following suggestions:

  • If the computer has more than one USB bus, connect the wireless network adapter to its own USB bus. Connect other USB devices to a different USB port. As a general rule, two USB ports share one USB bus.
  • Disconnect all USB devices that are unused or not.
  • Use a powered USB hub to connect the adapter to your computer.

  Previous post: the result.

  Bindu S - Microsoft Support

  [If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message.] [Marking a post as answer, or relatively useful, you help others find the answer more quickly.]

• Suggestion for setting up a good secured router including wireless routers

  I've owned three routers LinkSys Wireless since May 2007: two WRT54G (V6 and V8) and my current V1 E3000.  All provided configuration options that can do if it is very difficult, if not impossible, for unauthorized access to my WiFi routers.

  All changes must then your system is connected to one of the router's Ethernet ports and not through WiFi due to the modification point #3 of "General Suggestions.

  All the elements in square brackets by "<>" are the titles of LinkSys Admin web pages or sections of web pages.  Don't forget to click "Save Settings" on a single web page before you go to another web page or your changes will be lost.

  Please note that not all pages of the LinkSys Router Web Admin can use the titles of Section-page/website such as used in this suggestion.

  Make sure you know MAC address and physics of your wireless adapter so that it will be necessary for the point #3 «Proposals WiFi»  Assuming that you have a Microsoft Windows-based system, use a 'Command Prompt' to issue command ' ipconfig/all' to determine the MAC address (aka physical) of your adapter WiFi wireless connected to a router.

  After all the suggested changes, repeat the process to ensure that the changes have been saved.

  GENERALS.

  (1) < administration/mgmt=""> change the Admin password to one of your choice.

  (2) access to disable HTTP and HTTPS allow access.  After that it changed was recorded, you must reconnect to the router via note https://192.168.1.1 URL using httpS or http (without S) for a secure connection to the router admin web pages.

  (3) in Wireless disable access to the Admin web pages.  Must use the Ethernet port on the router.

  (4) in disable remote management AND disable UPnP - UPnP (a well-known Protocol should can route diversion if enabled).

  Specific suggestions of WiFi.

  (1) in turn off the SSID broadcast.  This will prevent the intruders 'driveby' to see the SSID of LinkSys Router.  Make sure that change you the default SSID of your choice.

  (2) in set your security level to the WPA or WPA2 (preferred WPA2).  Do NOT use WEP because it's encryption algorithm can be cracked in less than 5 seconds.  This will protect your transmissions between your system and the router.  The E series routers are supported both WPA/WPA2 depending on the client configuration.  My WRT54G routers would support only WPA or WPA2.

  (3.) in Select AES, TKIP not as security consultants have recently discovered a flaw in TKIP encryption crackable.

  4.) Select a passphrase that you and systems all allowed must be used to secure your router connections.

  (5) in the enable filtering MAC and "Allow only PC" whose MAC addresses are defined in the .  Both of these changes will require that you register addresses MAC and physical of all wireless clients that allow you to connect to your network router.  Failure to record the physical address/MAC system will refuse this system to access your network, even if they have the correct passphrase AES and SSID.

  1. disable the SSID broadcast is useless. Any Drivede will detect always immediately the access point because it should send signals of tag.

  It is trivial to force a wireless client to reveal the SSID. Thus, any hacker will be able to learn the SSID almost immediately after it has detected the presence of your router.

  In addition, to disable the SSID broadcast causes known problems of connection/reconnection with several wireless devices.

  In addition, broadcast disable SSID drains the batteries in your wireless devices as they have to actively seek a connection to your SSID to know whether here or now.

  As long as your wireless device is not connected to a wireless network, it will be continues to try to connect to your SSID at regular intervals. For example, if you have your iPhone set up to connect to your home network and you pull out your iPhone permanently tries to connect to your SSID, transmitting the requests of the association on a regular basis, actually bloating on your "hidden SSID' to anyone.

  As transmitting something takes a lot more power then passively scanning and tuned radio waves, it drains the battery. If you need good battery life with your ever wireless devices connect them to a network with SSID broadcast disabled, or make sure that the device does not automatically connect to it!

  Never disable the SSID broadcast, especially not for security reasons, because they do not offer any added safety or an advantage.

  2. the MAC address filtering does nothing more. MAC addresses are always in the unencrypted part of wireless packet. Any attacker will immediately learn the MAC addresses of your wireless devices. It is absolutely useless in the means of security and cause problems as the best for you. Do not bother about the filtering of MAC addresses. It does not prevent attacks on your network as it is easily circumvented.

  Use WPA2 with AES and a password strong. That's all that is necessary to protect your wireless network.

  The rest is a joke for any aggressor and bothers you much more than the alleged assailant. If an attacker was able to decipher your network WPA2/AES the SSID of your network and MAC addresses are a free byproduct you will get during the cracking process...

• cannot change the name of the net p1102w wireless

  I have a P1102W printer.  It was installed and worked fine for a long time.  I had other requiring changes that change the name of the wireless network. Even after running the Wireless Setup again the printer retains the old name of network and I can't seem to do the procedures proposed for displaying and editing this work.  When I try to access the web site to the IP address that is given it says that the page is not accessible. How can I change the name of the network the printer to the correct network wireless?

  I am running Windows 8 on the laptop that I use to set up the printer.

  Product # CE657A

  Hello

  Try resetting the network settings by disabling the printer.

  Press and hold the Cancel and wireless, then turn on the printer and keep both buttons until the lights between the buttons will be Flash.

  Then run the install software once more by selecting the wireless connection, you may be prompted to temporarily connect a USB stick to transfer the current settings of the network to the printer.

  Please let me know of any changes,

  Shlomi

• Automatically use the wired on wireless LAN connection when using the docking station

  Hey guys!

  I use the my T500 with the Advanced Mini Dock @TheDude recommended in this thread: http://forums.lenovo.com/t5/T400-T500-and-newer-T-series/T500-Recommended-Compatible-Docking-Station...

  I had almost a month now, and whenever I anchor my laptop I have to pass the connection wireless switch off hard or using FN + F5 and extinguish this particular radio.

  Is it possible to have the computer automatically choose the wired connection when it is available, otherwise use the wireless radio?

  I use Windows 7 Prof 64 bit.

  Thank you

  c1p0

  ThinkVantage Access Connections (AC) can be configured to do this. Change your location profile and change the order of the adapter associated with this place, for example, order first as Wired and Wireless second.

  When I am connected Wired and I pull the Ethernet cable, AC will switch to using wireless automatically. When I put the Ethernet back in, it starts automatically by using the wired and wireless don't report limited or no connectivity (which means that the switch has occurred). You will have to perhaps set up wireless in AC power options, i.e. disable radio when not in use (I did not sentence again).

  This could be similar to a docking station solution. Mine is without docking station; When I'm at the office and go to a meeting, I pull the wire and have continuity.

  Ideally, the CA should provide a solution. But it may take some fiddling.