settings on the router for ITouch

Similar Questions

• How to access my settings of the webcam for an hp pavilion windows vista any help would be appreciated

  How to access my settings of the webcam for an hp pavilion windows vista any help would be appreciated

  See if a program was installed for him. Or use something like Skype / instant messaging program

• Please help to configure the router for internet connection 871W!

  Hello world!

  I just started styding for CCNA, so I'm totally new to Cisco stuff. Recently bought a router 871W and spent two days in a row trying to configure internet connection with no luck! I use the port console for the configs and SDM/CCP. Would be greateful if someone could tell me how to do simple configs of internet connection. I googled everything but it's still confusing. I can't assing all-IP ports FA 0-3. I used instead of the VLAN. But all tutorials use FA0 and when I try to assign an IP address to FA0 it gives me some L2 cannot be assigned or something... :/ And I am also confused at what address IP use for WAN.

  I connected the cable between the Modem and the LAN of the PC port and copied some IP addresses which I think I have to use to configure the router for internet connection. And here they are:

  ISP IP: 76.114.54.255

  SUBNET: 255.255.248.0

  GATEWAY: 76.114.48.1

  DHCP: 69.252.97.4

  DNS: 75.75.75.75

  75.75.76.76

  If you can, please help! Thank you!

  Hi david,

  Looks like your 871w can not get a dynamic IP address: % unknown DHCP problem... No possible allocation

  you could ask your ISP to perform a reset/clear MAC add and try again?

  also, kindly post lastest "show run".

  Edit: just to see you've updated your screenshot. could you add command under 4

  Mac-add 0001.4af9.8b83

• R7000 as router with the router for mobile broadband Internet

  Hey guys. First of all, my apologies for my somewhat inadequate English skills. Secondly, I am brand new to the community, so apologies in advance for any fault :-) Third stop, apologize for having a complete beginner :-D

  So, for the issue: I recently bought a router top mobile broadband 4G (4 G MBR) to my apartment, because of the gap of strength and speed signal very low quality of the cable to the ground on my Street (fiber is to come next year).

  But the router provided by my operator isn't on par with my router R7000 Nighthawk when he comes to reach wifi, wifi speed, number of outputs of LAN and power of the processor.

  So, I want to use my R7000 my router, the internet signal from the air to the 4G MBR, then by cable to the WAN of the R7000.
  In other words; I want to just 4G MBR to simply pass / transfer the internet signal to my nighthawk R7000 router so I can use the R7000 as my router, LAN and wifi.

  How can I set this up?

  Thanks for your help!

  Update: the MBR has been no help at all. As far as I could tell, there is no possibility to bridge or pass-through mode. The R7000, as she does the work. I just put it in AP mode, adjust all the wired connections DHCP/auto IP assign and everything works great.

• Unable to connect to Homegroup Windows 7 between the Modem to the PC and the Modem to the router for PC users.

  I want to talk about WIRED computers, do not speak of wireless.

  I have 3 PC:

  -2 are connected via Modem directly to the PC.

  -1 is connected through router, and the router is connected to the modem.

  The problem, this is it, it cannot detect the homegroup that I created on the computer that is directly connected by modem.

  The 2 PC via modem are perfectly detected and connected to the homegroup, so I want to know what I would do to another PC (which is connected to the router via modem) detects the homegroup, I had already created?

  Help, please.

  A Modem can have only two ports, connect to the internet (Wide Area Network) and the second to a SINGLE local device. In most cases the internet Service Pwill provide with only an IP address so itself cannot connect to more than one at a time. In current solutions, it is very rare for a Modem to use. If as you say, you have several devices connected to this unit then he himself is a router but possibly with the Modem built in if you have ADSL ISP.

  If your second unit is also a router then that explains why you cannot connect all devices in the same residential group.

  Router 1 has created a Local Area Network including both PC and the WAN port on the Router 2. Router 2 has created another independent local network with the 3rd PC. It is very likely that the two local networks will be IPv4 and traffic can be routed between them correctly in both directions according to the two local networks subnet ranges.

  Even if they are properly configured to allow traffic that HomeGroup requires IPv6 that some home routers support fully and every Member of the residential group must be on the same LAN anyway, he will not support a routed connection.

  Remove the 3rd PC of the 2nd router and plug it into the direct 1 router, remove the router 2nd the 1st in order to free the port. 3 all PCs are now on the same local network and communicate both IPv4 and IPv6, and homegroup should work.

  If you need additional ports provided by the 2nd router for other devices is not part of this problem then consider replacing it with a switch. If you use Router 2 for other devices Wi - Fi irrelevant then you need a wireless access Point.

• Settings of the AFN for a direct TCP (3G v.s. GPRS) connection

  Today, I read a lot of articles about the transportation options for the Blackberry network.

  I installed the Tool of Network Diagnostics on my device (BlackBerry 9300 v5.0).

  I'm Tournai on "Mobile network" and disabled the "WiFi". Therefore, my device must use the direct TCP (HTTP protocol) only.

  According to this article, for a cell TCP connection, we need to set up the APN settings, otherwise we will have 'Tunnel failed' error

  http://docs.BlackBerry.com/en/developers/deliverables/21128/Network_transport_options_1293321_11.jsp

  However, without specifying the AFN, I was still able to have labour Direct TCP (HTTP).

  I'm in New Zealand, I tested the Network Diagnostic tool with 2 dgree and vodafone sim cards. Two of them work properly. Two of them are 3 G networks

  However, a lot of people on the internet saying that if they do not specify the APN for GPRS or EDGE networks, they would get the error "failure of Tunnel.

  So, I had the impression that with 3G networks, don't need us to specify the APN.

  I don't know if that's okay?

  One of the really annoying things on the treatment on the Blackberry network is its inconsistency.  I think you've hit one of them.  I saw this in the past with Vodafone, I wasn't sure that this has happened with other networks but maybe so.

  The inconsistency is the following.

  If your connection URL looks like

  http://...; deviceside = true

  If you think that this will force the connection to use the carrier TCP aka Direct TCP.  However, on some phones of brands, including Vodafone, is not correct.  On these phones a connection as it goes actually on WAP.

  To force the direct TCP, you must follow the instructions in this post:

  http://supportforums.BlackBerry.com/T5/Java-development/Vodafone-UK-direct-TCP/m-p/463081#M92387

• How can I change the settings of the clock for Trinidad and Tobago

  My computer clock has changed, but I can't seem to stay on the exact time of Trinidad and Tobago and does not change to or from daylight saving time. The climate is tropical and our time never changes, but the computer changes, so I want to stop time to change.

  Uncheck you automatically adjust the clock for daylight saving time in the time zone settings?

• How is the ACL name of the router for fleeing?

  I want to test running and have a question, the name of the ACL.

  I configured the device blocking on the IDM,

  -blocking interface Fastethernet0/0 =

  -direction = in

  -Pre IDS_PRE = ACL name

  -Ask the IDS_POST = ACL name

  Change a signature "ICMP-echo" to shunhost and update on the router but added new ACL under Fastethernet0/0 as the name IDS_Fastethernet0/0_in_0 and rocking it with IDS_Fastethernet0/0_in_1.

  Q. why the ACL name not follow my name on the IDM?

  Thanks in advance.

  I think that there is some confusion about what are PreACl and PostACL.

  The PreACL and PostACl entries in IDM do not affect what's name created sensor ACL on the router.

  The sensor will always create an ACL that is named with the following format:

  IDS___<0or1>

  So for you the configuration it would create the following names of ACL:

  IDS_Fastethernet0/0_in_0 and IDS_Fastethernet0/0_in_1

  E he uses 2 ACL because it cannot modify an ACL that is currently applied on the interface. So if ACL 0 is currently applied then it will create 1 ACL and then apply ACLs one (which Désimpute ACL 0).

  The sensor can then remove 0 and create a new ACL 0 when a change has to happen.

  So, what are the pre and Post ACL names used for?

  One of the biggest complaints we had with older versions of the probe was that the user could add no lines to the ACL that created the sensor.

  So we came to the top with the pre and Post ACL so that users can add entries to the ACL that creates the sensor.

  The user must connect on the router itself and create an ACL with little matter the name they want. Inside of the ACL, they put the entries they finally want to see at the top of the ACL that will create the sensor.

  When they set up the sensor, they take the name of the ACL, they created and enter it in the field for the name of PreACL.

  The user can do the same for the entries they want at the bottom of the ACL generated by the sensor by creating another ACL on the router. Put it in the Scriptures they want to see at the bottom of the created sensor ACL and then type the name in the name of PostACL field.

  If the names of pre and Post ACL aren't going to use to name the ACL created sensor.

  But on the contrary these ACL is read out of the router by the sensor, and these ACL entries will be placed inside the ACL, created by the sensor.

• OSB - How select variable used in the routing for buss request message. serv.

  I have "modeling of a stream of messages to a proxy service.
  According to the content of the incoming request message, a (conditional) branch is selected. The message must be routed to a business service in this branch.
  This service of the company has a different message definition requires that the proxy service. A kind of transformation is probably necessary. (not yet implemented)
  Question is how to choose what variable structure (I created a variable of Interface Service for business) that will be used during the call to the sales department.
  Only thing that I can choose, the service and operation.
  
  How to continue?

  The payload for the service of the company must be in the * variable $body. There are also other variables pre-defined as $header and $attachments that could make sense if your need to send SOAP headers or accessories for business service.

• How to remove all settings from the router to the computer?

  I plugged my router on laptop since my computer was not working. After a computer repair I tell router to the computer again, but then I could not connect my laptop (which has been connected to the router before) to my wireless network. When I try to connect I have always the same message that says "Windows cannot connect to the selected network. The network can be is no longer in range. Please refresh the list of available networks and try to connect again. ".

  Hi IgoKele97,

  Adding to the valuable advice, you can also have a look at the following article.

  Windows wireless and wired network connection problems

  I hope this helps.

• How can I reset the default settings of the monitor for Vista

  Somehow, I ended up setting my screen laptop like I have look on the side for one of the two users on the PC.  The other user is fine.  Any ideas on how I can reset the default to display monitor?

  Try holding CTRL + ALT + UP arrow at the same time. You can also try the other arrows. I hope I could help

• How to change the existing settings of the source for the container system

  Hello
  
  Cannot change settings in the system container (Oracle 11.5.10) source source.
  
  Please guide me how to change the settings.
  
  Thank you and best regards,
  Partha.

  Partha, you should not change the current container. Create a new container by copying the existing container and make any changes required in the present.

• HP4645: HP 4645 - change the router for Humax and now always invalid password

  Hello HP / person

  Please help me, I change my ADSL internet fiber and provider gave me a router Humax. However, when I tried coonect Assistant wireless via HP4645, it always show me "invalid password" this wireless I use 5 to 6 devices so I'm very sure that the password is correct.

  I tried putting the Cd and it ran however it n SSID inavailable

  Please help me before I change the internet from ADSL to internet fiber with new router it works just perfect.

  Hi @c13pan,

  Welcome to the Forums of HP Support!

  I see that you are unable to get your HP Deskjet Ink Advantage 4645 e-all-in-one printer connected to the new router. I'd be happy to help you and don't forget to come back to this thread and check "Accept as Solution", if I have successfully helped solve you the problem. If you want to say 'Thank you' to my effort to help, click on the "thumbs up" to give me a Kudos.

  I understand that this can be frustrating, we should be able to get this to work for you. Looks like the printer must hang on the old settings or trying to connect to the wrong network.

  To correct this problem, try the following steps:

  Restore the default settings network settings.

  1. press on the wireless button to access the menu of the status of wireless.

  2. press the button next to settings to access the settings menu wireless.

  3. select restore default settings.

  4 confirm the selection to restore the default values.

  Source

  • Before you reconfigure the wireless, make sure that the SSID is not hidden.
  • If you have a dual band router, rename the network 5.0 GHz and the name of the network is unique.
  • Make sure your computer is on the 2.4 GHz network when you try to reconfigure the wireless.

  To confirm you are on the same network and the password is correct, please use the printing and scanning doctor.

  HP provides a free tool called HP Print and Scan doctor to diagnose and troubleshoot printing and scanning. Download and run printing HP and doctor Scan quickly and automatically multitask resolution of known issues for this problem. When you click this link, HP Print and Scan Doctor is downloaded using the download of your Internet browser capabilities.

• Dell order | Configure not applying is not the settings of the BIOS for Inspiron 13 7000 series

  I tried to define a system and/or a password via the command line and a package .exe or CCTK file via the export of GUI and none of these work for me.

  The following text appears in the log:

  Option: setuppwd

  2014/11/12-11:02:14 cctk - error in the definition of value.
  Note: In some machines, Hdd if password or system password is set, you cannot set the password.

  2014/11/12-11:02:14 cctk-
  Option: syspwd

  2014/11/12-11:02:14 cctk - error in the definition of value.

  I tried this on a Windows 8.1 system and for S & G, on a Windows 10 system with the same result.  I even tried to create the 2.2 CCTK config and have the same result.

  What is the cause?

  Hi CAPP3R,

  DCC (CCTK) deals with the BIOS settings only for Dell commercial client systems. CDC is not yet supported on all Inspiron models.

  Kind regards
  Karthik.C

• Project settings of the AVCHD for a better quality of DVD

  I used Pinnacle Studio Ultimate for the past five years with a lot of effects, transitions and rich text content.  I bought a Sony HXR-MC50U and recorded media are set at its highest potetial: AVCHD video format.

  Pinnacle has done OK with my same old technical until 45 min length has been reached. I then had a lot of breakdowns of the system.  I know that I can transcode to the good old AVI, but I want to preserve the quality of the video at its highest level.

  It is my first DVD of first Pro/Encore project.  Although I am new to the software, plugins Pinnacle are very similar and some are the exact same as hollywood fx plug-ins.  I realized the party edition as a piece of cake.  I'm stuck at the part of the project in again, so I'm here asking for HELP!

  System:

  Windows 7 x 64 professional

  Adobe CS4 Master Collection

  ASUS P8P67 motherboard

  Intel i5 2500 K 3.3 GHz O.C to 4.3 GHz

  16 GB of Ram GSkill DDR3 @2133

  nVidia Quadro CX with 1.5 GB of Ram

  WD Raptor 10 k RPM hard drive.

  850W PSU

  Current project and procedure parameters, I followed:

  1 - the project to create a new PR NTSC DVD HD

  2 - create new sequence: 1080i30 (60i) 1:1

  == > My AVCHD info: (24 Mbps) 1920 x 1080/60i 29.9 fps

  3 - Importeded video of the internal hard drive and adding clips to a timeline...

  4. - applied Adorage plugin Transitions, double cropped video screen next to a few points, etc...

  5 - created new sequence this time for securities and other display information

  6 - imported clips AVI 720 x 480 resized to the size of the image and created securities within the PR

  7 - new sequence to combine a total of 6 sequences with little video effects and about 1 hr 40 min length then added an audio track that overlap two or three short clips

  8 - all projects registered and selected Dynamic Link: sent to the settings still Blu - Ray 1920 x 1080/60i

  Once I got, I got a lot of 'fun' create a menu driven with 15chapters

  1 - created new timeline, timeline sequence added

  2 - created a new Menu and submenu and then published their text in Ps, rescued and return to en

  3 - Motion video added button in the submenu... double button, total 5 buttons

  4 - menu linked to all its sections corresponding, Next, Previous, hand Menu etc... In addition, background Audio croped on a length of the default value for the menu background video.

  5 - check project... Checked them all very well... Previewed and works nice

  6 - build the DVD Image, gave the image a name, selected directory and 'click '...

  After several tries, I managed the menus to render correctly and no mistakes over this point.  If until then "transcoding failed.

  I can make and PR, but the quality is considerably lowered.  The main reason I go to Pr is output as many on the final DVD-quality video possible.  I always create image to DVD using Pinnacle, first to save the blank media.  Then test the image and if it's OK I then burn with confidence.

  I've updated to the latest versions available all my programs. Pr I ran as administrator to ignore my stuff from the operating system security.

  It's been a long week and I hope that someone expert in Premiere Pro helps me understand this error.  I cannot transcode now, or build the project.  I get the same error: failure of transcode

  I noticed a red line on the timeline on parts of my project in Premier Pro when adding double video (50 50 screens), transitions, or other video effects.

  One last note, I save all my projects and final DVD Image to a server FTP of D-Link with drives mapped to my computer.  It is linked to a 10/100/1000Mps connection on my local network.  Pinnacle does not even notice that it is internal or network.  My read/write speed is the same or faster than hard drives internal: 40-60Mps... Change the folders on hard drive made no difference.

  First with a built-in mpeg2 dvd export.

  Import into Encore.

  Menu and export the image.

  See if this will help.