Several channels with the launch of unique digital dashboard

Similar Questions

• Write to digitall all ports (channels) with the decimal value

  Hello

  It is possible to write all digital channels with a value decimal for a device with 96 channels at the same time?

  I have a USB-6509 camera and I want to write each value of Pentecost bit 1 in the loop (for the first transfer I write 0,1,2,4,8,16, 32, 64 and 128) with the line "Dev3/port0 / line0:7", but if I want to write all ports at the same time, how to set the line and the "write.vi DAQmx?

  Thank you.

  You can configure the reading and writing in the ports of 8 bits with the 6509.  For example, you could write just 128 to "Dev3/port0.  If you want to write to all 12 ports, I recommend doing a task that is several channels on the 6509 module, each channel of the task being a port.  You can then use the channel Multiple, single sample of writing of your values.  Your values must be in a table of U8.

• Impossible to read 4 channels with the or 9234

  Hey, I'm tasting 4 simultaneous channels to 51.2 kech / s rate for each channel with the NI 9234 module.
  I use a callback function to read from the buffer.
  I am accept to get to playback 4 channels of 51.2 k * 4 = 204.8 k s/s.
  and I still recive data 51.2 kech / s.

  Need help, I don't know what's wrong with my code.

  I enclose my hope of code it will help...

  Thank you!

  My installation information:
  Material: NEITHER 9234
  Version of Windows: XP
  Language: Qt (C++)

  Hey simon27,

  When you have installed DAQmx, did you also install text code support? There are several examples that should have installed with DAQmx which is very helpful in getting you started. "" "" "They can be found by going to your Start menu, then all programs" National Instruments "NOR-DAQ" NOR-DAQ "support textual Code ' ANSI C examples.

  In case you do not installed the supported text based code, I have attached two examples which I think would be more useful to you. Try to run these examples and see if you get the same errors.

  -Nathan H

• Windows media center analysis drops channels with the call sign not in the guide

  I'm trying to find the right place to report this problem.

  When library scanned for channels recently that he hasn't found a bunch of DTT hd (clearqam) who are present and unencrypted.

  Scanning with the help of the application of the tv tuner has revealed that the channel was present and unencrypted.

  He showed that the channels have call signs which were not present in the digital guide. that is a call sign was "KPHO HD" when the digital guide for the channel list KPHODT

  I had checked in the list of all channels that find the Media Center and the numbers were not present in media center.

  This seems to be a bug because the channel should be found even if no digital guide for the channel is found.

  The solution is to locate the actual channels by another application.

  Add channels with the guides Add missing channels

  Change the channel to have the correct list and the channel number.

  Check out these links

  TV on your computer: understanding and TV tuners TV signals:
  http://windowshelp.Microsoft.com/Windows/en-us/help/aa79e7b4-E423-4459-ad22-1c240a8ffcd51033.mspx

  TV signals that are supported by Windows Media Center:
  http://windowshelp.Microsoft.com/Windows/en-us/help/ef5b8360-958c-425B-9529-2922167e78631033.mspx

  The transition to digital TV and Windows:
  http://windowshelp.Microsoft.com/Windows/en-us/help/4d88063d-8842-42d2-B699-0fdce8249e531033.mspx

  Set up a TV signal in Windows Media Center:
  http://windowshelp.Microsoft.com/Windows/en-us/help/589879da-b5a9-4E8F-b43c-c5eb99290e8d1033.mspx

• Return of the mistake of MUSE: why do we not have several files with the same name?

  Well - I thought I had all this worked and fixed, but I met the download error 'Why do we have several files with the same name' once again.  (I downloaded all the files several times today in order to 1) works the way it worked the last time and 2) get an OAM file that is not loading for some reason any load again and the download takes about an hour to transfer all the files manually.

  To recap:

  (1) an option "Upload only modified files" returns the 'Muse has encountered an error and closes.  Why do we have several files with the same name? "error just as before.

  (2) a full download will work but takes forever and is NOT a substitution for work changed files option.

  Please advise with possible solutions!

  -Dave

  Is it possible to have two .oam different files in different folders on your computer where the .oam files have the same name? I'm theorizing that there may be a bug in the treatment to ensure the folder created for a .oam placed on the server receives a unique name, particularly in the case of a partial update of the site on the server.

  Please send us the .muse file and all the files in .oam related to [email protected] along with a link to this topic for the context so we can attempt to reproduce this error and isolate the root cause. If files are larger than 20 MB, you'll need to use a service such as Adobe send & Track, Dropbox, creative cloud, WeTransfer, etc. file sharing. Thank you.

• Several members with the same alias

  I have several members with the same alias name. Is there anyway to build the dimension with the same alias name members?

  In general, I'm going to concatinate the member name (as a prefix or a suffix) to Alias to make it unique

• Can I have several structures with the same case of event event?

  Hello

  I do an application which reproduces the front of the power supply HP6675A. To do this, I did a machine to States with different States

  (initialize, measures, voltage, current, ocp, ov, store, recall, etc.). In each State, should have a structure of the event that attracts the events of the buttons, as for example: If the current state is the voltage mode and the current button is pressed the next State will be the current mode. For this purpose in each State of the state machine should be the same structure of event with the same events.

  My problem is that the Vi does not work properly when I have several structures with the same case of event event. There are some possibly to do and how? Or is impossible to have several events? I read a few posts, but I can't find solutions.

  Any help is appreciated.

  Thank you very much.

  In general, you should have 1 structure of the event in your VI.  In your state machine, the structure of the event should be in "pending" status  So you will probably start in the State of the initialization and then spend idling.  Then, the user presses the present button.  If your state machine should then, go to the current state and then return to Idle.

• Need help with the launching track pack for forza code 4

  Bought new Forza 4 and the lancer Track Pack code does not work, how do I get a code that is generated in the form I've already paid for it. Rank of loads of numbers and sent 10 s of emails but cant seem to get help.
  
  This is the help I get when the cat to an Ambassador xbox on xbox.com
  
  Terry wrote:
  Need help with the launching track pack for forza code 4
  The Xbox Ambassador says:
  Location of Ambassador of the community...
  The Xbox Ambassador says:
  Location of Ambassador of the community...
  The Xbox Ambassador says:
  Your question will be answered by an Ambassador of the Xbox. You have been connected to the Ambassador as a user Xbox [3]
  The Xbox Ambassador says:
  Hello
  Terry wrote:
  Hello
  The Xbox Ambassador says:
  Hey
  Terry wrote:
  just to be on the phone to xbox live support and was told to come here
  The Xbox Ambassador says:
  ok\
  The Xbox Ambassador says:
  What is your problem?
  Terry wrote:
  I bought the 4 for forza ansd 360 new sealed Christmas...
  Terry wrote:
  has got 2 codes that accompanies the game but the pack track code does not work
  The Xbox Ambassador says:
  Wow good
  Terry wrote:
  whenever I put in the code it says code redeemed
  The Xbox Ambassador says:
  I think the code is used. You must return to the retailer
  Terry wrote:
  I tried to, but since I already opened the case they will not accept
  The Xbox Ambassador says:
  Oh. No,
  Terry wrote:
  the code had been used or defective as I am the only person who has touched the game once opened, tried to enter the code when it is open
  The Xbox Ambassador says:
  Maybe it was auto bought?
  Terry wrote:
  so, how do I get another code generated track Pack if defective?
  The Xbox Ambassador says:
  I do not know.
  Terry wrote:
  bought the game new, so I get the track pack
  The Xbox Ambassador says:
  Oh. It's bad.
  The Xbox Ambassador says:
  I think that if you Exchange 1 code it will buy it
  Terry wrote:
  car pack code worked, starter pack did not work
  The Xbox Ambassador says:
  Oh.
  The Xbox Ambassador says:
  It's a bad
  The Xbox Ambassador says:
  BTW you have an evolution of the tests?
  Terry wrote:
  Yes, I want to? but more anxious to get a code object generated for this pack
  The Xbox Ambassador says:
  Hey if I help can u give me this game too?
  Terry wrote:
  ?????????????????
  Terry wrote:
  So is it possible to get a code for that time?
  The Xbox Ambassador says:
  Hey
  The Xbox Ambassador says:
  Yes.
  The Xbox Ambassador says:
  you need to contact them
  The Xbox Ambassador says:
  and tell them that the code is used.
  Terry wrote:
  I was told to come here? where can I go to get the code?

  Hi Terryg76,

  ·         What version of the operating system is installed on the computer?

  I suggest you to contact the game manufacturer for more help and information.

• I've had several accidents with the blue screen noting CRQL_NOT_LESS_OR_EQUAL

  Hello.

  Here are some files dump of my crashes: http://cid-5cfec8d823e42bd3.office.live.com/browse.aspx/.Documents

  Here's what happens:

  Since June, I've had several accidents with the blue screen noting CRQL_NOT_LESS_OR_EQUAL (Yes, CRQL, no IRQL level), and they are producing at closer intervals. I also notice some changes of office and some sounds to open files that are not have happened before. I run antivirus and malware and found nothing. I did a disk cleanup and defragmentation.

  I also tried to install via Windows updates and everything seems to date. I ran Windows Memory Diagnostic tool, and it found no errors. I ran Windows Startup Repair and got the following note:

  Root Cause found.

  Unknown bug control: one error checking.

  Parameters = 0 x 0, 0x817dc32c, 0x820e8114, 0 x 0.

  After the last crash, I got a message saying that Windows is aware of the problem and trying to fix it. Any ideas?

  
  Thank you in advance for your help!

  Hello

  Uninstall Faultwire and look for the codes manually as needed. The link to troubleshooting blue screen
  page will show you how to get them.

  How old is the system? A real computer store (not the leeks and glances at a Best Buy or other large surfaces)
  Stores) can help to give a proper diagnosis of the machine.

  You can use Safe Mode - repeatedly tap F8 as you start - use to back up your data in a redundant
  way off the machine. Then re-install Windows that "might" help if the problem is software partner.
  Of course, you will need to reinstall your programs and restore the data in the machine.

  Although there are a large number of errors there could be a cause for all. Try to remove ALL power and
  reinstall all the memory cards and cables (at both ends, when possible) - actually delete and replace.
  do not just tight. Clean the dust bunnies (of course those who are for a PC - for a laptop to ensure that)
  the vents are clear). Try using a small fan blowing through the vents to see if heat is a problem.

  Update key drivers - display/video, NETWORK card and WiFi (network), sound (do not forget to check the sound card drivers
  What update because they will often rollback then repeat the installation until the correct version appears), modem
  and all of the other major features, you could have as 3rd party mouse or keyboard.

  This is my generic how updates of appropriate driver:

  This utility, it is easy see which versions are loaded:

  -Free - DriverView utility displays the list of all device drivers currently loaded on your system. For
  each driver in the list, additional useful information is displayed: load address of the driver, description,.
  version, product name, company that created the driver and more.
  http://www.NirSoft.NET/utils/DriverView.html

  For drivers, visit manufacturer of emergency system and of the manufacturer of the device that are the most common.
  Control Panel - Device Manager - Display Adapter - note the brand and complete model of your
  video card - double - tab of the driver - write version information. Now click on UPdate Driver (this
  cannot do anything as MS is far behind the certification of drivers) - then do a right click - Uninstall - REBOOT
  This will refresh the driver stack.

  Repeat this for network - card (NIC), Wifi network, sound, mouse, and keyboard if 3rd party with their
  own the software and drivers and all other main drivers that you have.

  Now go to the site of the manufacturer of system (Dell, HP, Toshiba as examples) (restoration) and then of the manufacturer of the device
  (Realtek, Intel, Nvidia, ATI, for example) and get their latest versions. (Look for the BIOS, Chipset and software)
  updates on the site of the manufacturer of the system here.)

  Download - SAVE - go to where you put them - right click - RUN AD ADMIN - REBOOT after each installation.

  Always check in the Device Manager - tab drivers version you install actually shows up. This
  because some restore drivers before the most recent is installed (particularly that audio drivers) so install a
  pilot - reboot - check that it is installed and repeat if necessary.

  Repeat to the manufacturers - BTW on device at the DO NOT RUN THEIR SCANNER - manually check by model.

  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  How to install a device driver in Vista Device Manager
  http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.html

  If you update the drivers manually, then it's a good idea to disable the facilities of driver in the Windows updates,
  This leaves ONE of Windows updates, but it will not install the drivers who are generally older and cause
  questions. If updates offers a new driver and then hide it (right click on it) and then go look for new ones
  manually if you wish.

  How to disable automatic driver Installation in Windows Vista - drivers
  http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
  http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

  NOTE: Often restore audio drivers to check the version after installing and restarting is
  see if the version you have installed is there, otherwise repeat the installation - restart until it is. This may take
  several tests according to the recommitments how much he makes.

  Hope these helps.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• Has anyone found or written a "Win 7 USB driver" for use with the Olympus C-3000Z digital camera?

  Has anyone found or written a "Win 7 USB driver" for use with the Olympus C-3000Z digital camera?

  On Fri, 28 September 2012 18:02:40 + 0000, bertcoy wrote:

  Has anyone found or written a "Win 7 USB driver" for use with the Olympus C-3000Z digital camera?

  Looking at the website of Olympus, it would appear that we do not
  There are.

  But you do not need a driver because you do not need to connect your
  camera to the computer. Just put the memory card in a card reader and
  access like this instead. I prefer to do it with my camera,
  because it is easier, faster and uses no battery in the camera.

  Ken Blake, Microsoft MVP

• Several files with the same name.

  Cannot publish to Business Catalyst because of a fatal error, where it is said "why do we have several files with the same name?  The website and all its contents have not changed in more than a year with the exception of minor changes to the wording so unable to understand what the error is encountered. Are there not better misdiagnosed at one point less for the files in question.

  The problem is the result of a mixture of case-sensitive and case-insensitive between how files within the .oam are put into interaction with and what is written in the muse_manifest.xml file during a re - download full compared to an incremental download.

  If all .oam packages files are tiny and the original .oam were replaced in Muse with the all new tiny .oams, then you should select Upload: publish all the files in the dialog box Options. From there, forward publication of incremental changes should work without errors.

• I've uninstalled and reinstalled the drive several times with the same result, my problem is when I download the drive icons for my browsers and above all my desktop icons change adobe logo, so when I click on them Adobe tries to open them.

  I've uninstalled and reinstalled the drive several times with the same result, my problem is when I download the drive icons for my browsers and changing most of my the desktop icons for the adobe logo, so when I click on them Adobe tries to open them, of course, he does not format because it's not an adobe application , so I tried to restore the computer to an earlier date and it wont let me as long as Adobe reader is installed, so I need to uninstall and now I have nothing to open files and downloads of Adobe, someone had this problem and if so, did you get it resolved? Thank you Tommy...

  This may help: Application, file icons change in Acrobat/Reader icon

• How to be sure that the PDF opens with the launch of JavaScript

  How to be sure that the PDF is open with the launch of JavaScript. For example, I can open PDF in Acrobat is not Reader, but in Foxit Reader without supporting JavaScript

  
  

  After you have determined that you are in a PDF viewer compatible JavaScript, you can also check that the objects and methods that you plan to use are also present from Adobe viewers on mobile now run some JavaScript.

  See the details here JavaScript for QAnywhere Player Mobile (iOS)

  J-

• XOQ-01950: Cube contains several BuildSpecifications with the same name.

  Hi all
  
  When executing the option to maintain Cube he throws under question: any clue?
  
  XOQ-01950: the AWCubeOrganization for cube 'NN_OLAP_POC. MARKET_SALES_CUBE"contains several BuildSpecifications with the same name.
  
  Thank you
  Exq

  This error should show only upward when you create a cube (by importing XML), not when you maintain. So, I'll assume that's what you hear.

  If you are importing XML that references an OLAP object that already exists, whereas the new definition replaces the old. The only exception to this rule is the BuildSpecification object. This kind of object is called, but it does not follow these conventions (for reasons of disorder of implementation). If you import the XML code that has a BuildSpecificaiton with the same name as one that already exists, then you will trigger the error you see. Here is a relevant example of XML.

  The solution is to remove this section from the XML before importing it.

• Use several channels in the order of RT

  Following this post, and based on a simple sequence of RT that monitors a single channel, now I want to control multiple channels with setting specific time and level. The logic of this was to pass an array of strings that you want to monitor in the .vi create sequence parameter assignment (channel) and use arrays to manage all the time and level settings.

  

  However it seems that the sequence of RT cannot manage this type of object... so, how do I extend this functionality to several channels... Maybe that's the wrong avenue to use rt sequences?

  L.

  ... well, I look at one of the approaches is to create several calls sequence on a given sequence, each with different settings, then start them all in parallel. It seems to work for the moment.

  A simple question as opposed to events is used (for now) to detect when each called sequence stops and returns its result.

  Laurent