sevice manual

Similar Questions

• Add SSD to question dv7t-7300 HP Envy.

  I ordered a custom of dv7t-7300 HP Envy. I want to add an SSD, something along the lines of an SSD of 7.5 mm. I just need to know a few things.
  
  (1) given that the computer just that with a HARD drive (depending on configuration), is the second drive Bay hard to a 'HARD drive enclosure? And if so, should be 7.5 mm 2.5-inch SSD, or it must be a 9.5 mm SSD?
  
  (2) if the caddy is not included, where can I get one? And should it be a basket, or is it implemented different now?
  
  Any other information you can provide would be great! Thank you.

  Nothing like that self-help. Return it. On the back of it is a large "T" plate shaped. Remove the screws, pull it out and look inside. You have two hard drive bays. Are all dv7s to dual hard drives, but the method to connect readers varies a little.

  Manual

  See instructions starting on Page 49 of the above link Sevice manual.

  An SSD will work in each Bay. I would use the SSD as drive for the operating system to take advantage of the speed of the thing, which is really amazing to see the first time you see it. There is also a place for a WSSD, but there is no need of a GSU if you use an SSD as your primary drive. Still if you want uberstorage you could spend a ton and purchase a 256 GB WSSD and have actually three usable discs.

• I have a HP G62-52SE model

  Can I replace the HP G62 laptop keyboard? where I can buy a keyboard, help me

  Please see the sevice manual (Page # 53) below

  http://h10032.www1.HP.com/CTG/manual/c02542102.PDF

  Use the part # of the repair and order it from HP directly on here or anywhere else such as Ebay, Google, etc.

• How can I get my office hybernation mode?

  My son accidentally hit the key Crescent Moon on my Pavilion desktop computer keyboard.  We run Windows 7.  I can't get out of hybernation.  So far, we have tried: 1. push all keys on the keyboard.  2 hard reboot 3.  unplug and restart.  Any advice on how to recover my computer?

  Thank you.

  You will have to reset the BIOS. Look in this upgrade and the sevice manual under remove the side panel and the use of the mother board specifications document (clear the BIOS settings).

  For security reasons, your PC must be disconnected before performing the following procedure

  1. temporarily jumper CLR_CMOS value pin 2-3

  2. wait 5-10 seconds, and then return the jumper on pins 1-2.

  3. When you start the PC, you will need to enter the BIOS Setup to reset your custom BIOS settings. (Date/time)

  

  Once you have done this, closed the side panel and reconnected everything it's time to turn on your PC again. Everything should be back as it was before they hit the Hibernate button inadvertently.

  Best regards

  ERICO

• Windows Wireless Network must be started manually after you start the computer to the top.

  Have been able to automatically connect to my home wireless network for 3 years.
  All of a sudden the wireless connection fails to start. Right clicking and selecting 'Diagnose and fix' update option 'start Wireless Network '. By clicking on this solves the problem until the computer is restarted.
  So, how can I make it permanent as it used to be? (Note: bluetooth and WiFi lights are light up front and aftering diagnosis)
  Of course some service, etc. has changed, but I can't understand which should be set to 'automatic' or missing etc service/process.

  Notes:
  I put everything as advised by the site of Black Viper for Vista Ultimate SP1 standard (sevices.msc).
  Startup is normal (msconfig)
  Network and sharing Center is attributed to all (except password protected sharing)

  System: Dell XPS M2010 (no hardware changes - all original)
  OS: Vista Ultimate with XP1 update (not install them, re-installed original)

  Any advice greatly appreciated.

  Wayne

  Hi James

  Tried SFC/scannow - no problem found.

  I tried services.msc - noticed WLAN on manual, set to auto, rebooted, the problem seems to be solved.

  The big question is how does 'manual' - no account required to this idea is the only way that it connects to the home network and Internet.

  So just to let it auto update do its thing and reload the Windows updates that may have been cancelled.

  Grateful for your assistance.

  Concerning
  Wayne

• from readers require manual connect

  We organize several vaults file AFP/SMB interview about 30 workstations, which now require manually hit 'connect' on the window of connection for each server. We checked the username/password to inhabit the keychain of the local machine (that we don't store the trousseau on the cloud), and all drives are listed in user "Login Items" list. This issue was not a problem on El Capitan, or earlier.

  Thanks in advance

  This question was for the first time in the beta versions of Sierra. It was not fixed at the time of the release. Maybe it will be fixed in an update of the Sierra...

• How to manually lock iwatch with last software update

  The last update, I am unable to manually lock my iwatch

  Hello

  To manually lock Apple Watch under watch OS 3:

  • When you display the time on your watch, drag upward on the screen to open the control center > press the button with a lock icon to lock your watch (you may need to scroll to see it).

• Thunderbolt manual bridge IP no longer works with Sierra

  I use a Thunderbolt bridge with manual IP connection to connect 3 mac to my main MacPro, since the update of Sierra I can't connect one of the mac via the manual / plus static IP.

  Please HELP, am I missing something? It has worked before and now it no longer work.

  Joe

  Anyone?

  My work is stationary, and my staff is looking at me.

  Help, please!

  I also note that since the Sierra update whenever I connect to the server via the LAN cable or stroke, it appears this box, -that use only to appear only once (when I put in place) and hten again, unless I have re - install the operating system.

  Perhapse it is a new way to set up an IP Maunaul or I've never done right. Help, please.

  I pay my staff to do nothing right now.

• Setup Airport Express: how to manually set the IP address and DNS?

  I just bought an Airport Express for the wifi in the ethernet cable that I have in my dorm room.

  To connect to the internet via the ethernet cable, I need to enter a number IP, DNS, gateway and mask provided by the dorm (as I did on my Macbook).

  The problem is that I don't see where I can do for the Airport Express. After I plugged the cable into it, it keeps wanting to configuration alone, which does not work (he's trying to "join the network" forever, without success).

  How can I configure IP, DNS etc. manually?

  Thank you much for the help

  Hello!

  I read the post and found article suggested for her: OS X El Capitan: connect to the Internet or a network using Ethernet

  Thank you!

• Impossible to manually configure the wireless settings.

  I have an Apple Time Capsule of 7.7.7 version and no matter what I do I can't seem to accept my manual settings wireless.  My building a House requires several APs to provide adequate coverage, and time Capsule keeps selecting wireless channels that are in conflict with other access points in the House.  Does anyone know of a work around that will allow me to force the desired channels? I use a Windows PC 10 with Airport Utility for Windows version 5.6.1 configure time Capsule. Here are the steps I followed:

  -Select the "Time Capsule" on the left side

  -Click on the "Manual Configuration" button at the bottom

  -Select the tab "wireless".

  -Radio mode - menu drop down select "802. 11A / n - 802. "11b / g ' (very intentional)

  -Radio channel selection - I select in the drop-down "manual."

  -Select 'change... '. "and choose"36"for the 5 GHz channel and '1' for channel 2.4 GHz, then 'Ok '.

  -Select "Update."

  After restarting the device, I check the settings and I find...

  -Radio mode is back 'automatic '.

  -Selection of the radio channel is 'Automatic' and channels do not necessarily match what I selected initially.

  Someone at - it advice?

  The main problem is that the version of the AirPort for Windows utility is not designed to work with 802.11ac airport base stations. Unfortunately, Apple has not updated this utility since Windows 7.

  The other problem is that Apple has "dumb - which crashed" AirPort Utility for Macs and the iOS devices with version 6.x. One of the things that he removed has the possibility to define patterns of radio and channels that "stick" to the 802.11ac base stations.

• need a manual for series 2

  Where can I find a series 2 manual. Can't see series1

  Hello

  Apple Watch user guide is available here:

  https://help.Apple.com/watch/

  It includes reference to the features of the series 2, if applicable.

• I can not pair my Apple Watch with my iphone 6 s so true the automatic procedure freezes the app on my iphone. If manually matching the 6 digit code will appear on the Apple Watch. I have the current ios 10.0.1

  I can not pair my Apple Watch with my iphone 6 s so true the automatic procedure freezes the app on my iphone. If manually matching the 6 digit code will appear on the Apple Watch. I have the current ios 10.0.1

  does anyone have a solution to this?

  Hello

  The following steps can help (try again after each):

  • On your iPhone, in the application of the watch, go to: Watch My > general > use > software update - remove any file update, if one is displayed.
  • Delete all profiles beta (on your iPhone and/or the watch), then restart both devices (this applies only if you have already participated in a program of Apple Beta software).
  • Restart your iPhone and your watch:
    • Close open applications on your iPhone:
      • Double-click the Home button, and then drag upward on each Preview app to close.
    • Close the two devices together, and then restart your iPhone first.
      • Restart your iPhone, iPad or iPod touch - Apple Support
      • Restart your Apple Watch - Apple Support

• How to add manual iOS app health data?

  I use Apple Watch series 1 with Watch OS 3.

  Very useful for me has been adding data to guide health app. Now with OS3 shows, I couldn't find these options.

  Can someone help me in this case?

  Thank you, Michael

  Hi Michael

  To manually add data in the application of health:

  • On your iPhone, open the application of health.
  • Click on the data the health tab.
    • If you are not initially on the main screen of healthcare data, type on the "< health data ' link (top-right) to get back to it.
  • Select the category of data that you want to add:
    • Activity, Mindfulness, Nutrition, sleep, measurements of the body, health, reproductive health, results, vital records.
  • On the next screen, tap the metric you want to add:
    • Parameters that already contain data for the current week are displayed in the box format, with current totals.
    • Others are listed below in the list format, under "No. saved data.
    • Whether in box form or list form, tap to select the metric.
    • For example: If you chose healthcare, you can then select the blood sugar.
  • On the next screen, press the "+" (top right), then add your data and press Add (top-right) when finished.

  More information:

  Use the app on your iPhone or iPod touch - Apple Support health

• Manual lap (or segment) the pace and distance

  Is there a way (or will there be a way) to see tour distance and pace on the lookout for series 2? I want to set manual towers (or "segments") on trips and see my stats in real time, and not only in the application phone later. I've used this feature on my garmin all the time and it is very useful when the PACE work or attend training sessions. I also use strava, but I don't see either this function in their application.

  Hello

  To mark a segment (for example a tower) year running, double-tap the screen, then wait the segment summary appears in the display.

  More information:

  Work with your Apple Watch - Apple Support

• Health after app updated iOS at level 10, can't enter manually blood sugar longer?

  After the upgrade to iOS 10 can I enter is no longer blood sugar? I followed my blood sugar every day for years. It seems now there is no way to do it manually. WHA' happened?

  Try these general steps. They could help.

  1 reset your iPhone by pressing and holding the sleep/wake and home buttons.

  2 disconnect you from your iCloud account and reconnect again.