Signature of IPS 4003/0 - NMAP UDP from the outside W2K3 DNS server

Similar Questions

• Telnet to the PIX from the outside

  I tried the task through several suggestions.

  None of which worked. My last try was using this link.

  http://www.Cisco.com/en/us/customer/products/sw/secursw/ps2120/products_user_guide_chapter09186a0080089bd6.html

  PIX VPN client works fine however I am still unable to telnet to the PIX.

  In addition, the document speaks of configuration on the client.

  Step 3 in the VPN client, create a security policy that specifies the IP address of the remote party identity and IP gateway under the same IP address IP address of the external interface of the PIX firewall. In this example, the IP address of the PIX firewall outside is 168.20.1.5.

  I see there is only one place to put an IP address on the client. There is no place on the client to a gateway address. I tried to change my gateway machine and it still does not work.

  Does anyone have a config to work on how to Telnet to a PIX from the outside?

  The step that you are referencing is for users who use the old client VPN CiscoSecure. Do you really use that? I'm guessing that you are actually using the VPN client 3000, in which case you just have:

  (1) an acl of encryption that allows the traffic of your address has been assigned outside the pix

  (2) a statement of telnet that allows telnet address assigned from outside

  i.e.

  no_nat of ip host 200.1.1.1 access list permit 10.1.1.100

  Telnet 10.1.1.100 255.255.255.255 outside

  HTH

  Jeff

• How can I connect to my webserver VM from the outside?

  I'm sure that there is an easy solution for this, but I searched without success.

  I run a Web server on FreeBSD in Fusion, and my Mac uses DHCP (static address can come in time).

  My VM (fusion 2.0.1) is connected through NAT, I also use my Mac as a local server for testing, but only to listen on 127.0.0.1

  Here's my question simply:

  My FreeBSD runs Apache and is set up to serve the site (example.com, say) and DNS settings are all up to date. (I know that the BSD Web server works fine because I can connect from Safari using the merger IP address directly).

  Now if from the outside (you, for example), type http://example.com/ in your browser, connect to my Mac via port 80 and Apache on my Mac will attempt to server web page. But what I really want, it's demand to go on the virtual machine without going through the Mac. (In analogies, there is a setting that allows some ports go 'on' the virtual machine, but merging doesn't seem to have it - I promise to change the merger, because it works best with FreeBSD).

  So in short:

  How to configure my machine Virtual Port 80, rather than the Mac doing listening to?

  MacGruder says:

  So in short: How do I set up my VM to Port 80, rather than the Mac doing listening to?

  I introduce it more as a proof of concept, then a full step by step guide because there are many variables and you did not really a complete topology of your local network and other relevant information to be explicit and accurate on a total scope of the project.

  Good on my MBP without Apache running in OS X and a Virtual Machine of defined merger on NAT with Apache running on the client, I modified the nat.conf and reset the VMware network and was able to directly access Web Server of the customer from another physical Machine on my local network.

  OS X host IP address: 192.168.1.100

  Merge comments NAT IP address: 172.16.172.128

  Another physical Machine on the LAN IP address: 192.168.1.3

  Named Fusion comments: webtest

  Installed the Apache server in comments and editing the web page by default so you can be sure I look what I expect to be looking at and not the host content of the Apache server.

  Stop and closed Fusion comments

  Edited "/ Library/Application Support/VMware Fusion/vmnet8/nat.conf" and added 80 = 172.16.172.128:80

  Restarted network VMware with: sudo "/ Library/Application Support/VMware Fusion/boot.sh"-restart

  Open fusion and began comments

  Editing another physical Machine on the LAN hosts file to add: 192.168.1.100 webtest webtest.com www.webtest.com

  Browser open on another physical Machine on LAN and typed http://www.webtest.com

  Now, I'm looking at the modified Apache file index.html.en default server prompt so it allows me to know that I can access a Web server on the Guest NATed through the Port 80 of the host of another system other then the host.

  Notes:

  Personal firewall should of course be properly defined to allow connectivity between the systems.

  If you what the outside world can then access if your host doesn't have a static IP address, then you will need to use a form any Dynamic DNS on the host computer.

  It is in any case just to let you know it is possible and it's just one of the ways of May to go on this subject and without all the relevant information, I don't have the time to enter in other scenarios.

  Hope that helps!

  Post edited by: WoodyZ

  Added the second - to - restart

• How to make a link in flash from the outside

  This is something I have on my todo - or lookinto list if you want - for a long time.
  
  Is it possible for orders to push in a flash from the outside site? For example, navigate a specific image within the flash animation? I don't have a way myself, or seen websites that make this thing yet, butperhaps AS3 will allow this?
  
  Kind regards

  Of course you can do that, to implement through the Flash.ExternalInterface class.

  See you soon,.
  Gorka
  www.AquiGorka.com

• Is clickfree a good hard drive from the outside.

  I want to buy an external drive hard to back up some files. Has anyone owned this product and will give me a note.

  External hard drives more don't need any software to use just like external hard drives.  Very few would have need of all these software, in fact.

  Some have software to do other things - such as if they have their own backup applications you can use (can't) or they have another fancy software that allows you to perform a variety of other things.  The software is on the drive itself, or can easily be downloaded from the Internet.  CD/DVD is ideal for long term storage and should be used as such-, but is almost unnecessary today * once you have an operating system on the computer *.

• 192.168.1.1 is removed from the list of DNS servers

  I have a Linksys E3000 and I see the gateway (192.168.1.1) in my DNS server address.

  1. why this figure here in the DNS?

  2. how to remove from my DNS servers or stop the router insert it into my list of DNS servers?

  Tchard wrote:

  I have a Linksys E3000 and I see the gateway (192.168.1.1) in my DNS server address.

  1. why this figure here in the DNS?

  2. how to remove from my DNS servers or stop the router insert it into my list of DNS servers?

  I have an EA3500 with the latest firmware and there is a problem that HE never used "CPCI DNS" parameters through the router UI even if your connected devices shows these DNS addresses under 'ipconfig/all '.

  If you set manually the DNS settings of the card interface NETWORK (using Google or other DNS servers), then you will see that the gateway or default router address is not liseted in your list of DNS servers.

• Of SSL VPN is not able to access from the outside

  Configuration SSL VPN, unable to access from outside, when trying to access the browser site, it says "cannot display the Page.

  Area basic firewall is configured, there must be something that I'm missing, please see the attached config.

  Any help please

  Looks like you will have to allow SSL VPN from the WAN traffic to the free zone (ZP-WAN-to-self), so you need to update the political map (PMAP-JM-WAN) in particular the ACL (ACL-VPN-PROTOCOL), must allow access to port 443 of any source IP address:

  permit tcp any  eq 443

  .. .should do the trick. Cheers, Seb.

• Jabber "work' from the outside (internet) don't"work"well internally.

  Hi all

  I had problems with my jabber,

  in my case, I just use the local DNS server for internal jabber client and use host etc. for external jabber client in the laptop.

  Logon and the intercom call jabber works fine, , but I can not connect use jabber from outside (internet).

  There is no firewall in my LAB topology,

  just:

  -> MCU 5310

  public-> router-> switch-> VCS-E (static NAT 1:1)

  -> VCS - C

  -> TMS

  VCS-E use single NIC and it using a NAT 1:1 to the public.

  and here's a screenshot of my VCS E DNS and VCS - C research.

  

  

  Please advise...

  Thank you

  Ovindo

  Hello!

  In short, if you use the 1:1 NAT it is mandatory to have the 'dual interface option', even if you only

  use an interface, but allows a field set the external nat IP.

  Also all communications to this interface must go to the external ip address.

  You want to use the records SRV records in addition has if this area must be accessible.

  Learn about deployment guides, including:

  http://www.Cisco.com/en/us/docs/Telepresence/infrastructure/VCs/config_guide/Cisco_VCS_Basic_Configuration_Control_with_Expressway_Deployment_Guide_X7-2.PDF

  In addition, there are several assignments similar issues here in the forum, please use the search or google.

  Please remember useful frequency responses and identify useful or correct answers.

• Is it possible to disable or remove an add-on from the outside of the FF (it does not start after adding an addon)

  I installed the addon and now FF won't start and seems to be a loop. Is it possible to uninstall the addon or configure FF so that it starts with disabled addons? Don't forget that FF does not at all so I don't have access to one of the internal functions.

  Release the FF is 17.0.1, on Windiows XP/SP3

  In addition, as soon as I did this, I would have the addon added to the red list.

  Open Firefox in Safe Mode diagnosis by holding down the SHIFT key when you start Firefox. Firefox will start with Extensions and some other things off. When done with the Safe Mode, the release of Firefox, wait a few seconds and click the Firefox desktop icon to start Firefox in normal mode.

  More info on who and by removing manually extensions, if any, included in the following articles:

  • https://support.Mozilla.org/en-us/KB/cannot uninstall an add-on
  • http://KB.mozillazine.org/Uninstalling_extensions

  Additional follow-up questions:

  • Name of the add-on?
  • Link to which you downloaded the add-on?
  • Was this a separate application? If Yes, have you looked in Control Panel > add or remove programs (or programs and features) to see if it is listed and remove from there?

• How to call a function inside a canvas from the outside?

  Hey,.

  I created a HTML5 Canvas animation with animate CC and also added some bootstrap stuff to the HTML document by hand. To animate CC, on the main timeline, I added a function:

  this.removeObject = function() {}

  Console.log ("withdrawal of object");

  // [...]

  }

  Outside the canvas element, I added a button. When you click on it it must call the function removeObject inside the canvas.

  I tried to access by adding a "= window.parent.canvasTimeline;" Variable in the file CC animate, but it does not work.

  Is it still possible?

  It is of course possible. Just have your code Animate stash a reference to your function in the global scope.

  globalMyAnimateRemoveObjectFunction = this.removeObject;

  Then you can make globalMyAnimateRemoveObjectFunction() from anywhere in the page.

• Not able to download files with the iPhone from the outside

  Hello

  I'm not able to download files from my iPhone when the iPhone connects to the workspace to external. We have deployed nginx as reverse proxy in our DMZ which transmits requests internally will bridge.

  The download start (number of bytes transferred to the top), then the transfer ends with "error".

  I could not find errors in the log files, but maybe I didn't look in the right places

  If the iPhone is connected to the internal workspace, the problem does not occur

  Any ideas on this subject?

  Thank you

  What is the waiting period that you define in the nginx Server in the DMZ? All other additional configurations?

• How to make a components functions or eventhandlers visible from the outside

  Afternoon,

  I created a custom component with some public functions called function1, function2 function3 (no real names) my question is I am willing to do the below

  < custom: Com1 height = "100%" width = "100%" function1 = "{this.someFunction}" / > "

  problem is that the function1 is not visible outside Com1,

  My second question is how do I mark my functions as events, so when you look at intellisense they lightning rather than methods I think that the two are closely linked.

  few things are more my code for all my components is separated from my mxml via setting one actionscript actionscript for the parent class, and the class extends hbox or application. hope this makes sense, I am a vb developer not an actionscripter, which is probably why I'm doing something obviously wrong...

  Thanks in advance for any help

  See you soon

  Tom.

  1. you must tell you all that this component has events

  [Event (name = "showPreview", type = "flash.events.Event")]

  2 dispatches the event when it comes

  private void clickHandler(event:MouseEvent):void

  {

  var eventObject:Event = new Event ("showPreview");

  dispatchEvent (eventObject);

  }

  3 listen to the event from outside the component

  customComponent:Component showPreview = "showPreviewHandler (event)" / > "

  4 handle the event.

  private void showPreviewHandler(event:Event):void

  {

  }

• transfer of data from the sql for oracle server

  Can we use the tools datapumps or oracle exp in oracle to transfer data from oracle to sql server database? Is it possible to do through the use of these tools expdp or exp in oracle. Create oracle dump files and import them to sql server?
  I know there are third-party tools for the same. but I'm just curious?

  No, these tools cannot be used for the transfer of data from oracle to sql server. The two write files in an oracle proprietary format, that they not fixed data or sql scripits files.

• New ThinkPad T460p just arrived - the product name and serial number missing from the outside of the machine

  This page shows where the product name and serial number should supposed to be on my ThinkPad: https://support.lenovo.com/us/en/find-product-name?cid=EDM_2016_NA_US_PP_SUPPORT_V2&RRID=1014681098&...

  However, any of these are displayed on the outside of my machine anywhere.

  I happen to know the product name and serial number. I was able to find other ways - that is not the issue. As far as I know, these physical labels should have with the machine.

  Was it simply a mistake during Assembly, or Lenovo just stopped putting on these labels? If the first case, is there a way to ask Lenovo send me these labels? If the latter, Lenovo might consider updating the page linked above.

  Any inisight would be duly appreciated.

  Nicholas

  My T460p shows the T460p at the bottom right of the screen and the serial number and the code of the product under the battery. But the T460 is very dark on the corner of the screen, and Seraglio/product numbers appear on the very dark black label under the battery.

• can I see when my computer has been accessed from the outside of my house?

  Suspect someone may be using my free wi - fi connection.

  Hi B1lz,

  Change your router password AND the password to the router by default if you think he has been compromised (and you need to change all of your computers that use it as well because otherwise they will not be recognized once you change the settings of the router).  If your router is not configured properly (or if it is, but you feel nervous anyway), this is the solution.

  Rather than trying to find out if this is the case - keep him and KNOW that it is not.

  If you want to check, then for more details (and further explanations as well as many related articles on the sides with additional information which, when combined, will make you an expert), start here: http://www.ehow.com/how_6974931_see-someone-logging-computer-router.html.

  Good luck!