Site IPSec between RPS and IOS.
Hello
I really hope that Andrew Hickman, author of DOC-16927 and DOC-23028 can help with this.
I created a Site to IPSec VPN between our SRP527W-U and CISCO881-K9 (SRI) running IOS 15.0 (1) M3.
It is the first branch to use a PRV. I use a card dynamic encryption (that we have more than one branch, and ESP was a dynamic public IP address).
Our other branch (also runs an international search report) is a GRE over IPSec VPN, traffic between subnets it passes over the GRE tunnel. It works very well. The goal here is really to achieve the same (GRE over IPSec) between the SRP and the SRI. Similar to our other branch.
The ISAKMP and IPSec on SRI config:
crypto ISAKMP policy 1
BA 3des
preshared authentication
Group 2
ISAKMP crypto key SECRET KEY address 0.0.0.0 0.0.0.0
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
crypto dynamic-map DynMap1 10
game of transformation-ESP-3DES-SHA
PFS group2 Set
match address VPN
QoS before filing
card crypto 10 Vpn1-isakmp dynamic ipsec DynMap1
list of IP - VPN access scope
allow accord host
ip permit 172.16.0.0 0.0.0.255 172.16.2.0 0.0.0.255
interface FastEthernet4
IP address
card crypto Vpn1
Router A - CISCO881-K9 (hub) | Router B - SRP527W-U (speak) |
---|---|
Network: 172.16.0.0/24 | Network: 172.16.2.0/24 |
LAN IP: 172.16.0.1 | LAN IP: 172.16.2.1 |
WAN IP: 203.174.188.58 |
WAN: |
Starting from a host in the 172.16.2.0/24 subnet, I ping SRI (172.16.0.1) and hosts on the 172.16.0.0/24, but not the PRS (172.16.2.1) under Diagnostics-> Ping Test.
Starting from a host on the subnet 172.16.0.0/24, I ping a host on the 172.16.2.0/24 network, but not the RPS (172.16.2.1). I can confirm SPI Firewall Protection is off and filter Internet requests anonymous check box is cleared.
While Sri (172.16.0.1), I can not ping RPS (172.16.2.1) or all the 172.16.2.0/24 subnet hosts.
Summary of Ping results
The host subnet a host <-->subnet B: Yes
A <-->B router the subnet host: No.
Router, the host of a-> B subnet: No.
Router a router <-->B: No.
Hosts on the subnet B-> A router: Yes
SRI routing table
* 0.0.0.0/0 [1/0] via
10.0.0.0/8 is variably divided into subnets, 2 subnets, 2 masks
C 10.0.0.0/24 is directly connected, Tunnel0
L 10.0.0.1/32 is directly connected, Tunnel0
172.16.0.0/16 is variably divided into subnets, 3 subnets, 2 masks
C 172.16.0.0/24 is directly connected, Vlan1
L 172.16.0.1/32 is directly connected, Vlan1
S 172.16.1.0/24 [1/0] via 10.0.0.2
The RPS routing table-->-->-->
10.64.64.74 | 255.255.255.255 | -- | ppp10 |
10.64.64.74 | 255.255.255.255 | -- | ipsec0 |
172.16.2.0 | 255.255.255.0 | -- | VLAN.1 |
172.16.0.0 | 255.255.255.0 | 10.64.64.74 | ipsec0 |
0.0.0.0 | 0.0.0.0 | 10.64.64.74 | ppp10 |
I suspect it's an ACL / route question. I would gladly of assistance from anyone. According to me, that I'm so close, just not there.
Thank you very much
Trent Renshaw
Hi Trent,
My apologies, I misread your first post - I thought that you were talking about the question of access and the IP address of the PRS via IPSec (that part is fixed).
I fear for your real question, there is no answer. The SRP500 does not support GRE over IPSec (just one or the other).
Kind regards
Andy
Tags: Cisco Support
Similar Questions
-
Troubleshooting IPSec Site to Site VPN between ASA and 1841
Hi all
in the past I've implemented several VPN connections between the devices of the SAA. So I thought a site link between an ASA site and 1841 would be easier... But it seems I was mistaken.
I configured a VPN Site to Site, as it has been described in the Document ID: SDM 110198: IPsec Site to Site VPN between ASA/PIX and an example of IOS Router Configuration (I have not used SDM but CCP).
I have run the wizards on the ASA with ASDM and the current IOS version 15.1 1841, with CCP.
It seems to Phase 1 and 2 are coming although my ASA in ADSM reports (monitoring > VPN > VPN statistics > Sessions) a tunnel established with some of the Tx traffic but 0 Rx traffic),
On the ASA:
Output of the command: "sh crypto ipsec its peer 217.xx.yy.zz.
address of the peers: 217.86.154.120
Crypto map tag: VPN-OUTSIDE, seq num: 2, local addr: 62.aa.bb.ccaccess extensive list ip 192.168.37.0 outside_2_cryptomap_1 allow 255.255.255.0 172.20.2.0 255.255.255.0
local ident (addr, mask, prot, port): (LAN-A/255.255.255.0/0/0)
Remote ident (addr, mask, prot, port): (LAN-G/255.255.255.0/0/0)
current_peer: 217.xx.yy.zz#pkts program: 400, #pkts encrypt: 400, #pkts digest: 400
#pkts decaps: 0, #pkts decrypt: 0, #pkts check: 0
compressed #pkts: 0, unzipped #pkts: 0
#pkts uncompressed: 400, comp #pkts failed: 0, #pkts Dang failed: 0
success #frag before: 0, failures before #frag: 0, #fragments created: 0
Sent #PMTUs: 0, #PMTUs rcvd: 0, reassembly: 20th century / of frgs #decapsulated: 0
#send errors: 0, #recv errors: 0local crypto endpt. : 62.aa.bb.cc, remote Start crypto. : 217.xx.yy.zz
Path mtu 1500, fresh ipsec generals 58, media, mtu 1500
current outbound SPI: 39135054
current inbound SPI: B2E9E500SAS of the esp on arrival:
SPI: 0xB2E9E500 (3001672960)
transform: esp-3des esp-sha-hmac no compression
running parameters = {L2L, Tunnel, PFS 2 group}
slot: 0, id_conn: 100327424, crypto-map: VPN-OUTSIDE
calendar of his: service life remaining (KB/s) key: (4374000/1598)
Size IV: 8 bytes
support for replay detection: Y
Anti-replay bitmap:
0x00000000 0x00000001
outgoing esp sas:
SPI: 0 x 39135054 (957567060)
transform: esp-3des esp-sha-hmac no compression
running parameters = {L2L, Tunnel, PFS 2 group}
slot: 0, id_conn: 100327424, crypto-map: VPN-OUTSIDE
calendar of his: service life remaining (KB/s) key: (4373976/1598)
Size IV: 8 bytes
support for replay detection: Y
Anti-replay bitmap:
0x00000000 0x00000001Output of the command: "sh crypto isakmp his."
HIS active: 4
Generate a new key SA: 0 (a tunnel report Active 1 and 1 to generate a new key during the generate a new key)
Total SA IKE: 4IKE Peer: 217.xx.yy.zz
Type: L2L role: initiator
Generate a new key: no State: MM_ACTIVEOn the 1841
1841 crypto isakmp #sh its
IPv4 Crypto ISAKMP Security Association
DST CBC conn-State id
217.86.154.120 62.153.156.163 QM_IDLE 1002 ACTIVE1841 crypto ipsec #sh its
Interface: Dialer1
Tag crypto map: SDM_CMAP_1, local addr 217.86.154.120protégé of the vrf: (none)
local ident (addr, mask, prot, port): (172.20.2.0/255.255.255.0/0/0)
Remote ident (addr, mask, prot, port): (192.168.37.0/255.255.255.0/0/0)
current_peer 62.153.156.163 port 500
LICENCE, flags is {origin_is_acl},
#pkts program: encrypt 0, #pkts: 0, #pkts digest: 0
#pkts decaps: 585, #pkts decrypt: 585, #pkts check: 585
compressed #pkts: 0, unzipped #pkts: 0
#pkts uncompressed: 0, #pkts compr. has failed: 0
#pkts not unpacked: 0, #pkts decompress failed: 0
Errors #send 0, #recv 0 errorslocal crypto endpt. : 217.86.154.120, remote Start crypto. : 62.153.156.163
Path mtu 1452, ip mtu 1452, ip mtu BID Dialer1
current outbound SPI: 0xB2E9E500 (3001672960)
PFS (Y/N): Y, Diffie-Hellman group: group2SAS of the esp on arrival:
SPI: 0 x 39135054 (957567060)
transform: esp-3des esp-sha-hmac.
running parameters = {Tunnel}
Conn ID: 2003, flow_id: FPGA:3, sibling_flags 80000046, card crypto: SDM_CMAP_1
calendar of his: service life remaining (k/s) key: (4505068/1306)
Size IV: 8 bytes
support for replay detection: Y
Status: ACTIVEthe arrival ah sas:
SAS of the CFP on arrival:
outgoing esp sas:
SPI: 0xB2E9E500 (3001672960)
transform: esp-3des esp-sha-hmac.
running parameters = {Tunnel}
Conn ID: 2004, flow_id: FPGA:4, sibling_flags 80000046, card crypto: SDM_CMAP_1
calendar of his: service life remaining (k/s) key: (4505118/1306)
Size IV: 8 bytes
support for replay detection: Y
Status: ACTIVEoutgoing ah sas:
outgoing CFP sas:
Interface: virtual Network1
Tag crypto map: SDM_CMAP_1, local addr 217.86.154.120protégé of the vrf: (none)
local ident (addr, mask, prot, port): (172.20.2.0/255.255.255.0/0/0)
Remote ident (addr, mask, prot, port): (192.168.37.0/255.255.255.0/0/0)
current_peer 62.153.156.163 port 500
LICENCE, flags is {origin_is_acl},
#pkts program: encrypt 0, #pkts: 0, #pkts digest: 0
#pkts decaps: 585, #pkts decrypt: 585, #pkts check: 585
compressed #pkts: 0, unzipped #pkts: 0
#pkts uncompressed: 0, #pkts compr. has failed: 0
#pkts not unpacked: 0, #pkts decompress failed: 0
Errors #send 0, #recv 0 errorslocal crypto endpt. : 217.86.154.120, remote Start crypto. : 62.153.156.163
Path mtu 1452, ip mtu 1452, ip mtu BID Dialer1
current outbound SPI: 0xB2E9E500 (3001672960)
PFS (Y/N): Y, Diffie-Hellman group: group2SAS of the esp on arrival:
SPI: 0 x 39135054 (957567060)
transform: esp-3des esp-sha-hmac.
running parameters = {Tunnel}
Conn ID: 2003, flow_id: FPGA:3, sibling_flags 80000046, card crypto: SDM_CMAP_1
calendar of his: service life remaining (k/s) key: (4505068/1306)
Size IV: 8 bytes
support for replay detection: Y
Status: ACTIVEthe arrival ah sas:
SAS of the CFP on arrival:
outgoing esp sas:
SPI: 0xB2E9E500 (3001672960)
transform: esp-3des esp-sha-hmac.
running parameters = {Tunnel}
Conn ID: 2004, flow_id: FPGA:4, sibling_flags 80000046, card crypto: SDM_CMAP_1
calendar of his: service life remaining (k/s) key: (4505118/1306)
Size IV: 8 bytes
support for replay detection: Y
Status: ACTIVEoutgoing ah sas:
outgoing CFP sas:
It seems that the routing on the 1841 is working properly as I can tear down the tunnel and relaunch in scathing a host on the network of 1841, but not vice versa.
Trounleshoot VPN of the 1841 report shows a message like "the following sources are forwarded through the interface card crypto. (172.20.2.0 1) go to "Configure-> routing" and correct the routing table.
I have not found an error on the 1841 config so if one of the guys reading this thread has an idea I appreciate highly suspicion!
It's the running of the 1841 configuration
!
version 15.1
horodateurs service debug datetime msec
Log service timestamps datetime msec
encryption password service
!
host name 1841
!
boot-start-marker
start the system flash c1841-adventerprisek9 - mz.151 - 1.T.bin
boot-end-marker
!
logging buffered 51200 notifications
!
AAA new-model
!
!
AAA authentication login default local
!
AAA - the id of the joint session
!
iomem 20 memory size
clock timezone PCTime 1
PCTime of summer time clock day March 30, 2003 02:00 October 26, 2003 03:00
dot11 syslog
IP source-route
!
No dhcp use connected vrf ip
!
IP cef
no ip bootp Server
IP domain name test
name of the IP-server 194.25.2.129
name of the IP-server 194.25.2.130
name of the IP-server 194.25.2.131
name of the IP-server 194.25.2.132
name of the IP-server 194.25.2.133
No ipv6 cef
!
Authenticated MultiLink bundle-name Panel
!
!
object-group network phone
VoIP phone description
Home 172.20.2.50
Home 172.20.2.51
!
redundancy
!
!
controller LAN 0/0/0
atm mode
Annex symmetrical shdsl DSL-mode B
!
!
crypto ISAKMP policy 1
BA 3des
preshared authentication
Group 2
isakmp encryption key * address 62.aa.bb.cc
!
!
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
!
map SDM_CMAP_1 1 ipsec-isakmp crypto
Description Tunnel to62.aa.bb.cc
the value of 62.aa.bb.cc peer
game of transformation-ESP-3DES-SHA
PFS group2 Set
match address 100
!
!
!
interface FastEthernet0/0
DMZ description $ FW_OUTSIDE$
10.10.10.254 IP address 255.255.255.0
IP nat inside
IP virtual-reassembly
automatic duplex
automatic speed
!
interface FastEthernet0/1
Description $ETH - LAN$ $FW_INSIDE$
IP 172.20.2.254 255.255.255.0
IP access-group 100 to
IP nat inside
IP virtual-reassembly
IP tcp adjust-mss 1412
automatic duplex
automatic speed
!
ATM0/0/0 interface
no ip address
No atm ilmi-keepalive
!
point-to-point interface ATM0/0/0.1
PVC 1/32
PPPoE-client dial-pool-number 1
!
!
interface Dialer1
Description $FW_OUTSIDE$
the negotiated IP address
IP mtu 1452
NAT outside IP
IP virtual-reassembly
encapsulation ppp
Dialer pool 1
Dialer-Group 2
PPP authentication chap callin pap
PPP chap hostname xxxxxxx
PPP chap password 7 xxxxxxx8
PPP pap sent-name of user password xxxxxxx xxxxxxx 7
map SDM_CMAP_1 crypto
!
IP forward-Protocol ND
IP http server
local IP http authentication
IP http secure server
!
!
The dns server IP
IP nat inside source static tcp 10.10.10.1 808 interface Dialer1 80
IP nat inside source static tcp 10.10.10.1 25 25 Dialer1 interface
IP nat inside source overload map route SDM_RMAP_1 interface Dialer1
IP nat inside source overload map route SDM_RMAP_2 interface Dialer1
IP route 0.0.0.0 0.0.0.0 Dialer1 permanent
!
logging trap notifications
Note category of access list 1 = 2 CCP_ACL
access-list 1 permit 172.20.2.0 0.0.0.255
Note access-list category 2 CCP_ACL = 2
access-list 2 allow 10.10.10.0 0.0.0.255
Note access-list 100 category CCP_ACL = 4
Note access-list 100 IPSec rule
access-list 100 permit ip 172.20.2.0 0.0.0.255 192.168.37.0 0.0.0.255
Note CCP_ACL the access list 101 = 2 category
Note access-list 101 IPSec rule
access-list 101 deny ip 172.20.2.0 0.0.0.255 192.168.37.0 0.0.0.255
access-list 101 permit ip 172.20.2.0 0.0.0.255 any
Note access-list 102 CCP_ACL category = 2
Note access-list 102 IPSec rule
access-list 102 deny ip 172.20.2.0 0.0.0.255 192.168.37.0 0.0.0.255
access-list 102 permit ip 10.10.10.0 0.0.0.255 any
!!
allowed SDM_RMAP_1 1 route map
corresponds to the IP 101
!
allowed SDM_RMAP_2 1 route map
corresponds to the IP 102
!
!
control plan
!
!
Line con 0
line to 0
line vty 0 4
length 0
transport input telnet ssh
!
Scheduler allocate 20000 1000
NTP-Calendar Update
NTP 172.20.2.250 Server prefer
endAs I mentioned previously: suspicion is much appreciated!
Best regards
Joerg
Joerg,
ASA receives not all VPN packages because IOS does not send anything.
Try to send packets to the 1841 LAN to LAN of the ASA and see is the "sh cry ips its" on the 1841 increments the encrypted packets (there not)
The problem seems so on the side of the router.
I think that is a routing problem, but you only have one default gateway (no other channels on the router).
The ACL 100 is set to encrypt the traffic between the two subnets.
It seems that the ACL 101 is also bypassing NAT for VPN traffic.
Follow these steps:
Try running traffic of LAN router inside IP (source of ping 192.168.37.x 172.20.2.254) and see if the packages are not through the translation and obtaining encrypted.
I would also like to delete 100 ACL from the inside interface on the router because it is used for the VPN. You can create an another ACL to apply to the interface.
Federico.
-
Site to Site VPN between PIX and Linksys RV042
I am trying to create a tunnel between a 506th PIX and a Linksys RV042 vpn . I configured the Phase 1 and Phase 2 as well as the transformation defined and interested traffic and connected to the external interface, but it will not create the tunnel. Configurations are as follows:
506th PIX running IOS 6.3
part of pre authentication ISAKMP policy 40
ISAKMP policy 40 cryptographic 3des
ISAKMP policy 40 sha hash
40 2 ISAKMP policy group
ISAKMP duration strategy of life 40 86400
ISAKMP key * address 96.10.xxx.xxx netmask 255.255.255.255
access-list 101 permit ip 192.168.21.0 255.255.255.0 192.168.1.0 255.255.255.0crypto map Columbia_to_Office 10 ipsec-isakmp
crypto Columbia_to_Office 10 card matches the address 101
card crypto Columbia_to_Office 10 set peer 96.10.xxx.xxx
10 Columbia_to_Office transform-set ESP-3DES-SHA crypto card game
Columbia_to_Office interface card crypto outsideLinksys RV042
Configuration of local groups
IP only
IP address: 96.10.xxx.xxx
Type of local Security group: subnet
IP address: 192.168.1.0
Subnet mask: 255.255.255.0Configuration of the remote control groups
IP only
IP address: 66.192.xxx.xxx
Security remote control unit Type: subnet
IP address: 192.168.21.0
Subnet mask: 255.255.255.0IPSec configuration
Input mode: IKE with preshared key
Group Diffie-Hellman phase 1: group2
Phase 1 encryption: 3DES
Authentication of the phase 1: SHA1
Life of ITS phase 1: 86400
Phase2 encryption: 3DES
Phase2 authentication: SHA1
Phase2 life expectancy: 3600 seconds
Pre-shared key *.I'm a novice on the VPN. Thanks in advance for your expertise.
Yes, version PIX 6.3 does not support HS running nat or sh run crypto.
Please please post the complete config if you don't mind.
Please also try to send traffic between subnets 2 and get the output of:
See the isa scream his
See the ipsec scream his
-
Site to Site VPN between 5510 and 5505
Am trying to get a VPN site-to site and the race between a branch office and our main office. I have the settings in place, but I'm trying to determine if it's my settings or the provider DSL, Verizon.
They have a 5505 with a static IP is connected by cable modem. Their 5505 I can ping external IP of my 5510 without problem. All the settings are correct on both sides; they reflect the same settings and yet static VPN is not launched.
Is there some sort of CLI command I must issue to bring it?
Also, I was wondering if maybe my 2821 prevents all VPN traffic because it doesn't have to be re - NAT'ed to the 192.168.250.0/23 and 192.168.252.0/24 subnets.
Simply to traffic of their 192.168.40.0 in our 192.168.250.0/23 VOIP subnet subnet.
Join a basic outline. I can provide the configs for almost everything
Hello
you have two instances of sequence card crypto with parameters similar (except transform set). Get rid of the rest of sequences card crypto:
On the ASA Satellite:
no card crypto outside_map 2 match address outside_cryptomap
no card crypto outside_map 2 set pfs
no card crypto outside_map 2 peers set smivpn.sorensonmedia.com
no card crypto outside_map 2 the transform-set ESP-3DES-MD5 value
No crypto outside_map 2 set security-association life card seconds 28800
No kilobytes of life card crypto outside_map 2 set security-association 4608000
no card crypto outside_map 2 the value reverse-road
About the ASA company:
No crypto outside_map 1 game card address outside_1_cryptomap_1
no card crypto outside_map 1 set pfs
no card crypto outside_map 1 set cda.asa5505 counterpart
no card crypto outside_map 1 the value transform-set ESP-3DES-SHA
no card crypto outside_map 1 lifetime of security association set seconds 28800
No kilobytes of life card crypto outside_map 1 set security-association 4608000
no card crypto outside_map 1 the value reverse-road
Then check and capture debugs.
HTH
Sangaré
-
V26, about the differences between Android and iOS
I asked a question yesterday about the Adobe ID number that we use to create multiple Folio and track stats for Android, iPhone & iPad downloads etc. Now that v26 goes direct, it won't really be a difference between the display of our publication on Android or Apple device. We use about images and texts, really no videos used.
We used to create a good sharp vector folio for ipad, then reuse everything and put it all to "raster" and for Android devices. (we allowed just the device Android to the scale of our content)
But I'm curious...
Now that v. 26 allows PDF on the Android articles... There is really no need to create another option of folio for us.
But what about the cost?
If we just download the 1 folio to be viewed on both devices, how understand us what our publication is read on most of the platform? The service determines DPS what folio will receive a user based on the device ID?
just curious to see how this is handled.
Thank you.
Analytics is presented separately for each device. If you use SiteCatalyst, you can do various reports based on the type of device.
Neil
-
Synchronization between Windows and iOS
I've used PhotoShop Elements on Windows for quite awhile.
I make heavy use of key words.
Now we have a couple of iPads, iPhones, etc.
I'm looking for an app that will benefit from the investment I made in keyword tagging with PSE under Windows.
I would like to be able to get all my photos to my iPad. Then, perform a search by key words in a manner similar to
what I do now in organizing PSE. Also, it would be great if the albums I have on the EPS can be viewed on the devices as well.
Creative cloud is maybe a solution that could do this? I think I'll probably continue to do most of my editing on Windows.
So I don't think that I need a lot of editing on iOS. I want to large display and organization capabilities, however.
Thanks for all the tips of thoughts!
Yes, I use the iTunes sync PSE Album now.
That works very well for basic albums.
It does not support the smart Albums.
This is a limitation.
The iPad has a fantastic screen.
The interface is really nice and friendly.
I can find all kinds of applications on the iPad for photo editing.
But for the Organization, I guess that I've simply become spoiled by the organizing power of PES.
I have not found an Adobe or any other application that will do that.
I tried to Revel. It allows the creation of tags 'event '. And Albums.
But if there is something revel who focuses on existing metadata, I of course could not find.
It seemed that I could see my library in a sort of 'All media' view.
Or view where the images are ordered by date.
Maybe the update of Windows support will add this feature?
-
The CSM 5.5 transfer between Windows and IOS
I bought the software Creative Suite Master Collection 5.5 (in box) for a Windows computer. The HP computer is in its final phase of life and I intend to switch to an iMac from Apple. How can I go on transfer and upgrade my software on my new computer? Y at - it links or directions posted somewhere that describes this process? Very grateful for any help you can provide to my questions!
You asked this in another message CS5.5 moving to new computer... and I replied there... I will reply once again, for anyone who reads here
You do not put diesel in a petrol car, and you can't install Windows on a Mac programs... unless you want to install http://www.parallels.com/ "emulator" on your Mac to run Windows programs
Adobe to buy an upgrade CS6 Creative Cloud now includes Creative Suite Master Collection and features of Design Premium , you can call or you can register for the Cloud
-
Problem with the Site to Site IPSec VPN using ADSL and PPPoE
I have an IPSec site to Site VPN between a 2805 and an 1841. Both have fixed IP, but the end of 1841 uses a PPPoE and ADSL connection. The MTU that is displayed on the Dialer0 interface is 1454.
I can get the packets through the Tunnel without problem (standard pings), but don't spend larger packages.
Any suggestions?
You can apply on both. Here's a URL that explain the problem of MTU and option in detail.
http://www.Cisco.com/en/us/Tech/tk827/tk369/technologies_white_paper09186a00800d6979.shtml
Kind regards
Arul
* Please Note If this can help *.
-
No Ping response from Site to Site connection between 876 of Cisco and CheckPoint Firewall
Hello!
We try to create a Site-to-Site - connection IPSec between a Cisco 876 (local site) and a control-firewall station (remote site). Cisco 876 is not directly connected to the internet, but it is behind a router ADSL with port-forwarding, redirection of ports 500 and 4500. The configuration of the Cisco 876 running is attached to this thread. Unfortunately, I get no results when debugging the connection with the command "debug crypto isakmp" and "debug crypto ipsec".
From the point of view of Checkpoint firewall the connection seems to be implemented, but there is no response from ping.
The server in the local site to be achieved since the network behind the firewall Checkpoint has a routing entry "PEI route add [inside the ip-net Remote] 255.255.255.0 [inside the premises of intellectual property]" (see also annex current config name ip addresses).
Establishing a VPN Cisco Client connection to the same router Cisco 876 works very well.
Any help would be much appreciated!
Jakob J. Blaette
Hi Jakob,
Add my two cents here.
You should always verify that the following ports and Protocol are open:
1 - UDP port 500--> ISAKMP
2 - UDP port 4500--> NAT - T
3-protocol 50---> ESP
A LAN-to-LAN tunnel will never establish a TCP session, but it could use NAT - T (if behind a NAT). Remember that a single translation isn't a port forwarding, a LAN-to-LAN tunnel is not good unless you have a one-to-one translation of the NATted device, which I think, in your case the router is working.
HTH.
Portu.
Please note all useful messages and mark this message as a response.
-
I have a problem syncing between iPhone 5 (iOS 9.2.1) and iMac (OS 10.11.3). Purchased or updated on the iPhone apps are not copied on the iMac, during synchronization.
Howdy Paul Peeters,
I understand that you purchase apps on your iPhone and you want to synchronize on your iMac. For these applications automatically added to your iMac, you may want to activate the automatic downloads on the Mac.
This article explains what you see.
iOS 9 includes a new feature that allows you to download only the parts of a necessary application for your device. This saves the storage space on your iPhone, iPad or iPod touch when you install an application that supports this feature. Update to iOS 9, iTunes is not used to restore your applications when you restore your device. Instead of this, optimized versions of your apps download from the App Store directly on your device.
If you can see the apps on your iPhone, iPad or iPod touch, and they seem to be waiting to download, make sure that you are connected to WiFi or Internet. Once you are connected, the optimized versions of your apps download automatically to your device.
Similarly, applications that you add to your iPhone, iPad or iPod touch won't sync or transfer to iTunes on your computer. If you want to download apps from iTunes, turn on automatic downloads in iTunes preferences. You can also download previously purchased apps to iTunes.
Best regards
-
What are the differences between the services and site domain group policy and group policy?
What are the differences between the services and site domain group policy and group policy?
Server must wonder about the Technet site. http://social.technet.Microsoft.com/forums/en-us/home
-
Orders between IOS and IOS - XE devices?
Hi all
Is there a difference in order between IOS and IOS - XE routers? If Yes, can you please share more details on the same?
Thank you
Sunil Kumar
Hello
Most of the commands are the same for both IOS and IOS - XE.
Here's more information:
http://www.Cisco.com/c/en/us/products/collateral/iOS-NX-OS-software/iOS-...
HTH
-
Problem with IPsec VPN between ASA and router Cisco - ping is not response
Hello
I don't know because the IPsec VPN does not work. This is my setup (IPsec VPN between ASA and R2):
my network topology data:
LAN 1 connect ASA - 1 (inside the LAN)
PC - 10.0.1.3 255.255.255.0 10.0.1.1
ASA - GigabitEthernet 1: 10.0.1.1 255.255.255.0
-----------------------------------------------------------------
ASA - 1 Connect (LAN outide) R1
ASA - GigabitEthernet 0: 172.30.1.2 255.255.255.252
R1 - FastEthernet 0/0: 172.30.1.1 255.255.255.252
---------------------------------------------------------------------
R1 R2 to connect
R1 - FastEthernet 0/1: 172.30.2.1 255.255.255.252
R2 - FastEthernet 0/1: 172.30.2.2 255.255.255.252
R2 for lan connection 2
--------------------------------------------------------------------
R2 to connect LAN2
R2 - FastEthernet 0/0: 10.0.2.1 255.255.255.0
PC - 10.0.2.3 255.255.255.0 10.0.2.1
ASA configuration:
1 GigabitEthernet interface
nameif inside
security-level 100
IP 10.0.1.1 255.255.255.0
no downtime
interface GigabitEthernet 0
nameif outside
security-level 0
IP 172.30.1.2 255.255.255.252
no downtime
Route outside 0.0.0.0 0.0.0.0 172.30.1.1------------------------------------------------------------
access-list scope LAN1 to LAN2 ip 10.0.1.0 allow 255.255.255.0 10.0.2.0 255.255.255.0
object obj LAN
subnet 10.0.1.0 255.255.255.0
object obj remote network
10.0.2.0 subnet 255.255.255.0
NAT (inside, outside) 1 static source obj-local obj-local destination obj-remote control remote obj non-proxy-arp static-----------------------------------------------------------
IKEv1 crypto policy 10
preshared authentication
aes encryption
sha hash
Group 2
life 3600
Crypto ikev1 allow outside
crypto isakmp identity address------------------------------------------------------------
tunnel-group 172.30.2.2 type ipsec-l2l
tunnel-group 172.30.2.2 ipsec-attributes
IKEv1 pre-shared-key cisco123
Crypto ipsec transform-set esp-aes-192 ASA1TS, esp-sha-hmac ikev1-------------------------------------------------------------
card crypto ASA1VPN 10 is the LAN1 to LAN2 address
card crypto ASA1VPN 10 set peer 172.30.2.2
card crypto ASA1VPN 10 set transform-set ASA1TS ikev1
card crypto ASA1VPN set 10 security-association life seconds 3600
ASA1VPN interface card crypto outsideR2 configuration:
interface fastEthernet 0/0
IP 10.0.2.1 255.255.255.0
no downtime
interface fastEthernet 0/1
IP 172.30.2.2 255.255.255.252
no downtime-----------------------------------------------------
router RIP
version 2
Network 10.0.2.0
network 172.30.2.0------------------------------------------------------
access-list 102 permit ahp 172.30.1.2 host 172.30.2.2
access-list 102 permit esp 172.30.1.2 host 172.30.2.2
access-list 102 permit udp host 172.30.1.2 host 172.30.2.2 eq isakmp
interface fastEthernet 0/1
IP access-group 102 to------------------------------------------------------
crypto ISAKMP policy 110
preshared authentication
aes encryption
sha hash
Group 2
life 42300------------------------------------------------------
ISAKMP crypto key cisco123 address 172.30.1.2-----------------------------------------------------
Crypto ipsec transform-set esp - aes 128 R2TS------------------------------------------------------
access-list 101 permit tcp 10.0.2.0 0.0.0.255 10.0.1.0 0.0.0.255
------------------------------------------------------
R2VPN 10 ipsec-isakmp crypto map
match address 101
defined by peer 172.30.1.2
PFS Group1 Set
R2TS transformation game
86400 seconds, life of security association set
interface fastEthernet 0/1
card crypto R2VPNI don't know what the problem
Thank you
If the RIP is not absolutely necessary for you, try adding the default route to R2:
IP route 0.0.0.0 0.0.0.0 172.16.2.1
If you want to use RIP much, add permissions ACL 102:
access-list 102 permit udp any any eq 520
-
Installation of site to site VPN IPSec using PIX and ASA
/ * Style definitions * / table. MsoNormalTable {mso-style-name : « Table Normal » ; mso-tstyle-rowband-taille : 0 ; mso-tstyle-colband-taille : 0 ; mso-style-noshow:yes ; mso-style-priorité : 99 ; mso-style-qformat:yes ; mso-style-parent : » « ;" mso-rembourrage-alt : 0 à 5.4pt 0 à 5.4pt ; mso-para-margin : 0 ; mso-para-marge-bottom : .0001pt ; mso-pagination : widow-orphelin ; police-taille : 11.0pt ; famille de police : « Calibri », « sans-serif » ; mso-ascii-font-family : Calibri ; mso-ascii-theme-font : minor-latin ; mso-fareast-font-family : « Times New Roman » ; mso-fareast-theme-font : minor-fareast ; mso-hansi-font-family : Calibri ; mso-hansi-theme-font : minor-latin ; mso-bidi-font-family : « Times New Roman » ; mso-bidi-theme-font : minor-bidi ;}
I am a site configuration to site IPSec VPN using a PIX515E to site A and ASA5520 to Site B.
I have attached the lab diagram. Consider PIX and ASA are in default configuration, which means that nothing is configured on both devices.
According to the scheme
ASA5520
External interface is the level of security 11.11.10.1/248 0
The inside interface is 172.16.9.2/24 security level 100
Default route is 0.0.0.0 0.0.0.0 11.11.10.2 1
PIX515E
External interface is the level of security 123.123.10.2/248 0
The inside interface is 172.16.10.1/24 security level 100
Default route is 0.0.0.0 0.0.0.0 123.123.10.1 1
/ * Style definitions * / table. MsoNormalTable {mso-style-name : « Table Normal » ; mso-tstyle-rowband-taille : 0 ; mso-tstyle-colband-taille : 0 ; mso-style-noshow:yes ; mso-style-priorité : 99 ; mso-style-qformat:yes ; mso-style-parent : » « ;" mso-rembourrage-alt : 0 à 5.4pt 0 à 5.4pt ; mso-para-margin : 0 ; mso-para-marge-bottom : .0001pt ; mso-pagination : widow-orphelin ; police-taille : 11.0pt ; famille de police : « Calibri », « sans-serif » ; mso-ascii-font-family : Calibri ; mso-ascii-theme-font : minor-latin ; mso-fareast-font-family : « Times New Roman » ; mso-fareast-theme-font : minor-fareast ; mso-hansi-font-family : Calibri ; mso-hansi-theme-font : minor-latin ; mso-bidi-font-family : « Times New Roman » ; mso-bidi-theme-font : minor-bidi ;}
Could someone tell me how to set up this configuration? I tried but didn't workout. Here is the IKE protocol I have used.
IKE information:
IKE Encrytion OF
MD5 authentication method
Diffie Helman Group 2
Failure to life
IPSEC information:
IPsec encryption OF
MD5 authentication method
Failure to life
Please enter the following command
on asa
Sysopt connection permit VPN
on pix not sure of the syntax, I think it is
Permitted connection ipsec sysopt
What we are trying to do here is basically allowing vpn opening ports
Alternatively you can open udp 500 and esp (or port ip 50) out to in on the two firewalls
-
Private of IPSec VPN-private network between ASA and router
Hello community,
This is first time for me to configure IPSec VPN between ASA and router. I have an ASA 5540 at Headquarters and 877 router to EH Branch
Headquarters ASA summary.
Peer IP: 111.111.111.111
Local network: 10.0.0.0
Branch
Peer IP: 123.123.123.123
LAN: 192.168.1.0/24
Please can someone help me set up the vpn.
Hello
This guide covers exactly what you need:
Establishment of ASDM and SDM - http://www.netcraftsmen.net/resources/archived-articles/273.html
Tunnel VPN - ASA to the router configuration:
http://www.Cisco.com/en/us/products/ps5855/products_configuration_example09186a0080a9a7a3.shtml#ASDM
Kind regards
Jimmy
Maybe you are looking for
-
Forget a network on the iPhone and it comes back later
Tell me if this has happened to you. You go to the supermarket and there's an open wifi hotspot it which does not require a key, but you don't need this WiFi now. my iPhone connects automatically, making it difficult to receive messages because this
-
Hello I have mac pro mf839 and buy Cable HDMI to VGA but my screen (samsung) did not show something! How can it work? How to detect my monitor under macOS
-
How to set the margins of the document Pages?
I just downloaded the most recent Pages application (2015, I think) and I tried to put the margins to less than an inch on my document pages using the rule, but the margins will not spend. Is there another way to do this?
-
I spent several months to make a film of many DVDs. I was almost finished, when he started crashing. Whenever I try to open this movie. I had not changed anything on my computer. I do not have NERO. Under XP, someone said that you are limited to
-
Question of sticking with the updated Illustrator
Since the last update, I have graphic sticky questions of the Clipboard in Illustrator.It isThink for a good 20 seconds then glue an empty boxoraccidents of Illustrator.Everyone knows about this problem?Worm: 2015.2.0Win 10